Unit PlatformRPi2
From Ultibo.org
Return to Unit Reference
Description
Ultibo Platform interface unit for Raspberry Pi 2
The RPi2 B has the Power LED connected to GPIO Pin 35 (Activity LED is now on GPIO Pin 47).
The RPi3 B has the Activity LED connected to the GPU, access is via a Virtual GPIO (Power LED is only accessible via the GPIO expander driver).
The RPi3 B+ has the Activity LED connected to GPIO Pin 29 (Power LED is only accessible via the GPIO expander driver).
Constants
RPi2 ARM physical to VC IO mapping
RPI2_VCIO_* RPI2_VCIO_ALIAS = BCM2836_VCIO_ALIAS;
|
The VCIO Alias (For ARM Physcial to VC IO translation) |
RPi2 ARM physical to VC bus mapping
RPI2_VCBUS_* RPI2_VCBUS_ALIAS = BCM2836_VCBUS_C_ALIAS;
|
The currently selected VCBUS Alias (For ARM Physcial to VC Bus translation) |
RPi2 secure world boot
RPI2_SECURE_* RPI2_SECURE_BOOT = $00000001;
|
If 1 then startup will attempt to switch back to secure world during boot process (Moved to ARMSecureBoot) |
RPI2_SECURE_BOOT_OFFSET = $000000D4;
|
The address of the Secure Boot marker in the ARM boot stub |
RPI2_SECURE_BOOT_MARKER = $58495052;
|
The Secure Boot marker (ASCII "RPIX") |
RPi2 address of StartupHandler on reset
RPI2_STARTUP_* RPI2_STARTUP_ADDRESS = $00008000;
|
Address of StartupHandler on Reset (Obtain from linker) |
RPi2 page table address and size
RPI2_PAGE_TABLE_* RPI2_PAGE_TABLE_BASE = $00004000;
|
Place the first level Page Table after the interrupt vectors at 0x00001000 and before the code start at 0x00008000 |
RPI2_PAGE_TABLE_SIZE = SIZE_16K;
|
ARM Cortex A7 first level Page Table is exactly 16KB in size (4096 32 bit (4 byte) entries) |
RPi2 vector table address and size
RPI2_VECTOR_TABLE_* RPI2_VECTOR_TABLE_BASE = $00001000;
|
Place the Interrupt Vector Table at 0x00001000 before the code start at 0x00008000 |
RPI2_VECTOR_TABLE_SIZE = SIZE_64;
|
The Interrupt Vector Table is exactly 64 bytes (16 32 bit (4 byte) entries) |
RPI2_VECTOR_TABLE_COUNT = 8;
|
The Interrupt Vector Table contains 8 entries on an ARMv7 device |
RPi2 CPU count
RPI2_CPU_* RPI2_CPU_COUNT = BCM2836_CPU_COUNT;
|
|
RPI2_CPU_BOOT = CPU_ID_0;
|
|
RPI2_CPU_MASK = CPU_AFFINITY_0 or CPU_AFFINITY_1 or CPU_AFFINITY_2 or CPU_AFFINITY_3;
|
RPi2 IRQ/FIQ start/routing
RPI2_IRQ_*, RPI2_FIQ_* RPI2_IRQ_START = 0;
|
System wide IRQs start at zero |
RPI2_IRQ_ROUTING = CPU_ID_0;
|
Route system wide IRQs to CPU0 |
RPI2_FIQ_ROUTING = CPU_ID_0;
|
Route system wide FIQs to CPU0 |
RPI2_IRQ_LOCAL_START = BCM2836_GPU_IRQ_COUNT + BCM2836_ARM_IRQ_COUNT;
|
Local IRQs start after GPU and ARM IRQs |
RPi2 SWI
RPI2_SWI_* RPI2_SWI_COUNT = 256;
|
Number of available SWI entries |
RPi2 core timer prescaler
RPI2_*_TIMER_* RPI2_CORE_TIMER_PRESCALER = $06AAAAAB;
|
Divide the Crystal Clock by 19.2 to give a 1MHz Core Timer |
RPI2_CORE_TIMER_FREQUENCY = 1000000;
|
The Core Timer frequency from the prescaler setting above |
RPI2_GENERIC_TIMER_FREQUENCY = 1000000;
|
The ARM Generic Timer frequency from the prescaler setting above |
RPi2 kernel image name
RPI2_KERNEL_* RPI2_KERNEL_NAME = 'kernel7.img';
|
|
RPI2_KERNEL_CONFIG = 'config.txt';
|
|
RPI2_KERNEL_COMMAND = 'cmdline.txt';
|
RPi2 GPIO power LED
RPI2_GPIO_PWRLED_* | GPIO Pin 35 | |
| Note: GPIO Pin 35 on the RPi2 is set on boot to Pull Up/Down Enable which must be cleared before using the pin | |
RPI2_GPIO_PWRLED_GPFSEL = BCM2836_GPFSEL3;
|
GPFSEL register for PWR LED |
RPI2_GPIO_PWRLED_GPSET = BCM2836_GPSET1;
|
GPSET register for PWR LED |
RPI2_GPIO_PWRLED_GPCLR = BCM2836_GPCLR1;
|
GPCLR register for PWR LED |
RPI2_GPIO_PWRLED_GPFSHIFT = 15;
|
GPFSEL register shift for PWR LED |
RPI2_GPIO_PWRLED_GPFMASK = BCM2836_GPFSEL_MASK;
|
GPFSEL register mask for PWR LED |
RPI2_GPIO_PWRLED_GPSHIFT = (35 - 32);
|
GPSET/GPCLR register shift for PWR LED |
RPI2_GPIO_PWRLED_GPMASK = BCM2836_GPSET_MASK;
|
GPSET/GPCLR register mask for PWR LED |
| GPIO Pin 35 on RPi2 | |
| See: http://www.raspberrypi.org/forums/viewtopic.php?t=72260 | |
| See also for how to control GPPUD etc: http://wiki.osdev.org/Raspberry_Pi_Bare_Bones | |
RPi2 GPIO activity LED
RPI2_GPIO_ACTLED_* | GPIO Pin 47 | |
| Note: GPIO Pin 47 on the RPi2 is Pull High instead of Pull Low, to turn on the LED use RPI2_GPIO_ACTLED_GPSET instead of RPI2_GPIO_ACTLED_GPCLR | |
RPI2_GPIO_ACTLED_GPFSEL = BCM2836_GPFSEL4;
|
GPFSEL register for ACT LED |
RPI2_GPIO_ACTLED_GPSET = BCM2836_GPSET1;
|
GPSET register for ACT LED |
RPI2_GPIO_ACTLED_GPCLR = BCM2836_GPCLR1;
|
GPCLR register for ACT LED |
RPI2_GPIO_ACTLED_GPFSHIFT = 21;
|
GPFSEL register shift for ACT LED |
RPI2_GPIO_ACTLED_GPFMASK = BCM2836_GPFSEL_MASK;
|
GPFSEL register mask for ACT LED |
RPI2_GPIO_ACTLED_GPSHIFT = (47 - 32);
|
GPSET/GPCLR register shift for ACT LED |
RPI2_GPIO_ACTLED_GPMASK = BCM2836_GPSET_MASK;
|
GPSET/GPCLR register mask for ACT LED |
RPi2 mailbox
RPI2_MAILBOX_* RPI2_MAILBOX_TIMEOUT = 100;
|
Default timeout to wait for mailbox calls to complete (Milliseconds) |
RPI2_MAILBOX_TIMEOUT_EX = 1000;
|
Extended timeout to wait for mailbox calls to complete (Milliseconds) |
RPi2 local mailbox
RPI2_LOCAL_MAILBOX_* RPI2_LOCAL_MAILBOX_TIMEOUT = 100;
|
Default timeout to wait for local mailbox calls to complete (Milliseconds) |
RPi2 framebuffer
RPI2_FRAMEBUFFER_* RPI2_FRAMEBUFFER_DESCRIPTION = 'BCM2836 Framebuffer';
|
Type definitions
None defined
Public variables
RPi2 specific Ultibo variables
RPi2Initialized:Boolean;
|
RPi2CNTVOFFLow:LongWord = 0;
|
The low 32 bits of the Virtual Counter Offset register at boot time (CPU0 only) (Set by Startup). Must be initialized to remain in .data or else rewritten to zero with .bss |
RPi2CNTVOFFHigh:LongWord = 0;
|
The high 32 bits of the Virtual Counter Offset register at boot time (CPU0 only) (Set by Startup). Must be initialized to remain in .data or else rewritten to zero with .bss |
Timer variables
TimerRegisters:PBCM2836SystemTimerRegisters;
|
Mailbox variables
Mailbox0Registers:PBCM2836Mailbox0Registers;
|
Mailbox1Registers:PBCM2836Mailbox1Registers;
|
Interrupt variables
InterruptRegisters:PBCM2836InterruptRegisters;
|
InterruptEntries:array[0..(BCM2836_GPU_IRQ_COUNT + BCM2836_ARM_IRQ_COUNT - 1)] of PInterruptEntry;
|
LocalInterruptEntries:array[RPI2_IRQ_LOCAL_START..(BCM2836_IRQ_COUNT - 1),0..(RPI2_CPU_COUNT - 1)] of PInterruptEntry;
|
System call
SystemCallEntries:array[0..RPI2_SWI_COUNT - 1] of TSystemCallEntry;
|
IRQ/FIQ
IRQEnabled:array[0..2] of LongWord;
|
3 groups of IRQs to Enable/Disable (See: TBCM2836InterruptRegisters) |
FIQEnabled:LongWord;
|
The single IRQ number to Enable as FIQ instead (See: TBCM2836InterruptRegisters) |
LocalIRQEnabled:array[0..(RPI2_CPU_COUNT - 1)] of LongWord;
|
1 group of local IRQs to Enable/Disable per CPU (See: TBCM2836ARMLocalRegisters) |
LocalFIQEnabled:array[0..(RPI2_CPU_COUNT - 1)] of LongWord;
|
1 group of local FIQs to Enable/Disable per CPU (See: TBCM2836ARMLocalRegisters) |
Watchdog variables
WatchdogRegisters:PBCM2836PMWatchdogRegisters;
|
ARM local
ARMLocalRegisters:PBCM2836ARMLocalRegisters;
|
Virtual GPIO
VirtualGPIOBuffer:TBCM2837VirtualGPIOBuffer;
|
Function declarations
Initialization functions
procedure RPi2Init;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2SecondarySwitch; assembler; nostackframe;
Description: Secondary CPU switch from HYP mode handler
| Note | None documented |
|---|
procedure RPi2SecondarySecure; assembler; nostackframe;
Description: Secondary CPU switch to secure mode handler
| Note | None documented |
|---|
procedure RPi2SecondaryHandler; assembler; nostackframe;
Description: Secondary CPU startup handler routine
| Note | None documented |
|---|
RPi2 platform functions
procedure RPi2SMPInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2BoardInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2MemoryInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2ClockInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2PowerInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2MailboxInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2InterruptInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2PeripheralInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2FramebufferInit;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2PageTableInit;
Description: Initialize the Hardware Page Tables before enabling the MMU
| Note | None documented |
|---|
procedure RPi2PowerLEDEnable;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2PowerLEDOn;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2PowerLEDOff;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2ActivityLEDEnable;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2ActivityLEDOn;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2ActivityLEDOff;
Description: To be documented
| Note | None documented |
|---|
function RPi2MailboxReceive(Mailbox,Channel:LongWord):LongWord;
Description: Receive from specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits |
|---|
procedure RPi2MailboxSend(Mailbox,Channel,Data:LongWord);
Description: Send to specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits |
|---|
function RPi2MailboxCall(Mailbox,Channel,Data:LongWord; var Response:LongWord):LongWord;
Description: Perform a transaction (Send/Receive) to specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits
Data pointer must be 16 byte aligned to allow for the 4 bit channel number |
|---|
function RPi2MailboxCallEx(Mailbox,Channel,Data:LongWord; var Response:LongWord; Timeout:LongWord):LongWord;
Description: Perform a transaction (Send/Receive) to specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits
Data pointer must be 16 byte aligned to allow for the 4 bit channel number |
|---|
function RPi2MailboxPropertyCall(Mailbox,Channel:LongWord; Data:Pointer; var Response:LongWord):LongWord;
Description: Perform a property tag transaction (Send/Receive) to specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits
Data pointer must be 16 byte aligned to allow for the 4 bit channel number |
|---|
function RPi2MailboxPropertyCallEx(Mailbox,Channel:LongWord; Data:Pointer; var Response:LongWord; Timeout:LongWord):LongWord;
Description: Perform a property tag transaction (Send/Receive) to specified mailbox on specified channel
| Note | Data = first 28 bits, Channel = last 4 bits
Data pointer must be 16 byte aligned to allow for the 4 bit channel number |
|---|
function RPi2MailboxPropertyTag(Tag:LongWord; Data:Pointer; Size:LongWord):LongWord;
Description: Request a property tag (Get/Set) from the mailbox property channel
| Data | Data does not need to include mailbox property channel header or footer. Data pointer does not need any specific alignment or caching attributes. |
|---|---|
| Size | Size must be a multiple of 4 bytes. Size must include the size of the request and response which use the same buffer. |
function RPi2RequestExIRQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;
Description: Request registration of the supplied handler to the specified IRQ number
| Note | None documented |
|---|
function RPi2ReleaseExIRQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;
Description: Request deregistration of the supplied handler from the specified IRQ number
| Note | None documented |
|---|
function RPi2RequestExFIQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;
Description: Request registration of the supplied handler to the specified FIQ number
| Note | None documented |
|---|
function RPi2ReleaseExFIQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;
Description: Request deregistration of the supplied handler from the specified FIQ number
| Note | None documented |
|---|
function RPi2RegisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2DeregisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2RegisterSystemCallEx(CPUID,Number:LongWord; Handler:TSystemCallHandler; HandlerEx:TSystemCallExHandler):LongWord;
Description: Request registration of the supplied extended handler to the specified System Call number
| Note | None documented |
|---|
function RPi2DeregisterSystemCallEx(CPUID,Number:LongWord; Handler:TSystemCallHandler; HandlerEx:TSystemCallExHandler):LongWord;
Description: Request deregistration of the supplied extended handler from the specified System Call number
| Note | None documented |
|---|
function RPi2GetInterruptEntry(Number,Instance:LongWord; var Interrupt:TInterruptEntry):LongWord;
Description: Get the interrupt entry for the specified interrupt number and instance
| Note | None documented |
|---|
function RPi2GetLocalInterruptEntry(CPUID,Number,Instance:LongWord; var Interrupt:TInterruptEntry):LongWord;
Description: Get the local interrupt entry for the specified interrupt number and instance
| Note | None documented |
|---|
function RPi2GetSystemCallEntry(Number:LongWord):TSystemCallEntry;
Description: Get the system call entry for the specified system call number
| Note | None documented |
|---|
function RPi2SystemRestart(Delay:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2SystemShutdown(Delay:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2SystemGetCommandLine:String;
Description: Get the Command Line from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2CPUGetMemory(var Address:PtrUInt; var Length:UInt64):LongWord;
Description: Get the CPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUGetState:LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2GPUGetMemory(var Address:PtrUInt; var Length:UInt64):LongWord;
Description: Get the GPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2BoardGetModel:LongWord;
Description: Get the Board Model from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2BoardGetSerial:Int64;
Description: Get the Board Serial from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2BoardGetRevision:LongWord;
Description: Get the Board Revision from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2BoardGetMACAddress:String;
Description: Get the Board MAC Address from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FirmwareGetRevision:LongWord;
Description: Get the Firmware Revision from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FirmwareGetThrottled:LongWord;
Description: Get the Firmware Throttling state from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2PowerGetWait(PowerId:LongWord):LongWord;
Description: Get the Power Wait from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2PowerGetState(PowerId:LongWord):LongWord;
Description: Get the Power State from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2PowerSetState(PowerId,State:LongWord; Wait:Boolean):LongWord;
Description: Set the Power State in the Mailbox property tags channel
| Note | Power Lock not required due to Mailbox Property Call serialization |
|---|
function RPi2ClockGetCount:LongWord;
Description: Gets the current system clock count (32 least significant bits of total)
| Note | On the Raspberry Pi this comes from the System Timer free running counter which runs at 1MHz and therefore overflows every 4295 seconds |
|---|
function RPi2ClockGetTotal:Int64;
Description: Gets the total system clock count
| Note | On the Raspberry Pi this comes from the System Timer free running counter which runs at 1MHz, the clock interrupt also uses this timer to increment the clock every second and therefore keep time. |
|---|
function RPi2ClockGetRate(ClockId:LongWord):LongWord;
Description: Get the Clock Rate from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2ClockSetRate(ClockId,Rate:LongWord; Turbo:Boolean):LongWord;
Description: Set the Clock Rate in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2ClockGetState(ClockId:LongWord):LongWord;
Description: Get the Clock State from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2ClockSetState(ClockId,State:LongWord):LongWord;
Description: Set the Clock State in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2ClockGetMinRate(ClockId:LongWord):LongWord;
Description: Get the Clock Min Rate from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2ClockGetMaxRate(ClockId:LongWord):LongWord;
Description: Get the Clock Max Rate from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2TurboGetState(TurboId:LongWord):LongWord;
Description: Get the Turbo State from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2TurboSetState(TurboId,State:LongWord):LongWord;
Description: Set the Turbo State in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VoltageGetValue(VoltageId:LongWord):LongWord;
Description: Get the Voltage Value from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VoltageSetValue(VoltageId,Value:LongWord):LongWord;
Description: Set the Voltage Value in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VoltageGetMinValue(VoltageId:LongWord):LongWord;
Description: Get the Voltage Min Value from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VoltageGetMaxValue(VoltageId:LongWord):LongWord;
Description: Get the Voltage Max Value from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2TemperatureGetCurrent(TemperatureId:LongWord):LongWord;
Description: Get the Temperature Current from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2TemperatureGetMaximum(TemperatureId:LongWord):LongWord;
Description: Get the Temperature Maximum Model from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUMemoryAllocate(Length,Alignment,Flags:LongWord):THandle;
Description: Allocate GPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUMemoryRelease(Handle:THandle):LongWord;
Description: Release GPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUMemoryLock(Handle:THandle):LongWord;
Description: Lock GPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUMemoryUnlock(Handle:THandle):LongWord;
Description: Unlock GPU Memory from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2GPUExecuteCode(Address:Pointer; R0,R1,R2,R3,R4,R5:LongWord):LongWord;
Description: Execute GPU Code from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2DispmanxHandleGet(Resource:THandle):THandle;
Description: Get Dispmanx Memory Handle from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2EDIDBlockGet(Block:LongWord; Buffer:Pointer; Length:LongWord):LongWord;
Description: Get EDID Block from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferAllocate(Alignment:LongWord; var Address,Length:LongWord):LongWord;
Description: Allocate Framebuffer from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferRelease:LongWord;
Description: Release Framebuffer from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetState(State:LongWord):LongWord;
Description: Set Framebuffer State (Blank Screen) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetDimensions(var Width,Height,Top,Bottom,Left,Right:LongWord):LongWord;
Description: Get Framebuffer Dimensions from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetPhysical(var Width,Height:LongWord):LongWord;
Description: Get Framebuffer Physical size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetPhysical(var Width,Height:LongWord):LongWord;
Description: Set Framebuffer Physical size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestPhysical(var Width,Height:LongWord):LongWord;
Description: Test Framebuffer Physical size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetVirtual(var Width,Height:LongWord):LongWord;
Description: Get Framebuffer Virtual size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetVirtual(var Width,Height:LongWord):LongWord;
Description: Set Framebuffer Virtual size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestVirtual(var Width,Height:LongWord):LongWord;
Description: Test Framebuffer Virtual size from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetDepth(var Depth:LongWord):LongWord;
Description: Get Framebuffer Depth (Bits per pixel) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetDepth(var Depth:LongWord):LongWord;
Description: Set Framebuffer Depth (Bits per pixel) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestDepth(var Depth:LongWord):LongWord;
Description: Test Framebuffer Depth (Bits per pixel) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetPixelOrder(var Order:LongWord):LongWord;
Description: Get Framebuffer Pixel Order (RGB) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetPixelOrder(var Order:LongWord):LongWord;
Description: Set Framebuffer Pixel Order (RGB) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestPixelOrder(var Order:LongWord):LongWord;
Description: Test Framebuffer Pixel Order (RGB) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetAlphaMode(var Mode:LongWord):LongWord;
Description: Get Framebuffer Alpha Mode from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetAlphaMode(var Mode:LongWord):LongWord;
Description: Set Framebuffer Alpha Mode from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestAlphaMode(var Mode:LongWord):LongWord;
Description: Test Framebuffer Alpha Mode from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetPitch:LongWord;
Description: Get Framebuffer Pitch (Bytes per line) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetOffset(var X,Y:LongWord):LongWord;
Description: Get Framebuffer Virtual Offset from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetOffset(var X,Y:LongWord):LongWord;
Description: Set Framebuffer Virtual Offset from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestOffset(var X,Y:LongWord):LongWord;
Description: Test Framebuffer Virtual Offset from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetOverscan(var Top,Bottom,Left,Right:LongWord):LongWord;
Description: Get Framebuffer Overscan from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetOverscan(var Top,Bottom,Left,Right:LongWord):LongWord;
Description: Set Framebuffer Overscan from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestOverscan(var Top,Bottom,Left,Right:LongWord):LongWord;
Description: Test Framebuffer Overscan from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetPalette(Buffer:Pointer; Length:LongWord):LongWord;
Description: Get Framebuffer Palette from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetPalette(Start,Count:LongWord; Buffer:Pointer; Length:LongWord):LongWord;
Description: Set Framebuffer Palette from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestPalette(Start,Count:LongWord; Buffer:Pointer; Length:LongWord):LongWord;
Description: Test Framebuffer Palette from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferTestVsync:LongWord;
Description: Test Framebuffer Vertical Sync from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetVsync:LongWord;
Description: Set Framebuffer Vertical Sync from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetBacklight(Brightness:LongWord):LongWord;
Description: Set Framebuffer Backlight Brightness from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetNumDisplays(var NumDisplays:LongWord):LongWord;
Description: Get the number of displays from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetDisplayId(DisplayNum:LongWord):LongWord;
Description: Get the display id for the specified display number from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferSetDisplayNum(DisplayNum:LongWord):LongWord;
Description: Get the display number that all framebuffer requests will refer to using the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferGetDisplaySettings(DisplayNum:LongWord; var DisplaySettings:TDisplaySettings):LongWord;
Description: Get the display settings for the specified display number from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2FramebufferDisplayIdToName(DisplayId:LongWord):String;
Description: Get the name for the specified display id
| Note | None documented |
|---|
function RPi2TouchGetBuffer(var Address:PtrUInt):LongWord;
Description: Get the Touchscreen buffer from the Mailbox property tags channel
| Note | On current firmware versions calling TouchGetBuffer will allocate a buffer from GPU memory and render subsequent calls to TouchSetBuffer ineffective. After an initial call to TouchSetBuffer calls to TouchGetBuffer will always return the CPU allocated buffer. |
|---|
function RPi2TouchSetBuffer(Address:PtrUInt):LongWord;
Description: Set the Touchscreen buffer in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VirtualGPIOGetBuffer(var Address:PtrUInt):LongWord;
Description: Get the Virtual GPIO buffer from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VirtualGPIOSetBuffer(Address:PtrUInt):LongWord;
Description: Set the Virtual GPIO buffer in the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2CursorSetDefault:LongWord;
Description: Set Cursor Default (Pixels) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2CursorSetInfo(Width,Height,HotspotX,HotspotY:LongWord; Pixels:Pointer; Length:LongWord):LongWord;
Description: Set Cursor Info (Pixels) from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2CursorSetState(Enabled:Boolean; X,Y:LongWord; Relative:Boolean):LongWord;
Description: Set Cursor State (Enable, X, Y) from the Mailbox property tags channel
| Relative | X, Y is relative to Display (Virtual) not Framebuffer (Physical). |
|---|
function RPi2DMAGetChannels:LongWord;
Description: Get the available DMA Channels from the Mailbox property tags channel
| Note | None documented |
|---|
function RPi2VirtualGPIOAllocate:Boolean;
Description: Allocate the Virtual GPIO buffer either from memory or from the firmware
| Note | None documented |
|---|
function RPi2VirtualGPIOInputGet(Pin:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2VirtualGPIOOutputSet(Pin,Level:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2VirtualGPIOFunctionSelect(Pin,Mode:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
RPi2 thread functions
procedure RPi2SchedulerInit;
Description: Initialize the scheduler interrupt on the boot CPU
| Note | None documented |
|---|
procedure RPi2SchedulerStart(CPUID:LongWord);
Description: Initialize the scheduler interrupt on the specified secondary CPU
| Note | None documented |
|---|
procedure RPi2SecondaryBoot(CPUID:LongWord);
Description: To be documented
| Note | None documented |
|---|
RPi2 clock functions
procedure RPi2ClockInterrupt(Parameter:Pointer);
Description: Interrupt handler function for the clock interrupt
| Note | This schedules another clock interrupt to occur CLOCK_CYCLES_PER_TICK in the future, then updates ClockTicks and ClockSeconds and checks for timers to trigger. |
|---|
procedure RPi2ClockUpdate(Cycles:LongWord; var Last:LongWord);
Description: Setup a clock interrupt to trigger after the specified number of clock cycles
| Cycles | Number of cycles after which the timer interrupt is to be triggered |
|---|---|
| Note | This refers to native clock cycles as specified by CLOCK_FREQUENCY |
RPi2 scheduler functions
function RPi2SchedulerInterrupt(CPUID:LongWord; Thread:TThreadHandle; Parameter:Pointer):TThreadHandle;
Description: Interrupt handler function for the scheduler interrupt
| Note | This schedules another scheduler interrupt to occur SCHEDULER_CLOCKS_PER_INTERRUPT in the future, then checks for threads to wakeup or timeout and the next thread to schedule. |
|---|
procedure RPi2SchedulerUpdate(Cycles:LongWord; var Last:LongWord);
Description: Setup a scheduler interrupt to trigger after the specified number of clock cycles
| Cycles | Number of cycles after which the scheduler interrupt is to be triggered |
|---|---|
| Note | This refers to native clock cycles as specified by RPI2_GENERIC_TIMER_FREQUENCY |
procedure RPi2SchedulerSystemCall(Request:PSystemCallRequest);
Description: System Call handler for the scheduler
| Note | This is registered to receive requests for the SYSTEM_CALL_CONTEXT_SWITCH and will perform a context switch from within an SWI |
|---|
RPi2 framebuffer functions
function RPi2FramebufferDeviceAllocate(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;
Description: Allocate a framebuffer using the Mailbox Property Tags
| Note | None documented |
|---|
function RPi2FramebufferDeviceAllocateAlt(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;
Description: Allocate a framebuffer using a simple Mailbox Call
| Note | None documented |
|---|
function RPi2FramebufferDeviceRelease(Framebuffer:PFramebufferDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2FramebufferDeviceBlank(Framebuffer:PFramebufferDevice; Blank:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2FramebufferDeviceCommit(Framebuffer:PFramebufferDevice; Address:PtrUInt; Size,Flags:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2FramebufferDeviceSetBacklight(Framebuffer:PFramebufferDevice; Brightness:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2FramebufferDeviceSetProperties(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;
Description: To be documented
| Note | None documented |
|---|
RPi2 helper functions
procedure RPi2Wait; assembler; nostackframe;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2LongWait; assembler; nostackframe;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2ShortWait; assembler; nostackframe;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2SlowBlink; assembler; nostackframe;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2FastBlink; assembler; nostackframe;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2BootBlink; assembler; nostackframe;
Description: Blink the Activity LED without dependency on any other RTL setup
| Note | None documented |
|---|
procedure RPi2BootConsoleStart;
Description: To be documented
| Note | None documented |
|---|
procedure RPi2BootConsoleWrite(const Value:String);
Description: To be documented
| Note | None documented |
|---|
procedure RPi2BootConsoleWriteEx(const Value:String; X,Y:LongWord);
Description: To be documented
| Note | None documented |
|---|
function RPi2BootConsoleGetX:LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2BootConsoleGetY:LongWord;
Description: To be documented
| Note | None documented |
|---|
function RPi2ConvertPowerIdRequest(PowerId:LongWord):LongWord;
Description: Convert Ultibo Power Id to BCM2836 Power Id
| Note | None documented |
|---|
function RPi2ConvertPowerStateRequest(PowerState:LongWord):LongWord;
Description: Convert Ultibo Power State to BCM2836 Power State
| Note | None documented |
|---|
function RPi2ConvertPowerStateResponse(PowerState:LongWord):LongWord;
Description: Convert BCM2836 Power State to Ultibo Power State
| Note | None documented |
|---|
function RPi2ConvertClockIdRequest(ClockId:LongWord):LongWord;
Description: Convert Ultibo Clock Id to BCM2836 Clock Id
| Note | None documented |
|---|
function RPi2ConvertClockStateRequest(ClockState:LongWord):LongWord;
Description: Convert Ultibo Clock State to BCM2836 Clock State
| Note | None documented |
|---|
function RPi2ConvertClockStateResponse(ClockState:LongWord):LongWord;
Description: Convert BCM2836 Clock State to Ultibo Clock State
| Note | None documented |
|---|
function RPi2ConvertVoltageIdRequest(VoltageId:LongWord):LongWord;
Description: Convert Ultibo Voltage Id to BCM2836 Voltage Id
| Note | None documented |
|---|
function RPi2ConvertTemperatureIdRequest(TemperatureId:LongWord):LongWord;
Description: Convert Ultibo Temperature Id to BCM2836 Temperature Id
| Note | None documented |
|---|
Return to Unit Reference
