Unit PlatformARMv8

Return to Unit Reference

OldStack	The address to save the stack pointer to for the current thread (Passed in r0)
NewStack	The address to restore the stack pointer from for the new thread (Passed in r1)
NewThread	The handle of the new thread to switch to (Passed in r2)
Note	At the point of the actual context switch (str sp / ldr sp) the thread stacks will look like this: (See: ARMv8ThreadSetupStack for additional information) (Base "Highest Address" of Stack) . . . . cpsr <- The current program status register value to load on return from the context switch lr/pc <- The address to return to from the context switch lr <- The lr value prior to the context switch r12 <- r11 <- r10 <- r9 <- r8 <- r7 <- r6 <- The value of these registers prior to the context switch r5 <- r4 <- r3 <- r2 <- r1 <- r0 <- d15 <- d14 <- d13 <- d12 <- d11 <- d10 <- d9 <- d8 <- The value of these floating point registers prior to the context switch d7 <- d6 <- d5 <- d4 <- d3 <- d2 <- d1 <- d0 <- fpscr <- The floating point FPSCR register fpexc <- The floating point FPEXC register (Current StackPointer points to here) . . . . (Top "Lowest Address" of Stack) This form of context switch uses r12 to save the cpsr value (and RFE to restore it). Because this context switch is called from a routine which will have saved the value of r12 (which is caller save in the ARM ABI) then we do not need to save the original value of r12. The context switch will be performed from SYS mode to SYS mode, the cpsr value will include the control bits (Mode and IRQ/FIQ state) but not the flags values. Again the ARM ABI does not require that the flags be saved by the callee and so the caller would have accounted for any needed flags before calling. If the thread to be resumed was interrupted by an IRQ or FIQ then the cpsr will also contain the flags etc as they were at the point of interrupt. We do not need to account for the state bits in the cpsr since all operations are performed in ARM mode at present. The main requirement of this routine is to ensure that the context record on the stack matches exactly that which is created on an interrupt and also that created by ThreadSetupStack for a new thread. If this is correct then the next context switch for any given thread can be either by a call to reschedule or by an interrupt. Equally a new thread can be first run from a context switch that resulted from either a call to reschedule or an interrupt. Note that this routine could use: pop (lr) pop (r12) msr cpsr_c, r12 mov pc, lr To return but that would mess up the value of r12, lr and the cpsr flags etc if the thread being resumed was interrupted by an IRQ,FIQ or SWI. The use of RFE here allows for exactly the same behaviour no matter which way the context record is saved and restored.

procedure ARMv8ContextSwitchIRQ(OldStack,NewStack:Pointer; NewThread:TThreadHandle);  assembler; nostackframe;

Description: Perform a context switch from one thread to another as a result of an interrupt request (IRQ)

OldStack	The address to save the stack pointer to for the current thread (Passed in r0)
NewStack	The address to restore the stack pointer from for the new thread (Passed in r1)
NewThread	The handle of the new thread to switch to (Passed in r2)
Note	At the point of the actual context switch (str sp / ldr sp) the thread stacks will look like this: (See: ARMv8ThreadSetupStack for additional information) (Base "Highest Address" of Stack) . . . . cpsr <- The current program status register value to load on return from the context switch lr/pc <- The address to return to from the context switch lr <- The lr value prior to the context switch r12 <- r11 <- r10 <- r9 <- r8 <- r7 <- r6 <- The value of these registers prior to the context switch r5 <- r4 <- r3 <- r2 <- r1 <- r0 <- d15 <- d14 <- d13 <- d12 <- d11 <- d10 <- d9 <- d8 <- The value of these floating point registers prior to the context switch d7 <- d6 <- d5 <- d4 <- d3 <- d2 <- d1 <- d0 <- fpscr <- The floating point FPSCR register fpexc <- The floating point FPEXC register (Current StackPointer points to here) . . . . (Top "Lowest Address" of Stack) This form of context switch relies on the IRQ handler to save the necessary registers including the lr, cpsr and other general registers from the point at which the thread was interrupted. The thread to be resumed may have been saved by a previous IRQ or by a call to the standard context switch from SchedulerReschule or it may be a new thread to be run for the first time. All of these result in the same context record on the stack and therefore can be resumed the same way. The context switch will be performed by switching to SYS mode, exchanging the stack pointers and then returning to IRQ mode.

procedure ARMv8ContextSwitchFIQ(OldStack,NewStack:Pointer; NewThread:TThreadHandle); assembler; nostackframe;

Description: Perform a context switch from one thread to another as a result of a fast interrupt request (FIQ)

OldStack	The address to save the stack pointer to for the current thread (Passed in r0)
NewStack	The address to restore the stack pointer from for the new thread (Passed in r1)
NewThread	The handle of the new thread to switch to (Passed in r2)
Note	At the point of the actual context switch (str sp / ldr sp) the thread stacks will look like this: (See: ARMv8ThreadSetupStack for additional information) (Base "Highest Address" of Stack) . . . . cpsr <- The current program status register value to load on return from the context switch lr/pc <- The address to return to from the context switch lr <- The lr value prior to the context switch r12 <- r11 <- r10 <- r9 <- r8 <- r7 <- r6 <- The value of these registers prior to the context switch r5 <- r4 <- r3 <- r2 <- r1 <- r0 <- d15 <- d14 <- d13 <- d12 <- d11 <- d10 <- d9 <- d8 <- The value of these floating point registers prior to the context switch d7 <- d6 <- d5 <- d4 <- d3 <- d2 <- d1 <- d0 <- fpscr <- The floating point FPSCR register fpexc <- The floating point FPEXC register (Current StackPointer points to here) . . . . (Top "Lowest Address" of Stack) This form of context switch relies on the FIQ handler to save the necessary registers including the lr, cpsr and other general registers from the point at which the thread was interrupted. The thread to be resumed may have been saved by a previous FIQ or by a call to the standard context switch from SchedulerReschule or it may be a new thread to be run for the first time. All of these result in the same context record on the stack and therefore can be resumed the same way. The context switch will be performed by switching to SYS mode, exchanging the stack pointers and then returning to FIQ mode.

procedure ARMv8ContextSwitchSWI(OldStack,NewStack:Pointer; NewThread:TThreadHandle); assembler; nostackframe;

Description: Perform a context switch from one thread to another as a result of a software interrupt (SWI)

OldStack	The address to save the stack pointer to for the current thread (Passed in r0)
NewStack	The address to restore the stack pointer from for the new thread (Passed in r1)
NewThread	The handle of the new thread to switch to (Passed in r2)
Note	At the point of the actual context switch (str sp / ldr sp) the thread stacks will look like this: (See: ARMv8ThreadSetupStack for additional information) (Base "Highest Address" of Stack) . . . . cpsr <- The current program status register value to load on return from the context switch lr/pc <- The address to return to from the context switch lr <- The lr value prior to the context switch r12 <- r11 <- r10 <- r9 <- r8 <- r7 <- r6 <- The value of these registers prior to the context switch r5 <- r4 <- r3 <- r2 <- r1 <- r0 <- d15 <- d14 <- d13 <- d12 <- d11 <- d10 <- d9 <- d8 <- The value of these floating point registers prior to the context switch d7 <- d6 <- d5 <- d4 <- d3 <- d2 <- d1 <- d0 <- fpscr <- The floating point FPSCR register fpexc <- The floating point FPEXC register (Current StackPointer points to here) . . . . (Top "Lowest Address" of Stack) This form of context switch relies on the SWI handler to save the necessary registers including the lr, cpsr and other general registers from the point at which the thread was interrupted. The thread to be resumed may have been saved by a previous SWI or by a call to the standard context switch from SchedulerReschule or it may be a new thread to be run for the first time. All of these result in the same context record on the stack and therefore can be resumed the same way. The context switch will be performed by switching to SYS mode, exchanging the stack pointers and then returning to SWI (SVC) mode.

function ARMv8InterlockedOr(var Target:LongInt; Value:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic OR operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedXor(var Target:LongInt; Value:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic XOR operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedAnd(var Target:LongInt; Value:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic AND operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedDecrement(var Target:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic decrement operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedIncrement(var Target:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic increment operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedExchange(var Target:LongInt; Source:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic exchange operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedAddExchange(var Target:LongInt; Source:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic add and exchange operation using LDREX/STREX

Note	See page ???

function ARMv8InterlockedCompareExchange(var Target:LongInt; Source,Compare:LongInt):LongInt; assembler; nostackframe;

Description: Perform an atomic compare and exchange operation using LDREX/STREX

Note	See page ???

function ARMv8PageTableGetEntry(Address:PtrUInt):TPageTableEntry;

Description: Get and Decode the entry in the Page Table that corresponds to the supplied virtual address

Note	None documented

function ARMv8PageTableSetEntry(const Entry:TPageTableEntry):LongWord;

Description: Encode and Set an entry in the Page Table that corresponds to the supplied virtual address

Note	None documented

function ARMv8VectorTableGetEntry(Number:LongWord):PtrUInt;

Description: Return the address of the specified vector table entry number

Note	None documented

function ARMv8VectorTableSetEntry(Number:LongWord; Address:PtrUInt):LongWord;

Description: Set the supplied address as the value of the specified vector table entry number

Note	None documented

function ARMv8FirstBitSet(Value:LongWord):LongWord; assembler; nostackframe;

Description: To be documented

Note	ARM arm states that CLZ is supported for ARMv5 and above

function ARMv8CountLeadingZeros(Value:LongWord):LongWord; assembler; nostackframe;

Description: Equivalent of the GCC Builtin function __builtin_clz

Note	ARM arm states that CLZ is supported for ARMv5 and above

ARMv8 thread functions

procedure ARMv8PrimaryInit; assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8SpinLock(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Lock an existing Spin entry

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinUnlock(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Unlock an existing Spin entry

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinLockIRQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Lock an existing Spin entry, disable IRQ and save the previous IRQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinUnlockIRQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Unlock an existing Spin entry and restore the previous IRQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinLockFIQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Lock an existing Spin entry, disable FIQ and save the previous FIQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinUnlockFIQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Unlock an existing Spin entry and restore the previous FIQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinLockIRQFIQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Lock an existing Spin entry, disable IRQ and FIQ and save the previous IRQ/FIQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinUnlockIRQFIQ(Spin:PSpinEntry):LongWord; assembler; nostackframe;

Description: Unlock an existing Spin entry and restore the previous IRQ/FIQ state

Spin	Pointer to the Spin entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8SpinCheckIRQ(Spin:PSpinEntry):Boolean;

Description: To be documented

Return	True if the mask would enable IRQ on restore, False if it would not

function ARMv8SpinCheckFIQ(Spin:PSpinEntry):Boolean;

Description: To be documented

Return	True if the mask would enable FIQ on restore, False if it would not

function ARMv8SpinExchangeIRQ(Spin1,Spin2:PSpinEntry):LongWord;

Description: To be documented

Note	None documented

function ARMv8SpinExchangeFIQ(Spin1,Spin2:PSpinEntry):LongWord;

Description: To be documented

Note	None documented

function ARMv8MutexLock(Mutex:PMutexEntry):LongWord; assembler; nostackframe;

Description: Lock an existing Mutex entry

Mutex	Pointer to the Mutex entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8MutexUnlock(Mutex:PMutexEntry):LongWord; assembler; nostackframe;

Description: Unlock an existing Mutex entry

Mutex	Pointer to the Mutex entry to lock (Passed in R0)
Return	ERROR_SUCCESS if completed or another error code on failure (Returned in R0)

function ARMv8MutexTryLock(Mutex:PMutexEntry):LongWord; assembler; nostackframe;

Description: Try to lock an existing Mutex entry

Mutex	Pointer to the Mutex entry to try to lock (Passed in R0)
Return	ERROR_SUCCESS if completed, ERROR_LOCKED if already locked or another error code on failure (Returned in R0)

function ARMv8ThreadGetCurrent:TThreadHandle; assembler; nostackframe;

Description: Get the current thread id from the c13 (Thread and process ID) register of system control coprocessor CP15

Note	See page ???

function ARMv8ThreadSetCurrent(Thread:TThreadHandle):LongWord; assembler; nostackframe;

Description: Set the current thread id in the c13 (Thread and process ID) register of system control coprocessor CP15

Note	See page ???

function ARMv8ThreadSetupStack(StackBase:Pointer; StartProc:TThreadStart; ReturnProc:TThreadEnd; Parameter:Pointer):Pointer;

Description: Set up the context record and arguments on the stack for a new thread

StackBase	Pointer to the base (highest address) of the allocated stack (as returned by ThreadAllocateStack
StartProc	The procedure the thread will start executing when resumed
ReturnProc	The procedure the thread will return to on exit
Return	Pointer to the starting address of the stack, which will be the Stack Pointer on the first context switch
Note	At the point of a context switch the thread stack will look like this: (Base "Highest Address" of Stack) . . . . cpsr <- The current program status register value to load on return from the context switch (On Interrupt: Includes the flags and control bits for the interrupted thread) (On Yield: Includes the control bits only for the yielded thread) (On Create: Includes the control bits only for the new thread) lr/pc <- The address to return to from the context switch (On Interrupt: The location the thread was at before interrupt) (On Yield: The location to return to in SchedulerReschedule) (On Create: The location of StartProc for the new thread) lr <- The lr value prior to the context switch (On Interrupt: The value of lr before the thread was interrupted) (On Yield: The location to return to in SchedulerReschedule) (On Create: The location of ReturnProc for the new thread) r12 <- r11 <- r10 <- r9 <- r8 <- r7 <- r6 <- The value of these registers prior to the context switch r5 <- (On Interrupt: The values before the thread was interrupted) r4 <- (On Yield: The values on return to SchedulerReschedule) r3 <- (On Create: The values on entry to StartProc as set by ThreadSetupStack) r2 <- r1 <- r0 <- d15 <- d14 <- d13 <- d12 <- d11 <- d10 <- d9 <- d8 <- The value of these floating point registers prior to the context switch d7 <- (On Interrupt: The values before the thread was interrupted) d6 <- (On Yield: The values on return to SchedulerReschedule) d5 <- (On Create: The values on entry to StartProc as set by ThreadSetupStack) d4 <- d3 <- d2 <- d1 <- d0 <- fpscr <- The floating point FPSCR register fpexc <- The floating point FPEXC register (Current StackPointer points to here) . . . . (Top "Lowest Address" of Stack) On exit from a standard context switch as performed by SchedulerReschedule the first value (Highest Address) of lr is used by the RFE (Return From Exception) instruction to load the pc which also loads the saved cpsr value. On exit from an IRQ or FIQ context switch as performed by SchedulerSwitch the first value (Highest Address) of lr is used by the interrupt handler to return from the interrupt. A standard context switch uses r12 to save the cpsr value (and RFE to restore it). Because the standard context switch is called from a routine which will have saved the value of r12 (which is caller save in the ARM ABI) then we do not need to save the original value of r12. An IRQ or FIQ context switch uses the SRS (Store Return State) and RFE (Return From Exception) instructions to save and restore the cpsr value from the spsr value of either IRQ or FIQ mode.

ARMv8 IRQ functions

function ARMv8DispatchIRQ(CPUID:LongWord; Thread:TThreadHandle):TThreadHandle; inline;

Description: To be documented

Note	None documented

ARMv8 FIQ functions

function ARMv8DispatchFIQ(CPUID:LongWord; Thread:TThreadHandle):TThreadHandle; inline;

Description: To be documented

Note	None documented

ARMv8 SWI functions

function ARMv8DispatchSWI(CPUID:LongWord; Thread:TThreadHandle; Request:PSystemCallRequest):TThreadHandle; inline;

Description: To be documented

Note	None documented

ARMv8 interrupt functions

procedure ARMv8ResetHandler; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMv8UndefinedInstructionHandler; assembler; nostackframe;

Description: Handle an undefined instruction exception

Note	This routine is registered as the vector for undefined instruction exception in the vector table loaded during startup

procedure ARMv8SoftwareInterruptHandler; assembler; nostackframe;

Description: Handle a software interrupt (SWI) from a system call (SVC)

Note	This routine is registered as the vector for SWI requests in the vector table loaded during startup. When the processor executes an SVC it switches to SWI mode, stores the address of the next instruction in the SWI mode link register (lr_svc) and saves the current program status register into the SWI mode saved program status register (spsr_svc). The SWI handler first saves the SWI mode lr and spsr (which represent the location and state to return to) onto the SYS mode stack using the srsdb (Store Return State Decrement Before) instruction. The SWI handler then switches to SYS mode and saves all the neccessary registers for the return to the interrupted thread before switching back to SWI mode in order to process the software interrupt. Because we arrive here from an interrupt the thread that was executing has no opportunity to save registers and will be unaware on return that it was interrupted. For this reason we must save all of the general purpose registers (r0 to r12) as well as the SYS mode link register (lr). We do not save the stack pointer (r13) because we use it to store the other registers and will return it to the correct value before we return from the SWI handler. The program counter (r15) does not need to be saved as it now points to this code. The SystemCall function should pass the parameters of the call as follows: R0 - System Call Number (eg SYSTEM_CALL_CONTEXT_SWITCH) R1 - Parameter 1 R2 - Parameter 2 R3 - Parameter 3 To process the software interrupt ?????? To return from the software interrupt ??????

procedure ARMv8PrefetchAbortHandler; assembler; nostackframe;

Description: Handle a prefetch abort exception

Note	This routine is registered as the vector for prefetch abort exception in the vector table loaded during startup

procedure ARMv8DataAbortHandler; assembler; nostackframe;

Description: Handle a data abort exception

Note	This routine is registered as the vector for data abort exception in the vector table loaded during startup

procedure ARMv8ReservedHandler; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMv8IRQHandler; assembler; nostackframe;

Description: Handle an interrupt request IRQ from an interrupt source

Note	This routine is registered as the vector for IRQ requests in the vector table loaded during startup. At the end of each instruction the processor checks the IRQ line and if triggered it will lookup the vector in the vector table and jump to the routine listed. When the processor receives an IRQ it switches to IRQ mode, stores the address of the next instruction in the IRQ mode link register (lr_irq) and saves the current program status register into the IRQ mode saved program status register (spsr_irq). The IRQ handler first saves the IRQ mode lr and spsr (which represent the location and state to return to) onto the SYS mode stack using the srsdb (Store Return State Decrement Before) instruction. The IRQ handler then switches to SYS mode and saves all the neccessary registers for the return to the interrupted thread before switching back to IRQ mode in order to process the interrupt request. Because we arrive here from an interrupt the thread that was executing has no opportunity to save registers and will be unaware on return that it was interrupted. For this reason we must save all of the general purpose registers (r0 to r12) as well as the SYS mode link register (lr). We do not save the stack pointer (r13) because we use it to store the other registers and will return it to the correct value before we return from the IRQ handler. The program counter (r15) does not need to be saved as it now points to this code. To process the interrupt request the handler calls the DispatchIRQ function which will dispatch the interrupt to a registered handler for processing. The handler must clear the interrupt source before it returns or the interrupt will simply occur again immediately once reenabled. To return from the interrupt request the handler uses the rfeia (Return From Exception Increment After) instruction which will load the pc and cpsr from the SYS mode stack.

procedure ARMv8FIQHandler; assembler; nostackframe;

Description: Handle a fast interrupt request FIQ from an interrupt source

Note	This routine is registered as the vector for FIQ requests in the vector table loaded during startup. At the end of each instruction the processor checks the FIQ line and if triggered it will lookup the vector in the vector table and jump to the routine listed. When the processor receives an FIQ it switches to FIQ mode, stores the address of the next instruction in the FIQ mode link register (lr_fiq) and saves the current program status register into the FIQ mode saved program status register (spsr_fiq). The FIQ handler first checks the spsr to determine if the task being interrupted is a normal thread or an exception or interrupt handler. The FIQ handler then saves the FIQ mode lr and spsr (which represent the location and state to return to) onto either the SYS mode or SVC mode stack using the srsdb (Store Return State Decrement Before) instruction depending on the value of spsr. The FIQ handler switches to SYS or SVC mode and saves all the neccessary registers for the return to the interrupted task before switching back to FIQ mode in order to process the interrupt request. Because we arrive here from an interrupt the task that was executing has no opportunity to save registers and will be unaware on return that it was interrupted. For this reason we must save all of the general purpose registers (r0 to r12) as well as the SYS mode link register (lr). We do not save the stack pointer (r13) because we use it to store the other registers and will return it to the correct value before we return from the FIQ handler. The program counter (r15) does not need to be saved as it now points to this code. To process the fast interrupt request the handler calls the DispatchFIQ function which will dispatch the interrupt to a registered handler for processing. The handler must clear the interrupt source before it returns or the fast interrupt will simply occur again immediately once reenabled. To return from the fast interrupt request the handler uses the rfeia (Return From Exception Increment After) instruction which will load the pc and cpsr from the stack of the current mode (SYS or SVC).

ARMv8 helper functions

function ARMv8GetFPEXC:LongWord; assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetFPSCR:LongWord; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMv8StartMMU; assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetTimerState(Timer:LongWord):LongWord; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMv8SetTimerState(Timer,State:LongWord); assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetTimerCount(Timer:LongWord):Int64; assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetTimerValue(Timer:LongWord):LongWord; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMV8SetTimerValue(Timer,Value:LongWord); assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetTimerCompare(Timer:LongWord):Int64; assembler; nostackframe;

Description: To be documented

Note	None documented

procedure ARMV8SetTimerCompare(Timer,High,Low:LongWord); assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetTimerFrequency:LongWord; assembler; nostackframe;

Description: To be documented

Note	None documented

function ARMv8GetPageTableCoarse(Address:PtrUInt):LongWord;

Description: Get the descriptor for a Coarse Page Table entry (1MB)

Note	See page ???

function ARMv8SetPageTableCoarse(Address,CoarseAddress:PtrUInt; Flags:Word):Boolean;

Description: Set the descriptor for a Coarse Page Table entry (1MB)

Note	See page ??? Caller must call ARMv8InvalidateTLB after changes if MMU is enabled

function ARMv8GetPageTableLarge(Address:PtrUInt):LongWord;

Description: Get the descriptor for a Large Page Table entry (64KB)

Note	See page ???

function ARMv8SetPageTableLarge(Address,PhysicalAddress:PtrUInt; Flags:Word):Boolean;

Description: Set the descriptor for a Large Page Table entry (64KB)

PageTable	Large Page Table descriptors must begin on a 16 longword (64 byte) boundary and be repeated for 16 consecutive longwords
Note	See page ??? Caller must call ARMv8InvalidateTLB after changes if MMU is enabled

function ARMv8GetPageTableSmall(Address:PtrUInt):LongWord;

Description: Get the descriptor for a Small Page Table entry (4KB)

Note	See page ???

function ARMv8SetPageTableSmall(Address,PhysicalAddress:PtrUInt; Flags:Word):Boolean;

Description: Set the descriptor for a Small Page Table entry (4KB)

Note	See page ??? Caller must call ARMv8InvalidateTLB after changes if MMU is enabled

function ARMv8GetPageTableSection(Address:PtrUInt):LongWord;

Description: Get the descriptor for a Page Table Section (1MB) or Supersection (16MB)

Note	See page ???

function ARMv8SetPageTableSection(Address,PhysicalAddress:PtrUInt; Flags:LongWord):Boolean;

Description: Set the descriptor for a Page Table Section (1MB)

Note	See page ??? Caller must call ARMv8InvalidateTLB after changes if MMU is enabled

function ARMv8SetPageTableSupersection(Address,PhysicalAddress:PtrUInt; Flags:LongWord):Boolean;

Description: Set the descriptor for a Page Table Supersection (16MB)

PageTable	Supersection Page Table descriptors must begin on a 16 longword (64 byte) boundary and be repeated for 16 consecutive longwords
Note	See page ??? Caller must call ARMv8InvalidateTLB after changes if MMU is enabled

Return to Unit Reference

SetWay	Set/Way/Level will be passed in r0
Note	See page B3-127 of the ARMv7 Architecture Reference Manual

SetWay	Set/Way/Level will be passed in r0
Note	See page B3-127 of the ARMv7 Architecture Reference Manual

SetWay	Set/Way/Level will be passed in r0
Note	See page B3-127 of the ARMv7 Architecture Reference Manual

Unit PlatformARMv8

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools