Unit BCM2838

Return to Unit Reference

Channels 0 to 14

`BCM2838_DMA0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7000;`
`BCM2838_DMA1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7100;`
`BCM2838_DMA2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7200;`
`BCM2838_DMA3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7300;`
`BCM2838_DMA4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7400;`
`BCM2838_DMA5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7500;`
`BCM2838_DMA6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7600;`
`BCM2838_DMA7_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7700;`	Lite DMA engine
`BCM2838_DMA8_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7800;`	Lite DMA engine
`BCM2838_DMA9_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7900;`	Lite DMA engine
`BCM2838_DMA10_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7A00;`	Lite DMA engine
`BCM2838_DMA11_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7B00;`	40bit DMA engine (DMA channel 11 is able to access the PCIe interface)
`BCM2838_DMA12_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7C00;`	40bit DMA engine
`BCM2838_DMA13_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7D00;`	40bit DMA engine
`BCM2838_DMA14_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7E00;`	40bit DMA engine

`BCM2838_DMA_INT_STATUS_BASE = BCM2838_PERIPHERALS_BASE + $7FE0;`
`BCM2838_DMA_ENABLE_BASE = BCM2838_PERIPHERALS_BASE + $7FF0;`

BCM2838 ARM legacy interrupt controller BCM2838_INTERRUPT_REGS_*

`BCM2838_INTERRUPT_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B200;`	Note: Documentation states 0xB000 but the offsets begin at 0x200 so 0xB200 will be correct

BCM2838 ARM timer BCM2838_TIMER_REGS_*

`BCM2838_TIMER_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B400;`	Note: Documentation states 0xB000 but the offsets begin at 0x400 so 0xB400 will be correct

BCM2838 ARM doorbell (VCHIQ) BCM2838_DOORBELL_*

`BCM2838_DOORBELL_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B840;`
`BCM2838_VCHIQ_REGS_BASE = BCM2838_DOORBELL_REGS_BASE;`

BCM2838 ARM mailbox 0 BCM2838_MAILBOX0_*

`BCM2838_MAILBOX0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B880;`

BCM2838 ARM mailbox 1 BCM2838_MAILBOX1_*

`BCM2838_MAILBOX1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B8A0;`

BCM2838 power management, reset controller and watchdog BCM2838_PM_*

`BCM2838_PM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $100000;`

BCM2838 clock management BCM2838_CM_*

`BCM2838_CM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $101000;`

BCM2838 PCM clock BCM2838_PCM_CLOCK_*

`BCM2838_PCM_CLOCK_BASE = BCM2838_PERIPHERALS_BASE + $101098;`

BCM2838 random number generator BCM2838_RNG_REGS_*

`BCM2838_RNG_REGS_BASE = BCM2838_PERIPHERALS_BASE + $104000;`

BCM2838 GPIO BCM2838_GPIO_*

`BCM2838_GPIO_REGS_BASE = BCM2838_PERIPHERALS_BASE + $200000;`	This is shown in BCM2711 ARM Peripherals as 0x7E215000 which is thought to be an error

BCM2838 UART0 (PL011) BCM2838_PL011_*

`BCM2838_PL011_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201000;`
`BCM2838_UART0_REGS_BASE = BCM2838_PL011_REGS_BASE;`

BCM2838 UART2 (PL011) BCM2838_UART2_*

`BCM2838_UART2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201400;`

BCM2838 UART3 (PL011) BCM2838_UART3_*

`BCM2838_UART3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201600;`

BCM2838 UART4 (PL011) BCM2838_UART4_*

`BCM2838_UART4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201800;`

BCM2838 UART5 (PL011) BCM2838_UART5_*

`BCM2838_UART5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201A00;`

`BCM2838_UART0_REGS_BASES:array[0..5] of LongWord = (BCM2838_UART0_REGS_BASE, 0, BCM2838_UART2_REGS_BASE, BCM2838_UART3_REGS_BASE, BCM2838_UART4_REGS_BASE, BCM2838_UART5_REGS_BASE);`

BCM2838 EMMC1 (SDHOST) BCM2838_EMMC1_*

`BCM2838_EMMC1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $202000;`
`BCM2838_SDHOST_REGS_BASE = BCM2838_EMMC1_REGS_BASE;`

BCM2838 PCM/I2S audio BCM2838_PCM_REGS_*

`BCM2838_PCM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $203000;`

BCM2838 SPI0 BCM2838_SPI0_*

`BCM2838_SPI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204000;`

BCM2838 SPI3 BCM2838_SPI3_*

`BCM2838_SPI3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204600;`

BCM2838 SPI4 BCM2838_SPI4_*

`BCM2838_SPI4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204800;`

BCM2838 SPI5 BCM2838_SPI5_*

`BCM2838_SPI5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204A00;`

BCM2838 SPI6 BCM2838_SPI6_*

`BCM2838_SPI6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204C00;`

`BCM2838_SPI0_REGS_BASES:array[0..6] of LongWord = (BCM2838_SPI0_REGS_BASE, 0, 0, BCM2838_SPI3_REGS_BASE, BCM2838_SPI4_REGS_BASE, BCM2838_SPI5_REGS_BASE, BCM2838_SPI6_REGS_BASE);`

BCM2838 peripheral control BCM2838_PACTL_CS*

`BCM2838_PACTL_CS_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204E00;`

BCM2838 BSC0 (I2C0) (Broadcom Serial Controller) BCM2838_BSC0_*

`BCM2838_BSC0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205000;`
`BCM2838_I2C0_REGS_BASE = BCM2838_BSC0_REGS_BASE;`

BCM2838 I2C3 BCM2838_I2C3_*

`BCM2838_I2C3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205600;`

BCM2838 I2C4 BCM2838_I2C4_*

`BCM2838_I2C4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205800;`

BCM2838 I2C5 BCM2838_I2C5_*

`BCM2838_I2C5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205A00;`	Note: This is shown in BCM2711 ARM Peripherals as 0x7E205A80 which is thought to be an error

BCM2838 I2C6 BCM2838_I2C6_*

`BCM2838_I2C6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205C00;`

BCM2838 I2C7 BCM2838_I2C7_*

Note: I2C7 master is used dedicated with the HDMI interface and must not be used

`BCM2838_I2C7_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205E00;`

BCM2838 pixel valve BCM2838_PIXELVALVE0_*

`BCM2838_PIXELVALVE0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $206000;`	Pixel Valve 0
`BCM2838_PIXELVALVE1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $207000;`	Pixel Valve 1

BCM2838 DPI (Display Parallel Interface) BCM2838_DPI_*

`BCM2838_DPI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $208000;`

BCM2838 DSI0 (Display Serial Interface) BCM2838_DSI0_*

`BCM2838_DSI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $209000;`

BCM2838 PWM0 (Pulse Width Modulator) BCM2838_PWM0_*

`BCM2838_PWM0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $20C000;`

BCM2838 PWM1 (Pulse Width Modulator) BCM2838_PWM1_*

`BCM2838_PWM1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $20C800;`
`BCM2838_PWM0_REGS_BASES:array[0..1] of LongWord = (BCM2838_PWM0_REGS_BASE, BCM2838_PWM1_REGS_BASE);`

BCM2838 I2C/SPI slave BCM2838_I2CSPI_*

`BCM2838_I2CSPI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $214000;`

BCM2838 AUX (UART1, SPI1 and SPI2) BCM2838_AUX_*

`BCM2838_AUX_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215000;`
`BCM2838_UART1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215040;`
`BCM2838_SPI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215080;`
`BCM2838_SPI2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $2150C0;`

BCM2838 EMMC0 (SDHCI) BCM2838_EMMC0_*

`BCM2838_EMMC0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $300000;`
`BCM2838_SDHCI_REGS_BASE = BCM2838_EMMC0_REGS_BASE;`

BCM2838 EMMC2 BCM2838_EMMC2_*

`BCM2838_EMMC2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $340000;`

BCM2838 HVS BCM2838_HVS_*

`BCM2838_HVS_REGS_BASE = BCM2838_PERIPHERALS_BASE + $400000;`

BCM2838 SMI (Firmware KMS) BCM2838_SMI_*

`BCM2838_SMI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $600000;`
`BCM2838_FIRMWAREKMS_REGS_BASE = BCM2838_SMI_REGS_BASE;`

BCM2838 DSI1 (Display Serial Interface) BCM2838_DSI1_*

`BCM2838_DSI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $700000;`

BCM2838 CSI0 (Camera Serial Interface) BCM2838_CSI0_*

`BCM2838_CSI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $800000;`

BCM2838 CSI1 (Camera Serial Interface) BCM2838_CSI1_*

`BCM2838_CSI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $801000;`

BCM2838 BSC1 (I2C1) (Broadcom Serial Controller) BCM2838_BSC1_*

`BCM2838_BSC1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $804000;`
`BCM2838_I2C1_REGS_BASE = BCM2838_BSC1_REGS_BASE;`

BCM2838 BSC2 (I2C2) (Broadcom Serial Controller) BCM2838_BSC2_*

Note: I2C2 master is used dedicated with the HDMI interface and must not be used

`BCM2838_BSC2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $805000;`
`BCM2838_I2C2_REGS_BASE = BCM2838_BSC2_REGS_BASE;`
`BCM2838_I2C0_REGS_BASES:array[0..7] of LongWord = (BCM2838_I2C0_REGS_BASE, BCM2838_I2C1_REGS_BASE, BCM2838_I2C2_REGS_BASE, BCM2838_I2C3_REGS_BASE, BCM2838_I2C4_REGS_BASE, BCM2838_I2C5_REGS_BASE, BCM2838_I2C6_REGS_BASE, BCM2838_I2C7_REGS_BASE);`

BCM2838 VEC BCM2838_VEC_*

`BCM2838_VEC_REGS_BASE = BCM2838_PERIPHERALS_BASE + $806000;`

BCM2838 pixel valve 2 BCM2838_PIXELVALVE2_*

`BCM2838_PIXELVALVE2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $807000;`

BCM2838 HDMI BCM2838_HDMI_*

`BCM2838_HDMI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $902000;`

BCM2838 USB (Synopsys DesignWare Hi-Speed USB 2.0 On-The-Go Controller) BCM2838_USB_*

`BCM2838_USB_REGS_BASE = BCM2838_PERIPHERALS_BASE + $980000;`
`BCM2838_DWCOTG_REGS_BASE = BCM2838_USB_REGS_BASE;`

BCM2838 XHCI (Additional on chip generic XHCI USB host controller) BCM2838_XHCI_*

`BCM2838_XHCI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $9C0000;`	This is separate to the VL805 XHCI controller

BCM2838 HEVC Decoder BCM2838_HEVC_*

`BCM2838_HEVC_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B00000;`

BCM2838 ARGON BCM2838_ARGON_*

`BCM2838_ARGON_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B10000;`

BCM2838 H264 decoder BCM 2838_H264_*

`BCM 2838_H264_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B20000;`

BCM2838 VP9 decoder BCM2838_VP9_*

`BCM2838_VP9_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B30000;`

BCM2838 V3D BCM2838_V3D_*

`BCM2838_V3D_REGS_BASE = BCM2838_PERIPHERALS_BASE + $C04000;`

BCM2838 DMA controller BCM2838_DMA15_*

Channel 15 Note: DMA15 is exclusively used by the VPU

`BCM2838_DMA15_REGS_BASE = BCM2838_PERIPHERALS_BASE + $E05000;`

BCM2838 chip revision BCM2838_CHIP_REVISION_*

See: https://elinux.org/The_Undocumented_Pi#BCM2711

`BCM2838_CHIP_REVISION_BASE = BCM2838_EXT_PERIPHERALS_BASE + $404000;`

BCM2838 PCIe BCM2838_PCIE_*

`BCM2838_PCIE_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $1500000;`

BCM2838 GENET BCM2838_GENET_*

`BCM2838_GENET_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $1580000;`
`BCM2838_GENET_MDIO_OFFSET = $0E14;`

BCM2838 thermal BCM2838_THERMAL_*

`BCM2838_THERMAL_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $15D2200;`

BCM2838 IRQ peripheral BCM2838_IRQ_*

IRQ lines of BCM2838 peripherals

`BCM2838_SPI_BASE = 32;`	Added to the SPI ID in device tree to obtain the real ID
`BCM2838_PPI_BASE = 16;`	Added to the PPI ID in device tree to obtain the real ID
`BCM2838_SGI_BASE = 0;`
ARM Generic Timer
`BCM2838_IRQ_TIMER0 = BCM2838_PPI_BASE + 13;`	IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n PS timer IRQ)
`BCM2838_IRQ_TIMER1 = BCM2838_PPI_BASE + 14;`	IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n PNS timer IRQ)
`BCM2838_IRQ_TIMER2 = BCM2838_PPI_BASE + 11;`	IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n V timer IRQ)
`BCM2838_IRQ_TIMER3 = BCM2838_PPI_BASE + 10;`	IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n HP timer IRQ)
Legacy IRQ/FIQ
`BCM2838_FIQ_LEGACY = BCM2838_PPI_BASE + 12;`	Legacy FIQn
`BCM2838_IRQ_LEGACY = BCM2838_PPI_BASE + 15;`	Legacy IRQn
ARM Mailbox IRQs (BCM2838_SPI_BASE + 0 to 15)
`BCM2838_IRQ_MAILBOX0_0 = BCM2838_SPI_BASE + 0;`	IRQ_TYPE_LEVEL_HIGH(Core 0)
`BCM2838_IRQ_MAILBOX1_0 = BCM2838_SPI_BASE + 1;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX2_0 = BCM2838_SPI_BASE + 2;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX3_0 = BCM2838_SPI_BASE + 3;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX0_1 = BCM2838_SPI_BASE + 4;`	IRQ_TYPE_LEVEL_HIGH (Core 1)
`BCM2838_IRQ_MAILBOX1_1 = BCM2838_SPI_BASE + 5;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX2_1 = BCM2838_SPI_BASE + 6;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX3_1 = BCM2838_SPI_BASE + 7;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX0_2 = BCM2838_SPI_BASE + 8;`	IRQ_TYPE_LEVEL_HIGH (Core 2)
`BCM2838_IRQ_MAILBOX1_2 = BCM2838_SPI_BASE + 9;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX2_2 = BCM2838_SPI_BASE + 10;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX3_2 = BCM2838_SPI_BASE + 11;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX0_3 = BCM2838_SPI_BASE + 12;`	IRQ_TYPE_LEVEL_HIGH (Core 3)
`BCM2838_IRQ_MAILBOX1_3 = BCM2838_SPI_BASE + 13;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX2_3 = BCM2838_SPI_BASE + 14;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MAILBOX3_3 = BCM2838_SPI_BASE + 15;`	IRQ_TYPE_LEVEL_HIGH
ARM PMU
`BCM2838_IRQ_PMU0 = BCM2838_SPI_BASE + 16;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PMU1 = BCM2838_SPI_BASE + 17;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PMU2 = BCM2838_SPI_BASE + 18;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PMU3 = BCM2838_SPI_BASE + 19;`	IRQ_TYPE_LEVEL_HIGH
AXI Quiet
`BCM2838_IRQ_LOCAL_AXIQUIET = BCM2838_SPI_BASE + 20;`	IRQ_TYPE_LEVEL_HIGH
ARM Local Timer
`BCM2838_IRQ_LOCAL_TIMER = BCM2838_SPI_BASE + 21;`	IRQ_TYPE_LEVEL_HIGH
AXI Error
`BCM2838_IRQ_LOCAL_AXIERR = BCM2838_SPI_BASE + 22;`	IRQ_TYPE_LEVEL_HIGH (TBD)
ARM peripheral IRQs (BCM2838_SPI_BASE + 32 to 47)
ARM Timer
`BCM2838_IRQ_ARM_TIMER = BCM2838_SPI_BASE + 32;`	IRQ_TYPE_LEVEL_HIGH
ARM Mailbox
`BCM2838_IRQ_ARM_MAILBOX = BCM2838_SPI_BASE + 33;`	IRQ_TYPE_LEVEL_HIGH
ARM Doorbell (VCHIQ)
`BCM2838_IRQ_ARM_DOORBELL0 = BCM2838_SPI_BASE + 34;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_DOORBELL1 = BCM2838_SPI_BASE + 35;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_VCHIQ = BCM2838_IRQ_ARM_DOORBELL0;`
ARM VPU Halted
`BCM2838_IRQ_ARM_VPU0HALTED = BCM2838_SPI_BASE + 36;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_VPU1HALTED = BCM2838_SPI_BASE + 37;`	IRQ_TYPE_LEVEL_HIGH
ARM Error
`BCM2838_IRQ_ARM_ADDRERROR = BCM2838_SPI_BASE + 38;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_AXIERROR = BCM2838_SPI_BASE + 39;`	IRQ_TYPE_LEVEL_HIGH
ARM Software Interrupt (SWI)
`BCM2838_IRQ_ARM_SWI0 = BCM2838_SPI_BASE + 40;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI1 = BCM2838_SPI_BASE + 41;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI2 = BCM2838_SPI_BASE + 42;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI3 = BCM2838_SPI_BASE + 43;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI4 = BCM2838_SPI_BASE + 44;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI5 = BCM2838_SPI_BASE + 45;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI6 = BCM2838_SPI_BASE + 46;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_ARM_SWI7 = BCM2838_SPI_BASE + 47;`	IRQ_TYPE_LEVEL_HIGH
VC peripheral IRQs (BCM2838_SPI_BASE + 64 to 127)
System Timer
`BCM2838_IRQ_SYSTEM_TIMER_0 = BCM2838_SPI_BASE + 64;`	Already used by the VideoCore GPU (Do not use)
`BCM2838_IRQ_SYSTEM_TIMER_1 = BCM2838_SPI_BASE + 65;`
`BCM2838_IRQ_SYSTEM_TIMER_2 = BCM2838_SPI_BASE + 66;`	Already used by the VideoCore GPU (Do not use)
`BCM2838_IRQ_SYSTEM_TIMER_3 = BCM2838_SPI_BASE + 67;`
H264 Codec
`BCM2838_IRQ_H264_0 = BCM2838_SPI_BASE + 68;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_H264_1 = BCM2838_SPI_BASE + 69;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_H264_2 = BCM2838_SPI_BASE + 70;`	IRQ_TYPE_LEVEL_HIGH
JPEG
`BCM2838_IRQ_JPEG = BCM2838_SPI_BASE + 71;`	IRQ_TYPE_LEVEL_HIGH
ISP
`BCM2838_IRQ_ISP = BCM2838_SPI_BASE + 72;`	IRQ_TYPE_LEVEL_HIGH
USB (Synopsys DesignWare Hi-Speed USB 2.0 On-The-Go Controller)
`BCM2838_IRQ_USB = BCM2838_SPI_BASE + 73;`	IRQ_TYPE_LEVEL_HIGH
V3D
`BCM2838_IRQ_V3D = BCM2838_SPI_BASE + 74;`	IRQ_TYPE_LEVEL_HIGH
Transposer
`BCM2838_IRQ_TXP = BCM2838_SPI_BASE + 75;`	IRQ_TYPE_LEVEL_HIGH
Multicore Sync
`BCM2838_IRQ_MULTICORESYNC0 = BCM2838_SPI_BASE + 76;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MULTICORESYNC1 = BCM2838_SPI_BASE + 77;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MULTICORESYNC2 = BCM2838_SPI_BASE + 78;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_MULTICORESYNC3 = BCM2838_SPI_BASE + 79;`	IRQ_TYPE_LEVEL_HIGH
DMA
`BCM2838_IRQ_DMA0 = BCM2838_SPI_BASE + 80;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA1 = BCM2838_SPI_BASE + 81;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA2 = BCM2838_SPI_BASE + 82;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA3 = BCM2838_SPI_BASE + 83;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA4 = BCM2838_SPI_BASE + 84;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA5 = BCM2838_SPI_BASE + 85;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA6 = BCM2838_SPI_BASE + 86;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA7 = BCM2838_SPI_BASE + 87;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA8 = BCM2838_SPI_BASE + 87;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA9 = BCM2838_SPI_BASE + 88;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA10 = BCM2838_SPI_BASE + 88;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA11 = BCM2838_SPI_BASE + 89;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA12 = BCM2838_SPI_BASE + 90;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA13 = BCM2838_SPI_BASE + 91;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_DMA14 = BCM2838_SPI_BASE + 92;`	IRQ_TYPE_LEVEL_HIGH

`BCM2838_IRQ_DMA7_8 = BCM2838_IRQ_DMA7;`
`BCM2838_IRQ_DMA9_10 = BCM2838_IRQ_DMA9;`
AUX (UART1, SPI1 and SPI2)
`BCM2838_IRQ_AUX = BCM2838_SPI_BASE + 93;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_UART1 = BCM2838_IRQ_AUX;`
`BCM2838_IRQ_SPI1 = BCM2838_IRQ_AUX;`
`BCM2838_IRQ_SPI2 = BCM2838_IRQ_AUX;`
ARM
`BCM2838_IRQ_ARM = BCM2838_SPI_BASE + 94;`	IRQ_TYPE_LEVEL_HIGH
DMA Note: DMA15 is exclusively used by the VPU
`BCM2838_IRQ_DMA15 = BCM2838_SPI_BASE + 95;`	IRQ_TYPE_LEVEL_HIGH
HDMI CEC
`BCM2838_IRQ_HDMI_CEC = BCM2838_SPI_BASE + 96;`	IRQ_TYPE_LEVEL_HIGH
HVS
`BCM2838_IRQ_HVS = BCM2838_SPI_BASE + 97;`	IRQ_TYPE_LEVEL_HIGH
ARGON (RPIVID)
`BCM2838_IRQ_ARGON = BCM2838_SPI_BASE + 98;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_RPIVID = BCM2838_IRQ_ARGON;`
SDC
`BCM2838_IRQ_SDC = BCM2838_SPI_BASE + 99;`	IRQ_TYPE_LEVEL_HIGH
DSI0
`BCM2838_IRQ_DSI0 = BCM2838_SPI_BASE + 100;`	IRQ_TYPE_LEVEL_HIGH
Pixel Valve 2
`BCM2838_IRQ_PIXELVALVE2 = BCM2838_SPI_BASE + 101;`	IRQ_TYPE_LEVEL_HIGH
CSI0 (Camera Serial Interface)
`BCM2838_IRQ_CSI0 = BCM2838_SPI_BASE + 102;`	IRQ_TYPE_LEVEL_HIGH
CSI1 (Camera Serial Interface)
`BCM2838_IRQ_CSI1 = BCM2838_SPI_BASE + 103;`	IRQ_TYPE_LEVEL_HIGH
HDMI
`BCM2838_IRQ_HDMI_0 = BCM2838_SPI_BASE + 104;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_HDMI_1 = BCM2838_SPI_BASE + 105;`	IRQ_TYPE_LEVEL_HIGH
Pixel Valve 3
`BCM2838_IRQ_PIXELVALVE3 = BCM2838_SPI_BASE + 106;`	IRQ_TYPE_LEVEL_HIGH
I2C / SPI Slave
`BCM2838_IRQ_I2CSPI = BCM2838_SPI_BASE + 107;`	IRQ_TYPE_LEVEL_HIGH
DSI1
`BCM2838_IRQ_DSI1 = BCM2838_SPI_BASE + 108;`	IRQ_TYPE_LEVEL_HIGH
Pixel Valve 0
`BCM2838_IRQ_PIXELVALVE0 = BCM2838_SPI_BASE + 109;`	IRQ_TYPE_LEVEL_HIGH
Pixel Valve 1/4
`BCM2838_IRQ_PIXELVALVE1 = BCM2838_SPI_BASE + 110;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PIXELVALVE4 = BCM2838_IRQ_PIXELVALVE1;`
CPR
`BCM2838_IRQ_CPR = BCM2838_SPI_BASE + 111;`	IRQ_TYPE_LEVEL_HIGH
SMI (Firmware KMS)
`BCM2838_IRQ_SMI = BCM2838_SPI_BASE + 112;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_FIRMWAREKMS = BCM2838_IRQ_SMI;`
GPIO
`BCM2838_IRQ_GPIO_0 = BCM2838_SPI_BASE + 113;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_GPIO_1 = BCM2838_SPI_BASE + 114;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_GPIO_2 = BCM2838_SPI_BASE + 115;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_GPIO_3 = BCM2838_SPI_BASE + 116;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_GPIO_ALL = BCM2838_IRQ_GPIO_3;`
BSC0 (I2C0) (Broadcom Serial Controller)
`BCM2838_IRQ_BSC0 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_I2C0 = BCM2838_IRQ_BSC0;`
BSC1 (I2C1) (Broadcom Serial Controller)
`BCM2838_IRQ_BSC1 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_I2C1 = BCM2838_IRQ_BSC1;`
BSC2 (I2C2) (Broadcom Serial Controller)
`BCM2838_IRQ_BSC2 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_I2C2 = BCM2838_IRQ_BSC2;`
I2C3
`BCM2838_IRQ_I2C3 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
I2C4
`BCM2838_IRQ_I2C4 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
I2C5
`BCM2838_IRQ_I2C5 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
I2C6
`BCM2838_IRQ_I2C6 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
I2C7
`BCM2838_IRQ_I2C7 = BCM2838_SPI_BASE + 117;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_I2C0_IRQS:array[0..7] of LongWord = (BCM2838_IRQ_I2C0, BCM2838_IRQ_I2C1, BCM2838_IRQ_I2C2, BCM2838_IRQ_I2C3, BCM2838_IRQ_I2C4, BCM2838_IRQ_I2C5, BCM2838_IRQ_I2C6, BCM2838_IRQ_I2C7);`
SPI0
`BCM2838_IRQ_SPI0 = BCM2838_SPI_BASE + 118;`	IRQ_TYPE_LEVEL_HIGH
SPI3
`BCM2838_IRQ_SPI3 = BCM2838_SPI_BASE + 118;`	IRQ_TYPE_LEVEL_HIGH
SPI4
`BCM2838_IRQ_SPI4 = BCM2838_SPI_BASE + 118;`	IRQ_TYPE_LEVEL_HIGH
SPI5
`BCM2838_IRQ_SPI5 = BCM2838_SPI_BASE + 118;`	IRQ_TYPE_LEVEL_HIGH
SPI6
`BCM2838_IRQ_SPI6 = BCM2838_SPI_BASE + 118;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_SPI0_IRQS:array[0..6] of LongWord = (BCM2838_IRQ_SPI0, 0, 0, BCM2838_IRQ_SPI3, BCM2838_IRQ_SPI4, BCM2838_IRQ_SPI5, BCM2838_IRQ_SPI6);`
I2S PCM sound
`BCM2838_IRQ_I2SPCM = BCM2838_SPI_BASE + 119;`	IRQ_TYPE_LEVEL_HIGH
EMMC1 (SDHOST)
`BCM2838_IRQ_EMMC1 = BCM2838_SPI_BASE + 120;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_SDHOST = BCM2838_IRQ_EMMC1;`
UART0 (PL011)
`BCM2838_IRQ_PL011 = BCM2838_SPI_BASE + 121;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_UART0 = BCM2838_IRQ_PL011;`
UART2 (PL011)
`BCM2838_IRQ_UART2 = BCM2838_SPI_BASE + 121;`	IRQ_TYPE_LEVEL_HIGH
UART3 (PL011)
`BCM2838_IRQ_UART3 = BCM2838_SPI_BASE + 121;`	IRQ_TYPE_LEVEL_HIGH
UART4 (PL011)
`BCM2838_IRQ_UART4 = BCM2838_SPI_BASE + 121;`	IRQ_TYPE_LEVEL_HIGH
UART5 (PL011)
`BCM2838_IRQ_UART5 = BCM2838_SPI_BASE + 121;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_UART0_IRQS:array[0..5] of LongWord = (BCM2838_IRQ_UART0, 0, BCM2838_IRQ_UART2, BCM2838_IRQ_UART3, BCM2838_IRQ_UART4, BCM2838_IRQ_UART5);`
ETH_PCIe L2
`BCM2838_IRQ_ETH_PCIE = BCM2838_SPI_BASE + 122;`	IRQ_TYPE_LEVEL_HIGH
VEC
`BCM2838_IRQ_VEC = BCM2838_SPI_BASE + 123;`	IRQ_TYPE_LEVEL_HIGH
CPG
`BCM2838_IRQ_CPG = BCM2838_SPI_BASE + 124;`	IRQ_TYPE_LEVEL_HIGH
Random Number Generator
`BCM2838_IRQ_RNG = BCM2838_SPI_BASE + 125;`	IRQ_TYPE_LEVEL_HIGH
EMMC0 (SDHCI)
`BCM2838_IRQ_EMMC0 = BCM2838_SPI_BASE + 126;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_SDHCI = BCM2838_IRQ_EMMC0;`
EMMC2 (SDHCI)
`BCM2838_IRQ_EMMC2 = BCM2838_SPI_BASE + 126;`	IRQ_TYPE_LEVEL_HIGH
ETH_PCIe Secure
`BCM2838_IRQ_ETH_PCIE_SEC = BCM2838_SPI_BASE + 127;`	IRQ_TYPE_LEVEL_HIGH
ETH_PCIe L2 IRQs (BCM2838_SPI_BASE + 128 to 184)
Thermal (AVS)
`BCM2838_IRQ_THERMAL = BCM2838_SPI_BASE + 137;`	IRQ_TYPE_LEVEL_HIGH
PCIe
`BCM2838_IRQ_PCIE_INTA = BCM2838_SPI_BASE + 143;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PCIE_INTB = BCM2838_SPI_BASE + 144;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PCIE_INTC = BCM2838_SPI_BASE + 145;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PCIE_INTD = BCM2838_SPI_BASE + 146;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_PCIE_MSI = BCM2838_SPI_BASE + 148;`	IRQ_TYPE_LEVEL_HIGH
GENET
`BCM2838_IRQ_GENET_0 = BCM2838_SPI_BASE + 157;`	IRQ_TYPE_LEVEL_HIGH
`BCM2838_IRQ_GENET_1 = BCM2838_SPI_BASE + 158;`	IRQ_TYPE_LEVEL_HIGH
XHCI (Additional on chip generic XHCI USB host controller)
`BCM2838_IRQ_XHCI = BCM2838_SPI_BASE + 176;`	IRQ_TYPE_LEVEL_HIGH (This is separate to the VL805 XHCI controller)
Number of shared IRQs
`BCM2838_SHARED_IRQ_COUNT = 988;`	SPI 32-1019
Number of private IRQs
`BCM2838_PRIVATE_IRQ_COUNT = 16;`	PPI 16-31
Number of software IRQs
`BCM2838_SOFTWARE_IRQ_COUNT = 16;`	SGI 0-15
Number of reserved IRQs
`BCM2838_RESERVED_IRQ_COUNT = 4;`	ID 1020-1023
Total number of IRQs available
`BCM2838_IRQ_COUNT = BCM2838_SHARED_IRQ_COUNT + BCM2838_PRIVATE_IRQ_COUNT + BCM2838_SOFTWARE_IRQ_COUNT + BCM2838_RESERVED_IRQ_COUNT;`
Total number of FIQs available
`BCM2838_FIQ_COUNT = BCM2838_IRQ_COUNT;`

BCM2838 system timer frequency BCM2838_SYSTEM_TIMER_BCM2838_SYSTEM_TIMER_FREQUENCY*

`BCM2838_SYSTEM_TIMER_FREQUENCY = 1000000;`	Default clock frequency of the BCM2838 System Timer (1MHz)

BCM2838 system timer control/status BCM2838_SYSTEM_TIMER_CS_*

See: Section 12

`BCM2838_SYSTEM_TIMER_CS_0 = (1 shl 0);`	Already used by the VideoCore GPU (Do not use)
`BCM2838_SYSTEM_TIMER_CS_1 = (1 shl 1);`
`BCM2838_SYSTEM_TIMER_CS_2 = (1 shl 2);`	Already used by the VideoCore GPU (Do not use)
`BCM2838_SYSTEM_TIMER_CS_3 = (1 shl 3);`

BCM2838 DMA control/status BCM2838_DMA_CS_*

See: Section 4

`BCM2838_DMA_CS_ACTIVE = (1 shl 0);`	Activate the DMA (This bit enables the DMA. The DMA will start if this bit is set and the CB_ADDR is non zero. The DMA transfer can be paused and resumed by clearing, then setting it again.)
`BCM2838_DMA_CS_END = (1 shl 1);`	DMA End Flag (Set when the transfer described by the current control block is complete. Write 1 to clear.)
`BCM2838_DMA_CS_INT = (1 shl 2);`	Interrupt Status (This is set when the transfer for the CB ends and INTEN is set to 1. Write 1 to clear.)
`BCM2838_DMA_CS_DREQ = (1 shl 3);`	DREQ State (Indicates the state of the selected DREQ (Data Request) signal, ie. the DREQ selected by the PERMAP field of the transfer info.)
`BCM2838_DMA_CS_PAUSED = (1 shl 4);`	DMA Paused State (Indicates if the DMA is currently paused and not transferring data)
`BCM2838_DMA_CS_DREQ_PAUSED = (1 shl 5);`	DMA Paused by DREQ State (Indicates if the DMA is currently paused and not transferring data due to the DREQ being inactive)
`BCM2838_DMA_CS_WAITING_FOR_OUTSTANDING_WRITES = (1 shl 6);`	DMA is Waiting for the Last Write to be Received (Indicates if the DMA is currently waiting for any outstanding writes to be received, and is not transferring data.)
Bit 7 Reserved - Write as 0, read as don't care
`BCM2838_DMA_CS_ERROR = (1 shl 8);`	DMA Error (Indicates if the DMA has detected an error)
`BCM2838_DMA_CS_PRIORITY = ($F shl 16);`	AXI Priority Level (Sets the priority of normal AXI bus transactions. Zero is the lowest priority.)
`BCM2838_DMA_CS_PANIC_PRIORITY = ($F shl 20);`	AXI Panic Priority Level (Sets the priority of panicking AXI bus transactions)
Bits 24:27 Reserved - Write as 0, read as don't care
`BCM2838_DMA_CS_WAIT_FOR_OUTSTANDING_WRITES = (1 shl 28);`	Wait for outstanding writes (When set to 1, the DMA will keep a tally of the AXI writes going out and the write responses coming in.)
`BCM2838_DMA_CS_DISDEBUG = (1 shl 29);`	Disable debug pause signal (When set to 1, the DMA will not stop when the debug pause signal is asserted.)
`BCM2838_DMA_CS_ABORT = (1 shl 30);`	Abort DMA (Writing a 1 to this bit will abort the current DMA CB. The DMA will load the next CB and attempt to continue. The bit cannot be read, and will self clear.)
`BCM2838_DMA_CS_RESET = (1 shl 31);`	DMA Channel Reset (Writing a 1 to this bit will reset the DMA. The bit cannot be read, and will self clear.)

`BCM2838_DMA_CS_PRIORITY_DEFAULT = 0;`

BCM2838 DMA transfer information BCM2838_DMA_TI_*

See: Section 4

`BCM2838_DMA_TI_INTEN = (1 shl 0);`	Interrupt Enable (1 = Generate an interrupt when the transfer described by the current Control Block completes)
`BCM2838_DMA_TI_2DMODE = (1 shl 1);`	2D Mode (1 = 2D mode interpret the TXFR_LEN register as YLENGTH number of transfers each of XLENGTH, and add the strides to the address after each transfer.)
Bit 2 Reserved - Write as 0, read as don't care
`BCM2838_DMA_TI_WAIT_RESP = (1 shl 3);`	Wait for a Write Response (When set this makes the DMA wait until it receives the AXI write response for each write. This ensures that multiple writes cannot get stacked in the AXI bus pipeline.)
`BCM2838_DMA_TI_DEST_INC = (1 shl 4);`	Destination Address Increment (1 = Destination address increments after each write. The address will increment by 4, if DEST_WIDTH=0 else by 32.)
`BCM2838_DMA_TI_DEST_WIDTH = (1 shl 5);`	Destination Transfer Width (1 = Use 128-bit destination write width. 0 = Use 32-bit destination write width.)
`BCM2838_DMA_TI_DEST_DREQ = (1 shl 6);`	Control Destination Writes with DREQ (1 = The DREQ selected by PERMAP will gate the destination writes)
`BCM2838_DMA_TI_DEST_IGNORE = (1 shl 7);`	Ignore Writes (1 = Do not perform destination writes. 0 = Write data to destination.)
`BCM2838_DMA_TI_SRC_INC = (1 shl 8);`	Source Address Increment (1 = Source address increments after each read. The address will increment by 4, if S_WIDTH=0 else by 32.)
`BCM2838_DMA_TI_SRC_WIDTH = (1 shl 9);`	Source Transfer Width (1 = Use 128-bit source read width. 0 = Use 32-bit source read width.)
`BCM2838_DMA_TI_SRC_DREQ = (1 shl 10);`	Control Source Reads with DREQ (1 = The DREQ selected by PERMAP will gate the source reads)
`BCM2838_DMA_TI_SRC_IGNORE = (1 shl 11);`	Ignore Reads (1 = Do not perform source reads. In addition, destination writes will zero all the write strobes. This is used for fast cache fill operations.)
`BCM2838_DMA_TI_BURST_LENGTH = ($F shl 12);`	Burst Transfer Length (Indicates the burst length of the DMA transfers)
`BCM2838_DMA_TI_PERMAP = ($1F shl 16);`	Peripheral Mapping (Indicates the peripheral number (1-31) whose ready signal shall be used to control the rate of the transfers)
`BCM2838_DMA_TI_WAITS = ($3E shl 21);`	Add Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles burnt after each DMA read or write operation is completed)
`BCM2838_DMA_TI_NO_WIDE_BURSTS = (1 shl 26);`	Don't Do wide writes as a 2 beat burst (This prevents the DMA from issuing wide writes as 2 beat AXI bursts. This is an inefficient access mode, so the default is to use the bursts.)
Bits 27:31 Reserved - Write as 0, read as don't care

Note: BCM2838_DMA_TI_2DMODE, BCM2838_DMA_TI_DEST_IGNORE, BCM2838_DMA_TI_SRC_IGNORE and BCM2838_DMA_TI_NO_WIDE_BURSTS not available on DMA Lite channels

`BCM2838_DMA_TI_PERMAP_SHIFT = 16;`
`BCM2838_DMA_TI_BURST_LENGTH_SHIFT = 12;`

`BCM2838_DMA_TI_BURST_LENGTH_DEFAULT = 0;`

BCM2838 DMA transfer length BCM2838_DMA_TXFR_LEN_*

See: Section 4

`BCM2838_DMA_TXFR_LEN_XLENGTH = ($FFFF shl 0);`	Transfer Length in bytes
`BCM2838_DMA_TXFR_LEN_YLENGTH = ($3FFF shl 16);`	When in 2D mode, This is the Y transfer length, indicating how many xlength transfers are performed. When in normal linear mode this becomes the top bits of the XLENGTH.

Note: BCM2838_DMA_TXFR_LEN_YLENGTH not available on DMA Lite channels

BCM2838 DMA 2D stride BCM2838_DMA_STRIDE_*

See: Section 4

`BCM2838_DMA_STRIDE_S_STRIDE = ($FFFF shl 0);`	Destination Stride (2D Mode) (Signed (2 s complement) byte increment to apply to the destination address at the end of each row in 2D mode)
`BCM2838_DMA_STRIDE_D_STRIDE = ($FFFF shl 16);`	Source Stride (2D Mode) (Signed (2 s complement) byte increment to apply to the source address at the end of each row in 2D mode)

Note: BCM2838_DMA_STRIDE_S_STRIDE and BCM2838_DMA_STRIDE_D_STRIDE not available on DMA Lite channels

BCM2838 DMA debug BCM2838_DMA_DEBUG_*

See: Section 4

`BCM2838_DMA_DEBUG_READ_LAST_NOT_SET_ERROR = (1 shl 0);`	Read Last Not Set Error
`BCM2838_DMA_DEBUG_FIFO_ERROR = (1 shl 1);`	Fifo Error
`BCM2838_DMA_DEBUG_READ_ERROR = (1 shl 2);`	Slave Read Response Error
Bit 3 Reserved - Write as 0, read as don't care
`BCM2838_DMA_DEBUG_OUTSTANDING_WRITES = ($F shl 4);`	DMA Outstanding Writes Counter
`BCM2838_DMA_DEBUG_DMA_ID = ($FF shl 8);`	DMA ID
`BCM2838_DMA_DEBUG_DMA_STATE = ($1FF shl 16);`	DMA State Machine State
`BCM2838_DMA_DEBUG_VERSION = (7 shl 25);`	DMA Version
`BCM2838_DMA_DEBUG_LITE = (1 shl 28);`	DMA Lite
Bits 29:31 Reserved - Write as 0, read as don't care

BCM2838 DMA4 control/status BCM2838_DMA4_CS_*

See: Section 4

`BCM2838_DMA4_CS_ACTIVE = (1 shl 0);`	Activate the DMA4 (This bit enables the DMA4 to start transferring data)
`BCM2838_DMA4_CS_END = (1 shl 1);`	End Flag (Set when the transfer described by the current Control Block is complete)
`BCM2838_DMA4_CS_INT = (1 shl 2);`	Interrupt Status (If interrupts are enabled (INTEN is set to 1) the interrupt is set when the transfer for the current CB is completed)
`BCM2838_DMA4_CS_DREQ = (1 shl 3);`	DREQ State (Indicates the state of the selected DREQ (Data Request) signal)
`BCM2838_DMA4_CS_RD_PAUSED = (1 shl 4);`	DMA read Paused State (Indicates that the DMA4 is currently paused and not reading data)
`BCM2838_DMA4_CS_WR_PAUSED = (1 shl 5);`	DMA Write Paused State (Indicates that the DMA4 is currently paused and not writing data)
`BCM2838_DMA4_CS_DREQ_STOPS_DMA = (1 shl 6);`	DMA Paused by DREQ State (This indicates that the DMA4 is currently paused and not transferring data due to the selected DREQ being inactive)
`BCM2838_DMA4_CS_WAITING_FOR_OUTSTANDING_WRITES = (1 shl 7);`	The DMA4 is Waiting for all the Write Response to be returned
Bits 8:9 Reserved
`BCM2838_DMA4_CS_ERROR = (1 shl 10);`	DMA Error (Indicates if the DMA4 has detected an error)
Bits 11:15 Reserved
`BCM2838_DMA4_CS_QOS_MASK = ($F shl 16);`	AXI QOS Level (Sets the QOS level of normal AXI bus transactions)
`BCM2838_DMA4_CS_QOS_DEFAULT = (0 shl 16);`
`BCM2838_DMA4_CS_PANIC_QOS_MASK = ($F shl 20);`	AXI Panic QOS Level (Sets the QOS level of AXI bus transactions when the DMA4 is panicking)
`BCM2838_DMA4_CS_PANIC_QOS_DEFAULT = (0 shl 20);`
`BCM2838_DMA4_CS_DMA_BUSY = (1 shl 24);`	Indicates the DMA4 is BUSY (This indicates that the DMA4 is operating or waiting for outstanding data or otherwise in use)
`BCM2838_DMA4_CS_OUTSTANDING_TRANSACTIONS = (1 shl 25);`	Indicates that there are outstanding AXI transfers, either outstanding read data or outstanding write responses.
Bits 26:27 Reserved
`BCM2838_DMA4_CS_WAIT_FOR_OUTSTANDING_WRITES = (1 shl 28);`	Wait for outstanding writes (The DMA4 keeps a tally of the AXI writes requests going out and the write responses coming in)
`BCM2838_DMA4_CS_DISDEBUG = (1 shl 29);`	Disable Debug Pause Signal (When set to 1, the DMA4 will not pause when the debug pause signal is asserted.)
`BCM2838_DMA4_CS_ABORT = (1 shl 30);`	Abort DMA (Writing a 1 to this bit will cleanly abort the current DMA transfer. The abort will cause the DMA4 to zero its length counters and thus it will complete the current transfer and wait until all outstanding bus activity has finished)
`BCM2838_DMA4_CS_HALT = (1 shl 31);`	Halt DMA (Writing a 1 to this bit will cleanly halt the current DMA transfer. The halt will cause the DMA4 to zero its length counters and thus it will complete the current transfer and wait until all outstanding bus activity has finished.)

BCM2838 DMA4 control block address BCM2838_DMA4_CB_*

See: Section 4

`BCM2838_DMA4_CB_ADDR_MASK = $0000001FFFFFFFE0;`
`BCM2838_DMA4_CB_ADDR_SHIFT = 5;`	Write Address shr 5 to the register

BCM2838 DMA4 debug register BCM2838_DMA4_DEBUG_*

See: Section 4

`BCM2838_DMA4_DEBUG_WRITE_ERROR = (1 shl 0);`	Slave Write Response Error
`BCM2838_DMA4_DEBUG_FIFO_ERROR = (1 shl 1);`	FIFO Error
`BCM2838_DMA4_DEBUG_READ_ERROR = (1 shl 2);`	Slave Read Response Error
`BCM2838_DMA4_DEBUG_READ_CB_ERROR = (1 shl 3);`	Slave Read Response Error During Control Block Read
Bits 4:7 Reserved
`BCM2838_DMA4_DEBUG_INT_ON_ERROR = (1 shl 8);`	Generate an interrupt if an error is detected
`BCM2838_DMA4_DEBUG_HALT_ON_ERROR = (1 shl 9);`	Instruct the DMA4 to HALT if it detects an error
`BCM2838_DMA4_DEBUG_ABORT_ON_ERROR = (1 shl 10);`	Instruct the DMA4 to ABORT if it detects an error
`BCM2838_DMA4_DEBUG_DISABLE_CLK_GATE = (1 shl 11);`	Disable the clock gating logic
Bits 12:13 Reserved
`BCM2838_DMA4_DEBUG_R_STATE_MASK = ($F shl 14);`	Read State Machine State (Returns the value of the DMA4 engines read state machine)
`BCM2838_DMA4_DEBUG_R_IDLE = (0 shl 14);`
`BCM2838_DMA4_DEBUG_R_WAIT_CB_DATA = (1 shl 14);`
`BCM2838_DMA4_DEBUG_R_CALC = (2 shl 14);`
`BCM2838_DMA4_DEBUG_R_READ4K = (3 shl 14);`
`BCM2838_DMA4_DEBUG_R_READING = (4 shl 14);`
`BCM2838_DMA4_DEBUG_R_READFIFO_FULL = (5 shl 14);`
`BCM2838_DMA4_DEBUG_R_WAIT_WRITE_COMPLETE = (6 shl 14);`
`BCM2838_DMA4_DEBUG_W_STATE_MASK = ($F shl 18);`	Write State Machine State (Returns the value of the DMA4 engines write state machine)
`BCM2838_DMA4_DEBUG_W_IDLE = (0 shl 18);`
`BCM2838_DMA4_DEBUG_W_PRELOAD = (1 shl 18);`
`BCM2838_DMA4_DEBUG_W_CALC = (2 shl 18);`
`BCM2838_DMA4_DEBUG_W_WRITE4K = (3 shl 18);`
`BCM2838_DMA4_DEBUG_W_READFIFO_EMPTY = (4 shl 18);`
`BCM2838_DMA4_DEBUG_W_WAIT_OUTSTANDING = (5 shl 18);`
Bit 22 Reserved
`BCM2838_DMA4_DEBUG_RESET = (1 shl 23);`	DMA Reset (This is a hard reset of the DMA4 state machine and certain internal registers)
`BCM2838_DMA4_DEBUG_ID_MASK = ($F shl 24);`	ID (Returns the ID of this DMA4. This is also used as the AXI subid.)
`BCM2838_DMA4_DEBUG_VERSION_MASK = ($F shl 28);`	DMA Version (DMA version number, indicating control bit field changes.)

BCM2838 DMA4 transfer information BCM2838_DMA4_TI_*

See: Section 4

`BCM2838_DMA4_TI_INTEN = (1 shl 0);`	Interrupt Enable
`BCM2838_DMA4_TI_TDMODE = (1 shl 1);`	2D Mode (Perform a 2D transfer instead of a normal linear transfer. In 2D mode the DMA4 will interpret the length field as an X and a Y length. It will execute Y+1 transfers each of length X.)
`BCM2838_DMA4_TI_WAIT_RESP = (1 shl 2);`	Wait for a Write Response (When set this makes the DMA4 wait until it receives the AXI write response for each write)
`BCM2838_DMA4_TI_WAIT_RD_RESP = (1 shl 3);`	Wait for a Read Response (When set this makes the DMA4 wait until it receives all the data from each read)
Bits 4:8 Reserved
`BCM2838_DMA4_TI_PERMAP_MASK = ($1F shl 9);`	Peripheral Mapping (Indicates the DREQ of selected peripheral (1-31))
`BCM2838_DMA4_TI_PERMAP_SHIFT = 9;`
`BCM2838_DMA4_TI_S_DREQ = (1 shl 14);`	Control Source Reads with DREQ (This is used when reading from a peripheral that has a DREQ flow control available)
`BCM2838_DMA4_TI_D_DREQ = (1 shl 15);`	Control Destination Writes with DREQ (This is used when writing to a peripheral that has a DREQ flow control available to control the data flow)
`BCM2838_DMA4_TI_S_WAITS_MASK = ($FF shl 16);`	Read Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles burnt before each DMA AXI read operation is started)
`BCM2838_DMA4_TI_S_WAITS_DEFAULT = (0 shl 16);`
`BCM2838_DMA4_TI_D_WAITS_MASK = ($FF shl 24);`	Write Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles before each AXI Write operation is started)
`BCM2838_DMA4_TI_D_WAITS_DEFAULT = (0 shl 24);`

BCM2838 DMA4 source address BCM2838_DMA4_SRC_ADDR_*

See: Section 4

`BCM2838_DMA4_SRC_ADDR_MASK = $00000000FFFFFFFF;`

BCM2838 DMA4 source information BCM2838_DMA4_SRCI_*

See: Section 4

`BCM2838_DMA4_SRCI_ADDR_MASK = ($FF shl 0);`	High Bits of the Source Address [40:32]
`BCM2838_DMA4_SRCI_BURST_LENGTH_MASK = ($F shl 8);`	Burst Transfer Length
`BCM2838_DMA4_SRCI_BURST_LENGTH_SHIFT = 8;`
`BCM2838_DMA4_SRCI_BURST_LENGTH_DEFAULT = (0 shl 8);`
`BCM2838_DMA4_SRCI_INC = (1 shl 12);`	Increment the Source Address
`BCM2838_DMA4_SRCI_SIZE_MASK = (3 shl 13);`	Source Transfer Width (The DMA4 will perform all AXI source reads with this AXI transfer width)
`BCM2838_DMA4_SRCI_SIZE_256 = (3 shl 13);`	Note: On the BCM2711 the width cannot be set larger than 128
`BCM2838_DMA4_SRCI_SIZE_128 = (2 shl 13);`
`BCM2838_DMA4_SRCI_SIZE_64 = (1 shl 13);`
`BCM2838_DMA4_SRCI_SIZE_32 = (0 shl 13);`
`BCM2838_DMA4_SRCI_IGNORE = (1 shl 15);`	Ignore Reads (The DMA4 will perform a normal transfer except that it will not produce any reads. The DMA4 will write zero data.)
`BCM2838_DMA4_SRCI_STRIDE = ($FFFF shl 16);`	Source Stride (This is only used in 2D transfer mode (TDMODE))

BCM2838 DMA4 dest address BCM2838_DMA4_DEST_ADDR_*

See: Section 4

`BCM2838_DMA4_DEST_ADDR_MASK = $00000000FFFFFFFF;`

BCM2838 DMA4 dest information BCM2838_DMA4_DESTI_*

See: Section 4

`BCM2838_DMA4_DESTI_ADDR_MASK = ($FF shl 0);`	High Bits of the Destination Address [40:32]
`BCM2838_DMA4_DESTI_BURST_LENGTH_MASK = ($F shl 8);`	Burst Transfer Length
`BCM2838_DMA4_DESTI_BURST_LENGTH_SHIFT = 8;`
`BCM2838_DMA4_DESTI_BURST_LENGTH_DEFAULT = (0 shl 8);`
`BCM2838_DMA4_DESTI_INC = (1 shl 12);`	Destination Address Increment
`BCM2838_DMA4_DESTI_SIZE_MASK = (3 shl 13);`	Destination Transfer Width (The DMA4 will perform all AXI destination writes with this AXI transfer width)
`BCM2838_DMA4_DESTI_SIZE_256 = (3 shl 13);`	Note: On the BCM2711 the width cannot be set larger than 128
`BCM2838_DMA4_DESTI_SIZE_128 = (2 shl 13);`
`BCM2838_DMA4_DESTI_SIZE_64 = (1 shl 13);`
`BCM2838_DMA4_DESTI_SIZE_32 = (0 shl 13);`
`BCM2838_DMA4_DESTI_IGNORE = (1 shl 15);`	Ignore Destination Writes
`BCM2838_DMA4_DESTI_STRIDE = ($FFFF shl 16);`	Destination Stride (This is only used in 2D transfer mode (TDMODE))

BCM2838 DMA4 transfer length BCM2838_DMA4_LEN_*

See: Section 4

`BCM2838_DMA4_LEN_XLENGTH_MASK = ($FFFF shl 0);`	Transfer Length in bytes
`BCM2838_DMA4_LEN_YLENGTH_MASK = ($3FFF shl 16);`	When in 2D mode, This is the Y transfer length, indicating how many xlength transfers are performed. When in normal linear mode this becomes the top bits of the XLENGTH.
Bits 30:31 Reserved

BCM2838 DMA4 next control block address BCM2838_DMA4_NEXT_CB_ *

See: Section 4

`BCM2838_DMA4_NEXT_CB_ADDR_MASK = $0000001FFFFFFFE0;`
`BCM2838_DMA4_NEXT_CB_ADDR_SHIFT = 5;`	Write Address shr 5 to the register

BCM2838 DMA4 Debug BCM2838_DMA4_DEBUG2_*

See: Section 4

`BCM2838_DMA4_DEBUG2_OUTSTANDING_WRITES_MASK = ($1FF shl 0);`	Outstanding Write Response Count
Bits 9:15 Reserved
`BCM2838_DMA4_DEBUG2_OUTSTANDING_READS_MASK = ($1FF shl 16);`	Outstanding read Words Count
Bits 25:31 Reserved

BCM2838 DMA engine interrupt status BCM2838_DMA_INT_*

See: Section 4

`BCM2838_DMA_INT_STATUS_0 = (1 shl 0);`
`BCM2838_DMA_INT_STATUS_1 = (1 shl 1);`
`BCM2838_DMA_INT_STATUS_2 = (1 shl 2);`
`BCM2838_DMA_INT_STATUS_3 = (1 shl 3);`
`BCM2838_DMA_INT_STATUS_4 = (1 shl 4);`
`BCM2838_DMA_INT_STATUS_5 = (1 shl 5);`
`BCM2838_DMA_INT_STATUS_6 = (1 shl 6);`
`BCM2838_DMA_INT_STATUS_7 = (1 shl 7);`
`BCM2838_DMA_INT_STATUS_8 = (1 shl 8);`
`BCM2838_DMA_INT_STATUS_9 = (1 shl 9);`
`BCM2838_DMA_INT_STATUS_10 = (1 shl 10);`
`BCM2838_DMA_INT_STATUS_11 = (1 shl 11);`
`BCM2838_DMA_INT_STATUS_12 = (1 shl 12);`
`BCM2838_DMA_INT_STATUS_13 = (1 shl 13);`
`BCM2838_DMA_INT_STATUS_14 = (1 shl 14);`
`BCM2838_DMA_INT_STATUS_15 = (1 shl 15);`
Bits 16:31 Reserved

BCM2838 DMA engine enable BCM2838_DMA_ENABLE_*

See: Section 4

`BCM2838_DMA_ENABLE_0 = (1 shl 0);`
`BCM2838_DMA_ENABLE_1 = (1 shl 1);`
`BCM2838_DMA_ENABLE_2 = (1 shl 2);`
`BCM2838_DMA_ENABLE_3 = (1 shl 3);`
`BCM2838_DMA_ENABLE_4 = (1 shl 4);`
`BCM2838_DMA_ENABLE_5 = (1 shl 5);`
`BCM2838_DMA_ENABLE_6 = (1 shl 6);`
`BCM2838_DMA_ENABLE_7 = (1 shl 7);`
`BCM2838_DMA_ENABLE_8 = (1 shl 8);`
`BCM2838_DMA_ENABLE_9 = (1 shl 9);`
`BCM2838_DMA_ENABLE_10 = (1 shl 10);`
`BCM2838_DMA_ENABLE_11 = (1 shl 11);`
`BCM2838_DMA_ENABLE_12 = (1 shl 12);`
`BCM2838_DMA_ENABLE_13 = (1 shl 13);`
`BCM2838_DMA_ENABLE_14 = (1 shl 14);`
Bits 15:23 Reserved
`BCM2838_DMA_PAGE_MASK = ($F shl 24);`	Set the 1G SDRAM ram page that the 30-bit DMA engines (DMA0-6) will access when addressing the 1G uncached range C000_0000->ffff_ffff
`BCM2838_DMA_PAGE_DEFAULT = (0 shl 24);`	addr[29:0] )
`BCM2838_DMA_PAGELITE_MASK = ($F shl 28);`	Set the 1G SDRAM ram page that the DMA Lite engines (DMA7-10) will access when addressing the 1G uncached range C000_0000->ffff_ffff
`BCM2838_DMA_PAGELITE_DEFAULT = (0 shl 28);`	addr[29:0] )

BCM2838 DMA engine DREQ peripheral BCM2838_DMA_DREQ_*

See: Section 4

`BCM2838_DMA_DREQ_NONE = 0;`
`BCM2838_DMA_DREQ_DSI0 = 1;`
`BCM2838_DMA_DREQ_PWM1 = 1;`	The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
`BCM2838_DMA_DREQ_PCMTX = 2;`
`BCM2838_DMA_DREQ_PCMRX = 3;`
`BCM2838_DMA_DREQ_SMI = 4;`
`BCM2838_DMA_DREQ_PWM0 = 5;`
`BCM2838_DMA_DREQ_SPI0TX = 6;`
`BCM2838_DMA_DREQ_SPI0RX = 7;`
`BCM2838_DMA_DREQ_BSCSPITX = 8;`	BSC/SPI Slave
`BCM2838_DMA_DREQ_BSCSPIRX = 9;`	BSC/SPI Slave
`BCM2838_DMA_DREQ_HDMI0 = 10;`
`BCM2838_DMA_DREQ_EMMC0 = 11;`	SDHCI
`BCM2838_DMA_DREQ_UART0TX = 12;`
`BCM2838_DMA_DREQ_EMMC1 = 13;`	SDHOST
`BCM2838_DMA_DREQ_UART0RX = 14;`
`BCM2838_DMA_DREQ_DSI1 = 15;`
`BCM2838_DMA_DREQ_SPI1TX = 16;`
`BCM2838_DMA_DREQ_HDMI1 = 17;`
`BCM2838_DMA_DREQ_SPI1RX = 18;`
`BCM2838_DMA_DREQ_UART3TX = 19;`
`BCM2838_DMA_DREQ_SPI4TX = 19;`	The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
`BCM2838_DMA_DREQ_UART3RX = 20;`
`BCM2838_DMA_DREQ_SPI4RX = 20;`	The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
`BCM2838_DMA_DREQ_UART5TX = 21;`
`BCM2838_DMA_DREQ_SPI5TX = 21;`	The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
`BCM2838_DMA_DREQ_UART5RX = 22;`
`BCM2838_DMA_DREQ_SPI5RX = 22;`	The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
`BCM2838_DMA_DREQ_SPI6TX = 23;`
`BCM2838_DMA_DREQ_SCALER_FIFO0 = 24;`	Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
`BCM2838_DMA_DREQ_SCALER_FIFO1 = 25;`	Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
`BCM2838_DMA_DREQ_SCALER_FIFO2 = 26;`	Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
`BCM2838_DMA_DREQ_SPI6RX = 27;`
`BCM2838_DMA_DREQ_UART2TX = 28;`
`BCM2838_DMA_DREQ_UART2RX = 29;`
`BCM2838_DMA_DREQ_UART4TX = 30;`
`BCM2838_DMA_DREQ_UART4RX = 31;`

BCM2838 BSC (I2C0/1/2) control BCM2838_BSC_C_*

See: Section 3.2

`BCM2838_BSC_C_I2CEN = (1 shl 15);`	I2C Enable (0 = BSC controller is disabled / 1 = BSC controller is enabled)
`BCM2838_BSC_C_INTR = (1 shl 10);`	INTR Interrupt on RX (0 = Don t generate interrupts on RXR condition / 1 = Generate interrupt while RXR = 1)
`BCM2838_BSC_C_INTT = (1 shl 9);`	INTT Interrupt on TX (0 = Don t generate interrupts on TXW condition / 1 = Generate interrupt while TXW = 1)
`BCM2838_BSC_C_INTD = (1 shl 8);`	INTD Interrupt on DONE (0 = Don t generate interrupts on DONE condition / 1 = Generate interrupt while DONE = 1)
`BCM2838_BSC_C_ST = (1 shl 7);`	ST Start Transfer (0 = No action / 1 = Start a new transfer. One shot operation. Read back as 0)
`BCM2838_BSC_C_CLEAR = (1 shl 5);`	CLEAR FIFO Clear (00 = No action / x1 = Clear FIFO. One shot operation / 1x = Clear FIFO. One shot operation)
`BCM2838_BSC_C_READ = (1 shl 0);`	READ Read Transfer (0 = Write Packet Transfer / 1 = Read Packet Transfer)

BCM2838 BSC (I2C0/1/2) status BCM2838_BSC_S_*

See: Section 3.2

`BCM2838_BSC_S_CLKT = (1 shl 9);`	CLKT Clock Stretch Timeout (0 = No errors detected. 1 = Slave has held the SCL signal low (clock stretching) for longer and that specified in the I2CCLKT register Cleared by writing 1 to the field.)
`BCM2838_BSC_S_ERR = (1 shl 8);`	ERR ACK Error (0 = No errors detected. 1 = Slave has not acknowledged its address. Cleared by writing 1 to the field.)
`BCM2838_BSC_S_RXF = (1 shl 7);`	RXF - FIFO Full (0 = FIFO is not full. 1 = FIFO is full. If a read is underway, no further serial data will be received until data is read from FIFO.)
`BCM2838_BSC_S_TXE = (1 shl 6);`	TXE - FIFO Empty (0 = FIFO is not empty. 1 = FIFO is empty. If a write is underway, no further serial data can be transmitted until data is written to the FIFO.)
`BCM2838_BSC_S_RXD = (1 shl 5);`	RXD - FIFO contains Data (0 = FIFO is empty. 1 = FIFO contains at least 1 byte. Cleared by reading sufficient data from FIFO.)
`BCM2838_BSC_S_TXD = (1 shl 4);`	TXD - FIFO can accept Data (0 = FIFO is full. The FIFO cannot accept more data. 1 = FIFO has space for at least 1 byte.)
`BCM2838_BSC_S_RXR = (1 shl 3);`	RXR - FIFO needs Reading (full) (0 = FIFO is less than full and a read is underway. 1 = FIFO is or more full and a read is underway. Cleared by reading sufficient data from the FIFO.)
`BCM2838_BSC_S_TXW = (1 shl 2);`	TXW - FIFO needs Writing (full) (0 = FIFO is at least full and a write is underway (or sufficient data to send). 1 = FIFO is less then full and a write is underway. Cleared by writing sufficient data to the FIFO.)
`BCM2838_BSC_S_DONE = (1 shl 1);`	DONE Transfer Done (0 = Transfer not completed. 1 = Transfer complete. Cleared by writing 1 to the field.)
`BCM2838_BSC_S_TA = (1 shl 0);`	TA Transfer Active (0 = Transfer not active. 1 = Transfer active.)

BCM2838 BSC (I2C0/1/2) data length BCM2838_BSC_DLEN_*

See: Section 3.2

`BCM2838_BSC_DLEN_MASK = $FFFF;`	Data Length. (Writing to DLEN specifies the number of bytes to be transmitted/received. Reading from DLEN when TA = 1 or DONE = 1, returns the number of bytes still to be transmitted or received.)

BCM2838 BSC (I2C0/1/2) slave address BCM2838_BSC_A_*

See: Section 3.2

`BCM2838_BSC_A_MASK = $7F;`	Slave Address

BCM2838 BSC (I2C0/1/2) data FIFO BCM2838_BSC_FIFO_*

See: Section 3.2

`BCM2838_BSC_FIFO_MASK = $FF;`	Writes to the register write transmit data to the FIFO. Reads from register reads received data from the FIFO.
`BCM2838_BSC_FIFO_SIZE = 16;`

BCM2838 BSC (I2C0/1/2) clock divider BCM2838_BSC_CDIV_*

See: Section 3.2

`BCM2838_BSC_CDIV_MASK = $FFFF;`	Clock Divider (SCL = core clock / CDIV) (CDIV is always rounded down to an even number)

BCM2838 BSC (I2C0/1/2) data delay BCM2838_BSC_DEL_*

See: Section 3.2

`BCM2838_BSC_DEL_FEDL_MASK = ($FFFF shl 16);`	FEDL Falling Edge Delay (Number of core clock cycles to wait after the falling edge of SCL before outputting next bit of data)
`BCM2838_BSC_DEL_REDL_MASK = ($FFFF shl 0);`	REDL Rising Edge Delay (Number of core clock cycles to wait after the rising edge of SCL before reading the next bit of data)

BCM2838 BSC (I2C0/1/2) clock stretch timeout BCM2838_BSC_CLKT_TOUT_*

See: Section 3.2

`BCM2838_BSC_CLKT_TOUT_MASK = $FFFF;`	TOUT Clock Stretch Timeout Value (Number of SCL clock cycles to wait after the rising edge of SCL before deciding that the slave is not responding)

BCM2838 SPI0 BCM2838_SPI0_*

See: Section 10.5

`BCM2838_SPI0_CS_LEN_LONG = (1 shl 25);`	Enable Long data word in Lossi mode if DMA_LEN is set (0 = writing to the FIFO will write a single byte / 1 = writing to the FIFO will write a 32 bit word)
`BCM2838_SPI0_CS_DMA_LEN = (1 shl 24);`	Enable DMA mode in Lossi mode
`BCM2838_SPI0_CS_CSPOL2 = (1 shl 23);`	Chip Select 2 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
`BCM2838_SPI0_CS_CSPOL1 = (1 shl 22);`	Chip Select 1 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
`BCM2838_SPI0_CS_CSPOL0 = (1 shl 21);`	Chip Select 0 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
`BCM2838_SPI0_CS_RXF = (1 shl 20);`	RXF - RX FIFO Full (0 = RXFIFO is not full / 1 = RX FIFO is full. No further serial data will be sent/received until data is read from FIFO.)
`BCM2838_SPI0_CS_RXR = (1 shl 19);`	RXR RX FIFO needs Reading (full) (0 = RX FIFO is less than full (or not active TA = 0) / 1 = RX FIFO is or more full. Cleared by reading sufficient data from the RX FIFO or setting TA to 0.)
`BCM2838_SPI0_CS_TXD = (1 shl 18);`	TXD TX FIFO can accept Data (0 = TX FIFO is full and so cannot accept more data / 1 = TX FIFO has space for at least 1 byte)
`BCM2838_SPI0_CS_RXD = (1 shl 17);`	RXD RX FIFO contains Data (0 = RX FIFO is empty / 1 = RX FIFO contains at least 1 byte)
`BCM2838_SPI0_CS_DONE = (1 shl 16);`	DONE Transfer Done (0 = Transfer is in progress (or not active TA = 0) / 1 = Transfer is complete. Cleared by writing more data to the TX FIFO or setting TA to 0.)
`BCM2838_SPI0_CS_TE_EN = (1 shl 15);`	Unused
`BCM2838_SPI0_CS_LMONO = (1 shl 14);`	Unused
`BCM2838_SPI0_CS_LEN = (1 shl 13);`	LEN LoSSI enable (0 = The serial interface will behave as an SPI master / 1 = The serial interface will behave as a LoSSI master)
`BCM2838_SPI0_CS_REN = (1 shl 12);`	REN Read Enable. If this bit is set, the SPI peripheral will be able to send data to this device (0 = We intend to write to the SPI peripheral / 1 = We intend to read from the SPI peripheral)
`BCM2838_SPI0_CS_ADCS = (1 shl 11);`	ADCS Automatically Deassert Chip Select (0 = Don t automatically deassert chip select at the end of a DMA transfer chip select is manually controlled by software / 1 = Automatically deassert chip select at the end of a DMA transfer as determined by SPIDLEN)
`BCM2838_SPI0_CS_INTR = (1 shl 10);`	INTR Interrupt on RXR (0 = Don t generate interrupts on RX FIFO condition / 1 = Generate interrupt while RXR = 1)
`BCM2838_SPI0_CS_INTD = (1 shl 9);`	INTD Interrupt on Done (0 = Don t generate interrupt on transfer complete / 1 = Generate interrupt when DONE = 1)
`BCM2838_SPI0_CS_DMAEN = (1 shl 8);`	DMAEN DMA Enable (0 = No DMA requests will be issued / 1 = Enable DMA operation. Peripheral generates data requests. These will be taken in four-byte words until the SPIDLEN has been reached.
`BCM2838_SPI0_CS_TA = (1 shl 7);`	Transfer Active (0 = Transfer not active / 1 = Transfer active)
`BCM2838_SPI0_CS_CSPOL = (1 shl 6);`	Chip Select Polarity (0 = Chip select lines are active low / 1 = Chip select lines are active high
`BCM2838_SPI0_CS_CLEAR_RX = (1 shl 5);`	CLEAR FIFO Clear (00 = No action / x1 = Clear TX FIFO. One shot operation / 1x = Clear RX FIFO. One shot operation.)
`BCM2838_SPI0_CS_CLEAR_TX = (1 shl 4);`	As above
`BCM2838_SPI0_CS_CPOL = (1 shl 3);`	Clock Polarity (0 = Rest state of clock = low / 1 = Rest state of clock = high)
`BCM2838_SPI0_CS_CPHA = (1 shl 2);`	Clock Phase (0 = First SCLK transition at middle of data bit / 1 = First SCLK transition at beginning of data bit)
`BCM2838_SPI0_CS_CS_0 = (0 shl 0);`	Chip Select (00 = Chip select 0 / 01 = Chip select 1 / 10 = Chip select 2 / 11 = Reserved
`BCM2838_SPI0_CS_CS_1 = (1 shl 0);`	As above
`BCM2838_SPI0_CS_CS_2 = (2 shl 0);`	As above

`BCM2838_SPI0_CS_CS_MASK = (3 shl 0);`

`BCM2838_SPI0_FIFO_DMA_DATA = $FFFFFFFF;`	DMA Mode (DMAEN set) If TA is clear, the first 32-bit write to this register will control SPIDLEN and SPICS. Subsequent reads and writes will be taken as four-byte data words to be read/written to the FIFOs.
`BCM2838_SPI0_FIFO_IRQ_DATA = $000000FF;`	Poll/Interrupt Mode (DMAEN clear, TA set) Writes to the register write bytes to TX FIFO. Reads from register read bytes from the RX FIFO.

`BCM2838_SPI0_CLK_CDIV = $0000FFFF;`	Clock Divider (SCLK = Core Clock / CDIV) If CDIV is set to 0, the divisor is 65536. The divisor must be a multiple of 2. Odd numbers rounded down. The maximum SPI clock rate is of the APB clock.

`BCM2838_SPI0_DLEN_LEN = $0000FFFF;`	Data Length. The number of bytes to transfer. This field is only valid for DMA mode (DMAEN set) and controls how many bytes to transmit (and therefore receive).

`BCM2838_SPI0_LTOH_TOH = $0000000F;`	This sets the Output Hold delay in APB clocks (A value of 0 causes a 1 clock delay)

`BCM2838_SPI0_DC_RPANIC = ($FF shl 24);`	DMA Read Panic Threshold (Generate the Panic signal to the RX DMA engine whenever the RX FIFO level is greater than this amount)
`BCM2838_SPI0_DC_RDREQ = ($FF shl 16);`	DMA Read Request Threshold (Generate A DREQ to the RX DMA engine whenever the RX FIFO level is greater than this amount) (RX DREQ is also generated if thetransfer has finished but the RXFIFO isn't empty)
`BCM2838_SPI0_DC_TPANIC = ($FF shl 8);`	DMA Write Panic Threshold (Generate the Panic signal to the TX DMA engine whenever the TX FIFO level is less than or equal to this amount)
`BCM2838_SPI0_DC_TDREQ = ($FF shl 0);`	DMA Write Request Threshold (Generate a DREQ signal to the TX DMA engine whenever the TX FIFO level is less than or equal to this amount)

BCM2838 I2C/SPI Slave register

See: Section 11.2

BCM2838 AUX (UART1, SPI1 and SPI2) register

See: Section 2.1

BCM2838 PCM/I2S register

See: Section 8.8

BCM2838 PWM control BCM2838_PWM_CTL_*

See: Section 9.6

`BCM2838_PWM_CTL_MSEN2 = (1 shl 15);`	Channel 2 M/S Enable (0: PWM algorithm is used / 1: M/S transmission is used)
Bit 14 Reserved - Write as 0, read as don't care
`BCM2838_PWM_CTL_USEF2 = (1 shl 13);`	Channel 2 Use Fifo (0: Data register is transmitted / 1: Fifo is used for transmission)
`BCM2838_PWM_CTL_POLA2 = (1 shl 12);`	Channel 2 Polarity (0 : 0=low 1=high / 1: 1=low 0=high)
`BCM2838_PWM_CTL_SBIT2 = (1 shl 11);`	Channel 2 Silence Bit (Defines the state of the output when no transmission takes place)
`BCM2838_PWM_CTL_RPTL2 = (1 shl 10);`	Channel 2 Repeat Last Data (0: Transmission interrupts when FIFO is empty / 1: Last data in FIFO is transmitted repeatedly until FIFO is not empty)
`BCM2838_PWM_CTL_MODE2 = (1 shl 9);`	Channel 2 Mode (0: PWM mode / 1: Serialiser mode)
`BCM2838_PWM_CTL_PWEN2 = (1 shl 8);`	Channel 2 Enable (0: Channel is disabled / 1: Channel is enabled)
`BCM2838_PWM_CTL_MSEN1 = (1 shl 7);`	Channel 1 M/S Enable (0: PWM algorithm is used / 1: M/S transmission is used)
`BCM2838_PWM_CTL_CLRF1 = (1 shl 6);`	Clear Fifo (1: Clears FIFO / 0: Has no effect) (This is a single shot operation. This bit always reads 0.)
`BCM2838_PWM_CTL_USEF1 = (1 shl 5);`	Channel 1 Use Fifo (0: Data register is transmitted / 1: Fifo is used for transmission)
`BCM2838_PWM_CTL_POLA1 = (1 shl 4);`	Channel 1 Polarity (0 : 0=low 1=high / 1: 1=low 0=high)
`BCM2838_PWM_CTL_SBIT1 = (1 shl 3);`	Channel 1 Silence Bit (Defines the state of the output when no transmission takes place)
`BCM2838_PWM_CTL_RPTL1 = (1 shl 2);`	Channel 1 Repeat Last Data (0: Transmission interrupts when FIFO is empty / 1: Last data in FIFO is transmitted repeatedly until FIFO is not empty)
`BCM2838_PWM_CTL_MODE1 = (1 shl 1);`	Channel 1 Mode (0: PWM mode / 1: Serialiser mode)
`BCM2838_PWM_CTL_PWEN1 = (1 shl 0);`	Channel 1 Enable (0: Channel is disabled / 1: Channel is enabled)

BCM2838 PWM status BCM2838_PWM_STA_*

See: Section 9.6

`BCM2838_PWM_STA_STA4 = (1 shl 12);`	Channel 4 State
`BCM2838_PWM_STA_STA3 = (1 shl 11);`	Channel 3 State
`BCM2838_PWM_STA_STA2 = (1 shl 10);`	Channel 2 State
`BCM2838_PWM_STA_STA1 = (1 shl 9);`	Channel 1 State
`BCM2838_PWM_STA_BERR = (1 shl 8);`	Bus Error Flag
`BCM2838_PWM_STA_GAPO4 = (1 shl 7);`	Channel 4 Gap Occurred Flag
`BCM2838_PWM_STA_GAPO3 = (1 shl 6);`	Channel 3 Gap Occurred Flag
`BCM2838_PWM_STA_GAPO2 = (1 shl 5);`	Channel 2 Gap Occurred Flag
`BCM2838_PWM_STA_GAPO1 = (1 shl 4);`	Channel 1 Gap Occurred Flag
`BCM2838_PWM_STA_RERR1 = (1 shl 3);`	Fifo Read Error Flag
`BCM2838_PWM_STA_WERR1 = (1 shl 2);`	Fifo Write Error Flag
`BCM2838_PWM_STA_EMPT1 = (1 shl 1);`	Fifo Empty Flag
`BCM2838_PWM_STA_FULL1 = (1 shl 0);`	Fifo Full Flag

BCM2838 PWM DMA configuration BCM2838_PWM_DMAC_*

See: Section 9.6

`BCM2838_PWM_DMAC_ENAB = (1 shl 31);`	DMA Enable (0: DMA disabled / 1: DMA enabled)
`BCM2838_PWM_DMAC_PANIC = ($FF shl 8);`	DMA Threshold for PANIC signal (Default: 0x7)
`BCM2838_PWM_DMAC_DREQ = ($FF shl 0);`	DMA Threshold for DREQ signal (Default: 0x7)

BCM2838 Pulse Width Modulator (PWM) BCM2838_PWM_ *

`BCM2838_PWM_CTL = $00000000;`	PWM Control
`BCM2838_PWM_STA = $00000004;`	PWM Status
`BCM2838_PWM_DMAC = $00000008;`	PWM DMA Configuration
`BCM2838_PWM_RNG1 = $00000010;`	PWM Channel 1 Range
`BCM2838_PWM_DAT1 = $00000014;`	PWM Channel 1 Data
`BCM2838_PWM_FIF1 = $00000018;`	PWM FIFO Input
`BCM2838_PWM_RNG2 = $00000020;`	PWM Channel 2 Range
`BCM2838_PWM_DAT2 = $00000024;`	PWM Channel 2 Data

BCM2838 PL011 UART data BCM2838_PL011_*

See: Section 13.4

`BCM2838_PL011_DR_OE = (1 shl 11);`	Overrun error
`BCM2838_PL011_DR_BE = (1 shl 10);`	Break error
`BCM2838_PL011_DR_PE = (1 shl 9);`	Parity error
`BCM2838_PL011_DR_FE = (1 shl 8);`	Framing error
`BCM2838_PL011_DR_DATA = ($FF shl 0);`	Receive / Transmit data
`BCM2838_PL011_DR_ERROR = BCM2838_PL011_DR_OE or BCM2838_PL011_DR_BE or BCM2838_PL011_DR_PE or BCM2838_PL011_DR_FE;`

BCM2838 PL011 UART receive status/error clear BCM2838_PL011_RSRECR_*

See: Section 13.4

`BCM2838_PL011_RSRECR_OE = (1 shl 3);`	Overrun error
`BCM2838_PL011_RSRECR_BE = (1 shl 2);`	Break error
`BCM2838_PL011_RSRECR_PE = (1 shl 1);`	Parity error
`BCM2838_PL011_RSRECR_FE = (1 shl 0);`	Framing error

BCM2838 PL011 UART flag BCM2838_PL011_FR_*

See: Section 13.4

`BCM2838_PL011_FR_RI = (1 shl 8);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_FR_TXFE = (1 shl 7);`	Transmit FIFO empty
`BCM2838_PL011_FR_RXFF = (1 shl 6);`	Receive FIFO full
`BCM2838_PL011_FR_TXFF = (1 shl 5);`	Transmit FIFO full
`BCM2838_PL011_FR_RXFE = (1 shl 4);`	Receive FIFO empty
`BCM2838_PL011_FR_BUSY = (1 shl 3);`	UART busy
`BCM2838_PL011_FR_DCD = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_FR_DSR = (1 shl 1);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_FR_CTS = (1 shl 0);`	Clear to send (This bit is the complement of the UART clear to send, nUARTCTS, modem status input. That is, the bit is 1 when nUARTCTS is LOW.)

BCM2838 PL011 UART IrDA

See: Section 13.4

This register is disabled, writing to it has no effect and reading returns 0

BCM2838 PL011 UART integer baud rate divisor BCM2838_PL011_IBRD_*

`BCM2838_PL011_IBRD_MASK = ($FFFF shl 0);`

BCM2838 PL011 UART fractional baud rate divisor BCM2838_PL011_FBRD_*

See: Section 13.4

`BCM2838_PL011_FBRD_MASK = ($3F shl 0);`

BCM2838 PL011 UART line control BCM2838_PL011_LCRH_*

See: Section 13.4

`BCM2838_PL011_LCRH_SPS = (1 shl 7);`	Stick parity select
`BCM2838_PL011_LCRH_WLEN = (3 shl 5);`	Word length
`BCM2838_PL011_LCRH_WLEN8 = (3 shl 5);`	8 bits
`BCM2838_PL011_LCRH_WLEN7 = (2 shl 5);`	7 bits
`BCM2838_PL011_LCRH_WLEN6 = (1 shl 5);`	6 bits
`BCM2838_PL011_LCRH_WLEN5 = (0 shl 5);`	5 bits
`BCM2838_PL011_LCRH_FEN = (1 shl 4);`	Enable FIFOs
`BCM2838_PL011_LCRH_STP2 = (1 shl 3);`	Two stop bits select
`BCM2838_PL011_LCRH_EPS = (1 shl 2);`	Even parity select (0 = odd parity / 1 = even parity)
`BCM2838_PL011_LCRH_PEN = (1 shl 1);`	Parity enable
`BCM2838_PL011_LCRH_BRK = (1 shl 0);`	Send break

BCM2838 PL011 UART control BCM2838_PL011_CR_*

See: Section 13.4

`BCM2838_PL011_CR_CTSEN = (1 shl 15);`	CTS hardware flow control enable (If this bit is set to 1 data is only transmitted when the nUARTCTS signal is asserted)
`BCM2838_PL011_CR_RTSEN = (1 shl 14);`	RTS hardware flow control enable (If this bit is set to 1 data is only requested when there is space in the receive FIFO for it to be received)
`BCM2838_PL011_CR_OUT2 = (1 shl 13);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_CR_OUT1 = (1 shl 12);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_CR_RTS = (1 shl 11);`	Request to send (This bit is the complement of the UART request to send, nUARTRTS, modem status output. That is, when the bit is programmed to a 1 then nUARTRTS is LOW.)
`BCM2838_PL011_CR_DTR = (1 shl 10);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_CR_RXE = (1 shl 9);`	Receive enable
`BCM2838_PL011_CR_TXE = (1 shl 8);`	Transmit enable
`BCM2838_PL011_CR_LBE = (1 shl 7);`	Loopback enable
Bits 6:3 Reserved - Write as 0, read as don't care
`BCM2838_PL011_CR_SIRLP = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_CR_SIREN = (1 shl 1);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_CR_UARTEN = (1 shl 0);`	UART enable

BCM2838 PL011 UART interrupt FIFO level select BCM2838_PL011_IFLS_*

See: Section 13.4

`BCM2838_PL011_IFLS_RXIFPSEL = (7 shl 9);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_IFLS_TXIFPSEL = (7 shl 6);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_IFLS_RXIFLSEL = (7 shl 3);`	Receive interrupt FIFO level select
`BCM2838_PL011_IFLS_RXIFLSEL1_8 = (0 shl 3);`	b000 = Receive FIFO becomes >= 1/8 full
`BCM2838_PL011_IFLS_RXIFLSEL1_4 = (1 shl 3);`	b001 = Receive FIFO becomes >= 1/4 full
`BCM2838_PL011_IFLS_RXIFLSEL1_2 = (2 shl 3);`	b010 = Receive FIFO becomes >= 1/2 full
`BCM2838_PL011_IFLS_RXIFLSEL3_4 = (3 shl 3);`	b011 = Receive FIFO becomes >= 3/4 full
`BCM2838_PL011_IFLS_RXIFLSEL7_8 = (4 shl 3);`	b100 = Receive FIFO becomes >= 7/8 full
`BCM2838_PL011_IFLS_TXIFLSEL = (7 shl 0);`	Transmit interrupt FIFO level select
`BCM2838_PL011_IFLS_TXIFLSEL1_8 = (0 shl 0);`	b000 = Transmit FIFO becomes <= 1/8 full
`BCM2838_PL011_IFLS_TXIFLSEL1_4 = (1 shl 0);`	b001 = Transmit FIFO becomes <= 1/4 full
`BCM2838_PL011_IFLS_TXIFLSEL1_2 = (2 shl 0);`	b010 = Transmit FIFO becomes <= 1/2 full
`BCM2838_PL011_IFLS_TXIFLSEL3_4 = (3 shl 0);`	b011 = Transmit FIFO becomes <= 3/4 full
`BCM2838_PL011_IFLS_TXIFLSEL7_8 = (4 shl 0);`	b100 = Transmit FIFO becomes <= 7/8 full

BCM2838 PL011 UART interrupt mask set/clear BCM2838_PL011_IMSC_*

See: Section 13.4

`BCM2838_PL011_IMSC_OEIM = (1 shl 10);`	Overrun error interrupt mask
`BCM2838_PL011_IMSC_BEIM = (1 shl 9);`	Break error interrupt mask
`BCM2838_PL011_IMSC_PEIM = (1 shl 8);`	Parity error interrupt mask
`BCM2838_PL011_IMSC_FEIM = (1 shl 7);`	Framing error interrupt mask
`BCM2838_PL011_IMSC_RTIM = (1 shl 6);`	Receive timeout interrupt mask
`BCM2838_PL011_IMSC_TXIM = (1 shl 5);`	Transmit interrupt mask
`BCM2838_PL011_IMSC_RXIM = (1 shl 4);`	Receive interrupt mask
`BCM2838_PL011_IMSC_DSRMIM = (1 shl 3);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_IMSC_DCDMIM = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_IMSC_CTSMIM = (1 shl 1);`	nUARTCTS modem interrupt mask
`BCM2838_PL011_IMSC_RIMIM = (1 shl 0);`	Unsupported, write zero, read as don't care

BCM2838 PL011 UART raw interrupt status BCM2838_PL011_RIS_*

See: Section 13.4

`BCM2838_PL011_RIS_OERIS = (1 shl 10);`	Overrun error interrupt status
`BCM2838_PL011_RIS_BERIS = (1 shl 9);`	Break error interrupt status
`BCM2838_PL011_RIS_PERIS = (1 shl 8);`	Parity error interrupt status
`BCM2838_PL011_RIS_FERIS = (1 shl 7);`	Framing error interrupt status
`BCM2838_PL011_RIS_RTRIS = (1 shl 6);`	Receive timeout interrupt status
`BCM2838_PL011_RIS_TXRIS = (1 shl 5);`	Transmit interrupt status
`BCM2838_PL011_RIS_RXRIS = (1 shl 4);`	Receive interrupt status
`BCM2838_PL011_RIS_DSRMRIS = (1 shl 3);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_RIS_DCDMRIS = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_RIS_CTSMRIS = (1 shl 1);`	nUARTCTS modem interrupt status
`BCM2838_PL011_RIS_RIMRIS = (1 shl 0);`	Unsupported, write zero, read as don't care

BCM2838 PL011 UART masked interrupt status BCM2838_PL011_MIS_*

See: Section 13.4

`BCM2838_PL011_MIS_OEMIS = (1 shl 10);`	Overrun error masked interrupt status
`BCM2838_PL011_MIS_BEMIS = (1 shl 9);`	Break error masked interrupt status
`BCM2838_PL011_MIS_PEMIS = (1 shl 8);`	Parity error masked interrupt status
`BCM2838_PL011_MIS_FEMIS = (1 shl 7);`	Framing error masked interrupt status
`BCM2838_PL011_MIS_RTMIS = (1 shl 6);`	Receive timeout masked interrupt status
`BCM2838_PL011_MIS_TXMIS = (1 shl 5);`	Transmit masked interrupt status
`BCM2838_PL011_MIS_RXMIS = (1 shl 4);`	Receive masked interrupt status
`BCM2838_PL011_MIS_DSRMMIS = (1 shl 3);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_MIS_DCDMMIS = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_MIS_CTSMMIS = (1 shl 1);`	nUARTCTS modem masked interrupt status
`BCM2838_PL011_MIS_RIMMIS = (1 shl 0);`	Unsupported, write zero, read as don't care

BCM2838 PL011 UART interrupt clear BCM2838_PL011_ICR_*

See: Section 13.4

`BCM2838_PL011_ICR_OEIC = (1 shl 10);`	Overrun error interrupt clear
`BCM2838_PL011_ICR_BEIC = (1 shl 9);`	Break error interrupt clear
`BCM2838_PL011_ICR_PEIC = (1 shl 8);`	Parity error interrupt clear
`BCM2838_PL011_ICR_FEIC = (1 shl 7);`	Framing error interrupt clear
`BCM2838_PL011_ICR_RTIC = (1 shl 6);`	Receive timeout interrupt clear
`BCM2838_PL011_ICR_TXIC = (1 shl 5);`	Transmit interrupt clear
`BCM2838_PL011_ICR_RXIC = (1 shl 4);`	Receive interrupt clear
`BCM2838_PL011_ICR_DSRMIC = (1 shl 3);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_ICR_DCDMIC = (1 shl 2);`	Unsupported, write zero, read as don't care
`BCM2838_PL011_ICR_CTSMIC = (1 shl 1);`	nUARTCTS modem interrupt clear
`BCM2838_PL011_ICR_RIMIC = (1 shl 0);`	Unsupported, write zero, read as don't care

BCM2838 PL011 UART DMA control

See: Section 13.4

This register is disabled, writing to it has no effect and reading returns 0

BCM2838 PL011 UART test control

See: Section 13.4

BCM2838 PL011 UART integration test input

See: Section 13.4

BCM2838 PL011 UART integration test output

See: Section 13.4

BCM2838 PL011 UART test data

See: Section 13.4

BCM2838 ARM legacy interrupt controller BCM2838_ARM_INTERRUPT_*

`BCM2838_ARM_INTERRUPT_IRQ0_PENDING0 = $00000000;`	ARM Core 0 IRQ Enabled Interrupt Pending bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ0_PENDING1 = $00000004;`	ARM Core 0 IRQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ0_PENDING2 = $00000008;`	ARM Core 0 IRQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_0 = $00000010;`	Write to Set ARM Core 0 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_1 = $00000014;`	Write to Set ARM Core 0 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_2 = $00000018;`	Write to Set ARM Core 0 IRQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_0 = $00000020;`	Write to Clear ARM Core 0 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_1 = $00000024;`	Write to Clear ARM Core 0 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_2 = $00000028;`	Write to Clear ARM Core 0 IRQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ_STATUS0 = $00000030;`	Interrupt Line bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ_STATUS1 = $00000034;`	Interrupt Line bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ_STATUS2 = $00000038;`	Interrupt Line bits [79:64]

`BCM2838_ARM_INTERRUPT_IRQ1_PENDING0 = $00000040;`	ARM Core 1 IRQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ1_PENDING1 = $00000044;`	ARM Core 1 IRQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ1_PENDING2 = $00000048;`	ARM Core 1 IRQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_0 = $00000050;`	Write to Set ARM Core 1 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_1 = $00000054;`	Write to Set ARM Core 1 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_2 = $00000058;`	Write to Set ARM Core 1 IRQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_0 = $00000060;`	Write to Clear ARM Core 1 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_1 = $00000064;`	Write to Clear ARM Core 1 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_2 = $00000068;`	Write to Clear ARM Core 1 IRQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_IRQ2_PENDING0 = $00000080;`	ARM Core 2 IRQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ2_PENDING1 = $00000084;`	ARM Core 2 IRQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ2_PENDING2 = $00000088;`	ARM Core 2 IRQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_0 = $00000090;`	Write to Set ARM Core 2 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_1 = $00000094;`	Write to Set ARM Core 2 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_2 = $00000098;`	Write to Set ARM Core 2 IRQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_0 = $000000A0;`	Write to Clear ARM Core 2 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_1 = $000000A4;`	Write to Clear ARM Core 2 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_2 = $000000A8;`	Write to Clear ARM Core 2 IRQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_IRQ3_PENDING0 = $000000C0;`	ARM Core 3 IRQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ3_PENDING1 = $000000C4;`	ARM Core 3 IRQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ3_PENDING2 = $000000C8;`	ARM Core 3 IRQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_0 = $000000D0;`	Write to Set ARM Core 3 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_1 = $000000D4;`	Write to Set ARM Core 3 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_2 = $000000D8;`	Write to Set ARM Core 3 IRQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_0 = $000000E0;`	Write to Clear ARM Core 3 IRQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_1 = $000000E4;`	Write to Clear ARM Core 3 IRQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_2 = $000000E8;`	Write to Clear ARM Core 3 IRQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_FIQ0_PENDING0 = $00000100;`	ARM Core 0 FIQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ0_PENDING1 = $00000104;`	ARM Core 0 FIQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ0_PENDING2 = $00000108;`	ARM Core 0 FIQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_0 = $00000110;`	Write to Set ARM Core 0 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_1 = $00000114;`	Write to Set ARM Core 0 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_2 = $00000118;`	Write to Set ARM Core 0 FIQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_0 = $00000120;`	Write to Clear ARM Core 0 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_1 = $00000124;`	Write to Clear ARM Core 0 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_2 = $00000128;`	Write to Clear ARM Core 0 FIQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_FIQ1_PENDING0 = $00000140;`	ARM Core 1 FIQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ1_PENDING1 = $00000144;`	ARM Core 1 FIQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ1_PENDING2 = $00000148;`	ARM Core 1 FIQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_0 = $00000150;`	Write to Set ARM Core 1 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_1 = $00000154;`	Write to Set ARM Core 1 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_2 = $00000158;`	Write to Set ARM Core 1 FIQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_0 = $00000160;`	Write to Clear ARM Core 1 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_1 = $00000164;`	Write to Clear ARM Core 1 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_2 = $00000168;`	Write to Clear ARM Core 1 FIQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_FIQ2_PENDING0 = $00000180;`	ARM Core 2 FIQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ2_PENDING1 = $00000184;`	ARM Core 2 FIQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ2_PENDING2 = $00000188;`	ARM Core 2 FIQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_0 = $00000190;`	Write to Set ARM Core 2 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_1 = $00000194;`	Write to Set ARM Core 2 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_2 = $00000198;`	Write to Set ARM Core 2 FIQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_0 = $000001A0;`	Write to Clear ARM Core 2 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_1 = $000001A4;`	Write to Clear ARM Core 2 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_2 = $000001A8;`	Write to Clear ARM Core 2 FIQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_FIQ3_PENDING0 = $000001C0;`	ARM Core 3 FIQ Enabled Interrupt pending bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ3_PENDING1 = $000001C4;`	ARM Core 3 FIQ Enabled Interrupt pending bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ3_PENDING2 = $000001C8;`	ARM Core 3 FIQ Enabled Interrupt pending bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_0 = $000001D0;`	Write to Set ARM Core 3 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_1 = $000001D4;`	Write to Set ARM Core 3 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_2 = $000001D8;`	Write to Set ARM Core 3 FIQ enable bits [79:64]
`BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_0 = $000001E0;`	Write to Clear ARM Core 3 FIQ enable bits [31:0]
`BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_1 = $000001E4;`	Write to Clear ARM Core 3 FIQ enable bits [63:32]
`BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_2 = $000001E8;`	Write to Clear ARM Core 3 FIQ enable bits [79:64]

`BCM2838_ARM_INTERRUPT_SWIRQ_SET = $000001F0;`	Write to Set Software Interrupt sources
`BCM2838_ARM_INTERRUPT_SWIRQ_CLEAR = $000001F4;`	Write to Clear Software Interrupt sources

`BCM2838_ARM_INTERRUPT_CORE_OFFSET = BCM2838_ARM_INTERRUPT_IRQ1_PENDING0 - BCM2838_ARM_INTERRUPT_IRQ0_PENDING0;`	Offset between Core registers
`BCM2838_ARM_INTERRUPT_FIQ_OFFSET = BCM2838_ARM_INTERRUPT_FIQ0_PENDING0 - BCM2838_ARM_INTERRUPT_IRQ0_PENDING0;`	Offset betwwen IRQ and FIQ registers

BCM2838 ARM timer BCM2838_ARM_TIMER_*

See: Section 14.2

`BCM2838_ARM_TIMER_CONTROL_COUNTER_PRESCALE = ($FF shl 16);`	Free running counter pre-scaler (Freq is sys_clk/(prescale+1))
`BCM2838_ARM_TIMER_CONTROL_COUNTER_ENABLED = (1 shl 9);`	0 : Free running counter Disabled / 1 : Free running counter Enabled
`BCM2838_ARM_TIMER_CONTROL_DEBUG_HALT = (1 shl 8);`	0 : Timers keeps running if ARM is in debug halted mode / 1 : Timers halted if ARM is in debug halted mode
`BCM2838_ARM_TIMER_CONTROL_TIMER_ENABLED = (1 shl 7);`	0 : Timer disabled / 1 : Timer enabled
`BCM2838_ARM_TIMER_CONTROL_INT_ENABLED = (1 shl 5);`	0 : Timer interrupt disabled / 1 : Timer interrupt enabled
`BCM2838_ARM_TIMER_CONTROL_PRESCALE = (3 shl 2);`	Pre-scale bits: 00 : pre-scale is clock / 1 (No pre-scale) / 01 : pre-scale is clock / 16 / 10 : pre-scale is clock / 256 / 11 : pre-scale is clock / 1
`BCM2838_ARM_TIMER_CONTROL_32BIT = (1 shl 1);`	0 : 16-bit counters / 1 : 32-bit counter
`BCM2838_ARM_TIMER_CONTROL_ONESHOT = (1 shl 0);`	0 = wrapping mode (default) / 1 = one-shot mode (Not supported by BCM2838)

`BCM2838_ARM_TIMER_RAW_IRQ_PENDING = (1 shl 0);`	0 : The interrupt pending bits is clear / 1 : The interrupt pending bit is set

`BCM2838_ARM_TIMER_MASKED_IRQ_PENDING = (1 shl 0);`	0 : Interrupt line not asserted / 1 :Interrupt line is asserted, (the interrupt pending and the interrupt enable bit are set)

`BCM2838_ARM_TIMER_PREDIVIDER_MASK = ($3FF shl 0);`	Pre-divider value (timer_clock = apb_clock/(pre_divider+1))

BCM2838 power management, reset controller and watchdog BCM2838_PM_*

`BCM2838_PM_PASSWORD = $5A000000;`

`BCM2838_PM_RSTC_WRCFG_CLR = $FFFFFFCF;`
`BCM2838_PM_RSTC_WRCFG_SET= $00000030;`
`BCM2838_PM_RSTC_WRCFG_FULL_RESET = $00000020;`
`BCM2838_PM_RSTC_RESET = $00000102;`

`BCM2838_PM_RSTS_HADPOR_SET = $00001000;`
`BCM2838_PM_RSTS_HADSRH_SET = $00000400;`
`BCM2838_PM_RSTS_HADSRF_SET = $00000200;`
`BCM2838_PM_RSTS_HADSRQ_SET = $00000100;`
`BCM2838_PM_RSTS_HADWRH_SET = $00000040;`
`BCM2838_PM_RSTS_HADWRF_SET = $00000020;`
`BCM2838_PM_RSTS_HADWRQ_SET = $00000010;`
`BCM2838_PM_RSTS_HADDRH_SET = $00000004;`
`BCM2838_PM_RSTS_HADDRF_SET = $00000002;`
`BCM2838_PM_RSTS_HADDRQ_SET = $00000001;`

`BCM2838_PM_RSTS_RASPBERRYPI_HALT = $00000555;`	Special value to tell the Raspberry Pi firmware not to reboot, sets Boot Partition to 63 (0x3f).

`BCM2838_PM_WDOG_RESET = $00000000;`
`BCM2838_PM_WDOG_TIME_MASK = $000FFFFF;`

`BCM2838_PM_WDOG_TICKS_PER_SECOND = (1 shl 16);`
`BCM2838_PM_WDOG_TICKS_PER_MILLISECOND = (BCM2838_PM_WDOG_TICKS_PER_SECOND div 1000);`

BCM2838 random number generator BCM2838_RNG_*

`BCM2838_RNG_CTRL_OFFSET = $00;`
`BCM2838_RNG_CTRL_RNG_RBGEN_MASK = $00001FFF;`
`BCM2838_RNG_CTRL_RNG_RBGEN_ENABLE = $00000001;`
`BCM2838_RNG_CTRL_RNG_RBGEN_DISABLE = $00000000;`
`BCM2838_RNG_CTRL_RNG_DIV_CTRL_SHIFT = 13;`

`BCM2838_RNG_SOFT_RESET_OFFSET = $04;`
`BCM2838_RNG_SOFT_RESET = $00000001;`

`BCM2838_RBG_SOFT_RESET_OFFSET = $08;`
`BCM2838_RBG_SOFT_RESET = $00000001;`

`BCM2838_RNG_TOTAL_BIT_COUNT_OFFSET = $0C;`

`BCM2838_RNG_TOTAL_BIT_COUNT_THRESHOLD_OFFSET = $10;`

`BCM2838_RNG_INT_STATUS_OFFSET = $18;`
`BCM2838_RNG_INT_STATUS_MASTER_FAIL_LOCKOUT_IRQ_MASK = $80000000;`
`BCM2838_RNG_INT_STATUS_STARTUP_TRANSITIONS_MET_IRQ_MASK = $00020000;`
`BCM2838_RNG_INT_STATUS_NIST_FAIL_IRQ_MASK = $00000020;`
`BCM2838_RNG_INT_STATUS_TOTAL_BITS_COUNT_IRQ_MASK = $00000001;`

`BCM2838_RNG_INT_ENABLE_OFFSET = $1C;`

`BCM2838_RNG_FIFO_DATA_OFFSET = $20;`

`BCM2838_RNG_FIFO_COUNT_OFFSET = $24;`
`BCM2838_RNG_FIFO_COUNT_RNG_FIFO_COUNT_MASK = $000000FF;`
`BCM2838_RNG_FIFO_COUNT_RNG_FIFO_THRESHOLD_SHIFT = 8;`

BCM2838 clock management BCM2838_CM_*

See: Section 6

`BCM2838_CM_PASSWORD = $5A000000;`

BCM2838 clock manager control BCM2838_CM_CTL_*

See: Section 6.3

`BCM2838_CM_CTL_MASH_0 = (0 shl 9);`	MASH control - 0 = integer division
`BCM2838_CM_CTL_MASH_1 = (1 shl 9);`	MASH control - 1 = 1-stage MASH (equivalent to non-MASH dividers)
`BCM2838_CM_CTL_MASH_2 = (2 shl 9);`	MASH control - 2 = 2-stage MASH
`BCM2838_CM_CTL_MASH_3 = (3 shl 9);`	MASH control - 3 = 3-stage MASH (To avoid lock-ups and glitches do not change this control while BUSY=1 and do not change this control at the same time as asserting ENAB)
`BCM2838_CM_CTL_FLIP = (1 shl 8);`	MASH control - Invert the clock generator output (To avoid output glitches do not switch this control while BUSY=1)
`BCM2838_CM_CTL_BUSY = (1 shl 7);`	Clock generator is running (To avoid glitches and lock-ups, clock sources and setups must not be changed while this flag is set)
`BCM2838_CM_CTL_GATE = (1 shl 6);`	Unused
`BCM2838_CM_CTL_KILL = (1 shl 5);`	Kill the clock generator (0 = no action / 1 = stop and reset the clock generator) (This is intended for test/debug only)
`BCM2838_CM_CTL_ENAB = (1 shl 4);`	Enable the clock generator

`BCM2838_CM_CTL_SRC_GND = (0 shl 0);`	Clock source - 0 Hz GND
`BCM2838_CM_CTL_SRC_OSC = (1 shl 0);`	Clock source - 54 MHz Oscillator
`BCM2838_CM_CTL_SRC_TESTDEBUG0 = (2 shl 0);`	Clock source - 0 Hz Testdebug0
`BCM2838_CM_CTL_SRC_TESTDEBUG1 = (3 shl 0);`	Clock source - 0 Hz Testdebug1
`BCM2838_CM_CTL_SRC_PLLA = (4 shl 0);`	Clock source - 0 Hz PLLA
`BCM2838_CM_CTL_SRC_PLLC = (5 shl 0);`	Clock source - 1000 MHz PLLC (changes with overclock settings)
`BCM2838_CM_CTL_SRC_PLLD = (6 shl 0);`	Clock source - 750 MHz PLLD
`BCM2838_CM_CTL_SRC_HDMI = (7 shl 0);`	Clock source - Unused

BCM2838 clock manager divisor BCM2838_CM_DIV_*

See: Section 6.3

`BCM2838_CM_DIV_INT_MASK = $00FFF000;`	Integer part of divisor (This value has a minimum limit determined by the MASH setting) (To avoid lock-ups and glitches do not change this control while BUSY=1)
`BCM2838_CM_DIV_FRAC_MASK = $00000FFF;`	Fractional part of divisor (To avoid lock-ups and glitches do not change this control while BUSY=1)

BCM2838 clock manager BCM2838_CM_*

`BCM2838_CM_GNRICCTL = $00000000;`	Generic Clock Control
`BCM2838_CM_GNRICDIV = $00000004;`	Generic Clock Divisor
`BCM2838_CM_VPUCTL = $00000008;`	VPU Clock Control
`BCM2838_CM_VPUDIV = $0000000C;`	VPU Clock Divisor
`BCM2838_CM_SYSCTL = $00000010;`	System Clock Control
`BCM2838_CM_SYSDIV = $00000014;`	System Clock Divisor
`BCM2838_CM_PERIACTL = $00000018;`	PERIA Clock Control
`BCM2838_CM_PERIADIV = $0000001C;`	PERIA Clock Divisor
`BCM2838_CM_PERIICTL = $00000020;`	PERII Clock Control
`BCM2838_CM_PERIIDIV = $00000024;`	PERII Clock Divisor
`BCM2838_CM_H264CTL = $00000028;`	H264 Clock Control
`BCM2838_CM_H264DIV = $0000002C;`	H264 Clock Divisor
`BCM2838_CM_ISPCTL = $00000030;`	ISP Clock Control
`BCM2838_CM_ISPDIV = $00000034;`	ISP Clock Divisor
`BCM2838_CM_V3DCTL = $00000038;`	V3D Clock Control
`BCM2838_CM_V3DDIV = $0000003C;`	V3D Clock Divisor
`BCM2838_CM_CAM0CTL = $00000040;`	Camera 0 Clock Control
`BCM2838_CM_CAM0DIV = $00000044;`	Camera 0 Clock Divisor
`BCM2838_CM_CAM1CTL = $00000048;`	Camera 1 Clock Control
`BCM2838_CM_CAM1DIV = $0000004C;`	Camera 1 Clock Divisor
`BCM2838_CM_CCP2CTL = $00000050;`	CCP2 Clock Control
`BCM2838_CM_CCP2DIV = $00000054;`	CCP2 Clock Divisor
`BCM2838_CM_DSI0ECTL = $00000058;`	DSI0E Clock Control
`BCM2838_CM_DSI0EDIV = $0000005C;`	DSI0E Clock Divisor
`BCM2838_CM_DSI0PCTL = $00000060;`	DSI0P Clock Control
`BCM2838_CM_DSI0PDIV = $00000064;`	DSI0P Clock Divisor
`BCM2838_CM_DPICTL = $00000068;`	DPI Clock Control
`BCM2838_CM_DPIDIV = $0000006C;`	DPI Clock Divisor
`BCM2838_CM_GP0CTL = $00000070;`	General Purpose 0 Clock Control
`BCM2838_CM_GP0DIV = $00000074;`	General Purpose 0 Clock Divisor
`BCM2838_CM_GP1CTL = $00000078;`	General Purpose 1 Clock Control
`BCM2838_CM_GP1DIV = $0000007C;`	General Purpose 1 Clock Divisor
`BCM2838_CM_GP2CTL = $00000080;`	General Purpose 2 Clock Control
`BCM2838_CM_GP2DIV = $00000084;`	General Purpose 2 Clock Divisor
`BCM2838_CM_HSMCTL = $00000088;`	HSM Clock Control
`BCM2838_CM_HSMDIV = $0000008C;`	HSM Clock Divisor
`BCM2838_CM_OTPCTL = $00000090;`	OTP Clock Control
`BCM2838_CM_OTPDIV = $00000094;`	OTP Clock Divisor
`BCM2838_CM_PCMCTL = $00000098;`	PCM / I2S Clock Control
`BCM2838_CM_PCMDIV = $0000009C;`	PCM / I2S Clock Divisor
`BCM2838_CM_PWMCTL = $000000A0;`	PWM Clock Control
`BCM2838_CM_PWMDIV = $000000A4;`	PWM Clock Divisor
`BCM2838_CM_SLIMCTL = $000000A8;`	SLIM Clock Control
`BCM2838_CM_SLIMDIV = $000000AC;`	SLIM Clock Divisor
`BCM2838_CM_SMICTL = $000000B0;`	SMI Clock Control
`BCM2838_CM_SMIDIV = $000000B4;`	SMI Clock Divisor
`BCM2838_CM_TCNTCTL = $000000C0;`	TCNT Clock Control
`BCM2838_CM_TCNTDIV = $000000C4;`	TCNT Clock Divisor
`BCM2838_CM_TECCTL = $000000C8;`	TEC Clock Control
`BCM2838_CM_TECDIV = $000000CC;`	TEC Clock Divisor
`BCM2838_CM_TD0CTL = $000000D0;`	TD0 Clock Control
`BCM2838_CM_TD0DIV = $000000D4;`	TD0 Clock Divisor
`BCM2838_CM_TD1CTL = $000000D8;`	TD1 Clock Control
`BCM2838_CM_TD1DIV = $000000DC;`	TD1 Clock Divisor
`BCM2838_CM_TSENSCTL = $000000E0;`	TSENS Clock Control
`BCM2838_CM_TSENSDIV = $000000E4;`	TSENS Clock Divisor
`BCM2838_CM_TIMERCTL = $000000E8;`	Timer Clock Control
`BCM2838_CM_TIMERDIV = $000000EC;`	Timer Clock Divisor
`BCM2838_CM_UARTCTL = $000000F0;`	UART Clock Control
`BCM2838_CM_UARTDIV = $000000F4;`	UART Clock Divisor
`BCM2838_CM_VECCTL = $000000F8;`	VEC Clock Control
`BCM2838_CM_VECDIV = $000000FC;`	VEC Clock Divisor

`BCM2838_CM_OSCCOUNT = $00000100;`	Oscillator Count
`BCM2838_CM_PLLA = $00000104;`	PLLA
`BCM2838_CM_PLLC = $00000108;`	PLLC
`BCM2838_CM_PLLD = $0000010C;`	PLLD
`BCM2838_CM_PLLH = $00000110;`	PLLH
`BCM2838_CM_LOCK = $00000114;`	Lock
`BCM2838_CM_EVENT = $00000118;`	Event
`BCM2838_CM_INTEN = $00000118;`	INTEN
`BCM2838_CM_DSI0HSCK = $00000120;`	DSI0HSCK
`BCM2838_CM_CKSM = $00000124;`	CKSM
`BCM2838_CM_OSCFREQI = $00000128;`	Oscillator Frequency Integer
`BCM2838_CM_OSCFREQF = $0000012C;`	Oscillator Frequency Fraction
`BCM2838_CM_PLLTCTL = $00000130;`	PLLT Control
`BCM2838_CM_PLLTCNT0 = $00000134;`	PLLT0 Count
`BCM2838_CM_PLLTCNT1 = $00000138;`	PLLT1 Count
`BCM2838_CM_PLLTCNT2 = $0000013C;`	PLLT2 Count
`BCM2838_CM_PLLTCNT3 = $00000140;`	PLLT3 Count
`BCM2838_CM_TDCLKEN = $00000144;`	TD Clock Enable
`BCM2838_CM_BURSTCTL = $00000148;`	Burst Control
`BCM2838_CM_BURSTCNT = $0000014C;`	Burst Count
`BCM2838_CM_DSI1ECTL = $00000158;`	DSI1E Clock Control
`BCM2838_CM_DSI1EDIV = $0000015C;`	DSI1E Clock Divisor
`BCM2838_CM_DSI1PCTL = $00000160;`	DSI1P Clock Control
`BCM2838_CM_DSI1PDIV = $00000164;`	DSI1P Clock Divisor
`BCM2838_CM_DFTCTL = $00000168;`	DFT Clock Control
`BCM2838_CM_DFTDIV = $0000016C;`	DFT Clock Divisor
`BCM2838_CM_PLLB = $00000170;`	PLLB

`BCM2838_CM_PULSECTL = $00000190;`	Pulse Clock Control
`BCM2838_CM_PULSEDIV = $00000194;`	Pulse Clock Divisor
`BCM2838_CM_SDCCTL = $000001A8;`	SDC Clock Control
`BCM2838_CM_SDCDIV = $000001AC;`	SDC Clock Divisor
`BCM2838_CM_ARMCTL = $000001B0;`	ARM Clock Control
`BCM2838_CM_ARMDIV = $000001B4;`	ARM Clock Divisor
`BCM2838_CM_AVEOCTL = $000001B8;`	AVEO Clock Control
`BCM2838_CM_AVEODIV = $000001BC;`	AVEO Clock Divisor
`BCM2838_CM_EMMCCTL = $000001C0;`	EMMC Clock Control
`BCM2838_CM_EMMCDIV = $000001C4;`	EMMC Clock Divisor

BCM2838 mailbox BCM2838_MAILBOX_*

`BCM2838_MAILBOX_0 = 0;`
`BCM2838_MAILBOX_1 = 1;`

BCM2838 mailbox 0 channel BCM2838_MAILBOX0_CHANNEL_*

See: https://github.com/raspberrypi/firmware/wiki/Mailboxes

`BCM2838_MAILBOX0_CHANNEL_POWER_MGMT = 0;`
`BCM2838_MAILBOX0_CHANNEL_FRAMEBUFFER = 1;`
`BCM2838_MAILBOX0_CHANNEL_UART = 2;`
`BCM2838_MAILBOX0_CHANNEL_VCHIQ = 3;`
`BCM2838_MAILBOX0_CHANNEL_LEDS = 4;`
`BCM2838_MAILBOX0_CHANNEL_BUTTONS = 5;`
`BCM2838_MAILBOX0_CHANNEL_TOUCHSCREEN = 6;`
`BCM2838_MAILBOX0_CHANNEL_UNKNOWN = 7;`
`BCM2838_MAILBOX0_CHANNEL_PROPERTYTAGS_ARMVC = 8;`
`BCM2838_MAILBOX0_CHANNEL_PROPERTYTAGS_VCARM = 9;`

BCM2838 mailbox 1 channel BCM2838_MAILBOX_*_MASK*

See: https://github.com/raspberrypi/firmware/wiki/Mailboxes
Currently unknown

The BCM2838 mailboxes pass 28-bit messages (The low 4 bits of the 32-bit value are used to specify the channel)
`BCM2838_MAILBOX_CHANNEL_MASK = $0000000F;`
`BCM2838_MAILBOX_DATA_MASK = $FFFFFFF0;`

BCM2838 mailbox status flag BCM2838_MAILBOX_STATUS_*

`BCM2838_MAILBOX_STATUS_FULL = $80000000;`
`BCM2838_MAILBOX_STATUS_EMPTY = $40000000;`

BCM2838 mailbox configuration flag BCM2838_MAILBOX_CONFIG_*

`BCM2838_MAILBOX_CONFIG_IRQENABLE = $00000001;`

BCM2838 mailbox property tag BCM2838_MBOX_TAG_GET_*

See: https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface or \include\soc\bcm2835\raspberrypi-firmware.h

VideoCore
`BCM2838_MBOX_TAG_GET_FIRMWARE_REV = $00000001;`
Hardware
`BCM2838_MBOX_TAG_GET_BOARD_MODEL = $00010001;`
`BCM2838_MBOX_TAG_GET_BOARD_REV = $00010002;`

`BCM2838_MBOX_TAG_GET_MAC_ADDRESS = $00010003;`

`BCM2838_MBOX_TAG_GET_BOARD_SERIAL = $00010004;`

`BCM2838_MBOX_TAG_GET_ARM_MEMORY = $00010005;`
`BCM2838_MBOX_TAG_GET_VC_MEMORY = $00010006;`

`BCM2838_MBOX_TAG_GET_CLOCKS = $00010007;`
Shared Resource Management
`BCM2838_MBOX_TAG_GET_POWER_STATE = $00020001;`	Response indicates current state
`BCM2838_MBOX_TAG_GET_TIMING = $00020002;`	Response indicates wait time required after turning a device on before power is stable
`BCM2838_MBOX_TAG_SET_POWER_STATE = $00028001;`	Response indicates new state, with/without waiting for the power to become stable.

`BCM2838_MBOX_TAG_GET_CLOCK_STATE = $00030001;`
`BCM2838_MBOX_TAG_SET_CLOCK_STATE = $00038001;`

`BCM2838_MBOX_TAG_GET_CLOCK_RATE = $00030002;`
`BCM2838_MBOX_TAG_SET_CLOCK_RATE = $00038002;`

`BCM2838_MBOX_TAG_GET_CLOCK_MAX_RATE = $00030004;`	Return the maximum supported clock rate for the given clock. Clocks should not be set higher than this.
`BCM2838_MBOX_TAG_GET_CLOCK_MIN_RATE = $00030007;`	Return the minimum supported clock rate for the given clock. This may be used when idle.

`BCM2838_MBOX_TAG_GET_TURBO = $00030009;`	Get the turbo state for index id. id should be 0. level will be zero for non-turbo and one for turbo.
`BCM2838_MBOX_TAG_SET_TURBO = $00038009;`	Set the turbo state for index id. id should be zero. level will be zero for non-turbo and one for turbo. This will cause GPU clocks to be set to maximum when enabled and minimum when disabled.

`BCM2838_MBOX_TAG_GET_STC = $0003000b;`
Voltage
`BCM2838_MBOX_TAG_GET_VOLTAGE = $00030003;`	The voltage value may be clamped to the supported range. A value of 0x80000000 means the id was not valid.
`BCM2838_MBOX_TAG_SET_VOLTAGE = $00038003;`	The voltage value may be clamped to the supported range. A value of 0x80000000 means the id was not valid.

`BCM2838_MBOX_TAG_GET_MAX_VOLTAGE = $00030005;`	Return the maximum supported voltage rate for the given id. Voltages should not be set higher than this.
`BCM2838_MBOX_TAG_GET_MIN_VOLTAGE = $00030008;`	Return the minimum supported voltage rate for the given id. This may be used when idle.
`BCM2838_MBOX_TAG_GET_TEMP = $00030006;`	Return the temperature of the SoC in thousandths of a degree C. id should be zero.
`BCM2838_MBOX_TAG_GET_MAX_TEMP = $0003000a;`	Return the maximum safe temperature of the SoC in thousandths of a degree C. id should be zero. Overclock may be disabled above this temperature.
GPU
`BCM2838_MBOX_TAG_ALLOCATE_MEMORY = $0003000c;`	Allocates contiguous memory on the GPU. size and alignment are in bytes.
`BCM2838_MBOX_TAG_LOCK_MEMORY = $0003000d;`	Lock buffer in place, and return a bus address. Must be done before memory can be accessed.
`BCM2838_MBOX_TAG_UNLOCK_MEMORY = $0003000e;`	Unlock buffer. It retains contents, but may move. Needs to be locked before next use. status=0 is success.
`BCM2838_MBOX_TAG_RELEASE_MEMORY = $0003000f;`	Free the memory buffer. status=0 is success.

`BCM2838_MBOX_TAG_EXECUTE_CODE = $00030010;`	Calls the function at given (bus) address and with arguments given. E.g. r0 = fn(r0, r1, r2, r3, r4, r5); It blocks until call completes
`BCM2838_MBOX_TAG_EXECUTE_QPU = $00030011;`	Execute an assembled block of code using one or more Quad Processing Units (QPUs)
`BCM2838_MBOX_TAG_ENABLE_QPU = $00030012;`	Enable the Quad Processing Units (QPUs)

`BCM2838_MBOX_TAG_GET_DISPMANX_HANDLE = $00030014;`	Gets the mem_handle associated with a created dispmanx resource. This can be locked and the memory directly written from the arm to avoid having to copy the image data to GPU.
`BCM2838_MBOX_TAG_GET_EDID_BLOCK = $00030020;`	This reads the specified EDID block from attached HDMI/DVI device. There will always be at least one block of 128 bytes, but there may be additional blocks. You should keep requesting blocks (starting from 0) until the status returned is non-zero.

`BCM2838_MBOX_TAG_GET_CUSTOMER_OTP = $00030021;`
`BCM2838_MBOX_TAG_SET_CUSTOMER_OTP = $00038021;`

`BCM2838_MBOX_TAG_GET_DOMAIN_STATE = $00030030;`
`BCM2838_MBOX_TAG_SET_DOMAIN_STATE = $00038030;`

`BCM2838_MBOX_TAG_GET_GPIO_STATE = $00030041;`	Get the current state of a GPIO expander pin
`BCM2838_MBOX_TAG_SET_GPIO_STATE = $00038041;`	Set the current state of a GPIO expander pin

`BCM2838_MBOX_TAG_SET_SDHOST_CLOCK = $00038042;`	Tell the firmware the SD Host clock setting so it will be adjusted for changes in core frequency

`BCM2838_MBOX_TAG_GET_GPIO_CONFIG = $00030043;`	Get the current configuration of a GPIO expander pin
`BCM2838_MBOX_TAG_SET_GPIO_CONFIG = $00038043;`	Set the current configuration of a GPIO expander pin

`BCM2838_MBOX_TAG_GET_THROTTLED = $00030046;`

`BCM2838_MBOX_TAG_GET_PERIPH_REG = $00030045;`
`BCM2838_MBOX_TAG_SET_PERIPH_REG = $00038045;`
Frame Buffer
`BCM2838_MBOX_TAG_ALLOCATE_BUFFER = $00040001;`	If the requested alignment is unsupported then the current base and size (which may be 0 if not allocated) is returned and no change occurs
`BCM2838_MBOX_TAG_RELEASE_BUFFER = $00048001;`	Releases and disables the frame buffer

`BCM2838_MBOX_TAG_SET_BLANK_SCREEN = $00040002;`
`BCM2838_MBOX_TAG_TEST_BLANK_SCREEN = $00044002;`	Previously BCM2838_MBOX_TAG_TST_BLANK_SCREEN

`BCM2838_MBOX_TAG_GET_PHYSICAL_W_H = $00040003;`	Note that the "physical (display)" size is the size of the allocated buffer in memory, not the resolution of the video signal sent to the display device.
`BCM2838_MBOX_TAG_TEST_PHYSICAL_W_H = $00044003;`
`BCM2838_MBOX_TAG_SET_PHYSICAL_W_H = $00048003;`

`BCM2838_MBOX_TAG_GET_VIRTUAL_W_H = $00040004;`	Note that the "virtual (buffer)" size is the portion of buffer that is sent to the display device, not the resolution the buffer itself. This may be smaller than the allocated buffer size in order to implement panning.
`BCM2838_MBOX_TAG_TEST_VIRTUAL_W_H = $00044004;`
`BCM2838_MBOX_TAG_SET_VIRTUAL_W_H = $00048004;`

`BCM2838_MBOX_TAG_GET_DEPTH = $00040005;`
`BCM2838_MBOX_TAG_TEST_DEPTH = $00044005;`
`BCM2838_MBOX_TAG_SET_DEPTH = $00048005;`

`BCM2838_MBOX_TAG_GET_PIXEL_ORDER = $00040006;`
`BCM2838_MBOX_TAG_TEST_PIXEL_ORDER = $00044006;`
`BCM2838_MBOX_TAG_SET_PIXEL_ORDER = $00048006;`

`BCM2838_MBOX_TAG_GET_ALPHA_MODE = $00040007;`
`BCM2838_MBOX_TAG_TEST_ALPHA_MODE = $00044007;`
`BCM2838_MBOX_TAG_SET_ALPHA_MODE = $00048007;`

`BCM2838_MBOX_TAG_GET_PITCH = $00040008;`
`BCM2838_MBOX_TAG_TEST_PITCH = $00044008;`	Previously BCM2838_MBOX_TAG_TST_PITCH
`BCM2838_MBOX_TAG_SET_PITCH = $00048008;`

`BCM2838_MBOX_TAG_GET_VIRTUAL_OFFSET = $00040009;`	Offset of physical display window within virtual buffer
`BCM2838_MBOX_TAG_TEST_VIRTUAL_OFFSET = $00044009;`
`BCM2838_MBOX_TAG_SET_VIRTUAL_OFFSET = $00048009;`

`BCM2838_MBOX_TAG_GET_OVERSCAN = $0004000a;`
`BCM2838_MBOX_TAG_TEST_OVERSCAN = $0004400a;`
`BCM2838_MBOX_TAG_SET_OVERSCAN = $0004800a;`

`BCM2838_MBOX_TAG_GET_PALETTE = $0004000b;`
`BCM2838_MBOX_TAG_TEST_PALETTE = $0004400b;`
`BCM2838_MBOX_TAG_SET_PALETTE = $0004800b;`

`BCM2838_MBOX_TAG_GET_LAYER = $0004000c;`
`BCM2838_MBOX_TAG_TEST_LAYER = $0004400c;`	Previously BCM2838_MBOX_TAG_TST_LAYER
`BCM2838_MBOX_TAG_SET_LAYER = $0004800c;`

`BCM2838_MBOX_TAG_GET_TRANSFORM = $0004000d;`
`BCM2838_MBOX_TAG_TEST_TRANSFORM = $0004400d;`	Previously BCM2838_MBOX_TAG_TST_TRANSFORM
`BCM2838_MBOX_TAG_SET_TRANSFORM = $0004800d;`

`BCM2838_MBOX_TAG_TEST_VSYNC = $0004400e;`	Previously BCM2838_MBOX_TAG_TST_VSYNC
`BCM2838_MBOX_TAG_SET_VSYNC = $0004800e;`

`BCM2838_MBOX_TAG_SET_BACKLIGHT = $0004800f;`

`BCM2838_MBOX_TAG_GET_TOUCHBUF = $0004000f;`
`BCM2838_MBOX_TAG_SET_TOUCHBUF = $0004801f;`

`BCM2838_MBOX_TAG_GET_GPIOVIRTBUF = $00040010;`
`BCM2838_MBOX_TAG_SET_GPIOVIRTBUF = $00048020;`

`BCM2838_MBOX_TAG_GET_DISPLAY_ID = $00040016;`
`BCM2838_MBOX_TAG_SET_DISPLAY_NUM = $00048013;`
`BCM2838_MBOX_TAG_GET_NUM_DISPLAYS = $00040013;`
`BCM2838_MBOX_TAG_GET_DISPLAY_SETTINGS = $00040014;`

`BCM2838_MBOX_TAG_SET_PLANE = $00048015;`
`BCM2838_MBOX_TAG_GET_DISPLAY_TIMING = $00040017;`
`BCM2838_MBOX_TAG_SET_TIMING = $00048017;`
`BCM2838_MBOX_TAG_GET_DISPLAY_CFG = $00040018;`
`BCM2838_MBOX_TAG_SET_DISPLAY_POWER = $00048019;`

`BCM2838_MBOX_TAG_SET_CURSOR_INFO = $00008010;`	00008011 These were reversed in the documentation, see Linux \include\soc\bcm2835\raspberrypi-firmware.h
`BCM2838_MBOX_TAG_SET_CURSOR_STATE = $00008011;`	00008010
VCHIQ
`BCM2838_MBOX_TAG_VCHIQ_INIT = $00048010;`
Config
`BCM2838_MBOX_TAG_GET_COMMAND_LINE = $00050001;`
Shared Resource Management
`BCM2838_MBOX_TAG_GET_DMA_CHANNELS = $00060001;`	Caller assumes that the VC has enabled all the usable DMA channels
End
`BCM2838_MBOX_TAG_END = $00000000;`

BCM2838 mailbox board revision value BCM2838_BOARD_REV_*

See: http://elinux.org/RPi_HardwareHistory

`BCM2838_BOARD_REV_2B_1 = $00A01041;`
`BCM2838_BOARD_REV_2B_2 = $00A21041;`
`BCM2838_BOARD_REV_2B_3 = $00A22042;`

`BCM2838_BOARD_REV_3B_1 = $00A02082;`
`BCM2838_BOARD_REV_3B_2 = $00A22082;`
`BCM2838_BOARD_REV_3B_3 = $00A32082;`

`BCM2838_BOARD_REV_CM3_1 = $00A020A0;`
`BCM2838_BOARD_REV_CM3_2 = $00A220A0;`

`BCM2838_BOARD_REV_MASK = $00FFFFFF;`	Mask off the warranty bit

BCM2838 mailbox board revision BCM2838_BOARD_REVISION_*

See: https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md

`BCM2838_BOARD_REVISION_PCB_MASK = ($F shl 0);`	PCB Revision Number

`BCM2838_BOARD_REVISION_MODEL_MASK = ($FF shl 4);`	Model Number
`BCM2838_BOARD_REVISION_MODEL_A = (0 shl 4);`	Model A (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_B = (1 shl 4);`	Model B (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_APLUS = (2 shl 4);`	Model A+ (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_BPLUS = (3 shl 4);`	Model B+ (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_2B = (4 shl 4);`	Model 2B (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_ALPHA = (5 shl 4);`	Unknown
`BCM2838_BOARD_REVISION_MODEL_COMPUTE = (6 shl 4);`	Compute Module (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_UNKNOWN = (7 shl 4);`	Unknown
`BCM2838_BOARD_REVISION_MODEL_3B = (8 shl 4);`	Model 3B (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_ZERO = (9 shl 4);`	Model Zero (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_COMPUTE3 = (10 shl 4);`	Compute Module 3 (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_UNKNOWN_2 = (11 shl 4);`	Unknown
`BCM2838_BOARD_REVISION_MODEL_ZERO_W = (12 shl 4);`	Model Zero W (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_3BPLUS = (13 shl 4);`	Model 3B+ (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_3APLUS = (14 shl 4);`	Model 3A+ (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_COMPUTE3PLUS = (16 shl 4);`	Compute Module 3+ (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_MODEL_4B = (17 shl 4);`	Model 4B
`BCM2838_BOARD_REVISION_MODEL_400 = (19 shl 4);`	Pi 400
`BCM2838_BOARD_REVISION_MODEL_CM4 = (20 shl 4);`	Compute Module 4

`BCM2838_BOARD_REVISION_PROCESSOR_MASK = ($F shl 12);`	Processor Type
`BCM2838_BOARD_REVISION_PROCESSOR_BCM2835 = (0 shl 12);`	BCM2835 (Cannot occur on BCM2838)
`BCM2838_BOARD_REVISION_PROCESSOR_BCM2836 = (1 shl 12);`	BCM2836
`BCM2838_BOARD_REVISION_PROCESSOR_BCM2837 = (2 shl 12);`	BCM2837
`BCM2838_BOARD_REVISION_PROCESSOR_BCM2838 = (3 shl 12);`	BCM2838

`BCM2838_BOARD_REVISION_MANUFACTURER_MASK = ($F shl 16);`	Manufacturer
`BCM2838_BOARD_REVISION_MANUFACTURER_SONY = (0 shl 16);`	Sony
`BCM2838_BOARD_REVISION_MANUFACTURER_EGOMAN = (1 shl 16);`	Egoman
`BCM2838_BOARD_REVISION_MANUFACTURER_EMBEST = (2 shl 16);`	Embest
`BCM2838_BOARD_REVISION_MANUFACTURER_SONY_JAPAN = (3 shl 16);`	Sony (Japan)
`BCM2838_BOARD_REVISION_MANUFACTURER_EMBEST2 = (4 shl 16);`	Embest
`BCM2838_BOARD_REVISION_MANUFACTURER_STADIUM = (5 shl 16);`	Stadium

`BCM2838_BOARD_REVISION_MEMORY_MASK = ($7 shl 20);`	Memory Size
`BCM2838_BOARD_REVISION_MEMORY_256M = (0 shl 20);`	256M
`BCM2838_BOARD_REVISION_MEMORY_512M = (1 shl 20);`	512M
`BCM2838_BOARD_REVISION_MEMORY_1024M = (2 shl 20);`	1024M
`BCM2838_BOARD_REVISION_MEMORY_2048M = (3 shl 20);`	2048M
`BCM2838_BOARD_REVISION_MEMORY_4096M = (4 shl 20);`	4096M
`BCM2838_BOARD_REVISION_MEMORY_8192M = (5 shl 20);`	8192M

`BCM2838_BOARD_REVISION_ENCODED_FLAG = (1 shl 23);`	Encoded Flag, if set then revision uses this encoding.

`BCM2838_BOARD_REVISION_MASK = $00FFFFFF;`	Mask off the warranty bits

BCM2838 mailbox tag power state device BCM2838_MBOX_POWER_DEVID_*

`BCM2838_MBOX_POWER_DEVID_SDHCI = 0;`
`BCM2838_MBOX_POWER_DEVID_UART0 = 1;`
`BCM2838_MBOX_POWER_DEVID_UART1 = 2;`
`BCM2838_MBOX_POWER_DEVID_USB_HCD = 3;`
`BCM2838_MBOX_POWER_DEVID_I2C0 = 4;`
`BCM2838_MBOX_POWER_DEVID_I2C1 = 5;`
`BCM2838_MBOX_POWER_DEVID_I2C2 = 6;`
`BCM2838_MBOX_POWER_DEVID_SPI = 7;`
`BCM2838_MBOX_POWER_DEVID_CCP2TX = 8;`

`BCM2838_MBOX_POWER_DEVID_UNKNOWN = $FFFFFFFF;`

BCM2838 mailbox tag power state request BCM2838_MBOX_SET_POWER_STATE_REQ_*

`BCM2838_MBOX_SET_POWER_STATE_REQ_OFF = (0 shl 0);`
`BCM2838_MBOX_SET_POWER_STATE_REQ_ON = (1 shl 0);`
`BCM2838_MBOX_SET_POWER_STATE_REQ_WAIT = (1 shl 1);`

BCM2838 mailbox tag power state response BCM2838_MBOX_POWER_STATE_RESP_*

`BCM2838_MBOX_POWER_STATE_RESP_OFF = (0 shl 0);`
`BCM2838_MBOX_POWER_STATE_RESP_ON = (1 shl 0);`
`BCM2838_MBOX_POWER_STATE_RESP_NODEV = (1 shl 1);`	Device doesn't exist

BCM2838 mailbox tag clock state/rate id BCM2838_MBOX_CLOCK_ID_*

`BCM2838_MBOX_CLOCK_ID_RESERVED = 0;`
`BCM2838_MBOX_CLOCK_ID_EMMC = 1;`
`BCM2838_MBOX_CLOCK_ID_UART = 2;`
`BCM2838_MBOX_CLOCK_ID_ARM = 3;`
`BCM2838_MBOX_CLOCK_ID_CORE = 4;`
`BCM2838_MBOX_CLOCK_ID_V3D = 5;`
`BCM2838_MBOX_CLOCK_ID_H264 = 6;`
`BCM2838_MBOX_CLOCK_ID_ISP = 7;`
`BCM2838_MBOX_CLOCK_ID_SDRAM = 8;`
`BCM2838_MBOX_CLOCK_ID_PIXEL = 9;`
`BCM2838_MBOX_CLOCK_ID_PWM = 10;`
`BCM2838_MBOX_CLOCK_ID_HEVC = 11;`
`BCM2838_MBOX_CLOCK_ID_EMMC2 = 12;`
`BCM2838_MBOX_CLOCK_ID_M2MC = 13;`
`BCM2838_MBOX_CLOCK_ID_PIXEL_BVB = 14;`

`BCM2838_MBOX_CLOCK_ID_UNKNOWN = $FFFFFFFF;`

BCM2838 mailbox tag clock state request BCM2838_MBOX_SET_CLOCK_STATE__REQ_*

`BCM2838_MBOX_SET_CLOCK_STATE_REQ_OFF = (0 shl 0);`
`BCM2838_MBOX_SET_CLOCK_STATE_REQ_ON = (1 shl 0);`
`BCM2838_MBOX_SET_CLOCK_STATE_REQ_NOCLOCK = (1 shl 1);`	Clock doesn't exist

BCM2838 mailbox tag clock state response BCM2838_MBOX_CLOCK_STATE_RESP_ *

`BCM2838_MBOX_CLOCK_STATE_RESP_OFF = (0 shl 0);`
`BCM2838_MBOX_CLOCK_STATE_RESP_ON = (1 shl 0);`
`BCM2838_MBOX_CLOCK_STATE_RESP_NOCLOCK = (1 shl 1);`	Clock doesn't exist

BCM2838 mailbox tag clock rate turbo BCM2838_MBOX_CLOCK_RATE_*

`BCM2838_MBOX_CLOCK_RATE_REQ_SKIP_TURBO = (1 shl 0);`

BCM2838 mailbox tag voltage id BCM2838_MBOX_VOLTAGE_ID_*

`BCM2838_MBOX_VOLTAGE_ID_RESERVED = $00000000;`
`BCM2838_MBOX_VOLTAGE_ID_CORE = $00000001;`
`BCM2838_MBOX_VOLTAGE_ID_SDRAM_C = $00000002;`
`BCM2838_MBOX_VOLTAGE_ID_SDRAM_P = $00000003;`
`BCM2838_MBOX_VOLTAGE_ID_SDRAM_I = $00000004;`

BCM2838 mailbox tag voltage BCM2838_MBOX_VOLTAGE_*

`BCM2838_MBOX_VOLTAGE_INVALID = $80000000;`	A value of 0x80000000 means the id was not valid

BCM2838 mailbox tag temperature id BCM2838_MBOX_TEMP_ID_*

`BCM2838_MBOX_TEMP_ID_SOC = 0;`

BCM2838 mailbox display id BCM2838_MBOX_DISPLAY_ID_*

Note: These are compatible with the DISPMANX_ID_* values

`BCM2838_MBOX_DISPLAY_ID_MAIN_LCD = 0;`
`BCM2838_MBOX_DISPLAY_ID_AUX_LCD = 1;`
`BCM2838_MBOX_DISPLAY_ID_HDMI0 = 2;`
`BCM2838_MBOX_DISPLAY_ID_SDTV = 3;`
`BCM2838_MBOX_DISPLAY_ID_FORCE_LCD = 4;`
`BCM2838_MBOX_DISPLAY_ID_FORCE_TV = 5;`
`BCM2838_MBOX_DISPLAY_ID_FORCE_OTHER = 6;`	Non-default display
`BCM2838_MBOX_DISPLAY_ID_HDMI1 = 7;`
`BCM2838_MBOX_DISPLAY_ID_FORCE_TV2 = 8;`

BCM2838 mailbox tag memory flag BCM2838_MBOX_MEM_FLAG_*

`BCM2838_MBOX_MEM_FLAG_DISCARDABLE = (1 shl 0);`	Can be resized to 0 at any time. Use for cached data.
`BCM2838_MBOX_MEM_FLAG_NORMAL = (0 shl 2);`	Normal allocating alias. Don't use from ARM.
`BCM2838_MBOX_MEM_FLAG_DIRECT = (1 shl 2);`	0xC alias uncached
`BCM2838_MBOX_MEM_FLAG_COHERENT = (2 shl 2);`	0x8 alias. Non-allocating in L2 but coherent
`BCM2838_MBOX_MEM_FLAG_L1_NONALLOCATING = (BCM2838_MBOX_MEM_FLAG_DIRECT or BCM2838_MBOX_MEM_FLAG_COHERENT);`	Allocating in L2
`BCM2838_MBOX_MEM_FLAG_ZERO = (1 shl 4);`	Initialise buffer to all zeros
`BCM2838_MBOX_MEM_FLAG_NO_INIT = (1 shl 5);`	Don't initialise (default is initialise to all ones)
`BCM2838_MBOX_MEM_FLAG_HINT_PERMALOCK = (1 shl 6);`	Likely to be locked for long periods of time

BCM2838 mailbox tag blank screen BCM2838_MBOX_BLANK_SCREEN_*

`BCM2838_MBOX_BLANK_SCREEN_REQ_ON = (1 shl 0);`

BCM2838 mailbox tag pixel order BCM2838_MBOX_PIXEL_ORDER_*

`BCM2838_MBOX_PIXEL_ORDER_BGR = 0;`
`BCM2838_MBOX_PIXEL_ORDER_RGB = 1;`

BCM2838 mailbox tag alpha mode BCM2838_MBOX_ALPHA_MODE_*

`BCM2838_MBOX_ALPHA_MODE_0_OPAQUE = 0;`
`BCM2838_MBOX_ALPHA_MODE_0_TRANSPARENT = 1;`
`BCM2838_MBOX_ALPHA_MODE_IGNORED = 2;`

BCM2838 mailbox tag palette BCM2838_MBOX_PALETTE_*

`BCM2838_MBOX_PALETTE_INVALID = $00000001;`

BCM2838 mailbox tag cursor state BCM2838_MBOX_CURSOR_*

`BCM2838_MBOX_CURSOR_INVISIBLE = 0;`
`BCM2838_MBOX_CURSOR_VISIBLE = 1;`

BCM2838 mailbox tag cursor state flag BCM2838_MBOX_CURSOR_STATE_*

`BCM2838_MBOX_CURSOR_STATE_DISPLAY_COORDS = (0 shl 0);`
`BCM2838_MBOX_CURSOR_STATE_FRAMEBUFFER_COORDS = (1 shl 0);`

BCM2838 mailbox tag cursor BCM2838_MBOX_CURSOR_INVALID*

`BCM2838_MBOX_CURSOR_INVALID = $00000001;`

BCM2838 mailbox request/response BCM2838_MBOX_REQUEST_*

`BCM2838_MBOX_REQUEST_CODE = $00000000;`
`BCM2838_MBOX_RESPONSE_CODE_SUCCESS = $80000000;`
`BCM2838_MBOX_RESPONSE_CODE_ERROR = $80000001;`

BCM2838 mailbox tag request/response BCM2838_MBOX_TAG_REQUEST_*

`BCM2838_MBOX_TAG_REQUEST_CODE = $00000000;`
`BCM2838_MBOX_TAG_RESPONSE_CODE = $80000000;`

BCM2838 GPIO BCM2838_GPIO_*

`BCM2838_GPIO_PIN_COUNT = 58;`
`BCM2838_GPIO_BANK_COUNT = 2;`

`BCM2838_GPIO_SIGNATURE = $6770696F;`	The ASCII value 'GPIO' returned when reading from a write only register

BCM2838 virtual GPIO BCM2838_VIRTUAL_GPIO_*

`BCM2838_VIRTUAL_GPIO_PIN_COUNT = 2;`	Raspberry Pi 4B only

BCM2838 function select register BCM2838_GP*

`BCM2838_GPFSEL0 = $00000000;`	GPIO Function Select 0
`BCM2838_GPFSEL1 = $00000004;`	GPIO Function Select 1
`BCM2838_GPFSEL2 = $00000008;`	GPIO Function Select 2
`BCM2838_GPFSEL3 = $0000000C;`	GPIO Function Select 3
`BCM2838_GPFSEL4 = $00000010;`	GPIO Function Select 4
`BCM2838_GPFSEL5 = $00000014;`	GPIO Function Select 5

Pin Output Set Registers
`BCM2838_GPSET0 = $0000001C;`	GPIO Pin Output Set 0
`BCM2838_GPSET1 = $00000020;`	GPIO Pin Output Set 1

Pin Output Clear Registers
`BCM2838_GPCLR0 = $00000028;`	GPIO Pin Output Clear 0
`BCM2838_GPCLR1 = $0000002C;`	GPIO Pin Output Clear 1

Pin Level Registers
`BCM2838_GPLEV0 = $00000034;`	GPIO Pin Level 0
`BCM2838_GPLEV1 = $00000038;`	GPIO Pin Level 1

Pin Event Detect Status Registers
`BCM2838_GPEDS0 = $00000040;`	GPIO Pin Event Detect Status 0
`BCM2838_GPEDS1 = $00000044;`	GPIO Pin Event Detect Status 1

Pin Rising Edge Detect Enable Registers
`BCM2838_GPREN0 = $0000004c;`	GPIO Pin Rising Edge Detect Enable 0
`BCM2838_GPREN1 = $00000050;`	GPIO Pin Rising Edge Detect Enable 1

Pin Falling Edge Detect Enable Registers
`BCM2838_GPFEN0 = $00000058;`	GPIO Pin Falling Edge Detect Enable 0
`BCM2838_GPFEN1 = $0000005c;`	GPIO Pin Falling Edge Detect Enable 1

Pin High Detect Enable Registers
`BCM2838_GPHEN0 = $00000064;`	GPIO Pin High Detect Enable 0
`BCM2838_GPHEN1 = $00000068;`	GPIO Pin High Detect Enable 1

Pin Low Detect Enable Registers
`BCM2838_GPLEN0 = $00000070;`	GPIO Pin Low Detect Enable 0
`BCM2838_GPLEN1 = $00000074;`	GPIO Pin Low Detect Enable 1

Pin Async. Rising Edge Detect Registers
`BCM2838_GPAREN0 = $0000007c;`	GPIO Pin Async. Rising Edge Detect 0
`BCM2838_GPAREN1 = $00000080;`	GPIO Pin Async. Rising Edge Detect 1

Pin Async. Falling Edge Detect Registers
`BCM2838_GPAFEN0 = $00000088;`	GPIO Pin Async. Falling Edge Detect 0
`BCM2838_GPAFEN1 = $0000008c;`	GPIO Pin Async. Falling Edge Detect 1

Pin Mux Register (See: https://github.com/raspberrypi/documentation/issues/1209)
`BCM2838_GPPINMUX = $000000D0;`

Pin Pull-up/down Mode Registers
`BCM2838_GPPUD0 = $000000E4;`	GPIO Pin Pull-up/down Mode 0
`BCM2838_GPPUD1 = $000000E8;`	GPIO Pin Pull-up/down Mode 1
`BCM2838_GPPUD2 = $000000EC;`	GPIO Pin Pull-up/down Mode 2
`BCM2838_GPPUD3 = $000000F0;`	GPIO Pin Pull-up/down Mode 3

Function Select Mask
`BCM2838_GPFSEL_MASK = 7;`

Function Select Values
`BCM2838_GPFSEL_IN = 0;`
`BCM2838_GPFSEL_OUT = 1;`
`BCM2838_GPFSEL_ALT0 = 4;`
`BCM2838_GPFSEL_ALT1 = 5;`
`BCM2838_GPFSEL_ALT2 = 6;`
`BCM2838_GPFSEL_ALT3 = 7;`
`BCM2838_GPFSEL_ALT4 = 3;`
`BCM2838_GPFSEL_ALT5 = 2;`

Pin Output Set Mask
`BCM2838_GPSET_MASK = 1;`

Pin Output Clear Mask
`BCM2838_GPCLR_MASK = 1;`

Pin Level Mask
`BCM2838_GPLEV_MASK = 1;`

Pin Event Detect Status Mask
`BCM2838_GPEDS_MASK = 1;`

Pin Rising Edge Detect Enable Mask
`BCM2838_GPREN_MASK = 1;`

Pin Falling Edge Detect Enable Mask
`BCM2838_GPFEN_MASK = 1;`

Pin High Detect Enable Mask
`BCM2838_GPHEN_MASK = 1;`

Pin Low Detect Enable Mask
`BCM2838_GPLEN_MASK = 1;`

Pin Async. Rising Edge Detect Mask
`BCM2838_GPAREN_MASK = 1;`

Pin Async. Falling Edge Detect Mask
`BCM2838_GPAFEN_MASK = 1;`

Pull-up/down Mode Mask
`BCM2838_GPPUD_MASK = 3;`

Pull-up/down Mode Values
`BCM2838_GPPUD_NONE = 0;`
`BCM2838_GPPUD_UP = 1;`
`BCM2838_GPPUD_DOWN = 2;`

Pin Mux Values
`BCM2838_GPPINMUX_RGMII_PHY_GPIO = 1;`	If set enables the RGMII PHY signals onto GPIOs 46+
`BCM2838_GPPINMUX_LEGACY_EMMC = 2;`	If set legacy EMMC controller (Arasan SD) is connected to the SD card socket

BCM2838 ARM local BCM2838_ARM_LOCAL_*

`BCM2838_ARM_LOCAL_BASE = $FF800000;`
`BCM2838_ARM_LOCAL_SIZE = SIZE_8M;`

BCM2838 ARM local peripheral BCM2838_ARM_*_REGS_ BASE*

See: BCM2711 ARM Peripherals

`BCM2838_ARM_LOCAL_REGS_BASE = (BCM2838_ARM_LOCAL_BASE + $0000);`

GICv2
`BCM2838_GICDIST_REGS_BASE = BCM2838_ARM_LOCAL_BASE + $41000;`
`BCM2838_GICCPU_REGS_BASE = BCM2838_ARM_LOCAL_BASE + $42000;`

BCM2838 IRQ local ARM peripheral BCM2838_IRQ_LOCAL_ARM_*

See: BCM2711 ARM Peripherals

ARM Generic Timers
`BCM2838_IRQ_LOCAL_ARM_CNTPSIRQ = BCM2838_IRQ_TIMER0;`
`BCM2838_IRQ_LOCAL_ARM_CNTPNSIRQ = BCM2838_IRQ_TIMER1;`
`BCM2838_IRQ_LOCAL_ARM_CNTVIRQ = BCM2838_IRQ_TIMER2;`
`BCM2838_IRQ_LOCAL_ARM_CNTHPIRQ = BCM2838_IRQ_TIMER3;`
ARM Malboxes0-3
`BCM2838_IRQ_LOCAL_ARM_MAILBOX0:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX0_0, BCM2838_IRQ_MAILBOX0_1, BCM2838_IRQ_MAILBOX0_2, BCM2838_IRQ_MAILBOX0_3);`

`BCM2838_IRQ_LOCAL_ARM_MAILBOX1:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX1_0, BCM2838_IRQ_MAILBOX1_1, BCM2838_IRQ_MAILBOX1_2, BCM2838_IRQ_MAILBOX1_3);`

`BCM2838_IRQ_LOCAL_ARM_MAILBOX2:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX2_0, BCM2838_IRQ_MAILBOX2_1, BCM2838_IRQ_MAILBOX2_2, BCM2838_IRQ_MAILBOX2_3);`

`BCM2838_IRQ_LOCAL_ARM_MAILBOX3:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX3_0, BCM2838_IRQ_MAILBOX3_1, BCM2838_IRQ_MAILBOX3_2, BCM2838_IRQ_MAILBOX3_3);`
ARM Performance Monitoring
`BCM2838_IRQ_LOCAL_ARM_PMU:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_PMU0, BCM2838_IRQ_PMU1, BCM2838_IRQ_PMU2, BCM2838_IRQ_PMU3);`
AXI Outstanding
`BCM2838_IRQ_LOCAL_ARM_AXIQUIET = BCM2838_IRQ_LOCAL_AXIQUIET;`
ARM Local Timer
`BCM2838_IRQ_LOCAL_ARM_TIMER = BCM2838_IRQ_LOCAL_TIMER;`
AXI Error
`BCM2838_IRQ_LOCAL_ARM_AXIERR = BCM2838_IRQ_LOCAL_AXIERR;`

BCM2838 ARM local control BCM2838_ARM_LOCAL_CONTROL_*

See: Table 103 ARM_CONTROL register

`BCM2838_ARM_LOCAL_CONTROL_AXIERRIRQ_DIS = (1 shl 6);`	Masks the AXI Error interrupt
`BCM2838_ARM_LOCAL_CONTROL_AXIERRIRQ_EN = (0 shl 6);`	Enables the AXI Error interrupt
`BCM2838_ARM_LOCAL_CONTROL_APB_CLOCK = (1 shl 7);`	64-bit Core timer runs from the APB clock
`BCM2838_ARM_LOCAL_CONTROL_CRYSTAL_CLOCK = (0 shl 7);`	64-bit Core timer runs from the Crystal clock
`BCM2838_ARM_LOCAL_CONTROL_INCREMENT_2 = (1 shl 8);`	64-bit Core timer increments by 2
`BCM2838_ARM_LOCAL_CONTROL_INCREMENT_1 = (0 shl 8);`	64-bit Core timer increments by 1

BCM2838 ARM local core interrupt routing BCM2838_ARM_LOCAL_AXI_ERR_ *

See: Table 104 CORE_IRQ_CONTROL Register

`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ0 = (0 shl 4);`	AXI_ERR IRQ goes to IRQ input of core 0
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ1 = (1 shl 4);`	AXI_ERR IRQ goes to IRQ input of core 1
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ2 = (2 shl 4);`	AXI_ERR IRQ goes to IRQ input of core 2
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ3 = (3 shl 4);`	AXI_ERR IRQ goes to IRQ input of core 3
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ0 = (4 shl 4);`	AXI_ERR FIQ goes to FIQ input of core 0
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ1 = (5 shl 4);`	AXI_ERR FIQ goes to FIQ input of core 1
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ2 = (6 shl 4);`	AXI_ERR FIQ goes to FIQ input of core 2
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ3 = (7 shl 4);`	AXI_ERR FIQ goes to FIQ input of core 3

`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_MASK = (7 shl 4);`
`BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_SHIFT = 4;`

BCM2838 ARM local PM interrupt routing set/clear BCM2838_ARM_LOCAL_PM_INT_ROUTING_*

See: Table 105/106 PMU_CONTROL_SET/CLR Register

`BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ0 = (1 shl 0);`	Core 0 PM IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ1 = (1 shl 1);`	Core 1 PM IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ2 = (1 shl 2);`	Core 2 PM IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ3 = (1 shl 3);`	Core 3 PM IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ0 = (1 shl 4);`	Core 0 PM FIQ Enable (If set, this bit overrides the IRQ bit 0)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ1 = (1 shl 5);`	Core 1 PM FIQ Enable (If set, this bit overrides the IRQ bit 1)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ2 = (1 shl 6);`	Core 2 PM FIQ Enable (If set, this bit overrides the IRQ bit 2)
`BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ3 = (1 shl 7);`	Core 3 PM FIQ Enable (If set, this bit overrides the IRQ bit 3)

BCM2838 ARM local peripheral interrupt routing BCM2838_ARM_LOCAL_*

See: Table 107 PERI_IRQ_ROUTE0 Register

`BCM2838_ARM_LOCAL_PERIPHERAL_WRITE_MASKS = ($01 shl 24);`	This field must be written with 0x01, otherwise changes to LOCAL_TIMER_IRQ will be ignored.

`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ0 = (0 shl 0);`	Local timer interrupt goes to Core 0 IRQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ1 = (1 shl 0);`	Local timer interrupt goes to Core 1 IRQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ2 = (2 shl 0);`	Local timer interrupt goes to Core 2 IRQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ3 = (3 shl 0);`	Local timer interrupt goes to Core 3 IRQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ0 = (4 shl 0);`	Local timer interrupt goes to Core 0 FIQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ1 = (5 shl 0);`	Local timer interrupt goes to Core 1 FIQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ2 = (6 shl 0);`	Local timer interrupt goes to Core 2 FIQ
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ3 = (7 shl 0);`	Local timer interrupt goes to Core 3 FIQ

`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_MASK = (7 shl 0);`
`BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_SHIFT = 0;`

BCM2838 ARM local AXI outstanding count BCM2838_ARM_LOCAL_AXI_COUNT_*

`BCM2838_ARM_LOCAL_AXI_COUNT_READ_MASK = ($3FF shl 0);`	Outstanding reads counter
`BCM2838_ARM_LOCAL_AXI_COUNT_WRITE_MASK = ($3FF shl 16);`	Outstanding writes counter

BCM2838 ARM local AXI outstanding IRQ BCM2838_ARM_LOCAL_AXI_QUIET_*

See: Table 108 AXI_QUIET_TIME Register
Core 0 Only

`BCM2838_ARM_LOCAL_AXI_QUIET_IRQ_ENABLE = (1 shl 20);`
`BCM2838_ARM_LOCAL_AXI_QUIET_IRQ_TIMEOUT = ($FFFFF shl 0);`

BCM2838 ARM local timer control BCM2838_ARM_LOCAL_TIMER_CONTROL_*

See: Table 109 LOCAL_TIMER_CONTROL Register

`BCM2838_ARM_LOCAL_TIMER_CONTROL_INT_STATUS = (1 shl 31);`	Interrupt flag (Read Only)
`BCM2838_ARM_LOCAL_TIMER_CONTROL_INT_ENABLE = (1 shl 29);`	Interrupt enable (1= enabled)
`BCM2838_ARM_LOCAL_TIMER_CONTROL_ENABLE = (1 shl 28);`	Timer enable (1 = enabled)
`BCM2838_ARM_LOCAL_TIMER_CONTROL_VALUE_MASK = ($0FFFFFFF shl 0);`	Re-load value

BCM2838 ARM local timer clear reload BCM2838_ARM_LOCAL_TIMER_CLEAR_*

See: Table 110 LOCAL_TIMER_IRQ Register
Write Only

`BCM2838_ARM_LOCAL_TIMER_CLEAR_INT = (1 shl 31);`	Interrupt flag clear when written as 1 (Write Only)
`BCM2838_ARM_LOCAL_TIMER_CLEAR_RELOAD = (1 shl 30);`	Local timer reloaded when written as 1 (Write Only)

BCM2838 ARM local timer interrupt control BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_*

See: Table 111 TIMER_CNTRL0, TIMER_CNTRL1, TIMER_CNTRL2 & TIMER_CNTRL3 Registers
Note: These are the ARM Generic Timers (See ARM Architecture Reference Manual)

`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPSIRQ = (1 shl 0);`	Physical Secure Timer IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPNSIRQ = (1 shl 1);`	Physical Non Secure Timer IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTHPIRQ = (1 shl 2);`	Hypervisor Timer IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTVIRQ = (1 shl 3);`	Virtual Timer IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPSFIQ = (1 shl 4);`	Physical Secure Timer FIQ Enable (If set, this bit overrides the IRQ bit 0)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPNSFIQ = (1 shl 5);`	Physical Non Secure Timer FIQ Enable (If set, this bit overrides the IRQ bit 1)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTHPFIQ = (1 shl 6);`	Hypervisor Timer FIQ Enable (If set, this bit overrides the IRQ bit 2)
`BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTVFIQ = (1 shl 7);`	Virtual Timer FIQ Enable (If set, this bit overrides the IRQ bit 3)

BCM2838 ARM local mailbox interrupt control BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_*

See: Table 112 MAILBOX_CNTRL0, MAILBOX_CNTRL1, MAILBOX_CNTRL2 & MAILBOX_CNTRL3 Registers

`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX0IRQ = (1 shl 0);`	Mailbox-0 IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX1IRQ = (1 shl 1);`	Mailbox-1 IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX2IRQ = (1 shl 2);`	Mailbox-2 IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX3IRQ = (1 shl 3);`	Mailbox-3 IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX0FIQ = (1 shl 0);`	Mailbox-0 FIQ Enable (If set, this bit overrides the IRQ bit 0)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX1FIQ = (1 shl 0);`	Mailbox-1 FIQ Enable (If set, this bit overrides the IRQ bit 1)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX2FIQ = (1 shl 0);`	Mailbox-2 FIQ Enable (If set, this bit overrides the IRQ bit 2)
`BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX3FIQ = (1 shl 0);`	Mailbox-3 FIQ Enable (If set, this bit overrides the IRQ bit 3)

BCM2838 ARM local IRQ source BCM2838_ARM_LOCAL_IRQ_SOURCE_*

See: Table 113 IRQ_SOURCE0, IRQ_SOURCE1, IRQ_SOURCE2 & IRQ_SOURCE3 Registers

`BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTPSIRQ = (1 shl 0);`	Physical Secure Timer Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTPNSIRQ = (1 shl 1);`	Physical Non Secure Timer Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTHPIRQ = (1 shl 2);`	Hypervisor Timer Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTVIRQ = (1 shl 3);`	Virtual Timer Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX0 = (1 shl 4);`	Mailbox 0 Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX1 = (1 shl 5);`	Mailbox 1 Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX2 = (1 shl 6);`	Mailbox 2 Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX3 = (1 shl 7);`	Mailbox 3 Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_GPU = (1 shl 8);`	VideoCore Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_PMU = (1 shl 9);`	Performance Monitor Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_AXI_QUIET = (1 shl 10);`	AXI Outstanding Interrupt (Core 0 Only)
`BCM2838_ARM_LOCAL_IRQ_SOURCE_TIMER = (1 shl 11);`	Local Timer Interrupt
`BCM2838_ARM_LOCAL_IRQ_SOURCE_AXI_ERR = (1 shl 30);`	AXI error, as reported by the ARM L2 cache

BCM2838 ARM local FIQ source BCM2838_ARM_LOCAL_FIQ_SOURCE_*

See: Table 114 FIQ_SOURCE0, FIQ_SOURCE1, FIQ_SOURCE2 & FIQ_SOURCE3 Registers

`BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTPSIRQ = (1 shl 0);`	Physical Secure Timer Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTPNSIRQ = (1 shl 1);`	Physical Non Secure Timer Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTHPIRQ = (1 shl 2);`	Hypervisor Timer Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTVIRQ = (1 shl 3);`	Virtual Timer Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX0 = (1 shl 4);`	Mailbox 0 Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX1 = (1 shl 5);`	Mailbox 1 Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX2 = (1 shl 6);`	Mailbox 2 Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX3 = (1 shl 7);`	Mailbox 3 Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_GPU = (1 shl 8);`	VideoCore Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_PMU = (1 shl 9);`	Performance Monitor Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_TIMER = (1 shl 11);`	Local Timer Fast Interrupt
`BCM2838_ARM_LOCAL_FIQ_SOURCE_AXI_ERR = (1 shl 30);`	AXI error, as reported by the ARM L2 cache

Type definitions

BCM2838 system timer registers

PBCM2838SystemTimerRegisters = ^TBCM2838SystemTimerRegisters;

TBCM2838SystemTimerRegisters = record

Note: Layout of the BCM2838 System Timer registers
`CS:LongWord;`	System Timer Control/Status
`CLO:LongWord;`	System Timer Counter Lower 32 bits
`CHI:LongWord;`	System Timer Counter Higher 32 bits
`C0:LongWord;`	System Timer Compare 0. Already used by the VideoCore GPU (Do not use)
`C1:LongWord;`	System Timer Compare 1
`C2:LongWord;`	System Timer Compare 2. Already used by the VideoCore GPU (Do not use)
`C3:LongWord;`	System Timer Compare 3

BCM2838 DMA channel registers

PBCM2838DMARegisters = ^TBCM2838DMARegisters;

TBCM2838DMARegisters = record

Note: Layout of the BCM2838 DMA Channel registers
`CS:LongWord;`	DMA Channel Control and Status
`CONBLK_AD:LongWord;`	DMA Channel Control Block Address
`TI:LongWord;`	DMA Channel CB Word 0 (Transfer Information)
`SOURCE_AD:LongWord;`	DMA Channel CB Word 1 (Source Address)
`DEST_AD:LongWord;`	DMA Channel CB Word 2 (Destination Address)
`TXFR_LEN:LongWord;`	DMA Channel CB Word 3 (Transfer Length)
`STRIDE:LongWord;`	DMA Channel CB Word 4 (2D Mode Stride) (Not applicable to Lite channels)
`NEXTCONBK:LongWord;`	DMA Channel CB Word 5 (Next Control Block Address)
`DEBUG:LongWord;`	DMA Channel Debug

BCM2838 DMA40 channel registers

PBCM2838DMA40Registers = ^TBCM2838DMA40Registers;

TBCM2838DMA40Registers = record

Note: Layout of the BCM2838 DMA40 Channel registers
`CS:LongWord; {DMA Channel Control and Status`
`CB:LongWord; {DMA Channel Control Block Address`
`Reserved1:LongWord;`
`DEBUG:LongWord;`	DMA Channel Debug
`TI:LongWord;`	DMA Channel CB Word 0 (Transfer Information)
`SRC:LongWord;`	DMA Channel CB Word 1 (Source Address)
`SRCI:LongWord;`	DMA Channel CB Word 2 (Source Information)
`DEST:LongWord;`	DMA Channel CB Word 3 (Destination Address)
`DESTI:LongWord;`	DMA Channel CB Word 4 (Destination Information)
`LEN:LongWord;`	DMA Channel CB Word 5 (Transfer Length)
`NEXT_CB:LongWord;`	DMA Channel CB Word 6 (Next Control Block Address)
`DEBUG2:LongWord;`	DMA Channel Debug

BCM2838 DMA control block structure

PBCM2838DMAControlBlock = ^TBCM2838DMAControlBlock;

TBCM2838DMAControlBlock = record

Note: Layout of BCM2838 DMA Control Block structure. Must be 32byte (256bit) aligned.
`TransferInformation:LongWord;`
`SourceAddress:LongWord;`
`DestinationAddress:LongWord;`
`TransferLength:LongWord;`
`ModeStride:LongWord;`	Not applicable to Lite channels
`NextControlBlockAddress:LongWord;`
`Reserved1:LongWord;`
`Reserved2:LongWord;`

BCM2838 DMA40 control block structure

PBCM2838DMA40ControlBlock = ^TBCM2838DMA40ControlBlock;

TBCM2838DMA40ControlBlock = record

Note: Layout of BCM2838 DMA40 Control Block structure. Must be 32byte (256bit) aligned.
`TransferInformation:LongWord;`
`SourceAddress:LongWord;`
`SourceInformation:LongWord;`
`DestinationAddress:LongWord;`
`DestinationInformation:LongWord;`
`TransferLength:LongWord;`
`NextControlBlockAddress:LongWord;`
`Reserved1:LongWord;`

BCM2838 BSC (I2C) registers

PBCM2838BSCRegisters = ^TBCM2838BSCRegisters;

TBCM2838BSCRegisters = record

Note: Layout of the BCM2838 BSC (I2C) registers
`C:LongWord;`	Control
`S:LongWord;`	Status
`DLEN:LongWord;`	Data Length
`A:LongWord;`	Slave Address
`FIFO:LongWord;`	Data FIFO
`CDIV:LongWord;`	Clock Divider
`DEL:LongWord;`	Data Delay

BCM2838 SPI0 registers

PBCM2838SPI0Registers = ^TBCM2838SPI0Registers;

TBCM2838SPI0Registers = record

Note: Layout of the BCM2838 SPI0 registers
`CS:LongWord;`	SPI Master Control and Status
`FIFO:LongWord;`	SPI Master TX and RX FIFOs
`CLK:LongWord;`	SPI Master Clock Divider
`DLEN:LongWord;`	SPI Master Data Length
`LTOH:LongWord;`	SPI LOSSI mode TOH
`DC:LongWord;`	SPI DMA DREQ Controls

BCM2838 I2C/SPI slave registers

PBCM2838I2CSPIRegisters = ^TBCM2838I2CSPIRegisters;

TBCM2838I2CSPIRegisters = record

Note: Layout of the BCM2838 I2C/SPI Slave registers
`DR:LongWord;`	Data Register
`RSR:LongWord;`	Operation status register and error clear register
`SLV:LongWord;`	I2C SPI Address Register holds the I2C slave address value
`CR:LongWord;`	Control register is used to configure the I2C or SPI operation
`FR:LongWord;`	Flag register
`IFLS:LongWord;`	Interrupt fifo level select register
`IMSC:LongWord;`	Interrupt Mask Set Clear Register
`RIS:LongWord;`	Raw Interrupt Status Register
`MIS:LongWord;`	Masked Interrupt Status Register
`ICR:LongWord;`	Interrupt Clear Register
`DMACR:LongWord;`	DMA Control Register
`TDR:LongWord;`	FIFO Test Data Register
`GPUSTAT:LongWord;`	GPU Status Register
`HCTRL:LongWord;`	Host Control Register
`DEBUG1:LongWord;`	I2C Debug Register
`DEBUG2:LongWord;`	SPI Debug Register

BCM2838 AUX (UART1, SPI1 and SPI2) registers

PBCM2838AUXRegisters = ^TBCM2838AUXRegisters;

TBCM2838AUXRegisters = record

Note: Layout of the BCM2838 AUX (UART1, SPI1 and SPI2) registers
`AUX_IRQ:LongWord;`	Auxiliary Interrupt status
`AUX_ENABLE:LongWord;`	Auxiliary enables
`Reserved01:LongWord;`
`Reserved02:LongWord;`
`Reserved03:LongWord;`
`Reserved04:LongWord;`
`Reserved05:LongWord;`
`Reserved06:LongWord;`
`Reserved07:LongWord;`
`Reserved08:LongWord;`
`Reserved09:LongWord;`
`Reserved0A:LongWord;`
`Reserved0B:LongWord;`
`Reserved0C:LongWord;`
`Reserved0D:LongWord;`
`Reserved0E:LongWord;`
`AUX_MU_IO:LongWord;`	Mini Uart I/O Data
`AUX_MU_IER:LongWord;`	Mini Uart Interrupt Enable
`AUX_MU_IIR:LongWord;`	Mini Uart Interrupt Identify
`AUX_MU_LCR:LongWord;`	Mini Uart Line Control
`AUX_MU_MCR:LongWord;`	Mini Uart Modem Control
`AUX_MU_LSR:LongWord;`	Mini Uart Line Status
`AUX_MU_MSR:LongWord;`	Mini Uart Modem Status
`AUX_MU_SCRATCH:LongWord;`	Mini Uart Scratch
`AUX_MU_CNTL:LongWord;`	Mini Uart Extra Control
`AUX_MU_STAT:LongWord;`	Mini Uart Extra Status
`AUX_MU_BAUD:LongWord;`	Mini Uart Baudrate
`Reserved11:LongWord;`
`Reserved12:LongWord;`
`Reserved13:LongWord;`
`Reserved14:LongWord;`
`Reserved15:LongWord;`
`AUX_SPI1_CNTL0:LongWord;`	SPI 1 Control register 0
`AUX_SPI1_CNTL1:LongWord;`	SPI 1 Control register 1
`AUX_SPI1_STAT:LongWord;`	SPI 1 Status
`Reserved21:LongWord;`
`AUX_SPI1_IO:LongWord;`	SPI 1 Data
`AUX_SPI1_PEEK:LongWord;`	SPI 1 Peek
`Reserved31:LongWord;`
`Reserved32:LongWord;`
`Reserved33:LongWord;`
`Reserved34:LongWord;`
`Reserved35:LongWord;`
`Reserved36:LongWord;`
`Reserved37:LongWord;`
`Reserved38:LongWord;`
`Reserved39:LongWord;`
`Reserved3A:LongWord;`
`AUX_SPI2_CNTL0:LongWord;`	SPI 2 Control register 0
`AUX_SPI2_CNTL1:LongWord;`	SPI 2 Control register 1
`AUX_SPI2_STAT:LongWord;`	SPI 2 Status
`Reserved40:LongWord;`
`AUX_SPI2_IO:LongWord;`	SPI 2 Data
`AUX_SPI2_PEEK:LongWord;`	SPI 2 Peek

BCM2838 PCM/I2S registers

PBCM2838PCMRegisters = ^TBCM2838PCMRegisters;

TBCM2838PCMRegisters = record

Note: Layout of the BCM2838 PCM/I2S registers
`CS_A:LongWord;`	PCM Control and Status
`FIFO_A:LongWord;`	PCM FIFO Data
`MODE_A:LongWord;`	PCM Mode
`RXC_A:LongWord;`	PCM Receive Configuration
`TXC_A:LongWord;`	PCM Transmit Configuration
`DREQ_A:LongWord;`
`INTEN_A:LongWord;`	PCM Interrupt Enables
`INTSTC_A:LongWord;`	PCM Interrupt Status & Clear
`GRAY:LongWord;`	PCM Gray Mode Control

BCM2838 pulse width modulator (PWM) registers

PBCM2838PWMRegisters = ^TBCM2838PWMRegisters;

TBCM2838PWMRegisters = record

Note: Layout of the BCM2838 Pulse Width Modulator (PWM) registers
`CTL:LongWord;`	PWM Control
`STA:LongWord;`	PWM Status
`DMAC:LongWord;`	PWM DMA Configuration
`Reserved1:LongWord;`
`RNG1:LongWord;`	PWM Channel 1 Range
`DAT1:LongWord;`	PWM Channel 1 Data
`FIF1:LongWord;`	PWM FIFO Input
`Reserved2:LongWord;`
`RNG2:LongWord;`	PWM Channel 2 Range
`DAT2:LongWord;`	PWM Channel 2 Data

BCM2838 PL011 UART registers

PBCM2838PL011Registers = ^TBCM2838PL011Registers;

TBCM2838PL011Registers = record

Note: Layout of the BCM2838 PL011 UART registers
`DR:LongWord;`	Data Register
`RSRECR:LongWord;`	Receive Status Register / Error Clear Register
`Reserved01:LongWord;`
`Reserved02:LongWord;`
`Reserved03:LongWord;`
`Reserved04:LongWord;`
`FR:LongWord;`	Flag register
`Reserved05:LongWord;`
`ILPR:LongWord;`	Not in use
`IBRD:LongWord;`	Integer Baud rate divisor
`FBRD:LongWord;`	Fractional Baud rate divisor
`LCRH:LongWord;`	Line Control register
`CR:LongWord;`	Control register
`IFLS:LongWord;`	Interrupt FIFO Level Select Register
`IMSC:LongWord;`	Interrupt Mask Set Clear Register
`RIS:LongWord;`	Raw Interrupt Status Register
`MIS:LongWord;`	Masked Interrupt Status Register
`ICR:LongWord;`	Interrupt Clear Register
`DMACR:LongWord;`	DMA Control Register
`Reserved11:LongWord;`
`Reserved12:LongWord;`
`Reserved13:LongWord;`
`Reserved14:LongWord;`
`Reserved15:LongWord;`
`Reserved16:LongWord;`
`Reserved17:LongWord;`
`Reserved18:LongWord;`
`Reserved19:LongWord;`
`Reserved1A:LongWord;`
`Reserved1B:LongWord;`
`Reserved1C:LongWord;`
`Reserved1D:LongWord;`
`ITCR:LongWord;`	Test Control Register
`ITIP:LongWord;`	Integration Test Input Register
`ITOP:LongWord;`	Integration Test Output Register
`TDR:LongWord;`	Test Data Register

BCM2838 ARM timer registers

PBCM2838ARMTimerRegisters = ^TBCM2838ARMTimerRegisters;

TBCM2838ARMTimerRegisters = record

Note: Layout of the BCM2838 ARM Timer registers
`Load:LongWord;`	Timer Load register
`Value:LongWord;`	Timer Value register
`Control:LongWord;`	Timer control register
`IRQClear:LongWord;`	Timer IRQ clear register
`RawIRQ:LongWord;`	Timer Raw IRQ register
`MaskedIRQ:LongWord;`	Timer Masked IRQ register
`Reload:LongWord;`	Timer Reload register
`Predivider:LongWord;`	The timer pre-divider register
`Counter:LongWord;`	Free running counter

BCM2838 power management watchdog registers

PBCM2838PMWatchdogRegisters = ^TBCM2838PMWatchdogRegisters;

TBCM2838PMWatchdogRegisters = record

Note: Layout of the BCM2838 Power Management Watchdog registers
`Reserved1:LongWord;`
`Reserved2:LongWord;`
`Reserved3:LongWord;`
`Reserved4:LongWord;`
`Reserved5:LongWord;`
`Reserved6:LongWord;`
`Reserved7:LongWord;`
`RSTC:LongWord;`
`RSTS:LongWord;`
`WDOG:LongWord;`

BCM2838 random number generator registers

PBCM2838RNGRegisters = ^TBCM2838RNGRegisters;

TBCM2838RNGRegisters = record

Note: Layout of the BCM2838 Random Number Generator registers
`Control:LongWord;`
`SoftResetRNG:LongWord;`
`SoftResetRBG:LongWord;`
`TotalBitCount:LongWord;`
`TBCThreshold:LongWord;`
`Reserved1:LongWord;`
`IntStatus:LongWord;`
`IntEnable:LongWord;`
`FIFOData:LongWord;`
`FIFOCount:LongWord;`

BCM2838 GPIO registers

PBCM2838GPIORegisters = ^TBCM2838GPIORegisters;

TBCM2838GPIORegisters = record

Note: Layout of the BCM2838 GPIO registers
`GPFSEL0:LongWord;`	GPIO Function Select 0
`GPFSEL1:LongWord;`	GPIO Function Select 1
`GPFSEL2:LongWord;`	GPIO Function Select 2
`GPFSEL3:LongWord;`	GPIO Function Select 3
`GPFSEL4:LongWord;`	GPIO Function Select 4
`GPFSEL5:LongWord;`	GPIO Function Select 5
`Reserved1:LongWord;`
`GPSET0:LongWord;`	GPIO Pin Output Set 0
`GPSET1:LongWord;`	GPIO Pin Output Set 1
`Reserved2:LongWord;`
`GPCLR0:LongWord;`	GPIO Pin Output Clear 0
`GPCLR1:LongWord;`	GPIO Pin Output Clear 1
`Reserved3:LongWord;`
`GPLEV0:LongWord;`	GPIO Pin Level 0
`GPLEV1:LongWord;`	GPIO Pin Level 1
`Reserved4:LongWord;`
`GPEDS0:LongWord;`	GPIO Pin Event Detect Status 0
`GPEDS1:LongWord;`	GPIO Pin Event Detect Status 1
`Reserved5:LongWord;`
`GPREN0:LongWord;`	GPIO Pin Rising Edge Detect Enable 0
`GPREN1:LongWord;`	GPIO Pin Rising Edge Detect Enable 1
`Reserved6:LongWord;`
`GPFEN0:LongWord;`	GPIO Pin Falling Edge Detect Enable 0
`GPFEN1:LongWord;`	GPIO Pin Falling Edge Detect Enable 1
`Reserved7:LongWord;`
`GPHEN0:LongWord;`	GPIO Pin High Detect Enable 0
`GPHEN1:LongWord;`	GPIO Pin High Detect Enable 1
`Reserved8:LongWord;`
`GPLEN0:LongWord;`	GPIO Pin Low Detect Enable 0
`GPLEN1:LongWord;`	GPIO Pin Low Detect Enable 1
`Reserved9:LongWord;`
`GPAREN0:LongWord;`	GPIO Pin Async. Rising Edge Detect 0
`GPAREN1:LongWord;`	GPIO Pin Async. Rising Edge Detect 1
`Reserved10:LongWord;`
`GPAFEN0:LongWord;`	GPIO Pin Async. Falling Edge Detect 0
`GPAFEN1:LongWord;`	GPIO Pin Async. Falling Edge Detect 1
`Reserved11:LongWord;`
`Reserved12:LongWord;`
`Reserved13:LongWord;`
`Reserved14:LongWord;`
`Reserved15:LongWord;`
`Reserved16:LongWord;`
`Reserved17:LongWord;`
`Reserved18:LongWord;`
`Reserved19:LongWord;`
`Reserved20:LongWord;`
`Reserved21:LongWord;`
`Reserved22:LongWord;`
`Reserved23:LongWord;`
`Reserved24:LongWord;`
`Reserved25:LongWord;`
`Reserved26:LongWord;`
`Reserved27:LongWord;`
`Reserved28:LongWord;`
`Reserved29:LongWord;`
`Reserved30:LongWord;`
`Reserved31:LongWord;`
`GPPUD0:LongWord;`	GPIO Pin Pull-up/down Mode 0
`GPPUD1:LongWord;`	GPIO Pin Pull-up/down Mode 1
`GPPUD2:LongWord;`	GPIO Pin Pull-up/down Mode 2
`GPPUD3:LongWord;`	GPIO Pin Pull-up/down Mode 3

BCM2838 mailbox0 registers

PBCM2838Mailbox0Registers = ^TBCM2838Mailbox0Registers;

TBCM2838Mailbox0Registers = record

Note: Layout of the BCM2838 Mailbox0 registers (See https://github.com/raspberrypi/firmware/wiki/Mailboxes)
`Read:LongWord;`	Offset 0x00 (The read register for mailbox 0)
`Reserved1:LongWord;`	Offset 0x04
`Reserved2:LongWord;`	Offset 0x08
`Reserved3:LongWord;`	Offset 0x0C
`Peek:LongWord;`	Offset 0x10 (Read from the mailbox without removing data from it)
`Sender:LongWord;`	Offset 0x14 (Sender ID (bottom 2 bits only))
`Status:LongWord;`	Offset 0x18 (The status register for mailbox 0)
`Config:LongWord;`	Offset 0x1C (The configuration register for mailbox 0)

BCM2838 mailbox1 registers

PBCM2838Mailbox1Registers = ^TBCM2838Mailbox1Registers;

TBCM2838Mailbox1Registers = record

Note: Layout of the BCM2838 Mailbox1 registers (See https://github.com/raspberrypi/firmware/wiki/Mailboxes)
`Write:LongWord;`	Offset 0x00 (The write register for mailbox 0) (Also the read register for mailbox 1)
`Reserved1:LongWord;`	Offset 0x04
`Reserved2:LongWord;`	Offset 0x08
`Reserved3:LongWord;`	Offset 0x0C
`Reserved4:LongWord;`	Offset 0x10
`Reserved5:LongWord;`	Offset 0x14
`Status:LongWord;`	Offset 0x18 (The status register for mailbox 1)
`Config:LongWord;`	Offset 0x1C (The configuration register for mailbox 1)

BCM2838 mailbox framebuffer request

PBCM2838MailboxFramebuffer = ^TBCM2838MailboxFramebuffer;

TBCM2838MailboxFramebuffer = record

Note: Layout of the BCM2838 Mailbox Framebuffer request (This structure must be 16 byte aligned when passed to the GPU)
`PhysicalWidth:LongWord;`	Requested width of Physical Framebuffer
`PhysicalHeight:LongWord;`	Requested height of Physical Framebuffer
`VirtualWidth:LongWord;`	Requested width of Virtual Display
`VirtualHeight:LongWord;`	Requested height of Virtual Display
`Pitch:LongWord;`	Zero on request, Number of Bytes per Row in response
`Depth:LongWord;`	Requested Colour Depth in Bits per Pixel
`OffsetX:LongWord;`	Requested X offset of Virtual Framebuffer
`OffsetY:LongWord;`	Requested Y offset of Virtual Framebuffer
`Address:LongWord;`	Framebuffer address (Zero on request, Failure if zero in response)
`Size:LongWord;`	Framebuffer size (Zero on request, Size in bytes in response)

BCM2838 mailbox header property tags

PBCM2838MailboxHeader = ^TBCM2838MailboxHeader;

TBCM2838MailboxHeader = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Header
`Size:LongWord;`	Total buffer size in bytes (including the header values, the end tag and padding)
`Code:LongWord;`	Request/response code

BCM2838 mailbox footer property tags

PBCM2838MailboxFooter = ^TBCM2838MailboxFooter;

TBCM2838MailboxFooter = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Footer
`Tag:LongWord;`	BCM2838_MBOX_TAG_END

BCM2838 mailbox tag header

PBCM2838MailboxTagHeader = ^TBCM2838MailboxTagHeader;

TBCM2838MailboxTagHeader = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Tag Header
`Tag:LongWord;`	Tag identifier
`Size:LongWord;`	Value buffer size in bytes
`Length:LongWord;`	1 bit (MSB) request/response indicator (0=request, 1=response), 31 bits (LSB) value length in bytes

BCM2838 mailbox tag no request

PBCM2838MailboxTagNoRequest = ^TBCM2838MailboxTagNoRequest;

TBCM2838MailboxTagNoRequest = record

Tag No Request

BCM2838 mailbox tag no response

PBCM2838MailboxTagNoResponse = ^TBCM2838MailboxTagNoResponse;

TBCM2838MailboxTagNoResponse = record

Tag No Response

BCM2838 mailbox tag firmware revision response

TBCM2838MailboxTagFirmwareRevisionResponse = record

Get Firmware Revision
`Revision:LongWord;`

BCM2838 mailbox tag get firmware revision

PBCM2838MailboxTagGetFirmwareRevision = ^TBCM2838MailboxTagGetFirmwareRevision;

TBCM2838MailboxTagGetFirmwareRevision = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagFirmwareRevisionResponse);`

BCM2838 mailbox tag board model response

TBCM2838MailboxTagBoardModelResponse = record

Get Board Model
`Model:LongWord;`

BCM2838 mailbox tag get board model

PBCM2838MailboxTagGetBoardModel = ^TBCM2838MailboxTagGetBoardModel;

TBCM2838MailboxTagGetBoardModel = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagBoardModelResponse);`

BCM2838 mailbox tag board revision response

TBCM2838MailboxTagBoardRevisionResponse = record

Get Board Revision
`Revision:LongWord;`

BCM2838 mailbox tag get board revision

PBCM2838MailboxTagGetBoardRevision = ^TBCM2838MailboxTagGetBoardRevision;

TBCM2838MailboxTagGetBoardRevision = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagBoardRevisionResponse);`

BCM2838 mailbox tag MAC address response

TBCM2838MailboxTagMACAddressResponse = record

Get MAC Address
`MAC:array[0..5] of Byte;`	MAC address in network byte order
`Padding:Word;`

BCM2838 mailbox tag get MAC address

PBCM2838MailboxTagGetMACAddress = ^TBCM2838MailboxTagGetMACAddress;

TBCM2838MailboxTagGetMACAddress = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagMACAddressResponse);`

BCM2838 mailbox tag board serial response

TBCM2838MailboxTagBoardSerialResponse = record

Get Board Serial
`Serial:Int64;`

BCM2838 mailbox tag get board serial

PBCM2838MailboxTagGetBoardSerial = ^TBCM2838MailboxTagGetBoardSerial;

TBCM2838MailboxTagGetBoardSerial = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagBoardSerialResponse);`

BCM2838 mailbox tag ARM memory response

TBCM2838MailboxTagARMMemoryResponse = record

Get ARM Memory
`Address:LongWord;`	Base address in bytes
`Size:LongWord;`	Size in bytes

BCM2838 mailbox tag get ARM memory

PBCM2838MailboxTagGetARMMemory = ^TBCM2838MailboxTagGetARMMemory;

TBCM2838MailboxTagGetARMMemory = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagARMMemoryResponse);`

BCM2838 mailbox tag VC memory response

TBCM2838MailboxTagVCMemoryResponse = record

Get VC Memory
`Address:LongWord;`	Base address in bytes
`Size:LongWord;`	Size in bytes

BCM2838 mailbox tag get VC memory

PBCM2838MailboxTagGetVCMemory = ^TBCM2838MailboxTagGetVCMemory;

TBCM2838MailboxTagGetVCMemory = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagVCMemoryResponse);`

BCM2838 mailbox tag clock response

TBCM2838MailboxTagClockResponse = record

Get Clocks
`ParentId:LongWord;`
`ClockId:LongWord;`

BCM2838 mailbox tag clocks response

TBCM2838MailboxTagClocksResponse = record

`Clocks:array[0..255] of TBCM2838MailboxTagClockResponse;`

BCM2838 mailbox tag get clocks

PBCM2838MailboxTagGetClocks = ^TBCM2838MailboxTagGetClocks;

TBCM2838MailboxTagGetClocks = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagClocksResponse);`

BCM2838 mailbox tag get power state request

TBCM2838MailboxTagGetPowerStateRequest = record

Get Power State
`DeviceId:LongWord;`

BCM2838 mailbox tag power state response

TBCM2838MailboxTagPowerStateResponse = record

`DeviceId:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag get power state

PBCM2838MailboxTagGetPowerState = ^TBCM2838MailboxTagGetPowerState;

TBCM2838MailboxTagGetPowerState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetPowerStateRequest);`
`1:(Response:TBCM2838MailboxTagPowerStateResponse);`

BCM2838 mailbox tag timing request

TBCM2838MailboxTagTimingRequest = record

Get Timing
`DeviceId:LongWord;`

BCM2838 mailbox tag timing response

TBCM2838MailboxTagTimingResponse = record

`DeviceId:LongWord;`
`Wait:LongWord;`	Enable wait time in microseconds

BCM2838 mailbox tag get timing

PBCM2838MailboxTagGetTiming = ^TBCM2838MailboxTagGetTiming;

TBCM2838MailboxTagGetTiming = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagTimingRequest);`
`1:(Response:TBCM2838MailboxTagTimingResponse);`

BCM2838 mailbox tag set power state request

TBCM2838MailboxTagSetPowerStateRequest = record

Set Power State
`DeviceId:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag set power state

PBCM2838MailboxTagSetPowerState = ^TBCM2838MailboxTagSetPowerState;

TBCM2838MailboxTagSetPowerState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetPowerStateRequest);`
`1:(Response:TBCM2838MailboxTagPowerStateResponse);`

BCM2838 mailbox tag get clock state request

TBCM2838MailboxTagGetClockStateRequest = record

Get Clock State
`ClockId:LongWord;`

BCM2838 mailbox tag clock state response

TBCM2838MailboxTagClockStateResponse = record

`ClockId:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag get clock state

PBCM2838MailboxTagGetClockState = ^TBCM2838MailboxTagGetClockState;

TBCM2838MailboxTagGetClockState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetClockStateRequest);`
`1:(Response:TBCM2838MailboxTagClockStateResponse);`

BCM2838 mailbox tag set clock state request

TBCM2838MailboxTagSetClockStateRequest = record

Set Clock State
`ClockId:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag set clock state

PBCM2838MailboxTagSetClockState = ^TBCM2838MailboxTagSetClockState;

TBCM2838MailboxTagSetClockState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetClockStateRequest);`
`1:(Response:TBCM2838MailboxTagClockStateResponse);`

BCM2838 mailbox tag get clock rate request

TBCM2838MailboxTagGetClockRateRequest = record

Get Clock Rate
`ClockId:LongWord;`

BCM2838 mailbox tag clock rate response

TBCM2838MailboxTagClockRateResponse = record

`ClockId:LongWord;`
`Rate:LongWord;`	In Hz

BCM2838 mailbox tag get clock rate

PBCM2838MailboxTagGetClockRate = ^TBCM2838MailboxTagGetClockRate;

TBCM2838MailboxTagGetClockRate = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetClockRateRequest);`
`1:(Response:TBCM2838MailboxTagClockRateResponse);`

BCM2838 mailbox tag set clock rate request

TBCM2838MailboxTagSetClockRateRequest = record

Set Clock Rate
`ClockId:LongWord;`
`Rate:LongWord;`	In Hz
`SkipTurbo:LongWord;`

BCM2838 mailbox tag set clock rate

PBCM2838MailboxTagSetClockRate = ^TBCM2838MailboxTagSetClockRate;

TBCM2838MailboxTagSetClockRate = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetClockRateRequest);`
`1:(Response:TBCM2838MailboxTagClockRateResponse);`

BCM2838 mailbox tag get clock max rate request

TBCM2838MailboxTagGetClockMaxRateRequest = record

Get Clock Max Rate
`ClockId:LongWord;`

BCM2838 mailbox tag get clock max rate response

TBCM2838MailboxTagGetClockMaxRateResponse = record

`ClockId:LongWord;`
`Rate:LongWord;`	In Hz

BCM2838 mailbox tag get clock max rate

PBCM2838MailboxTagGetClockMaxRate = ^TBCM2838MailboxTagGetClockMaxRate;

TBCM2838MailboxTagGetClockMaxRate = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetClockMaxRateRequest);`
`1:(Response:TBCM2838MailboxTagGetClockMaxRateResponse);`

BCM2838 mailbox tag get clock min rate

PBCM2838MailboxTagGetClockMinRate = ^TBCM2838MailboxTagGetClockMinRate;

TBCM2838MailboxTagGetClockMinRate = record

Get Clock Min Rate
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetClockMaxRateRequest);`
`1:(Response:TBCM2838MailboxTagGetClockMaxRateResponse);`

BCM2838 mailbox tag get turbo request

TBCM2838MailboxTagGetTurboRequest = record

Get Turbo
`Id:LongWord;`

BCM2838 mailbox tag turbo response

TBCM2838MailboxTagTurboResponse = record

`Id:LongWord;`
`Level:LongWord;`

BCM2838 mailbox tag get turbo

PBCM2838MailboxTagGetTurbo = ^TBCM2838MailboxTagGetTurbo;

TBCM2838MailboxTagGetTurbo = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetTurboRequest);`
`1:(Response:TBCM2838MailboxTagTurboResponse);`

BCM2838 mailbox tag set turbo request

TBCM2838MailboxTagSetTurboRequest = record

Set Turbo
`Id:LongWord;`
`Level:LongWord;`

BCM2838 mailbox tag set turbo

PBCM2838MailboxTagSetTurbo = ^TBCM2838MailboxTagSetTurbo;

TBCM2838MailboxTagSetTurbo = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetTurboRequest);`
`1:(Response:TBCM2838MailboxTagTurboResponse);`

BCM2838 mailbox tag get voltage request

TBCM2838MailboxTagGetVoltageRequest = record

Get Voltage
`VoltageId:LongWord;`

BCM2838 mailbox tag voltage response

TBCM2838MailboxTagVoltageResponse = record

`VoltageId:LongWord;`
`Value:LongWord;`	Offset from 1.2V in units of 0.025V

BCM2838 mailbox tag get voltage

PBCM2838MailboxTagGetVoltage = ^TBCM2838MailboxTagGetVoltage;

TBCM2838MailboxTagGetVoltage = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetVoltageRequest);`
`1:(Response:TBCM2838MailboxTagVoltageResponse);`

BCM2838 mailbox tag set voltage request

TBCM2838MailboxTagSetVoltageRequest = record

Set Voltage
`VoltageId:LongWord;`
`Value:LongWord;`	Offset from 1.2V in units of 0.025V

BCM2838 mailbox tag set voltage

PBCM2838MailboxTagSetVoltage = ^TBCM2838MailboxTagSetVoltage;

TBCM2838MailboxTagSetVoltage = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetVoltageRequest);`
`1:(Response:TBCM2838MailboxTagVoltageResponse);`

BCM2838 mailbox tag get max voltage

PBCM2838MailboxTagGetMaxVoltage = ^TBCM2838MailboxTagGetMaxVoltage;

TBCM2838MailboxTagGetMaxVoltage = record

Get Max Voltage
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetVoltageRequest);`
`1:(Response:TBCM2838MailboxTagVoltageResponse);`

BCM2838 mailbox tag get min voltage

PBCM2838MailboxTagGetMinVoltage = ^TBCM2838MailboxTagGetMinVoltage;

TBCM2838MailboxTagGetMinVoltage = record

Get Min Voltage
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetVoltageRequest);`
`1:(Response:TBCM2838MailboxTagVoltageResponse);`

BCM2838 mailbox tag temperature request

TBCM2838MailboxTagTemperatureRequest = record

Get Temperature
`TemperatureId:LongWord;`

BCM2838 mailbox tag temperature response

TBCM2838MailboxTagTemperatureResponse = record

`TemperatureId:LongWord;`	Should be zero
`Temperature:LongWord;`	Return the temperature of the SoC in thousandths of a degree C

BCM2838 mailbox tag get temperature

PBCM2838MailboxTagGetTemperature = ^TBCM2838MailboxTagGetTemperature;

TBCM2838MailboxTagGetTemperature = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagTemperatureRequest);`
`1:(Response:TBCM2838MailboxTagTemperatureResponse);`

BCM2838 mailbox tag get max temperature

PBCM2838MailboxTagGetMaxTemperature = ^TBCM2838MailboxTagGetMaxTemperature;

TBCM2838MailboxTagGetMaxTemperature = record

Get Max Temp
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagTemperatureRequest);`
`1:(Response:TBCM2838MailboxTagTemperatureResponse);`

BCM2838 mailbox tag allocate memory request

TBCM2838MailboxTagAllocateMemoryRequest = record

Allocate Memory
`Size:LongWord;`
`Alignment:LongWord;`
`Flags:LongWord;`

BCM2838 mailbox tag allocate memory response

TBCM2838MailboxTagAllocateMemoryResponse = record

`Handle:THandle;`

BCM2838 mailbox tag allocate memory

PBCM2838MailboxTagAllocateMemory = ^TBCM2838MailboxTagAllocateMemory;

TBCM2838MailboxTagAllocateMemory = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagAllocateMemoryRequest);`
`1:(Response:TBCM2838MailboxTagAllocateMemoryResponse);`

BCM2838 mailbox tag lock memory request

TBCM2838MailboxTagLockMemoryRequest = record

Lock Memory
`Handle:THandle;`

BCM2838 mailbox tag lock memory response

TBCM2838MailboxTagLockMemoryResponse = record

`Address:LongWord;`	Bus Address

BCM2838 mailbox tag lock memory

PBCM2838MailboxTagLockMemory = ^TBCM2838MailboxTagLockMemory;

TBCM2838MailboxTagLockMemory = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagLockMemoryRequest);`
`1:(Response:TBCM2838MailboxTagLockMemoryResponse);`

BCM2838 mailbox tag unlock memory response

TBCM2838MailboxTagUnlockMemoryResponse = record

Unlock Memory
`Status:LongWord;`	0 is Success

BCM2838 mailbox tag unlock memory

PBCM2838MailboxTagUnlockMemory = ^TBCM2838MailboxTagUnlockMemory;

TBCM2838MailboxTagUnlockMemory = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagLockMemoryRequest);`
`1:(Response:TBCM2838MailboxTagUnlockMemoryResponse);`

BCM2838 mailbox tag release memory

PBCM2838MailboxTagReleaseMemory = ^TBCM2838MailboxTagReleaseMemory;

TBCM2838MailboxTagReleaseMemory = record

Release Memory
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagLockMemoryRequest);`
`1:(Response:TBCM2838MailboxTagUnlockMemoryResponse);`

BCM2838 mailbox tag execute code request

TBCM2838MailboxTagExecuteCodeRequest = record

Execute Code
`Address:Pointer;`	Bus Address
`R0:LongWord;`
`R1:LongWord;`
`R2:LongWord;`
`R3:LongWord;`
`R4:LongWord;`
`R5:LongWord;`

BCM2838 mailbox tag execute code response

TBCM2838MailboxTagExecuteCodeResponse = record

`R0:LongWord;`

BCM2838 mailbox tag execute code

PBCM2838MailboxTagExecuteCode = ^TBCM2838MailboxTagExecuteCode;

TBCM2838MailboxTagExecuteCode = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagExecuteCodeRequest);`
`1:(Response:TBCM2838MailboxTagExecuteCodeResponse);`

BCM2838 mailbox tag execute QPU request

TBCM2838MailboxTagExecuteQPURequest = record

Execute QPU
`NumQPUs:LongWord;`
`Control:LongWord;`
`NoFlush:LongWord;`
`Timeout:LongWord;`	Milliseconds

BCM2838 mailbox tag execute QPU response

TBCM2838MailboxTagExecuteQPUResponse = record

`Status:LongWord;`	0 is Success / 0x80000000 is Timeout

BCM2838 mailbox tag execute QPU

PBCM2838MailboxTagExecuteQPU = ^TBCM2838MailboxTagExecuteQPU;

TBCM2838MailboxTagExecuteQPU = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagExecuteQPURequest);`
`1:(Response:TBCM2838MailboxTagExecuteQPUResponse);`

BCM2838 mailbox tag enable QPU request

TBCM2838MailboxTagEnableQPURequest = record

Enable QPU
`Enable:LongWord;`

BCM2838 mailbox tag enable QPU response

TBCM2838MailboxTagEnableQPUResponse = record

`Status:LongWord;`	0 is Success

BCM2838 mailbox tag enable QPU

PBCM2838MailboxTagEnableQPU = ^TBCM2838MailboxTagEnableQPU;

TBCM2838MailboxTagEnableQPU = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagEnableQPURequest);`
`1:(Response:TBCM2838MailboxTagEnableQPUResponse);`

BCM2838 mailbox tag get dispmanx handle request

TBCM2838MailboxTagGetDispmanxHandleRequest = record

Get Dispmanx Handle
`Resource:THandle;`

BCM2838 mailbox tag get dispmanx handle response

TBCM2838MailboxTagGetDispmanxHandleResponse = record

`Status:LongWord;`	0 is Success
`Memory:THandle;`

BCM2838 mailbox tag get dispmanx handle

PBCM2838MailboxTagGetDispmanxHandle = ^TBCM2838MailboxTagGetDispmanxHandle;

TBCM2838MailboxTagGetDispmanxHandle = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetDispmanxHandleRequest);`
`1:(Response:TBCM2838MailboxTagGetDispmanxHandleResponse);`

BCM2838 mailbox tag get EDID block request

TBCM2838MailboxTagGetEDIDBlockRequest = record

Get EDID Block
`Block:LongWord;`	Starting from 0

BCM2838 mailbox tag get EDID block response

TBCM2838MailboxTagGetEDIDBlockResponse = record

`Block:LongWord;`	Starting from 0
`Status:LongWord;`	0 is Success
`EDID:array[0..127] of Byte;`

BCM2838 mailbox tag get EDID block

PBCM2838MailboxTagGetEDIDBlock = ^TBCM2838MailboxTagGetEDIDBlock;

TBCM2838MailboxTagGetEDIDBlock = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetEDIDBlockRequest);`
`1:(Response:TBCM2838MailboxTagGetEDIDBlockResponse);`

BCM2838 mailbox tag GPIO state request

TBCM2838MailboxTagGPIOStateRequest = record

Get GPIO State
`GPIO:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag GPIO state response

TBCM2838MailboxTagGPIOStateResponse = record

`GPIO:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag get GPIO state

PBCM2838MailboxTagGetGPIOState = ^TBCM2838MailboxTagGetGPIOState;

TBCM2838MailboxTagGetGPIOState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGPIOStateRequest);`
`1:(Response:TBCM2838MailboxTagGPIOStateResponse);`

BCM2838 mailbox tag set GPIO state

PBCM2838MailboxTagSetGPIOState = ^TBCM2838MailboxTagSetGPIOState;

TBCM2838MailboxTagSetGPIOState = record

Set GPIO State
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGPIOStateRequest);`
`1:(Response:TBCM2838MailboxTagGPIOStateResponse);`

BCM2838 mailbox tag get GPIO config request

TBCM2838MailboxTagGetGPIOConfigRequest = record

Get GPIO Config
`GPIO:LongWord;`
`Direction:LongWord;`
`Polarity:LongWord;`
`Terminator:LongWord;`
`PullUp:LongWord;`

BCM2838 mailbox tag get GPIO config response

TBCM2838MailboxTagGetGPIOConfigResponse = record

`GPIO:LongWord;`
`Direction:LongWord;`
`Polarity:LongWord;`
`Terminator:LongWord;`
`PullUp:LongWord;`

BCM2838 mailbox tag get GPIO config

PBCM2838MailboxTagGetGPIOConfig = ^TBCM2838MailboxTagGetGPIOConfig;

TBCM2838MailboxTagGetGPIOConfig = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetGPIOConfigRequest);`
`1:(Response:TBCM2838MailboxTagGetGPIOConfigResponse);`

BCM2838 mailbox tag set GPIO config request

TBCM2838MailboxTagSetGPIOConfigRequest = record

Set GPIO Config
`GPIO:LongWord;`
`Direction:LongWord;`
`Polarity:LongWord;`
`Terminator:LongWord;`
`PullUp:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag set GPIO config response

TBCM2838MailboxTagSetGPIOConfigResponse = record

`GPIO:LongWord;`
`Direction:LongWord;`
`Polarity:LongWord;`
`Terminator:LongWord;`
`PullUp:LongWord;`
`State:LongWord;`

BCM2838 mailbox tag set GPIO config

PBCM2838MailboxTagSetGPIOConfig = ^TBCM2838MailboxTagSetGPIOConfig;

TBCM2838MailboxTagSetGPIOConfig = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetGPIOConfigRequest);`
`1:(Response:TBCM2838MailboxTagSetGPIOConfigResponse);`

BCM2838 mailbox tag get throttled request

TBCM2838MailboxTagGetThrottledRequest = record

Get Throttled
`Value:LongWord;`

BCM2838 mailbox tag get throttled response

TBCM2838MailboxTagGetThrottledResponse = record

`Value:LongWord;`

BCM2838 mailbox tag get throttled

PBCM2838MailboxTagGetThrottled = ^TBCM2838MailboxTagGetThrottled;

TBCM2838MailboxTagGetThrottled = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetThrottledRequest);`
`1:(Response:TBCM2838MailboxTagGetThrottledResponse);`

BCM2838 mailbox tag allocate buffer request

TBCM2838MailboxTagAllocateBufferRequest = record

Allocate Buffer
`Alignment:LongWord;`	Bytes

BCM2838 mailbox tag allocate buffer response

TBCM2838MailboxTagAllocateBufferResponse = record

`Address:LongWord;`	Base Address in Bytes
`Size:LongWord;`	Size in Bytes

BCM2838 mailbox tag allocate buffer

PBCM2838MailboxTagAllocateBuffer = ^TBCM2838MailboxTagAllocateBuffer;

TBCM2838MailboxTagAllocateBuffer = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagAllocateBufferRequest);`
`1:(Response:TBCM2838MailboxTagAllocateBufferResponse);`

BCM2838 mailbox tag release buffer

PBCM2838MailboxTagReleaseBuffer = ^TBCM2838MailboxTagReleaseBuffer;

TBCM2838MailboxTagReleaseBuffer = record

Release Buffer
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagNoResponse);`

BCM2838 mailbox tag blank screen request

TBCM2838MailboxTagBlankScreenRequest = record

Blank Screen
`State:LongWord;`

BCM2838 mailbox tag blank screen response

TBCM2838MailboxTagBlankScreenResponse = record

`State:LongWord;`

BCM2838 mailbox tag blank screen

PBCM2838MailboxTagBlankScreen = ^TBCM2838MailboxTagBlankScreen;

TBCM2838MailboxTagBlankScreen = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagBlankScreenRequest);`
`1:(Response:TBCM2838MailboxTagBlankScreenResponse);`

BCM2838 mailbox tag physical request

TBCM2838MailboxTagPhysicalRequest = record

Get Physical
`Width:LongWord;`	Pixels
`Height:Longword;`	Pixels

BCM2838 mailbox tag physical response

TBCM2838MailboxTagPhysicalResponse = record

`Width:LongWord;`	Pixels
`Height:Longword;`	Pixels

BCM2838 mailbox tag get physical

PBCM2838MailboxTagGetPhysical = ^TBCM2838MailboxTagGetPhysical;

TBCM2838MailboxTagGetPhysical = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagPhysicalResponse);`

BCM2838 mailbox tag test physical

PBCM2838MailboxTagTestPhysical = ^TBCM2838MailboxTagTestPhysical;

TBCM2838MailboxTagTestPhysical = record

Test Physical
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPhysicalRequest);`
`1:(Response:TBCM2838MailboxTagPhysicalResponse);`

BCM2838 mailbox tag set physical

PBCM2838MailboxTagSetPhysical = ^TBCM2838MailboxTagSetPhysical;

TBCM2838MailboxTagSetPhysical = record

Set Physical
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPhysicalRequest);`
`1:(Response:TBCM2838MailboxTagPhysicalResponse);`

BCM2838 mailbox tag virtual request

TBCM2838MailboxTagVirtualRequest = record

Get Virtual
`Width:LongWord;`	Pixels
`Height:Longword;`	Pixels

BCM2838 mailbox tag virtual response

TBCM2838MailboxTagVirtualResponse = record

`Width:LongWord;`	Pixels
`Height:Longword;`	Pixels

BCM2838 mailbox tag get virtual

PBCM2838MailboxTagGetVirtual = ^TBCM2838MailboxTagGetVirtual;

TBCM2838MailboxTagGetVirtual = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagVirtualResponse);`

BCM2838 mailbox tag test virtual

PBCM2838MailboxTagTestVirtual = ^TBCM2838MailboxTagTestVirtual;

TBCM2838MailboxTagTestVirtual = record

Test Virtual
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagVirtualRequest);`
`1:(Response:TBCM2838MailboxTagVirtualResponse);`

BCM2838 mailbox tag set virtual

PBCM2838MailboxTagSetVirtual = ^TBCM2838MailboxTagSetVirtual;

TBCM2838MailboxTagSetVirtual = record

Set Virtual
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagVirtualRequest);`
`1:(Response:TBCM2838MailboxTagVirtualResponse);`

BCM2838 mailbox tag depth request

TBCM2838MailboxTagDepthRequest = record

Get Depth
`Depth:LongWord;`	Bits per pixel

BCM2838 mailbox tag depth response

TBCM2838MailboxTagDepthResponse = record

`Depth:LongWord;`	Bits per pixel

BCM2838 mailbox tag get depth

PBCM2838MailboxTagGetDepth = ^TBCM2838MailboxTagGetDepth;

TBCM2838MailboxTagGetDepth = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagDepthResponse);`

BCM2838 mailbox tag test depth

PBCM2838MailboxTagTestDepth = ^TBCM2838MailboxTagTestDepth;

TBCM2838MailboxTagTestDepth = record

Test Depth
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagDepthRequest);`
`1:(Response:TBCM2838MailboxTagDepthResponse);`

BCM2838 mailbox tag set depth

PBCM2838MailboxTagSetDepth = ^TBCM2838MailboxTagSetDepth;

TBCM2838MailboxTagSetDepth = record

Set Depth
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagDepthRequest);`
`1:(Response:TBCM2838MailboxTagDepthResponse);`

BCM2838 mailbox tag pixel order request

TBCM2838MailboxTagPixelOrderRequest = record

Get Pixel Order
`Order:LongWord;`

BCM2838 mailbox tag pixel order response

TBCM2838MailboxTagPixelOrderResponse = record

`Order:LongWord;`

BCM2838 mailbox tag get pixel order

PBCM2838MailboxTagGetPixelOrder = ^TBCM2838MailboxTagGetPixelOrder;

TBCM2838MailboxTagGetPixelOrder = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagPixelOrderResponse);`

BCM2838 mailbox tag test pixel order

PBCM2838MailboxTagTestPixelOrder = ^TBCM2838MailboxTagTestPixelOrder;

TBCM2838MailboxTagTestPixelOrder = record

Test Pixel Order
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPixelOrderRequest);`
`1:(Response:TBCM2838MailboxTagPixelOrderResponse);`

BCM2838 mailbox tag set pixel order

PBCM2838MailboxTagSetPixelOrder = ^TBCM2838MailboxTagSetPixelOrder;

TBCM2838MailboxTagSetPixelOrder = record

Set Pixel Order
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPixelOrderRequest);`
`1:(Response:TBCM2838MailboxTagPixelOrderResponse);`

BCM2838 mailbox tag alpha mode request

TBCM2838MailboxTagAlphaModeRequest = record

Get Alpha Mode
`Mode:LongWord;`

BCM2838 mailbox tag alpha mode response

TBCM2838MailboxTagAlphaModeResponse = record

`Mode:LongWord;`

BCM2838 mailbox tag get alpha mode

PBCM2838MailboxTagGetAlphaMode = ^TBCM2838MailboxTagGetAlphaMode;

TBCM2838MailboxTagGetAlphaMode = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagAlphaModeResponse);`

BCM2838 mailbox tag test alpha mode

PBCM2838MailboxTagTestAlphaMode = ^TBCM2838MailboxTagTestAlphaMode;

TBCM2838MailboxTagTestAlphaMode = record

Test Alpha Mode
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagAlphaModeRequest);`
`1:(Response:TBCM2838MailboxTagAlphaModeResponse);`

BCM2838 mailbox tag set alpha mode

PBCM2838MailboxTagSetAlphaMode = ^TBCM2838MailboxTagSetAlphaMode;

TBCM2838MailboxTagSetAlphaMode = record

Set Alpha Mode
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagAlphaModeRequest);`
`1:(Response:TBCM2838MailboxTagAlphaModeResponse);`

BCM2838 mailbox tag pitch response

TBCM2838MailboxTagPitchResponse = record

Get Pitch
`Pitch:LongWord;`	Bytes per line

BCM2838 mailbox tag get pitch

PBCM2838MailboxTagGetPitch = ^TBCM2838MailboxTagGetPitch;

TBCM2838MailboxTagGetPitch = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagPitchResponse);`

BCM2838 mailbox tag virtual offset request

TBCM2838MailboxTagVirtualOffsetRequest = record

Get Virtual Offset
`X:LongWord;`	Pixels
`Y:LongWord;`	Pixels

BCM2838 mailbox tag virtual offset response

TBCM2838MailboxTagVirtualOffsetResponse = record

`X:LongWord;`	Pixels
`Y:LongWord;`	Pixels

BCM2838 mailbox tag get virtual offset

PBCM2838MailboxTagGetVirtualOffset = ^TBCM2838MailboxTagGetVirtualOffset;

TBCM2838MailboxTagGetVirtualOffset = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);`

BCM2838 mailbox tag test virtual offset

PBCM2838MailboxTagTestVirtualOffset = ^TBCM2838MailboxTagTestVirtualOffset;

TBCM2838MailboxTagTestVirtualOffset = record

Test Virtual Offset
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagVirtualOffsetRequest);`
`1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);`

BCM2838 mailbox tag set virtual offset

PBCM2838MailboxTagSetVirtualOffset = ^TBCM2838MailboxTagSetVirtualOffset;

TBCM2838MailboxTagSetVirtualOffset = record

Set Virtual Offset
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagVirtualOffsetRequest);`
`1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);`

BCM2838 mailbox tag overscan request

TBCM2838MailboxTagOverscanRequest = record

Get Overscan
`Top:LongWord;`	Pixels
`Bottom:LongWord;`	Pixels
`Left:LongWord;`	Pixels
`Right:LongWord;`	Pixels

BCM2838 mailbox tag overscan response

TBCM2838MailboxTagOverscanResponse = record

`Top:LongWord;`	Pixels
`Bottom:LongWord;`	Pixels
`Left:LongWord;`	Pixels
`Right:LongWord;`	Pixels

BCM2838 mailbox tag get overscan

PBCM2838MailboxTagGetOverscan = ^TBCM2838MailboxTagGetOverscan;

TBCM2838MailboxTagGetOverscan = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagOverscanResponse);`

BCM2838 mailbox tag test overscan

PBCM2838MailboxTagTestOverscan = ^TBCM2838MailboxTagTestOverscan;

TBCM2838MailboxTagTestOverscan = record

Test Overscan
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagOverscanRequest);`
`1:(Response:TBCM2838MailboxTagOverscanResponse);`

BCM2838 mailbox tag set overscan

PBCM2838MailboxTagSetOverscan = ^TBCM2838MailboxTagSetOverscan;

TBCM2838MailboxTagSetOverscan = record

Set Overscan
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagOverscanRequest);`
`1:(Response:TBCM2838MailboxTagOverscanResponse);`

BCM2838 mailbox tag get palette response

TBCM2838MailboxTagGetPaletteResponse = record

Get Palette
`Values:array[0..255] of LongWord;`	RGBA Palette Values

BCM2838 mailbox tag get palette

PBCM2838MailboxTagGetPalette = ^TBCM2838MailboxTagGetPalette;

TBCM2838MailboxTagGetPalette = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagGetPaletteResponse);`

BCM2838 mailbox tag palette request

TBCM2838MailboxTagPaletteRequest = record

Test Palette
`Offset:LongWord;`	First palette index to set (0-255)
`Length:LongWord;`	Number of palette entries to set (1-256)
`Values:array[0..255] of LongWord;`	RGBA Palette Values

BCM2838 mailbox tag palette response

TBCM2838MailboxTagPaletteResponse = record

`Status:LongWord;`

BCM2838 mailbox tag test palette

PBCM2838MailboxTagTestPalette = ^TBCM2838MailboxTagTestPalette;

TBCM2838MailboxTagTestPalette = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPaletteRequest);`
`1:(Response:TBCM2838MailboxTagPaletteResponse);`

BCM2838 mailbox tag set palette

PBCM2838MailboxTagSetPalette = ^TBCM2838MailboxTagSetPalette;

TBCM2838MailboxTagSetPalette = record

Set Palette
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagPaletteRequest);`
`1:(Response:TBCM2838MailboxTagPaletteResponse);`

BCM2838 mailbox tag layer request

TBCM2838MailboxTagLayerRequest = record

Get Layer
`Layer:LongInt;`

BCM2838 mailbox tag layer response

TBCM2838MailboxTagLayerResponse = record

`Layer:LongInt;`

BCM2838 mailbox tag get layer

PBCM2838MailboxTagGetLayer = ^TBCM2838MailboxTagGetLayer;

TBCM2838MailboxTagGetLayer = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagLayerResponse);`

BCM2838 mailbox tag test layer

PBCM2838MailboxTagTestLayer = ^TBCM2838MailboxTagTestLayer;

TBCM2838MailboxTagTestLayer = record

Test Layer
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagLayerRequest);`
`1:(Response:TBCM2838MailboxTagLayerResponse);`

BCM2838 mailbox tag set layer

PBCM2838MailboxTagSetLayer = ^TBCM2838MailboxTagSetLayer;

TBCM2838MailboxTagSetLayer = record

Set Layer
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagLayerRequest);`
`1:(Response:TBCM2838MailboxTagLayerResponse);`

BCM2838 mailbox tag get touch response

TBCM2838MailboxTagGetTouchResponse = record

Get Touch Buffer
`Address:LongWord;`

BCM2838 mailbox tag get touch

PBCM2838MailboxTagGetTouch = ^TBCM2838MailboxTagGetTouch;

TBCM2838MailboxTagGetTouch = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagGetTouchResponse);`

BCM2838 mailbox tag set touch request

TBCM2838MailboxTagSetTouchRequest = record

Set Touch Buffer
`Address:LongWord;`

BCM2838 mailbox tag set touch response

TBCM2838MailboxTagSetTouchResponse = record

`Status:LongWord;`

BCM2838 mailbox tag set touch

PBCM2838MailboxTagSetTouch = ^TBCM2838MailboxTagSetTouch;

TBCM2838MailboxTagSetTouch = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetTouchRequest);`
`1:(Response:TBCM2838MailboxTagSetTouchResponse);`

BCM2838 mailbox tag get virtual GPIO response

TBCM2838MailboxTagGetVirtualGPIOResponse = record

Get Virtual GPIO Buffer
`Address:LongWord;`

BCM2838 mailbox tag get virtual GPIO

PBCM2838MailboxTagGetVirtualGPIO = ^TBCM2838MailboxTagGetVirtualGPIO;

TBCM2838MailboxTagGetVirtualGPIO = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagGetVirtualGPIOResponse);`

BCM2838 mailbox tag set virtual GPIO request

TBCM2838MailboxTagSetVirtualGPIORequest = record

Set Virtual GPIO Buffer
`Address:LongWord;`

BCM2838 mailbox tag set virtual GPIO response

TBCM2876MailboxTagSetVirtualGPIOResponse = record

`Status:LongWord;`

BCM2838 mailbox tag set virtual GPIO

PBCM2838MailboxTagSetVirtualGPIO = ^TBCM2838MailboxTagSetVirtualGPIO;

TBCM2838MailboxTagSetVirtualGPIO = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetVirtualGPIORequest);`
`1:(Response:TBCM2876MailboxTagSetVirtualGPIOResponse);`

BCM2838 mailbox tag test vsync

PBCM2838MailboxTagTestVsync = ^TBCM2838MailboxTagTestVsync;

TBCM2838MailboxTagTestVsync = record

Test Vsync
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagNoResponse);`

BCM2838 mailbox tag set vsync

PBCM2838MailboxTagSetVsync = ^TBCM2838MailboxTagSetVsync;

TBCM2838MailboxTagSetVsync = record

Set Vsync
`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagNoResponse);`

BCM2838 mailbox tag set backlight request

TBCM2838MailboxTagSetBacklightRequest = record

Set Backlight
`Brightness:LongWord;`

BCM2838 mailbox tag set backlight response

TBCM2838MailboxTagSetBacklightResponse = record

`Brightness:LongWord;`

BCM2838 mailbox tag set backlight

PBCM2838MailboxTagSetBacklight = ^TBCM2838MailboxTagSetBacklight;

TBCM2838MailboxTagSetBacklight = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetBacklightRequest);`
`1:(Response:TBCM2838MailboxTagSetBacklightResponse);`

BCM2838 mailbox tag get display id request

TBCM2838MailboxTagGetDisplayIdRequest = record

Get Display Id
`DisplayNum:LongWord;`

BCM2838 mailbox tag get display id response

TBCM2838MailboxTagGetDisplayIdResponse = record

`DisplayId:LongWord;`

BCM2838 mailbox tag get display id

PBCM2838MailboxTagGetDisplayId = ^TBCM2838MailboxTagGetDisplayId;

TBCM2838MailboxTagGetDisplayId = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetDisplayIdRequest);`
`1:(Response:TBCM2838MailboxTagGetDisplayIdResponse);`

BCM2838 mailbox tag set display number request

TBCM2838MailboxTagSetDisplayNumRequest = record

Set Display Num
`DisplayNum:LongWord;`

BCM2838 mailbox tag set display number response

TBCM2838MailboxTagSetDisplayNumResponse = record

`DisplayNum:LongWord;`

BCM2838 mailbox tag set display number

PBCM2838MailboxTagSetDisplayNum = ^TBCM2838MailboxTagSetDisplayNum;

TBCM2838MailboxTagSetDisplayNum = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetDisplayNumRequest);`
`1:(Response:TBCM2838MailboxTagSetDisplayNumResponse);`

BCM2838 mailbox tag get number displays request

TBCM2838MailboxTagGetNumDisplaysRequest = record

Get Num Displays
`NumDisplays:LongWord;`

BCM2838 mailbox tag get number displays response

TBCM2838MailboxTagGetNumDisplaysResponse = record

`NumDisplays:LongWord;`

BCM2838 mailbox tag get number displays

PBCM2838MailboxTagGetNumDisplays = ^TBCM2838MailboxTagGetNumDisplays;

TBCM2838MailboxTagGetNumDisplays = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetNumDisplaysRequest);`
`1:(Response:TBCM2838MailboxTagGetNumDisplaysResponse);`

BCM2838 mailbox tag get display settings request

TBCM2838MailboxTagGetDisplaySettingsRequest = record

Get Display Settings
`DisplayNum:LongWord;`
`Width:LongWord;`
`Height:LongWord;`
`Depth:LongWord;`
`Pitch:LongWord;`
`VirtualWidth:LongWord;`
`VirtualHeight:LongWord;`
`VirtualWidthOffset:LongWord;`
`VirtualHeightOffset:LongWord;`
`BusAddress:LongWord;`

BCM2838 mailbox tag get display settings response

TBCM2838MailboxTagGetDisplaySettingsResponse = record

`DisplayNum:LongWord;`
`Width:LongWord;`
`Height:LongWord;`
`Depth:LongWord;`
`Pitch:LongWord;`
`VirtualWidth:LongWord;`
`VirtualHeight:LongWord;`
`VirtualWidthOffset:LongWord;`
`VirtualHeightOffset:LongWord;`
`BusAddress:LongWord;`

BCM2838 mailbox tag get display settings

PBCM2838MailboxTagGetDisplaySettings = ^TBCM2838MailboxTagGetDisplaySettings;

TBCM2838MailboxTagGetDisplaySettings = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagGetDisplaySettingsRequest);`
`1:(Response:TBCM2838MailboxTagGetDisplaySettingsResponse);`

BCM2838 mailbox tag set cursor info request

TBCM2838MailboxTagSetCursorInfoRequest = record

Set Cursor Info
`Width:LongWord;`	Pixels
`Height:LongWord;`	Pixels
`Reserved:LongWord;`
`Pixels:Pointer;`	Format is 32bpp (ARGB) (Width and Height should be >= 16 and (Width * Height) <= 64)
`HotspotX:LongWord;`
`HotspotY:LongWord;`

BCM2838 mailbox tag cursor response

TBCM2838MailboxTagCursorResponse = record

`Status:LongWord;`

BCM2838 mailbox tag set cursor info

PBCM2838MailboxTagSetCursorInfo = ^TBCM2838MailboxTagSetCursorInfo;

TBCM2838MailboxTagSetCursorInfo = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetCursorInfoRequest);`
`1:(Response:TBCM2838MailboxTagCursorResponse);`

BCM2838 mailbox tag set cursor state request

TBCM2838MailboxTagSetCursorStateRequest = record

Set Cursor State
`Enable:LongWord;`
`X:LongWord;`	Pixels
`Y:LongWord;`	Pixels
`Flags:LongWord;`

BCM2838 mailbox tag set cursor state

PBCM2838MailboxTagSetCursorState = ^TBCM2838MailboxTagSetCursorState;

TBCM2838MailboxTagSetCursorState = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagSetCursorStateRequest);`
`1:(Response:TBCM2838MailboxTagCursorResponse);`

BCM2838 mailbox tag VCHIQ init request

TBCM2838MailboxTagVCHIQInitRequest = record

VCHIQ Init
`Address:LongWord;`

BCM2838 mailbox tag VCHIQ init response

TBCM2838MailboxTagVCHIQInitResponse = record

`Status:LongWord;`	0 is Success

BCM2838 mailbox tag VCHIQ init

PBCM2838MailboxTagVCHIQInit = ^TBCM2838MailboxTagVCHIQInit;

TBCM2838MailboxTagVCHIQInit = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagVCHIQInitRequest);`
`1:(Response:TBCM2838MailboxTagVCHIQInitResponse);`

BCM2838 mailbox tag command line response

TBCM2838MailboxTagCommandLineResponse = record

Get Command Line
`CommandLine:array[0..1023] of Char;`

BCM2838 mailbox tag get command line

PBCM2838MailboxTagGetCommandLine = ^TBCM2838MailboxTagGetCommandLine;

TBCM2838MailboxTagGetCommandLine = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagCommandLineResponse);`

BCM2838 mailbox tag DMA channels response

TBCM2838MailboxTagDMAChannelsResponse = record

Get DMA Channels
`Channels:LongWord;`

BCM2838 mailbox tag get DMA channels

PBCM2838MailboxTagGetDMAChannels = ^TBCM2838MailboxTagGetDMAChannels;

TBCM2838MailboxTagGetDMAChannels = record

`Header:TBCM2838MailboxTagHeader;`
`case Integer of`
`0:(Request:TBCM2838MailboxTagNoRequest);`
`1:(Response:TBCM2838MailboxTagDMAChannelsResponse);`

BCM2838 mailbox tag create buffer

PBCM2838MailboxTagCreateBuffer = ^TBCM2838MailboxTagCreateBuffer;

TBCM2838MailboxTagCreateBuffer = record

Note: A combination tag to allocate and configure a framebuffer in one request
Create Buffer
`Physical:TBCM2838MailboxTagSetPhysical;`
`Vertual:TBCM2838MailboxTagSetVirtual;`
`Depth:TBCM2838MailboxTagSetDepth;`
`Order:TBCM2838MailboxTagSetPixelOrder;`
`Mode:TBCM2838MailboxTagSetAlphaMode;`
`Offset:TBCM2838MailboxTagSetVirtualOffset;`
`Overscan:TBCM2838MailboxTagSetOverscan;`
`Allocate:TBCM2838MailboxTagAllocateBuffer;`
`Pitch:TBCM2838MailboxTagGetPitch;`

BCM2838 mailbox tag query buffer

PBCM2838MailboxTagQueryBuffer = ^TBCM2838MailboxTagQueryBuffer;

TBCM2838MailboxTagQueryBuffer = record

Note: A combination tag to query all framebuffer properties in one request
Query Buffer
`Physical:TBCM2838MailboxTagGetPhysical;`
`Vertual:TBCM2838MailboxTagGetVirtual;`
`Depth:TBCM2838MailboxTagGetDepth;`
`Order:TBCM2838MailboxTagGetPixelOrder;`
`Mode:TBCM2838MailboxTagGetAlphaMode;`
`Offset:TBCM2838MailboxTagGetVirtualOffset;`
`Overscan:TBCM2838MailboxTagGetOverscan;`
`Pitch:TBCM2838MailboxTagGetPitch;`

BCM2838 ARM local mailbox write registers

PBCM2838ARMLocalMailboxWriteRegisters = ^TBCM2838ARMLocalMailboxWriteRegisters;

TBCM2838ARMLocalMailboxWriteRegisters = record

Note: BCM2838 ARM local structures (See: BCM2711 ARM Peripherals)
`Mailbox0Write:LongWord;`	Mailbox 0 write-set (WO)
`Mailbox1Write:LongWord;`	Mailbox 1 write-set (WO)
`Mailbox2Write:LongWord;`	Mailbox 2 write-set (WO)
`Mailbox3Write:LongWord;`	Mailbox 3 write-set (WO)

BCM2838 ARM local mailbox read clear registers

PBCM2838ARMLocalMailboxReadClearRegisters = ^TBCM2838ARMLocalMailboxReadClearRegisters;

TBCM2838ARMLocalMailboxReadClearRegisters = record

`Mailbox0ReadClear:LongWord;`	Mailbox 0 read & write-high-to-clear
`Mailbox1ReadClear:LongWord;`	Mailbox 1 read & write-high-to-clear
`Mailbox2ReadClear:LongWord;`	Mailbox 2 read & write-high-to-clear
`Mailbox3ReadClear:LongWord;`	Mailbox 3 read & write-high-to-clear

BCM2838 ARM local registers

PBCM2838ARMLocalRegisters = ^TBCM2838ARMLocalRegisters;

TBCM2838ARMLocalRegisters = record

`Control:LongWord;`	Control register $0000
`Reserved1:LongWord;`	Unused $0004
`CoreTimerPrescaler:LongWord;`	Core timer prescaler $0008
`CoreInterruptRouting:LongWord;`	Core Interrupts routing $000C
`PMInterruptRoutingSet:LongWord;`	Performance Monitor Interrupts routing-set $0010
`PMInterruptRoutingClear:LongWord;`	Performance Monitor Interrupts routing-clear $0014
`Reserved2:LongWord;`	Unused $0018
`CoreTimerLow:LongWord;`	Core timer access LS 32 bits $001C
`CoreTimerHigh:LongWord;`	Core timer access MS 32 bits $0020
`PeripheralIntRouting0:LongWord;`	Peripheral Interrupts 0-7 routing (1 to 7 Unused) $0024
`PeripheralIntRouting1:LongWord;`	Peripheral Interrupts 8-15 routing (Unused) $0028
`AXIOutstandingCount:LongWord;`	AXI outstanding counters $002C
`AXIOutstandingIRQ:LongWord;`	AXI outstanding IRQ $0030
`LocalTimerControl:LongWord;`	Local timer control & status $0034
`LocalTimerClearReload:LongWord;`	Local timer IRQ clear & reload $0038
`Reserved3:LongWord;`	Unused $003C
`TimersIntControl:array[0..BCM2838_CPU_COUNT - 1] of LongWord;`	Core0-3 Timers Interrupt control $0040-004C
`MailboxIntControl:array[0..BCM2838_CPU_COUNT - 1] of LongWord;`	Core0-3 Mailboxes Interrupt control $0050-005C
`IRQSource:array[0..BCM2838_CPU_COUNT - 1] of LongWord;`	Core0-3 IRQ Source $0060-006C
`FIQSource:array[0..BCM2838_CPU_COUNT - 1] of LongWord;`	Core0-3 FIQ Source $0070-007C
`MailboxWrite:array[0..BCM2838_CPU_COUNT - 1] of TBCM2838ARMLocalMailboxWriteRegisters;`	Core0-3 Mailbox 0-3 write-set (WO) $0080-00BC
`MailboxReadClear:array[0..BCM2838_CPU_COUNT - 1] of TBCM2838ARMLocalMailboxReadClearRegisters;`	Core0-3 Mailbox 0-3 read & write-high-to-clear $00C0-00FC

BCM2838 virtual GPIO buffer

PBCM2838VirtualGPIOBuffer = ^TBCM2838VirtualGPIOBuffer;

TBCM2838VirtualGPIOBuffer = record

`Buffer:Pointer;`
`Address:PtrUInt;`
`CachedBuffer:LongBool;`
`EnableDisable:array[0..BCM2838_VIRTUAL_GPIO_PIN_COUNT - 1] of LongWord;`	Two packed 16-bit counts of enabled and disabled / Allows host to detect a brief enable that was missed

Public variables

None defined

Function declarations

None defined

Return to Unit Reference

`BCM2838_VCBUS_0_ALIAS = $00000000;`	0 Alias - L1 and L2 cached
`BCM2838_VCBUS_4_ALIAS = $40000000;`	4 Alias - L2 cache coherent (non allocating)
`BCM2838_VCBUS_8_ALIAS = $80000000;`	8 Alias - L2 cached (only)
`BCM2838_VCBUS_C_ALIAS = $C0000000;`	C Alias - Direct uncached (Suitable for RPi 4 Model B)

`BCM2838_PERIPHERALS_BASE = $FE000000;`	Mapped to VC legacy address 7E000000
`BCM2838_PERIPHERALS_SIZE = SIZE_16M + SIZE_8M;`	24M

Unit BCM2838

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

`BCM2838_EXT_PERIPHERALS_BASE = $FC000000;`	Mapped to VC legacy address 7C000000
`BCM2838_EXT_PERIPHERALS_SIZE = SIZE_32M;`

`BCM2838_PCI_OUTBOUND_BASE = $F8000000;`
`BCM2838_PCI_OUTBOUND_SIZE = SIZE_64M;`

`BCM2838_PCI_INBOUND_BASE = $00000000;`
`BCM2838_PCI_INBOUND_SIZE = SIZE_4G;`	Limited to 3GB on some revisions