Unit BCM2838

From Ultibo.org
Revision as of 03:45, 30 August 2021 by Ultibo (Talk | contribs)

Jump to: navigation, search

Return to Unit Reference


Description


Ultibo Definitions specific to the Broadcom 2838 System on chip

The BCM2838 is the SoC used by the Raspberry Pi models 4B/400/CM4, it is often also referred to as the BCM2711 but for consistency with the earlier models we use that number for the core driver unit BCM2711.

Constants



BCM2838 specific constants BCM2838_*
BCM2838_CPU_COUNT = 4;  


BCM2838 ARM physical to VC legacy IO mapping BCM2838_VCIO_*
BCM2838_VCIO_ALIAS = $7E000000;  


BCM2838 ARM physical to VC legacy bus mapping BCM2838_VCBUS_*
BCM2838_VCBUS_0_ALIAS = $00000000; 0 Alias - L1 and L2 cached
BCM2838_VCBUS_4_ALIAS = $40000000; 4 Alias - L2 cache coherent (non allocating)
BCM2838_VCBUS_8_ALIAS = $80000000; 8 Alias - L2 cached (only)
BCM2838_VCBUS_C_ALIAS = $C0000000; C Alias - Direct uncached (Suitable for RPi 4 Model B)


BCM2838 physical memory addresses of BCM2838 peripheral BCM2838_PERIPHERALS_*
BCM2838_PERIPHERALS_BASE = $FE000000; Mapped to VC legacy address 7E000000
BCM2838_PERIPHERALS_SIZE = SIZE_16M + SIZE_8M; 24M


BCM2838 physical memory addresses of BCM2838 extended peripheral (GENET, PCIe) BCM2838_EXT_PERIPHERALS_*
BCM2838_EXT_PERIPHERALS_BASE = $FC000000; Mapped to VC legacy address 7C000000
BCM2838_EXT_PERIPHERALS_SIZE = SIZE_32M;  


BCM2838 physical memory address of BCM2839 PCIe address space BCM2838_PCI_ADDRESS_*
BCM2838_PCI_ADDRESS_BASE = $600000000;  
BCM2838_PCI_ADDRESS_SIZE = SIZE_64M;  


BCM2838 address of PCI outbound address space (Mapped to Physical PCIe address space) BCM2838_PCI_OUTBOUND_*
BCM2838_PCI_OUTBOUND_BASE = $F8000000;  
BCM2838_PCI_OUTBOUND_SIZE = SIZE_64M;  


BCM2838 address of PCI inbound address space BCM2838_PCI_INBOUND_*
BCM2838_PCI_INBOUND_BASE = $00000000;  
BCM2838_PCI_INBOUND_SIZE = SIZE_4G; Limited to 3GB on some revisions


BCM2838 system timer BCM2838_SYSTEM_TIMER_*
BCM2838_SYSTEM_TIMER_REGS_BASE = BCM2838_PERIPHERALS_BASE + $3000;  


BCM2838 DMA controller BCM2838_DMA*
Channels 0 to 14
 
BCM2838_DMA0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7000;  
BCM2838_DMA1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7100;  
BCM2838_DMA2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7200;  
BCM2838_DMA3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7300;  
BCM2838_DMA4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7400;  
BCM2838_DMA5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7500;  
BCM2838_DMA6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7600;  
BCM2838_DMA7_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7700; Lite DMA engine
BCM2838_DMA8_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7800; Lite DMA engine
BCM2838_DMA9_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7900; Lite DMA engine
BCM2838_DMA10_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7A00; Lite DMA engine
BCM2838_DMA11_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7B00; 40bit DMA engine (DMA channel 11 is able to access the PCIe interface)
BCM2838_DMA12_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7C00; 40bit DMA engine
BCM2838_DMA13_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7D00; 40bit DMA engine
BCM2838_DMA14_REGS_BASE = BCM2838_PERIPHERALS_BASE + $7E00; 40bit DMA engine
 
BCM2838_DMA_INT_STATUS_BASE = BCM2838_PERIPHERALS_BASE + $7FE0;  
BCM2838_DMA_ENABLE_BASE = BCM2838_PERIPHERALS_BASE + $7FF0;  


BCM2838 ARM legacy interrupt controller BCM2838_INTERRUPT_REGS_*
BCM2838_INTERRUPT_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B200; Note: Documentation states 0xB000 but the offsets begin at 0x200 so 0xB200 will be correct


BCM2838 ARM timer BCM2838_TIMER_REGS_*
BCM2838_TIMER_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B400; Note: Documentation states 0xB000 but the offsets begin at 0x400 so 0xB400 will be correct


BCM2838 ARM doorbell (VCHIQ) BCM2838_DOORBELL_*
BCM2838_DOORBELL_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B840;  
BCM2838_VCHIQ_REGS_BASE = BCM2838_DOORBELL_REGS_BASE;  


BCM2838 ARM mailbox 0 BCM2838_MAILBOX0_*
BCM2838_MAILBOX0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B880;  


BCM2838 ARM mailbox 1 BCM2838_MAILBOX1_*
BCM2838_MAILBOX1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B8A0;  


BCM2838 power management, reset controller and watchdog BCM2838_PM_*
BCM2838_PM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $100000;  


BCM2838 clock management BCM2838_CM_*
BCM2838_CM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $101000;  


BCM2838 PCM clock BCM2838_PCM_CLOCK_*
BCM2838_PCM_CLOCK_BASE = BCM2838_PERIPHERALS_BASE + $101098;  


BCM2838 random number generator BCM2838_RNG_REGS_*
BCM2838_RNG_REGS_BASE = BCM2838_PERIPHERALS_BASE + $104000;  


BCM2838 GPIO BCM2838_GPIO_*
BCM2838_GPIO_REGS_BASE = BCM2838_PERIPHERALS_BASE + $200000; This is shown in BCM2711 ARM Peripherals as 0x7E215000 which is thought to be an error


BCM2838 UART0 (PL011) BCM2838_PL011_*
BCM2838_PL011_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201000;  
BCM2838_UART0_REGS_BASE = BCM2838_PL011_REGS_BASE;  


BCM2838 UART2 (PL011) BCM2838_UART2_*
BCM2838_UART2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201400;  


BCM2838 UART3 (PL011) BCM2838_UART3_*
BCM2838_UART3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201600;  


BCM2838 UART4 (PL011) BCM2838_UART4_*
BCM2838_UART4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201800;  


BCM2838 UART5 (PL011) BCM2838_UART5_*
BCM2838_UART5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $201A00;  
 
BCM2838_UART0_REGS_BASES:array[0..5] of LongWord = (BCM2838_UART0_REGS_BASE, 0, BCM2838_UART2_REGS_BASE, BCM2838_UART3_REGS_BASE, BCM2838_UART4_REGS_BASE, BCM2838_UART5_REGS_BASE);


BCM2838 EMMC1 (SDHOST) BCM2838_EMMC1_*
BCM2838_EMMC1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $202000;  
BCM2838_SDHOST_REGS_BASE = BCM2838_EMMC1_REGS_BASE;  


BCM2838 PCM/I2S audio BCM2838_PCM_REGS_*
BCM2838_PCM_REGS_BASE = BCM2838_PERIPHERALS_BASE + $203000;  


BCM2838 SPI0 BCM2838_SPI0_*
BCM2838_SPI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204000;  


BCM2838 SPI3 BCM2838_SPI3_*
BCM2838_SPI3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204600;  


BCM2838 SPI4 BCM2838_SPI4_*
BCM2838_SPI4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204800;  


BCM2838 SPI5 BCM2838_SPI5_*
BCM2838_SPI5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204A00;  


BCM2838 SPI6 BCM2838_SPI6_*
BCM2838_SPI6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204C00;  
 
BCM2838_SPI0_REGS_BASES:array[0..6] of LongWord = (BCM2838_SPI0_REGS_BASE, 0, 0, BCM2838_SPI3_REGS_BASE, BCM2838_SPI4_REGS_BASE, BCM2838_SPI5_REGS_BASE, BCM2838_SPI6_REGS_BASE);


BCM2838 peripheral control BCM2838_PACTL_CS*
BCM2838_PACTL_CS_REGS_BASE = BCM2838_PERIPHERALS_BASE + $204E00;  


BCM2838 BSC0 (I2C0) (Broadcom Serial Controller) BCM2838_BSC0_*
BCM2838_BSC0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205000;  
BCM2838_I2C0_REGS_BASE = BCM2838_BSC0_REGS_BASE;  


BCM2838 I2C3 BCM2838_I2C3_*
BCM2838_I2C3_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205600;  


BCM2838 I2C4 BCM2838_I2C4_*
BCM2838_I2C4_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205800;  


BCM2838 I2C5 BCM2838_I2C5_*
BCM2838_I2C5_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205A00; Note: This is shown in BCM2711 ARM Peripherals as 0x7E205A80 which is thought to be an error


BCM2838 I2C6 BCM2838_I2C6_*
BCM2838_I2C6_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205C00;  


BCM2838 I2C7 BCM2838_I2C7_*
Note: I2C7 master is used dedicated with the HDMI interface and must not be used
 
BCM2838_I2C7_REGS_BASE = BCM2838_PERIPHERALS_BASE + $205E00;  


BCM2838 pixel valve BCM2838_PIXELVALVE0_*
BCM2838_PIXELVALVE0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $206000; Pixel Valve 0
BCM2838_PIXELVALVE1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $207000; Pixel Valve 1


BCM2838 DPI (Display Parallel Interface) BCM2838_DPI_*
BCM2838_DPI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $208000;  


BCM2838 DSI0 (Display Serial Interface) BCM2838_DSI0_*
BCM2838_DSI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $209000;  


BCM2838 PWM0 (Pulse Width Modulator) BCM2838_PWM0_*
BCM2838_PWM0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $20C000;  


BCM2838 PWM1 (Pulse Width Modulator) BCM2838_PWM1_*
BCM2838_PWM1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $20C800;  
BCM2838_PWM0_REGS_BASES:array[0..1] of LongWord = (BCM2838_PWM0_REGS_BASE, BCM2838_PWM1_REGS_BASE);


BCM2838 I2C/SPI slave BCM2838_I2CSPI_*
BCM2838_I2CSPI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $214000;  


BCM2838 AUX (UART1, SPI1 and SPI2) BCM2838_AUX_*
BCM2838_AUX_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215000;  
BCM2838_UART1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215040;  
BCM2838_SPI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $215080;  
BCM2838_SPI2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $2150C0;  


BCM2838 EMMC0 (SDHCI) BCM2838_EMMC0_*
BCM2838_EMMC0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $300000;  
BCM2838_SDHCI_REGS_BASE = BCM2838_EMMC0_REGS_BASE;  


BCM2838 EMMC2 BCM2838_EMMC2_*
BCM2838_EMMC2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $340000;  


BCM2838 HVS BCM2838_HVS_*
BCM2838_HVS_REGS_BASE = BCM2838_PERIPHERALS_BASE + $400000;  


BCM2838 SMI (Firmware KMS) BCM2838_SMI_*
BCM2838_SMI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $600000;  
BCM2838_FIRMWAREKMS_REGS_BASE = BCM2838_SMI_REGS_BASE;  


BCM2838 DSI1 (Display Serial Interface) BCM2838_DSI1_*
BCM2838_DSI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $700000;  


BCM2838 CSI0 (Camera Serial Interface) BCM2838_CSI0_*
BCM2838_CSI0_REGS_BASE = BCM2838_PERIPHERALS_BASE + $800000;  


BCM2838 CSI1 (Camera Serial Interface) BCM2838_CSI1_*
BCM2838_CSI1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $801000;  


BCM2838 BSC1 (I2C1) (Broadcom Serial Controller) BCM2838_BSC1_*
BCM2838_BSC1_REGS_BASE = BCM2838_PERIPHERALS_BASE + $804000;  
BCM2838_I2C1_REGS_BASE = BCM2838_BSC1_REGS_BASE;  


BCM2838 BSC2 (I2C2) (Broadcom Serial Controller) BCM2838_BSC2_*
Note: I2C2 master is used dedicated with the HDMI interface and must not be used
 
BCM2838_BSC2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $805000;  
BCM2838_I2C2_REGS_BASE = BCM2838_BSC2_REGS_BASE;  
BCM2838_I2C0_REGS_BASES:array[0..7] of LongWord = (BCM2838_I2C0_REGS_BASE, BCM2838_I2C1_REGS_BASE, BCM2838_I2C2_REGS_BASE, BCM2838_I2C3_REGS_BASE, BCM2838_I2C4_REGS_BASE, BCM2838_I2C5_REGS_BASE, BCM2838_I2C6_REGS_BASE, BCM2838_I2C7_REGS_BASE);


BCM2838 VEC BCM2838_VEC_*
BCM2838_VEC_REGS_BASE = BCM2838_PERIPHERALS_BASE + $806000;  


BCM2838 pixel valve 2 BCM2838_PIXELVALVE2_*
BCM2838_PIXELVALVE2_REGS_BASE = BCM2838_PERIPHERALS_BASE + $807000;  


BCM2838 HDMI BCM2838_HDMI_*
BCM2838_HDMI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $902000;  


BCM2838 USB (Synopsys DesignWare Hi-Speed USB 2.0 On-The-Go Controller) BCM2838_USB_*
BCM2838_USB_REGS_BASE = BCM2838_PERIPHERALS_BASE + $980000;  
BCM2838_DWCOTG_REGS_BASE = BCM2838_USB_REGS_BASE;  


BCM2838 XHCI (Additional on chip generic XHCI USB host controller) BCM2838_XHCI_*
BCM2838_XHCI_REGS_BASE = BCM2838_PERIPHERALS_BASE + $9C0000; This is separate to the VL805 XHCI controller


BCM2838 HEVC Decoder BCM2838_HEVC_*
BCM2838_HEVC_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B00000;  


BCM2838 ARGON BCM2838_ARGON_*
BCM2838_ARGON_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B10000;  


BCM2838 H264 decoder BCM 2838_H264_*
BCM 2838_H264_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B20000;  


BCM2838 VP9 decoder BCM2838_VP9_*
BCM2838_VP9_REGS_BASE = BCM2838_PERIPHERALS_BASE + $B30000;  


BCM2838 V3D BCM2838_V3D_*
BCM2838_V3D_REGS_BASE = BCM2838_PERIPHERALS_BASE + $C04000;  


BCM2838 DMA controller BCM2838_DMA15_*
Channel 15 Note: DMA15 is exclusively used by the VPU
 
BCM2838_DMA15_REGS_BASE = BCM2838_PERIPHERALS_BASE + $E05000;  


BCM2838 chip revision BCM2838_CHIP_REVISION_*
See: https://elinux.org/The_Undocumented_Pi#BCM2711
 
BCM2838_CHIP_REVISION_BASE = BCM2838_EXT_PERIPHERALS_BASE + $404000;  


BCM2838 PCIe BCM2838_PCIE_*
BCM2838_PCIE_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $1500000;  


BCM2838 GENET BCM2838_GENET_*
BCM2838_GENET_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $1580000;  
BCM2838_GENET_MDIO_OFFSET = $0E14;  


BCM2838 thermal BCM2838_THERMAL_*
BCM2838_THERMAL_REGS_BASE = BCM2838_EXT_PERIPHERALS_BASE + $15D2200;  


BCM2838 IRQ peripheral BCM2838_IRQ_*
IRQ lines of BCM2838 peripherals
 
BCM2838_SPI_BASE = 32; Added to the SPI ID in device tree to obtain the real ID
BCM2838_PPI_BASE = 16; Added to the PPI ID in device tree to obtain the real ID
BCM2838_SGI_BASE = 0;  
ARM Generic Timer
BCM2838_IRQ_TIMER0 = BCM2838_PPI_BASE + 13; IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n PS timer IRQ)
BCM2838_IRQ_TIMER1 = BCM2838_PPI_BASE + 14; IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n PNS timer IRQ)
BCM2838_IRQ_TIMER2 = BCM2838_PPI_BASE + 11; IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n V timer IRQ)
BCM2838_IRQ_TIMER3 = BCM2838_PPI_BASE + 10; IRQ_TYPE_LEVEL_LOW / CPU_MASK_0 or CPU_MASK_1 or CPU_MASK_2 or CPU_MASK_3 (Core n HP timer IRQ)
Legacy IRQ/FIQ
BCM2838_FIQ_LEGACY = BCM2838_PPI_BASE + 12; Legacy FIQn
BCM2838_IRQ_LEGACY = BCM2838_PPI_BASE + 15; Legacy IRQn
ARM Mailbox IRQs (BCM2838_SPI_BASE + 0 to 15)
BCM2838_IRQ_MAILBOX0_0 = BCM2838_SPI_BASE + 0; IRQ_TYPE_LEVEL_HIGH(Core 0)
BCM2838_IRQ_MAILBOX1_0 = BCM2838_SPI_BASE + 1; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX2_0 = BCM2838_SPI_BASE + 2; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX3_0 = BCM2838_SPI_BASE + 3; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX0_1 = BCM2838_SPI_BASE + 4; IRQ_TYPE_LEVEL_HIGH (Core 1)
BCM2838_IRQ_MAILBOX1_1 = BCM2838_SPI_BASE + 5; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX2_1 = BCM2838_SPI_BASE + 6; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX3_1 = BCM2838_SPI_BASE + 7; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX0_2 = BCM2838_SPI_BASE + 8; IRQ_TYPE_LEVEL_HIGH (Core 2)
BCM2838_IRQ_MAILBOX1_2 = BCM2838_SPI_BASE + 9; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX2_2 = BCM2838_SPI_BASE + 10; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX3_2 = BCM2838_SPI_BASE + 11; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX0_3 = BCM2838_SPI_BASE + 12; IRQ_TYPE_LEVEL_HIGH (Core 3)
BCM2838_IRQ_MAILBOX1_3 = BCM2838_SPI_BASE + 13; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX2_3 = BCM2838_SPI_BASE + 14; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MAILBOX3_3 = BCM2838_SPI_BASE + 15; IRQ_TYPE_LEVEL_HIGH
ARM PMU
BCM2838_IRQ_PMU0 = BCM2838_SPI_BASE + 16; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PMU1 = BCM2838_SPI_BASE + 17; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PMU2 = BCM2838_SPI_BASE + 18; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PMU3 = BCM2838_SPI_BASE + 19; IRQ_TYPE_LEVEL_HIGH
AXI Quiet
BCM2838_IRQ_LOCAL_AXIQUIET = BCM2838_SPI_BASE + 20; IRQ_TYPE_LEVEL_HIGH
ARM Local Timer
BCM2838_IRQ_LOCAL_TIMER = BCM2838_SPI_BASE + 21; IRQ_TYPE_LEVEL_HIGH
AXI Error
BCM2838_IRQ_LOCAL_AXIERR = BCM2838_SPI_BASE + 22; IRQ_TYPE_LEVEL_HIGH (TBD)
ARM peripheral IRQs (BCM2838_SPI_BASE + 32 to 47)
ARM Timer
BCM2838_IRQ_ARM_TIMER = BCM2838_SPI_BASE + 32; IRQ_TYPE_LEVEL_HIGH
ARM Mailbox
BCM2838_IRQ_ARM_MAILBOX = BCM2838_SPI_BASE + 33; IRQ_TYPE_LEVEL_HIGH
ARM Doorbell (VCHIQ)
BCM2838_IRQ_ARM_DOORBELL0 = BCM2838_SPI_BASE + 34; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_DOORBELL1 = BCM2838_SPI_BASE + 35; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_VCHIQ = BCM2838_IRQ_ARM_DOORBELL0;  
ARM VPU Halted
BCM2838_IRQ_ARM_VPU0HALTED = BCM2838_SPI_BASE + 36; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_VPU1HALTED = BCM2838_SPI_BASE + 37; IRQ_TYPE_LEVEL_HIGH
ARM Error
BCM2838_IRQ_ARM_ADDRERROR = BCM2838_SPI_BASE + 38; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_AXIERROR = BCM2838_SPI_BASE + 39; IRQ_TYPE_LEVEL_HIGH
ARM Software Interrupt (SWI)
BCM2838_IRQ_ARM_SWI0 = BCM2838_SPI_BASE + 40; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI1 = BCM2838_SPI_BASE + 41; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI2 = BCM2838_SPI_BASE + 42; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI3 = BCM2838_SPI_BASE + 43; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI4 = BCM2838_SPI_BASE + 44; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI5 = BCM2838_SPI_BASE + 45; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI6 = BCM2838_SPI_BASE + 46; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_ARM_SWI7 = BCM2838_SPI_BASE + 47; IRQ_TYPE_LEVEL_HIGH
VC peripheral IRQs (BCM2838_SPI_BASE + 64 to 127)
System Timer
BCM2838_IRQ_SYSTEM_TIMER_0 = BCM2838_SPI_BASE + 64; Already used by the VideoCore GPU (Do not use)
BCM2838_IRQ_SYSTEM_TIMER_1 = BCM2838_SPI_BASE + 65;  
BCM2838_IRQ_SYSTEM_TIMER_2 = BCM2838_SPI_BASE + 66; Already used by the VideoCore GPU (Do not use)
BCM2838_IRQ_SYSTEM_TIMER_3 = BCM2838_SPI_BASE + 67;  
H264 Codec
BCM2838_IRQ_H264_0 = BCM2838_SPI_BASE + 68; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_H264_1 = BCM2838_SPI_BASE + 69; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_H264_2 = BCM2838_SPI_BASE + 70; IRQ_TYPE_LEVEL_HIGH
JPEG
BCM2838_IRQ_JPEG = BCM2838_SPI_BASE + 71; IRQ_TYPE_LEVEL_HIGH
ISP
BCM2838_IRQ_ISP = BCM2838_SPI_BASE + 72; IRQ_TYPE_LEVEL_HIGH
USB (Synopsys DesignWare Hi-Speed USB 2.0 On-The-Go Controller)
BCM2838_IRQ_USB = BCM2838_SPI_BASE + 73; IRQ_TYPE_LEVEL_HIGH
V3D
BCM2838_IRQ_V3D = BCM2838_SPI_BASE + 74; IRQ_TYPE_LEVEL_HIGH
Transposer
BCM2838_IRQ_TXP = BCM2838_SPI_BASE + 75; IRQ_TYPE_LEVEL_HIGH
Multicore Sync
BCM2838_IRQ_MULTICORESYNC0 = BCM2838_SPI_BASE + 76; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MULTICORESYNC1 = BCM2838_SPI_BASE + 77; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MULTICORESYNC2 = BCM2838_SPI_BASE + 78; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_MULTICORESYNC3 = BCM2838_SPI_BASE + 79; IRQ_TYPE_LEVEL_HIGH
DMA
BCM2838_IRQ_DMA0 = BCM2838_SPI_BASE + 80; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA1 = BCM2838_SPI_BASE + 81; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA2 = BCM2838_SPI_BASE + 82; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA3 = BCM2838_SPI_BASE + 83; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA4 = BCM2838_SPI_BASE + 84; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA5 = BCM2838_SPI_BASE + 85; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA6 = BCM2838_SPI_BASE + 86; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA7 = BCM2838_SPI_BASE + 87; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA8 = BCM2838_SPI_BASE + 87; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA9 = BCM2838_SPI_BASE + 88; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA10 = BCM2838_SPI_BASE + 88; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA11 = BCM2838_SPI_BASE + 89; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA12 = BCM2838_SPI_BASE + 90; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA13 = BCM2838_SPI_BASE + 91; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_DMA14 = BCM2838_SPI_BASE + 92; IRQ_TYPE_LEVEL_HIGH
 
BCM2838_IRQ_DMA7_8 = BCM2838_IRQ_DMA7;  
BCM2838_IRQ_DMA9_10 = BCM2838_IRQ_DMA9;  
AUX (UART1, SPI1 and SPI2)
BCM2838_IRQ_AUX = BCM2838_SPI_BASE + 93; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_UART1 = BCM2838_IRQ_AUX;  
BCM2838_IRQ_SPI1 = BCM2838_IRQ_AUX;  
BCM2838_IRQ_SPI2 = BCM2838_IRQ_AUX;  
ARM
BCM2838_IRQ_ARM = BCM2838_SPI_BASE + 94; IRQ_TYPE_LEVEL_HIGH
DMA Note: DMA15 is exclusively used by the VPU
BCM2838_IRQ_DMA15 = BCM2838_SPI_BASE + 95; IRQ_TYPE_LEVEL_HIGH
HDMI CEC
BCM2838_IRQ_HDMI_CEC = BCM2838_SPI_BASE + 96; IRQ_TYPE_LEVEL_HIGH
HVS
BCM2838_IRQ_HVS = BCM2838_SPI_BASE + 97; IRQ_TYPE_LEVEL_HIGH
ARGON (RPIVID)
BCM2838_IRQ_ARGON = BCM2838_SPI_BASE + 98; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_RPIVID = BCM2838_IRQ_ARGON;  
SDC
BCM2838_IRQ_SDC = BCM2838_SPI_BASE + 99; IRQ_TYPE_LEVEL_HIGH
DSI0
BCM2838_IRQ_DSI0 = BCM2838_SPI_BASE + 100; IRQ_TYPE_LEVEL_HIGH
Pixel Valve 2
BCM2838_IRQ_PIXELVALVE2 = BCM2838_SPI_BASE + 101; IRQ_TYPE_LEVEL_HIGH
CSI0 (Camera Serial Interface)
BCM2838_IRQ_CSI0 = BCM2838_SPI_BASE + 102; IRQ_TYPE_LEVEL_HIGH
CSI1 (Camera Serial Interface)
BCM2838_IRQ_CSI1 = BCM2838_SPI_BASE + 103; IRQ_TYPE_LEVEL_HIGH
HDMI
BCM2838_IRQ_HDMI_0 = BCM2838_SPI_BASE + 104; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_HDMI_1 = BCM2838_SPI_BASE + 105; IRQ_TYPE_LEVEL_HIGH
Pixel Valve 3
BCM2838_IRQ_PIXELVALVE3 = BCM2838_SPI_BASE + 106; IRQ_TYPE_LEVEL_HIGH
I2C / SPI Slave
BCM2838_IRQ_I2CSPI = BCM2838_SPI_BASE + 107; IRQ_TYPE_LEVEL_HIGH
DSI1
BCM2838_IRQ_DSI1 = BCM2838_SPI_BASE + 108; IRQ_TYPE_LEVEL_HIGH
Pixel Valve 0
BCM2838_IRQ_PIXELVALVE0 = BCM2838_SPI_BASE + 109; IRQ_TYPE_LEVEL_HIGH
Pixel Valve 1/4
BCM2838_IRQ_PIXELVALVE1 = BCM2838_SPI_BASE + 110; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PIXELVALVE4 = BCM2838_IRQ_PIXELVALVE1;  
CPR
BCM2838_IRQ_CPR = BCM2838_SPI_BASE + 111; IRQ_TYPE_LEVEL_HIGH
SMI (Firmware KMS)
BCM2838_IRQ_SMI = BCM2838_SPI_BASE + 112; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_FIRMWAREKMS = BCM2838_IRQ_SMI;  
GPIO
BCM2838_IRQ_GPIO_0 = BCM2838_SPI_BASE + 113; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_GPIO_1 = BCM2838_SPI_BASE + 114; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_GPIO_2 = BCM2838_SPI_BASE + 115; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_GPIO_3 = BCM2838_SPI_BASE + 116; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_GPIO_ALL = BCM2838_IRQ_GPIO_3;  
BSC0 (I2C0) (Broadcom Serial Controller)
BCM2838_IRQ_BSC0 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_I2C0 = BCM2838_IRQ_BSC0;  
BSC1 (I2C1) (Broadcom Serial Controller)
BCM2838_IRQ_BSC1 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_I2C1 = BCM2838_IRQ_BSC1;  
BSC2 (I2C2) (Broadcom Serial Controller)
BCM2838_IRQ_BSC2 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_I2C2 = BCM2838_IRQ_BSC2;  
I2C3
BCM2838_IRQ_I2C3 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
I2C4
BCM2838_IRQ_I2C4 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
I2C5
BCM2838_IRQ_I2C5 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
I2C6
BCM2838_IRQ_I2C6 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
I2C7
BCM2838_IRQ_I2C7 = BCM2838_SPI_BASE + 117; IRQ_TYPE_LEVEL_HIGH
BCM2838_I2C0_IRQS:array[0..7] of LongWord = (BCM2838_IRQ_I2C0, BCM2838_IRQ_I2C1, BCM2838_IRQ_I2C2, BCM2838_IRQ_I2C3, BCM2838_IRQ_I2C4, BCM2838_IRQ_I2C5, BCM2838_IRQ_I2C6, BCM2838_IRQ_I2C7);
SPI0
BCM2838_IRQ_SPI0 = BCM2838_SPI_BASE + 118; IRQ_TYPE_LEVEL_HIGH
SPI3
BCM2838_IRQ_SPI3 = BCM2838_SPI_BASE + 118; IRQ_TYPE_LEVEL_HIGH
SPI4
BCM2838_IRQ_SPI4 = BCM2838_SPI_BASE + 118; IRQ_TYPE_LEVEL_HIGH
SPI5
BCM2838_IRQ_SPI5 = BCM2838_SPI_BASE + 118; IRQ_TYPE_LEVEL_HIGH
SPI6
BCM2838_IRQ_SPI6 = BCM2838_SPI_BASE + 118; IRQ_TYPE_LEVEL_HIGH
BCM2838_SPI0_IRQS:array[0..6] of LongWord = (BCM2838_IRQ_SPI0, 0, 0, BCM2838_IRQ_SPI3, BCM2838_IRQ_SPI4, BCM2838_IRQ_SPI5, BCM2838_IRQ_SPI6);
I2S PCM sound
BCM2838_IRQ_I2SPCM = BCM2838_SPI_BASE + 119; IRQ_TYPE_LEVEL_HIGH
EMMC1 (SDHOST)
BCM2838_IRQ_EMMC1 = BCM2838_SPI_BASE + 120; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_SDHOST = BCM2838_IRQ_EMMC1;  
UART0 (PL011)
BCM2838_IRQ_PL011 = BCM2838_SPI_BASE + 121; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_UART0 = BCM2838_IRQ_PL011;  
UART2 (PL011)
BCM2838_IRQ_UART2 = BCM2838_SPI_BASE + 121; IRQ_TYPE_LEVEL_HIGH
UART3 (PL011)
BCM2838_IRQ_UART3 = BCM2838_SPI_BASE + 121; IRQ_TYPE_LEVEL_HIGH
UART4 (PL011)
BCM2838_IRQ_UART4 = BCM2838_SPI_BASE + 121; IRQ_TYPE_LEVEL_HIGH
UART5 (PL011)
BCM2838_IRQ_UART5 = BCM2838_SPI_BASE + 121; IRQ_TYPE_LEVEL_HIGH
BCM2838_UART0_IRQS:array[0..5] of LongWord = (BCM2838_IRQ_UART0, 0, BCM2838_IRQ_UART2, BCM2838_IRQ_UART3, BCM2838_IRQ_UART4, BCM2838_IRQ_UART5);
ETH_PCIe L2
BCM2838_IRQ_ETH_PCIE = BCM2838_SPI_BASE + 122; IRQ_TYPE_LEVEL_HIGH
VEC
BCM2838_IRQ_VEC = BCM2838_SPI_BASE + 123; IRQ_TYPE_LEVEL_HIGH
CPG
BCM2838_IRQ_CPG = BCM2838_SPI_BASE + 124; IRQ_TYPE_LEVEL_HIGH
Random Number Generator
BCM2838_IRQ_RNG = BCM2838_SPI_BASE + 125; IRQ_TYPE_LEVEL_HIGH
EMMC0 (SDHCI)
BCM2838_IRQ_EMMC0 = BCM2838_SPI_BASE + 126; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_SDHCI = BCM2838_IRQ_EMMC0;  
EMMC2 (SDHCI)
BCM2838_IRQ_EMMC2 = BCM2838_SPI_BASE + 126; IRQ_TYPE_LEVEL_HIGH
ETH_PCIe Secure
BCM2838_IRQ_ETH_PCIE_SEC = BCM2838_SPI_BASE + 127; IRQ_TYPE_LEVEL_HIGH
ETH_PCIe L2 IRQs (BCM2838_SPI_BASE + 128 to 184)
Thermal (AVS)
BCM2838_IRQ_THERMAL = BCM2838_SPI_BASE + 137; IRQ_TYPE_LEVEL_HIGH
PCIe
BCM2838_IRQ_PCIE_INTA = BCM2838_SPI_BASE + 143; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PCIE_INTB = BCM2838_SPI_BASE + 144; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PCIE_INTC = BCM2838_SPI_BASE + 145; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PCIE_INTD = BCM2838_SPI_BASE + 146; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_PCIE_MSI = BCM2838_SPI_BASE + 148; IRQ_TYPE_LEVEL_HIGH
GENET
BCM2838_IRQ_GENET_0 = BCM2838_SPI_BASE + 157; IRQ_TYPE_LEVEL_HIGH
BCM2838_IRQ_GENET_1 = BCM2838_SPI_BASE + 158; IRQ_TYPE_LEVEL_HIGH
XHCI (Additional on chip generic XHCI USB host controller)
BCM2838_IRQ_XHCI = BCM2838_SPI_BASE + 176; IRQ_TYPE_LEVEL_HIGH (This is separate to the VL805 XHCI controller)
Number of shared IRQs
BCM2838_SHARED_IRQ_COUNT = 988; SPI 32-1019
Number of private IRQs
BCM2838_PRIVATE_IRQ_COUNT = 16; PPI 16-31
Number of software IRQs
BCM2838_SOFTWARE_IRQ_COUNT = 16; SGI 0-15
Number of reserved IRQs
BCM2838_RESERVED_IRQ_COUNT = 4; ID 1020-1023
Total number of IRQs available
BCM2838_IRQ_COUNT = BCM2838_SHARED_IRQ_COUNT + BCM2838_PRIVATE_IRQ_COUNT + BCM2838_SOFTWARE_IRQ_COUNT + BCM2838_RESERVED_IRQ_COUNT;
Total number of FIQs available
BCM2838_FIQ_COUNT = BCM2838_IRQ_COUNT;  


BCM2838 system timer frequency BCM2838_SYSTEM_TIMER_BCM2838_SYSTEM_TIMER_FREQUENCY*
BCM2838_SYSTEM_TIMER_FREQUENCY = 1000000; Default clock frequency of the BCM2838 System Timer (1MHz)


BCM2838 system timer control/status BCM2838_SYSTEM_TIMER_CS_*
See: Section 12
 
BCM2838_SYSTEM_TIMER_CS_0 = (1 shl 0); Already used by the VideoCore GPU (Do not use)
BCM2838_SYSTEM_TIMER_CS_1 = (1 shl 1);  
BCM2838_SYSTEM_TIMER_CS_2 = (1 shl 2); Already used by the VideoCore GPU (Do not use)
BCM2838_SYSTEM_TIMER_CS_3 = (1 shl 3);  


BCM2838 DMA control/status BCM2838_DMA_CS_*
See: Section 4
 
BCM2838_DMA_CS_ACTIVE = (1 shl 0); Activate the DMA (This bit enables the DMA. The DMA will start if this bit is set and the CB_ADDR is non zero. The DMA transfer can be paused and resumed by clearing, then setting it again.)
BCM2838_DMA_CS_END = (1 shl 1); DMA End Flag (Set when the transfer described by the current control block is complete. Write 1 to clear.)
BCM2838_DMA_CS_INT = (1 shl 2); Interrupt Status (This is set when the transfer for the CB ends and INTEN is set to 1. Write 1 to clear.)
BCM2838_DMA_CS_DREQ = (1 shl 3); DREQ State (Indicates the state of the selected DREQ (Data Request) signal, ie. the DREQ selected by the PERMAP field of the transfer info.)
BCM2838_DMA_CS_PAUSED = (1 shl 4); DMA Paused State (Indicates if the DMA is currently paused and not transferring data)
BCM2838_DMA_CS_DREQ_PAUSED = (1 shl 5); DMA Paused by DREQ State (Indicates if the DMA is currently paused and not transferring data due to the DREQ being inactive)
BCM2838_DMA_CS_WAITING_FOR_OUTSTANDING_WRITES = (1 shl 6); DMA is Waiting for the Last Write to be Received (Indicates if the DMA is currently waiting for any outstanding writes to be received, and is not transferring data.)
Bit 7 Reserved - Write as 0, read as don't care
BCM2838_DMA_CS_ERROR = (1 shl 8); DMA Error (Indicates if the DMA has detected an error)
BCM2838_DMA_CS_PRIORITY = ($F shl 16); AXI Priority Level (Sets the priority of normal AXI bus transactions. Zero is the lowest priority.)
BCM2838_DMA_CS_PANIC_PRIORITY = ($F shl 20); AXI Panic Priority Level (Sets the priority of panicking AXI bus transactions)
Bits 24:27 Reserved - Write as 0, read as don't care
BCM2838_DMA_CS_WAIT_FOR_OUTSTANDING_WRITES = (1 shl 28); Wait for outstanding writes (When set to 1, the DMA will keep a tally of the AXI writes going out and the write responses coming in.)
BCM2838_DMA_CS_DISDEBUG = (1 shl 29); Disable debug pause signal (When set to 1, the DMA will not stop when the debug pause signal is asserted.)
BCM2838_DMA_CS_ABORT = (1 shl 30); Abort DMA (Writing a 1 to this bit will abort the current DMA CB. The DMA will load the next CB and attempt to continue. The bit cannot be read, and will self clear.)
BCM2838_DMA_CS_RESET = (1 shl 31); DMA Channel Reset (Writing a 1 to this bit will reset the DMA. The bit cannot be read, and will self clear.)
 
BCM2838_DMA_CS_PRIORITY_DEFAULT = 0;  


BCM2838 DMA transfer information BCM2838_DMA_TI_*
See: Section 4
 
BCM2838_DMA_TI_INTEN = (1 shl 0); Interrupt Enable (1 = Generate an interrupt when the transfer described by the current Control Block completes)
BCM2838_DMA_TI_2DMODE = (1 shl 1); 2D Mode (1 = 2D mode interpret the TXFR_LEN register as YLENGTH number of transfers each of XLENGTH, and add the strides to the address after each transfer.)
Bit 2 Reserved - Write as 0, read as don't care
BCM2838_DMA_TI_WAIT_RESP = (1 shl 3); Wait for a Write Response (When set this makes the DMA wait until it receives the AXI write response for each write. This ensures that multiple writes cannot get stacked in the AXI bus pipeline.)
BCM2838_DMA_TI_DEST_INC = (1 shl 4); Destination Address Increment (1 = Destination address increments after each write. The address will increment by 4, if DEST_WIDTH=0 else by 32.)
BCM2838_DMA_TI_DEST_WIDTH = (1 shl 5); Destination Transfer Width (1 = Use 128-bit destination write width. 0 = Use 32-bit destination write width.)
BCM2838_DMA_TI_DEST_DREQ = (1 shl 6); Control Destination Writes with DREQ (1 = The DREQ selected by PERMAP will gate the destination writes)
BCM2838_DMA_TI_DEST_IGNORE = (1 shl 7); Ignore Writes (1 = Do not perform destination writes. 0 = Write data to destination.)
BCM2838_DMA_TI_SRC_INC = (1 shl 8); Source Address Increment (1 = Source address increments after each read. The address will increment by 4, if S_WIDTH=0 else by 32.)
BCM2838_DMA_TI_SRC_WIDTH = (1 shl 9); Source Transfer Width (1 = Use 128-bit source read width. 0 = Use 32-bit source read width.)
BCM2838_DMA_TI_SRC_DREQ = (1 shl 10); Control Source Reads with DREQ (1 = The DREQ selected by PERMAP will gate the source reads)
BCM2838_DMA_TI_SRC_IGNORE = (1 shl 11); Ignore Reads (1 = Do not perform source reads. In addition, destination writes will zero all the write strobes. This is used for fast cache fill operations.)
BCM2838_DMA_TI_BURST_LENGTH = ($F shl 12); Burst Transfer Length (Indicates the burst length of the DMA transfers)
BCM2838_DMA_TI_PERMAP = ($1F shl 16); Peripheral Mapping (Indicates the peripheral number (1-31) whose ready signal shall be used to control the rate of the transfers)
BCM2838_DMA_TI_WAITS = ($3E shl 21); Add Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles burnt after each DMA read or write operation is completed)
BCM2838_DMA_TI_NO_WIDE_BURSTS = (1 shl 26); Don't Do wide writes as a 2 beat burst (This prevents the DMA from issuing wide writes as 2 beat AXI bursts. This is an inefficient access mode, so the default is to use the bursts.)
Bits 27:31 Reserved - Write as 0, read as don't care
 
Note: BCM2838_DMA_TI_2DMODE, BCM2838_DMA_TI_DEST_IGNORE, BCM2838_DMA_TI_SRC_IGNORE and BCM2838_DMA_TI_NO_WIDE_BURSTS not available on DMA Lite channels
 
BCM2838_DMA_TI_PERMAP_SHIFT = 16;  
BCM2838_DMA_TI_BURST_LENGTH_SHIFT = 12;  
 
BCM2838_DMA_TI_BURST_LENGTH_DEFAULT = 0;  


BCM2838 DMA transfer length BCM2838_DMA_TXFR_LEN_*
See: Section 4
 
BCM2838_DMA_TXFR_LEN_XLENGTH = ($FFFF shl 0); Transfer Length in bytes
BCM2838_DMA_TXFR_LEN_YLENGTH = ($3FFF shl 16); When in 2D mode, This is the Y transfer length, indicating how many xlength transfers are performed. When in normal linear mode this becomes the top bits of the XLENGTH.
 
Note: BCM2838_DMA_TXFR_LEN_YLENGTH not available on DMA Lite channels


BCM2838 DMA 2D stride BCM2838_DMA_STRIDE_*
See: Section 4
 
BCM2838_DMA_STRIDE_S_STRIDE = ($FFFF shl 0); Destination Stride (2D Mode) (Signed (2 s complement) byte increment to apply to the destination address at the end of each row in 2D mode)
BCM2838_DMA_STRIDE_D_STRIDE = ($FFFF shl 16); Source Stride (2D Mode) (Signed (2 s complement) byte increment to apply to the source address at the end of each row in 2D mode)
 
Note: BCM2838_DMA_STRIDE_S_STRIDE and BCM2838_DMA_STRIDE_D_STRIDE not available on DMA Lite channels


BCM2838 DMA debug BCM2838_DMA_DEBUG_*
See: Section 4
 
BCM2838_DMA_DEBUG_READ_LAST_NOT_SET_ERROR = (1 shl 0); Read Last Not Set Error
BCM2838_DMA_DEBUG_FIFO_ERROR = (1 shl 1); Fifo Error
BCM2838_DMA_DEBUG_READ_ERROR = (1 shl 2); Slave Read Response Error
Bit 3 Reserved - Write as 0, read as don't care
BCM2838_DMA_DEBUG_OUTSTANDING_WRITES = ($F shl 4); DMA Outstanding Writes Counter
BCM2838_DMA_DEBUG_DMA_ID = ($FF shl 8); DMA ID
BCM2838_DMA_DEBUG_DMA_STATE = ($1FF shl 16); DMA State Machine State
BCM2838_DMA_DEBUG_VERSION = (7 shl 25); DMA Version
BCM2838_DMA_DEBUG_LITE = (1 shl 28); DMA Lite
Bits 29:31 Reserved - Write as 0, read as don't care


BCM2838 DMA4 control/status BCM2838_DMA4_CS_*
See: Section 4
 
BCM2838_DMA4_CS_ACTIVE = (1 shl 0); Activate the DMA4 (This bit enables the DMA4 to start transferring data)
BCM2838_DMA4_CS_END = (1 shl 1); End Flag (Set when the transfer described by the current Control Block is complete)
BCM2838_DMA4_CS_INT = (1 shl 2); Interrupt Status (If interrupts are enabled (INTEN is set to 1) the interrupt is set when the transfer for the current CB is completed)
BCM2838_DMA4_CS_DREQ = (1 shl 3); DREQ State (Indicates the state of the selected DREQ (Data Request) signal)
BCM2838_DMA4_CS_RD_PAUSED = (1 shl 4); DMA read Paused State (Indicates that the DMA4 is currently paused and not reading data)
BCM2838_DMA4_CS_WR_PAUSED = (1 shl 5); DMA Write Paused State (Indicates that the DMA4 is currently paused and not writing data)
BCM2838_DMA4_CS_DREQ_STOPS_DMA = (1 shl 6); DMA Paused by DREQ State (This indicates that the DMA4 is currently paused and not transferring data due to the selected DREQ being inactive)
BCM2838_DMA4_CS_WAITING_FOR_OUTSTANDING_WRITES = (1 shl 7); The DMA4 is Waiting for all the Write Response to be returned
Bits 8:9 Reserved
BCM2838_DMA4_CS_ERROR = (1 shl 10); DMA Error (Indicates if the DMA4 has detected an error)
Bits 11:15 Reserved
BCM2838_DMA4_CS_QOS_MASK = ($F shl 16); AXI QOS Level (Sets the QOS level of normal AXI bus transactions)
BCM2838_DMA4_CS_QOS_DEFAULT = (0 shl 16);  
BCM2838_DMA4_CS_PANIC_QOS_MASK = ($F shl 20); AXI Panic QOS Level (Sets the QOS level of AXI bus transactions when the DMA4 is panicking)
BCM2838_DMA4_CS_PANIC_QOS_DEFAULT = (0 shl 20);  
BCM2838_DMA4_CS_DMA_BUSY = (1 shl 24); Indicates the DMA4 is BUSY (This indicates that the DMA4 is operating or waiting for outstanding data or otherwise in use)
BCM2838_DMA4_CS_OUTSTANDING_TRANSACTIONS = (1 shl 25); Indicates that there are outstanding AXI transfers, either outstanding read data or outstanding write responses.
Bits 26:27 Reserved
BCM2838_DMA4_CS_WAIT_FOR_OUTSTANDING_WRITES = (1 shl 28); Wait for outstanding writes (The DMA4 keeps a tally of the AXI writes requests going out and the write responses coming in)
BCM2838_DMA4_CS_DISDEBUG = (1 shl 29); Disable Debug Pause Signal (When set to 1, the DMA4 will not pause when the debug pause signal is asserted.)
BCM2838_DMA4_CS_ABORT = (1 shl 30); Abort DMA (Writing a 1 to this bit will cleanly abort the current DMA transfer. The abort will cause the DMA4 to zero its length counters and thus it will complete the current transfer and wait until all outstanding bus activity has finished)
BCM2838_DMA4_CS_HALT = (1 shl 31); Halt DMA (Writing a 1 to this bit will cleanly halt the current DMA transfer. The halt will cause the DMA4 to zero its length counters and thus it will complete the current transfer and wait until all outstanding bus activity has finished.)


BCM2838 DMA4 control block address BCM2838_DMA4_CB_*
See: Section 4
 
BCM2838_DMA4_CB_ADDR_MASK = $0000001FFFFFFFE0;  
BCM2838_DMA4_CB_ADDR_SHIFT = 5; Write Address shr 5 to the register


BCM2838 DMA4 debug register BCM2838_DMA4_DEBUG_*
See: Section 4
 
BCM2838_DMA4_DEBUG_WRITE_ERROR = (1 shl 0); Slave Write Response Error
BCM2838_DMA4_DEBUG_FIFO_ERROR = (1 shl 1); FIFO Error
BCM2838_DMA4_DEBUG_READ_ERROR = (1 shl 2); Slave Read Response Error
BCM2838_DMA4_DEBUG_READ_CB_ERROR = (1 shl 3); Slave Read Response Error During Control Block Read
Bits 4:7 Reserved
BCM2838_DMA4_DEBUG_INT_ON_ERROR = (1 shl 8); Generate an interrupt if an error is detected
BCM2838_DMA4_DEBUG_HALT_ON_ERROR = (1 shl 9); Instruct the DMA4 to HALT if it detects an error
BCM2838_DMA4_DEBUG_ABORT_ON_ERROR = (1 shl 10); Instruct the DMA4 to ABORT if it detects an error
BCM2838_DMA4_DEBUG_DISABLE_CLK_GATE = (1 shl 11); Disable the clock gating logic
Bits 12:13 Reserved
BCM2838_DMA4_DEBUG_R_STATE_MASK = ($F shl 14); Read State Machine State (Returns the value of the DMA4 engine’s read state machine)
BCM2838_DMA4_DEBUG_R_IDLE = (0 shl 14);  
BCM2838_DMA4_DEBUG_R_WAIT_CB_DATA = (1 shl 14);  
BCM2838_DMA4_DEBUG_R_CALC = (2 shl 14);  
BCM2838_DMA4_DEBUG_R_READ4K = (3 shl 14);  
BCM2838_DMA4_DEBUG_R_READING = (4 shl 14);  
BCM2838_DMA4_DEBUG_R_READFIFO_FULL = (5 shl 14);  
BCM2838_DMA4_DEBUG_R_WAIT_WRITE_COMPLETE = (6 shl 14);  
BCM2838_DMA4_DEBUG_W_STATE_MASK = ($F shl 18); Write State Machine State (Returns the value of the DMA4 engine’s write state machine)
BCM2838_DMA4_DEBUG_W_IDLE = (0 shl 18);  
BCM2838_DMA4_DEBUG_W_PRELOAD = (1 shl 18);  
BCM2838_DMA4_DEBUG_W_CALC = (2 shl 18);  
BCM2838_DMA4_DEBUG_W_WRITE4K = (3 shl 18);  
BCM2838_DMA4_DEBUG_W_READFIFO_EMPTY = (4 shl 18);  
BCM2838_DMA4_DEBUG_W_WAIT_OUTSTANDING = (5 shl 18);  
Bit 22 Reserved
BCM2838_DMA4_DEBUG_RESET = (1 shl 23); DMA Reset (This is a hard reset of the DMA4 state machine and certain internal registers)
BCM2838_DMA4_DEBUG_ID_MASK = ($F shl 24); ID (Returns the ID of this DMA4. This is also used as the AXI subid.)
BCM2838_DMA4_DEBUG_VERSION_MASK = ($F shl 28); DMA Version (DMA version number, indicating control bit field changes.)


BCM2838 DMA4 transfer information BCM2838_DMA4_TI_*
See: Section 4
 
BCM2838_DMA4_TI_INTEN = (1 shl 0); Interrupt Enable
BCM2838_DMA4_TI_TDMODE = (1 shl 1); 2D Mode (Perform a 2D transfer instead of a normal linear transfer. In 2D mode the DMA4 will interpret the length field as an X and a Y length. It will execute Y+1 transfers each of length X.)
BCM2838_DMA4_TI_WAIT_RESP = (1 shl 2); Wait for a Write Response (When set this makes the DMA4 wait until it receives the AXI write response for each write)
BCM2838_DMA4_TI_WAIT_RD_RESP = (1 shl 3); Wait for a Read Response (When set this makes the DMA4 wait until it receives all the data from each read)
Bits 4:8 Reserved
BCM2838_DMA4_TI_PERMAP_MASK = ($1F shl 9); Peripheral Mapping (Indicates the DREQ of selected peripheral (1-31))
BCM2838_DMA4_TI_PERMAP_SHIFT = 9;  
BCM2838_DMA4_TI_S_DREQ = (1 shl 14); Control Source Reads with DREQ (This is used when reading from a peripheral that has a DREQ flow control available)
BCM2838_DMA4_TI_D_DREQ = (1 shl 15); Control Destination Writes with DREQ (This is used when writing to a peripheral that has a DREQ flow control available to control the data flow)
BCM2838_DMA4_TI_S_WAITS_MASK = ($FF shl 16); Read Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles burnt before each DMA AXI read operation is started)
BCM2838_DMA4_TI_S_WAITS_DEFAULT = (0 shl 16);  
BCM2838_DMA4_TI_D_WAITS_MASK = ($FF shl 24); Write Wait Cycles (This slows down the DMA throughput by setting the number of dummy cycles before each AXI Write operation is started)
BCM2838_DMA4_TI_D_WAITS_DEFAULT = (0 shl 24);  


BCM2838 DMA4 source address BCM2838_DMA4_SRC_ADDR_*
See: Section 4
 
BCM2838_DMA4_SRC_ADDR_MASK = $00000000FFFFFFFF;  


BCM2838 DMA4 source information BCM2838_DMA4_SRCI_*
See: Section 4
 
BCM2838_DMA4_SRCI_ADDR_MASK = ($FF shl 0); High Bits of the Source Address [40:32]
BCM2838_DMA4_SRCI_BURST_LENGTH_MASK = ($F shl 8); Burst Transfer Length
BCM2838_DMA4_SRCI_BURST_LENGTH_SHIFT = 8;  
BCM2838_DMA4_SRCI_BURST_LENGTH_DEFAULT = (0 shl 8);  
BCM2838_DMA4_SRCI_INC = (1 shl 12); Increment the Source Address
BCM2838_DMA4_SRCI_SIZE_MASK = (3 shl 13); Source Transfer Width (The DMA4 will perform all AXI source reads with this AXI transfer width)
BCM2838_DMA4_SRCI_SIZE_256 = (3 shl 13); Note: On the BCM2711 the width cannot be set larger than 128
BCM2838_DMA4_SRCI_SIZE_128 = (2 shl 13);  
BCM2838_DMA4_SRCI_SIZE_64 = (1 shl 13);  
BCM2838_DMA4_SRCI_SIZE_32 = (0 shl 13);  
BCM2838_DMA4_SRCI_IGNORE = (1 shl 15); Ignore Reads (The DMA4 will perform a normal transfer except that it will not produce any reads. The DMA4 will write zero data.)
BCM2838_DMA4_SRCI_STRIDE = ($FFFF shl 16); Source Stride (This is only used in 2D transfer mode (TDMODE))


BCM2838 DMA4 dest address BCM2838_DMA4_DEST_ADDR_*
See: Section 4
 
BCM2838_DMA4_DEST_ADDR_MASK = $00000000FFFFFFFF;  


BCM2838 DMA4 dest information BCM2838_DMA4_DESTI_*
See: Section 4
 
BCM2838_DMA4_DESTI_ADDR_MASK = ($FF shl 0); High Bits of the Destination Address [40:32]
BCM2838_DMA4_DESTI_BURST_LENGTH_MASK = ($F shl 8); Burst Transfer Length
BCM2838_DMA4_DESTI_BURST_LENGTH_SHIFT = 8;  
BCM2838_DMA4_DESTI_BURST_LENGTH_DEFAULT = (0 shl 8);  
BCM2838_DMA4_DESTI_INC = (1 shl 12); Destination Address Increment
BCM2838_DMA4_DESTI_SIZE_MASK = (3 shl 13); Destination Transfer Width (The DMA4 will perform all AXI destination writes with this AXI transfer width)
BCM2838_DMA4_DESTI_SIZE_256 = (3 shl 13); Note: On the BCM2711 the width cannot be set larger than 128
BCM2838_DMA4_DESTI_SIZE_128 = (2 shl 13);  
BCM2838_DMA4_DESTI_SIZE_64 = (1 shl 13);  
BCM2838_DMA4_DESTI_SIZE_32 = (0 shl 13);  
BCM2838_DMA4_DESTI_IGNORE = (1 shl 15); Ignore Destination Writes
BCM2838_DMA4_DESTI_STRIDE = ($FFFF shl 16); Destination Stride (This is only used in 2D transfer mode (TDMODE))


BCM2838 DMA4 transfer length BCM2838_DMA4_LEN_*
See: Section 4
 
BCM2838_DMA4_LEN_XLENGTH_MASK = ($FFFF shl 0); Transfer Length in bytes
BCM2838_DMA4_LEN_YLENGTH_MASK = ($3FFF shl 16); When in 2D mode, This is the Y transfer length, indicating how many xlength transfers are performed. When in normal linear mode this becomes the top bits of the XLENGTH.
Bits 30:31 Reserved


BCM2838 DMA4 next control block address BCM2838_DMA4_NEXT_CB_ *
See: Section 4
 
BCM2838_DMA4_NEXT_CB_ADDR_MASK = $0000001FFFFFFFE0;  
BCM2838_DMA4_NEXT_CB_ADDR_SHIFT = 5; Write Address shr 5 to the register


BCM2838 DMA4 Debug BCM2838_DMA4_DEBUG2_*
See: Section 4
 
BCM2838_DMA4_DEBUG2_OUTSTANDING_WRITES_MASK = ($1FF shl 0); Outstanding Write Response Count
Bits 9:15 Reserved
BCM2838_DMA4_DEBUG2_OUTSTANDING_READS_MASK = ($1FF shl 16); Outstanding read Words Count
Bits 25:31 Reserved


BCM2838 DMA engine interrupt status BCM2838_DMA_INT_*
See: Section 4
 
BCM2838_DMA_INT_STATUS_0 = (1 shl 0);  
BCM2838_DMA_INT_STATUS_1 = (1 shl 1);  
BCM2838_DMA_INT_STATUS_2 = (1 shl 2);  
BCM2838_DMA_INT_STATUS_3 = (1 shl 3);  
BCM2838_DMA_INT_STATUS_4 = (1 shl 4);  
BCM2838_DMA_INT_STATUS_5 = (1 shl 5);  
BCM2838_DMA_INT_STATUS_6 = (1 shl 6);  
BCM2838_DMA_INT_STATUS_7 = (1 shl 7);  
BCM2838_DMA_INT_STATUS_8 = (1 shl 8);  
BCM2838_DMA_INT_STATUS_9 = (1 shl 9);  
BCM2838_DMA_INT_STATUS_10 = (1 shl 10);  
BCM2838_DMA_INT_STATUS_11 = (1 shl 11);  
BCM2838_DMA_INT_STATUS_12 = (1 shl 12);  
BCM2838_DMA_INT_STATUS_13 = (1 shl 13);  
BCM2838_DMA_INT_STATUS_14 = (1 shl 14);  
BCM2838_DMA_INT_STATUS_15 = (1 shl 15);  
Bits 16:31 Reserved


BCM2838 DMA engine enable BCM2838_DMA_ENABLE_*
See: Section 4
 
BCM2838_DMA_ENABLE_0 = (1 shl 0);  
BCM2838_DMA_ENABLE_1 = (1 shl 1);  
BCM2838_DMA_ENABLE_2 = (1 shl 2);  
BCM2838_DMA_ENABLE_3 = (1 shl 3);  
BCM2838_DMA_ENABLE_4 = (1 shl 4);  
BCM2838_DMA_ENABLE_5 = (1 shl 5);  
BCM2838_DMA_ENABLE_6 = (1 shl 6);  
BCM2838_DMA_ENABLE_7 = (1 shl 7);  
BCM2838_DMA_ENABLE_8 = (1 shl 8);  
BCM2838_DMA_ENABLE_9 = (1 shl 9);  
BCM2838_DMA_ENABLE_10 = (1 shl 10);  
BCM2838_DMA_ENABLE_11 = (1 shl 11);  
BCM2838_DMA_ENABLE_12 = (1 shl 12);  
BCM2838_DMA_ENABLE_13 = (1 shl 13);  
BCM2838_DMA_ENABLE_14 = (1 shl 14);  
Bits 15:23 Reserved
BCM2838_DMA_PAGE_MASK = ($F shl 24); Set the 1G SDRAM ram page that the 30-bit DMA engines (DMA0-6) will access when addressing the 1G uncached range C000_0000->ffff_ffff
BCM2838_DMA_PAGE_DEFAULT = (0 shl 24); addr[29:0] )
BCM2838_DMA_PAGELITE_MASK = ($F shl 28); Set the 1G SDRAM ram page that the DMA Lite engines (DMA7-10) will access when addressing the 1G uncached range C000_0000->ffff_ffff
BCM2838_DMA_PAGELITE_DEFAULT = (0 shl 28); addr[29:0] )


BCM2838 DMA engine DREQ peripheral BCM2838_DMA_DREQ_*
See: Section 4
 
BCM2838_DMA_DREQ_NONE = 0;  
BCM2838_DMA_DREQ_DSI0 = 1;  
BCM2838_DMA_DREQ_PWM1 = 1; The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
BCM2838_DMA_DREQ_PCMTX = 2;  
BCM2838_DMA_DREQ_PCMRX = 3;  
BCM2838_DMA_DREQ_SMI = 4;  
BCM2838_DMA_DREQ_PWM0 = 5;  
BCM2838_DMA_DREQ_SPI0TX = 6;  
BCM2838_DMA_DREQ_SPI0RX = 7;  
BCM2838_DMA_DREQ_BSCSPITX = 8; BSC/SPI Slave
BCM2838_DMA_DREQ_BSCSPIRX = 9; BSC/SPI Slave
BCM2838_DMA_DREQ_HDMI0 = 10;  
BCM2838_DMA_DREQ_EMMC0 = 11; SDHCI
BCM2838_DMA_DREQ_UART0TX = 12;  
BCM2838_DMA_DREQ_EMMC1 = 13; SDHOST
BCM2838_DMA_DREQ_UART0RX = 14;  
BCM2838_DMA_DREQ_DSI1 = 15;  
BCM2838_DMA_DREQ_SPI1TX = 16;  
BCM2838_DMA_DREQ_HDMI1 = 17;  
BCM2838_DMA_DREQ_SPI1RX = 18;  
BCM2838_DMA_DREQ_UART3TX = 19;  
BCM2838_DMA_DREQ_SPI4TX = 19; The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
BCM2838_DMA_DREQ_UART3RX = 20;  
BCM2838_DMA_DREQ_SPI4RX = 20; The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
BCM2838_DMA_DREQ_UART5TX = 21;  
BCM2838_DMA_DREQ_SPI5TX = 21; The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
BCM2838_DMA_DREQ_UART5RX = 22;  
BCM2838_DMA_DREQ_SPI5RX = 22; The alternate DREQs are available by changing the DMA_CNTRL_MUX bits in the PACTL_CS register
BCM2838_DMA_DREQ_SPI6TX = 23;  
BCM2838_DMA_DREQ_SCALER_FIFO0 = 24; Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
BCM2838_DMA_DREQ_SCALER_FIFO1 = 25; Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
BCM2838_DMA_DREQ_SCALER_FIFO2 = 26; Scaler FIFO 0 & SMI (The SMI element can be disabled by setting the SMI_DISABLE bit in the DMA_DREQ_CONTROL register)
BCM2838_DMA_DREQ_SPI6RX = 27;  
BCM2838_DMA_DREQ_UART2TX = 28;  
BCM2838_DMA_DREQ_UART2RX = 29;  
BCM2838_DMA_DREQ_UART4TX = 30;  
BCM2838_DMA_DREQ_UART4RX = 31;  


BCM2838 BSC (I2C0/1/2) control BCM2838_BSC_C_*
See: Section 3.2
 
BCM2838_BSC_C_I2CEN = (1 shl 15); I2C Enable (0 = BSC controller is disabled / 1 = BSC controller is enabled)
BCM2838_BSC_C_INTR = (1 shl 10); INTR Interrupt on RX (0 = Don t generate interrupts on RXR condition / 1 = Generate interrupt while RXR = 1)
BCM2838_BSC_C_INTT = (1 shl 9); INTT Interrupt on TX (0 = Don t generate interrupts on TXW condition / 1 = Generate interrupt while TXW = 1)
BCM2838_BSC_C_INTD = (1 shl 8); INTD Interrupt on DONE (0 = Don t generate interrupts on DONE condition / 1 = Generate interrupt while DONE = 1)
BCM2838_BSC_C_ST = (1 shl 7); ST Start Transfer (0 = No action / 1 = Start a new transfer. One shot operation. Read back as 0)
BCM2838_BSC_C_CLEAR = (1 shl 5); CLEAR FIFO Clear (00 = No action / x1 = Clear FIFO. One shot operation / 1x = Clear FIFO. One shot operation)
BCM2838_BSC_C_READ = (1 shl 0); READ Read Transfer (0 = Write Packet Transfer / 1 = Read Packet Transfer)


BCM2838 BSC (I2C0/1/2) status BCM2838_BSC_S_*
See: Section 3.2
 
BCM2838_BSC_S_CLKT = (1 shl 9); CLKT Clock Stretch Timeout (0 = No errors detected. 1 = Slave has held the SCL signal low (clock stretching) for longer and that specified in the I2CCLKT register Cleared by writing 1 to the field.)
BCM2838_BSC_S_ERR = (1 shl 8); ERR ACK Error (0 = No errors detected. 1 = Slave has not acknowledged its address. Cleared by writing 1 to the field.)
BCM2838_BSC_S_RXF = (1 shl 7); RXF - FIFO Full (0 = FIFO is not full. 1 = FIFO is full. If a read is underway, no further serial data will be received until data is read from FIFO.)
BCM2838_BSC_S_TXE = (1 shl 6); TXE - FIFO Empty (0 = FIFO is not empty. 1 = FIFO is empty. If a write is underway, no further serial data can be transmitted until data is written to the FIFO.)
BCM2838_BSC_S_RXD = (1 shl 5); RXD - FIFO contains Data (0 = FIFO is empty. 1 = FIFO contains at least 1 byte. Cleared by reading sufficient data from FIFO.)
BCM2838_BSC_S_TXD = (1 shl 4); TXD - FIFO can accept Data (0 = FIFO is full. The FIFO cannot accept more data. 1 = FIFO has space for at least 1 byte.)
BCM2838_BSC_S_RXR = (1 shl 3); RXR - FIFO needs Reading (full) (0 = FIFO is less than full and a read is underway. 1 = FIFO is or more full and a read is underway. Cleared by reading sufficient data from the FIFO.)
BCM2838_BSC_S_TXW = (1 shl 2); TXW - FIFO needs Writing (full) (0 = FIFO is at least full and a write is underway (or sufficient data to send). 1 = FIFO is less then full and a write is underway. Cleared by writing sufficient data to the FIFO.)
BCM2838_BSC_S_DONE = (1 shl 1); DONE Transfer Done (0 = Transfer not completed. 1 = Transfer complete. Cleared by writing 1 to the field.)
BCM2838_BSC_S_TA = (1 shl 0); TA Transfer Active (0 = Transfer not active. 1 = Transfer active.)


BCM2838 BSC (I2C0/1/2) data length BCM2838_BSC_DLEN_*
See: Section 3.2
 
BCM2838_BSC_DLEN_MASK = $FFFF; Data Length. (Writing to DLEN specifies the number of bytes to be transmitted/received. Reading from DLEN when TA = 1 or DONE = 1, returns the number of bytes still to be transmitted or received.)


BCM2838 BSC (I2C0/1/2) slave address BCM2838_BSC_A_*
See: Section 3.2
 
BCM2838_BSC_A_MASK = $7F; Slave Address


BCM2838 BSC (I2C0/1/2) data FIFO BCM2838_BSC_FIFO_*
See: Section 3.2
 
BCM2838_BSC_FIFO_MASK = $FF; Writes to the register write transmit data to the FIFO. Reads from register reads received data from the FIFO.
BCM2838_BSC_FIFO_SIZE = 16;  


BCM2838 BSC (I2C0/1/2) clock divider BCM2838_BSC_CDIV_*
See: Section 3.2
 
BCM2838_BSC_CDIV_MASK = $FFFF; Clock Divider (SCL = core clock / CDIV) (CDIV is always rounded down to an even number)


BCM2838 BSC (I2C0/1/2) data delay BCM2838_BSC_DEL_*
See: Section 3.2
 
BCM2838_BSC_DEL_FEDL_MASK = ($FFFF shl 16); FEDL Falling Edge Delay (Number of core clock cycles to wait after the falling edge of SCL before outputting next bit of data)
BCM2838_BSC_DEL_REDL_MASK = ($FFFF shl 0); REDL Rising Edge Delay (Number of core clock cycles to wait after the rising edge of SCL before reading the next bit of data)


BCM2838 BSC (I2C0/1/2) clock stretch timeout BCM2838_BSC_CLKT_TOUT_*
See: Section 3.2
 
BCM2838_BSC_CLKT_TOUT_MASK = $FFFF; TOUT Clock Stretch Timeout Value (Number of SCL clock cycles to wait after the rising edge of SCL before deciding that the slave is not responding)


BCM2838 SPI0 BCM2838_SPI0_*
See: Section 10.5
 
BCM2838_SPI0_CS_LEN_LONG = (1 shl 25); Enable Long data word in Lossi mode if DMA_LEN is set (0 = writing to the FIFO will write a single byte / 1 = writing to the FIFO will write a 32 bit word)
BCM2838_SPI0_CS_DMA_LEN = (1 shl 24); Enable DMA mode in Lossi mode
BCM2838_SPI0_CS_CSPOL2 = (1 shl 23); Chip Select 2 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
BCM2838_SPI0_CS_CSPOL1 = (1 shl 22); Chip Select 1 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
BCM2838_SPI0_CS_CSPOL0 = (1 shl 21); Chip Select 0 Polarity (0 = Chip select is active low / 1 = Chip select is active high)
BCM2838_SPI0_CS_RXF = (1 shl 20); RXF - RX FIFO Full (0 = RXFIFO is not full / 1 = RX FIFO is full. No further serial data will be sent/received until data is read from FIFO.)
BCM2838_SPI0_CS_RXR = (1 shl 19); RXR RX FIFO needs Reading (full) (0 = RX FIFO is less than full (or not active TA = 0) / 1 = RX FIFO is or more full. Cleared by reading sufficient data from the RX FIFO or setting TA to 0.)
BCM2838_SPI0_CS_TXD = (1 shl 18); TXD TX FIFO can accept Data (0 = TX FIFO is full and so cannot accept more data / 1 = TX FIFO has space for at least 1 byte)
BCM2838_SPI0_CS_RXD = (1 shl 17); RXD RX FIFO contains Data (0 = RX FIFO is empty / 1 = RX FIFO contains at least 1 byte)
BCM2838_SPI0_CS_DONE = (1 shl 16); DONE Transfer Done (0 = Transfer is in progress (or not active TA = 0) / 1 = Transfer is complete. Cleared by writing more data to the TX FIFO or setting TA to 0.)
BCM2838_SPI0_CS_TE_EN = (1 shl 15); Unused
BCM2838_SPI0_CS_LMONO = (1 shl 14); Unused
BCM2838_SPI0_CS_LEN = (1 shl 13); LEN LoSSI enable (0 = The serial interface will behave as an SPI master / 1 = The serial interface will behave as a LoSSI master)
BCM2838_SPI0_CS_REN = (1 shl 12); REN Read Enable. If this bit is set, the SPI peripheral will be able to send data to this device (0 = We intend to write to the SPI peripheral / 1 = We intend to read from the SPI peripheral)
BCM2838_SPI0_CS_ADCS = (1 shl 11); ADCS Automatically Deassert Chip Select (0 = Don t automatically deassert chip select at the end of a DMA transfer chip select is manually controlled by software / 1 = Automatically deassert chip select at the end of a DMA transfer as determined by SPIDLEN)
BCM2838_SPI0_CS_INTR = (1 shl 10); INTR Interrupt on RXR (0 = Don t generate interrupts on RX FIFO condition / 1 = Generate interrupt while RXR = 1)
BCM2838_SPI0_CS_INTD = (1 shl 9); INTD Interrupt on Done (0 = Don t generate interrupt on transfer complete / 1 = Generate interrupt when DONE = 1)
BCM2838_SPI0_CS_DMAEN = (1 shl 8); DMAEN DMA Enable (0 = No DMA requests will be issued / 1 = Enable DMA operation. Peripheral generates data requests. These will be taken in four-byte words until the SPIDLEN has been reached.
BCM2838_SPI0_CS_TA = (1 shl 7); Transfer Active (0 = Transfer not active / 1 = Transfer active)
BCM2838_SPI0_CS_CSPOL = (1 shl 6); Chip Select Polarity (0 = Chip select lines are active low / 1 = Chip select lines are active high
BCM2838_SPI0_CS_CLEAR_RX = (1 shl 5); CLEAR FIFO Clear (00 = No action / x1 = Clear TX FIFO. One shot operation / 1x = Clear RX FIFO. One shot operation.)
BCM2838_SPI0_CS_CLEAR_TX = (1 shl 4); As above
BCM2838_SPI0_CS_CPOL = (1 shl 3); Clock Polarity (0 = Rest state of clock = low / 1 = Rest state of clock = high)
BCM2838_SPI0_CS_CPHA = (1 shl 2); Clock Phase (0 = First SCLK transition at middle of data bit / 1 = First SCLK transition at beginning of data bit)
BCM2838_SPI0_CS_CS_0 = (0 shl 0); Chip Select (00 = Chip select 0 / 01 = Chip select 1 / 10 = Chip select 2 / 11 = Reserved
BCM2838_SPI0_CS_CS_1 = (1 shl 0); As above
BCM2838_SPI0_CS_CS_2 = (2 shl 0); As above
 
BCM2838_SPI0_CS_CS_MASK = (3 shl 0);  
 
BCM2838_SPI0_FIFO_DMA_DATA = $FFFFFFFF; DMA Mode (DMAEN set) If TA is clear, the first 32-bit write to this register will control SPIDLEN and SPICS. Subsequent reads and writes will be taken as four-byte data words to be read/written to the FIFOs.
BCM2838_SPI0_FIFO_IRQ_DATA = $000000FF; Poll/Interrupt Mode (DMAEN clear, TA set) Writes to the register write bytes to TX FIFO. Reads from register read bytes from the RX FIFO.
 
BCM2838_SPI0_CLK_CDIV = $0000FFFF; Clock Divider (SCLK = Core Clock / CDIV) If CDIV is set to 0, the divisor is 65536. The divisor must be a multiple of 2. Odd numbers rounded down. The maximum SPI clock rate is of the APB clock.
 
BCM2838_SPI0_DLEN_LEN = $0000FFFF; Data Length. The number of bytes to transfer. This field is only valid for DMA mode (DMAEN set) and controls how many bytes to transmit (and therefore receive).
 
BCM2838_SPI0_LTOH_TOH = $0000000F; This sets the Output Hold delay in APB clocks (A value of 0 causes a 1 clock delay)
 
BCM2838_SPI0_DC_RPANIC = ($FF shl 24); DMA Read Panic Threshold (Generate the Panic signal to the RX DMA engine whenever the RX FIFO level is greater than this amount)
BCM2838_SPI0_DC_RDREQ = ($FF shl 16); DMA Read Request Threshold (Generate A DREQ to the RX DMA engine whenever the RX FIFO level is greater than this amount) (RX DREQ is also generated if thetransfer has finished but the RXFIFO isn't empty)
BCM2838_SPI0_DC_TPANIC = ($FF shl 8); DMA Write Panic Threshold (Generate the Panic signal to the TX DMA engine whenever the TX FIFO level is less than or equal to this amount)
BCM2838_SPI0_DC_TDREQ = ($FF shl 0); DMA Write Request Threshold (Generate a DREQ signal to the TX DMA engine whenever the TX FIFO level is less than or equal to this amount)


BCM2838 I2C/SPI Slave register
See: Section 11.2
 


BCM2838 AUX (UART1, SPI1 and SPI2) register
See: Section 2.1
 


BCM2838 PCM/I2S register
See: Section 8.8
 


BCM2838 PWM control BCM2838_PWM_CTL_*
See: Section 9.6
 
BCM2838_PWM_CTL_MSEN2 = (1 shl 15); Channel 2 M/S Enable (0: PWM algorithm is used / 1: M/S transmission is used)
Bit 14 Reserved - Write as 0, read as don't care
BCM2838_PWM_CTL_USEF2 = (1 shl 13); Channel 2 Use Fifo (0: Data register is transmitted / 1: Fifo is used for transmission)
BCM2838_PWM_CTL_POLA2 = (1 shl 12); Channel 2 Polarity (0 : 0=low 1=high / 1: 1=low 0=high)
BCM2838_PWM_CTL_SBIT2 = (1 shl 11); Channel 2 Silence Bit (Defines the state of the output when no transmission takes place)
BCM2838_PWM_CTL_RPTL2 = (1 shl 10); Channel 2 Repeat Last Data (0: Transmission interrupts when FIFO is empty / 1: Last data in FIFO is transmitted repeatedly until FIFO is not empty)
BCM2838_PWM_CTL_MODE2 = (1 shl 9); Channel 2 Mode (0: PWM mode / 1: Serialiser mode)
BCM2838_PWM_CTL_PWEN2 = (1 shl 8); Channel 2 Enable (0: Channel is disabled / 1: Channel is enabled)
BCM2838_PWM_CTL_MSEN1 = (1 shl 7); Channel 1 M/S Enable (0: PWM algorithm is used / 1: M/S transmission is used)
BCM2838_PWM_CTL_CLRF1 = (1 shl 6); Clear Fifo (1: Clears FIFO / 0: Has no effect) (This is a single shot operation. This bit always reads 0.)
BCM2838_PWM_CTL_USEF1 = (1 shl 5); Channel 1 Use Fifo (0: Data register is transmitted / 1: Fifo is used for transmission)
BCM2838_PWM_CTL_POLA1 = (1 shl 4); Channel 1 Polarity (0 : 0=low 1=high / 1: 1=low 0=high)
BCM2838_PWM_CTL_SBIT1 = (1 shl 3); Channel 1 Silence Bit (Defines the state of the output when no transmission takes place)
BCM2838_PWM_CTL_RPTL1 = (1 shl 2); Channel 1 Repeat Last Data (0: Transmission interrupts when FIFO is empty / 1: Last data in FIFO is transmitted repeatedly until FIFO is not empty)
BCM2838_PWM_CTL_MODE1 = (1 shl 1); Channel 1 Mode (0: PWM mode / 1: Serialiser mode)
BCM2838_PWM_CTL_PWEN1 = (1 shl 0); Channel 1 Enable (0: Channel is disabled / 1: Channel is enabled)


BCM2838 PWM status BCM2838_PWM_STA_*
See: Section 9.6
 
BCM2838_PWM_STA_STA4 = (1 shl 12); Channel 4 State
BCM2838_PWM_STA_STA3 = (1 shl 11); Channel 3 State
BCM2838_PWM_STA_STA2 = (1 shl 10); Channel 2 State
BCM2838_PWM_STA_STA1 = (1 shl 9); Channel 1 State
BCM2838_PWM_STA_BERR = (1 shl 8); Bus Error Flag
BCM2838_PWM_STA_GAPO4 = (1 shl 7); Channel 4 Gap Occurred Flag
BCM2838_PWM_STA_GAPO3 = (1 shl 6); Channel 3 Gap Occurred Flag
BCM2838_PWM_STA_GAPO2 = (1 shl 5); Channel 2 Gap Occurred Flag
BCM2838_PWM_STA_GAPO1 = (1 shl 4); Channel 1 Gap Occurred Flag
BCM2838_PWM_STA_RERR1 = (1 shl 3); Fifo Read Error Flag
BCM2838_PWM_STA_WERR1 = (1 shl 2); Fifo Write Error Flag
BCM2838_PWM_STA_EMPT1 = (1 shl 1); Fifo Empty Flag
BCM2838_PWM_STA_FULL1 = (1 shl 0); Fifo Full Flag


BCM2838 PWM DMA configuration BCM2838_PWM_DMAC_*
See: Section 9.6
 
BCM2838_PWM_DMAC_ENAB = (1 shl 31); DMA Enable (0: DMA disabled / 1: DMA enabled)
BCM2838_PWM_DMAC_PANIC = ($FF shl 8); DMA Threshold for PANIC signal (Default: 0x7)
BCM2838_PWM_DMAC_DREQ = ($FF shl 0); DMA Threshold for DREQ signal (Default: 0x7)


BCM2838 Pulse Width Modulator (PWM) BCM2838_PWM_ *
BCM2838_PWM_CTL = $00000000; PWM Control
BCM2838_PWM_STA = $00000004; PWM Status
BCM2838_PWM_DMAC = $00000008; PWM DMA Configuration
BCM2838_PWM_RNG1 = $00000010; PWM Channel 1 Range
BCM2838_PWM_DAT1 = $00000014; PWM Channel 1 Data
BCM2838_PWM_FIF1 = $00000018; PWM FIFO Input
BCM2838_PWM_RNG2 = $00000020; PWM Channel 2 Range
BCM2838_PWM_DAT2 = $00000024; PWM Channel 2 Data


BCM2838 PL011 UART data BCM2838_PL011_*
See: Section 13.4
 
BCM2838_PL011_DR_OE = (1 shl 11); Overrun error
BCM2838_PL011_DR_BE = (1 shl 10); Break error
BCM2838_PL011_DR_PE = (1 shl 9); Parity error
BCM2838_PL011_DR_FE = (1 shl 8); Framing error
BCM2838_PL011_DR_DATA = ($FF shl 0); Receive / Transmit data
BCM2838_PL011_DR_ERROR = BCM2838_PL011_DR_OE or BCM2838_PL011_DR_BE or BCM2838_PL011_DR_PE or BCM2838_PL011_DR_FE;  


BCM2838 PL011 UART receive status/error clear BCM2838_PL011_RSRECR_*
See: Section 13.4
 
BCM2838_PL011_RSRECR_OE = (1 shl 3); Overrun error
BCM2838_PL011_RSRECR_BE = (1 shl 2); Break error
BCM2838_PL011_RSRECR_PE = (1 shl 1); Parity error
BCM2838_PL011_RSRECR_FE = (1 shl 0); Framing error


BCM2838 PL011 UART flag BCM2838_PL011_FR_*
See: Section 13.4
 
BCM2838_PL011_FR_RI = (1 shl 8); Unsupported, write zero, read as don't care
BCM2838_PL011_FR_TXFE = (1 shl 7); Transmit FIFO empty
BCM2838_PL011_FR_RXFF = (1 shl 6); Receive FIFO full
BCM2838_PL011_FR_TXFF = (1 shl 5); Transmit FIFO full
BCM2838_PL011_FR_RXFE = (1 shl 4); Receive FIFO empty
BCM2838_PL011_FR_BUSY = (1 shl 3); UART busy
BCM2838_PL011_FR_DCD = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_FR_DSR = (1 shl 1); Unsupported, write zero, read as don't care
BCM2838_PL011_FR_CTS = (1 shl 0); Clear to send (This bit is the complement of the UART clear to send, nUARTCTS, modem status input. That is, the bit is 1 when nUARTCTS is LOW.)


BCM2838 PL011 UART IrDA
See: Section 13.4
 
This register is disabled, writing to it has no effect and reading returns 0


BCM2838 PL011 UART integer baud rate divisor BCM2838_PL011_IBRD_*
BCM2838_PL011_IBRD_MASK = ($FFFF shl 0);  


BCM2838 PL011 UART fractional baud rate divisor BCM2838_PL011_FBRD_*
See: Section 13.4
 
BCM2838_PL011_FBRD_MASK = ($3F shl 0);  


BCM2838 PL011 UART line control BCM2838_PL011_LCRH_*
See: Section 13.4
 
BCM2838_PL011_LCRH_SPS = (1 shl 7); Stick parity select
BCM2838_PL011_LCRH_WLEN = (3 shl 5); Word length
BCM2838_PL011_LCRH_WLEN8 = (3 shl 5); 8 bits
BCM2838_PL011_LCRH_WLEN7 = (2 shl 5); 7 bits
BCM2838_PL011_LCRH_WLEN6 = (1 shl 5); 6 bits
BCM2838_PL011_LCRH_WLEN5 = (0 shl 5); 5 bits
BCM2838_PL011_LCRH_FEN = (1 shl 4); Enable FIFOs
BCM2838_PL011_LCRH_STP2 = (1 shl 3); Two stop bits select
BCM2838_PL011_LCRH_EPS = (1 shl 2); Even parity select (0 = odd parity / 1 = even parity)
BCM2838_PL011_LCRH_PEN = (1 shl 1); Parity enable
BCM2838_PL011_LCRH_BRK = (1 shl 0); Send break


BCM2838 PL011 UART control BCM2838_PL011_CR_*
See: Section 13.4
 
BCM2838_PL011_CR_CTSEN = (1 shl 15); CTS hardware flow control enable (If this bit is set to 1 data is only transmitted when the nUARTCTS signal is asserted)
BCM2838_PL011_CR_RTSEN = (1 shl 14); RTS hardware flow control enable (If this bit is set to 1 data is only requested when there is space in the receive FIFO for it to be received)
BCM2838_PL011_CR_OUT2 = (1 shl 13); Unsupported, write zero, read as don't care
BCM2838_PL011_CR_OUT1 = (1 shl 12); Unsupported, write zero, read as don't care
BCM2838_PL011_CR_RTS = (1 shl 11); Request to send (This bit is the complement of the UART request to send, nUARTRTS, modem status output. That is, when the bit is programmed to a 1 then nUARTRTS is LOW.)
BCM2838_PL011_CR_DTR = (1 shl 10); Unsupported, write zero, read as don't care
BCM2838_PL011_CR_RXE = (1 shl 9); Receive enable
BCM2838_PL011_CR_TXE = (1 shl 8); Transmit enable
BCM2838_PL011_CR_LBE = (1 shl 7); Loopback enable
Bits 6:3 Reserved - Write as 0, read as don't care
BCM2838_PL011_CR_SIRLP = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_CR_SIREN = (1 shl 1); Unsupported, write zero, read as don't care
BCM2838_PL011_CR_UARTEN = (1 shl 0); UART enable


BCM2838 PL011 UART interrupt FIFO level select BCM2838_PL011_IFLS_*
See: Section 13.4
 
BCM2838_PL011_IFLS_RXIFPSEL = (7 shl 9); Unsupported, write zero, read as don't care
BCM2838_PL011_IFLS_TXIFPSEL = (7 shl 6); Unsupported, write zero, read as don't care
BCM2838_PL011_IFLS_RXIFLSEL = (7 shl 3); Receive interrupt FIFO level select
BCM2838_PL011_IFLS_RXIFLSEL1_8 = (0 shl 3); b000 = Receive FIFO becomes >= 1/8 full
BCM2838_PL011_IFLS_RXIFLSEL1_4 = (1 shl 3); b001 = Receive FIFO becomes >= 1/4 full
BCM2838_PL011_IFLS_RXIFLSEL1_2 = (2 shl 3); b010 = Receive FIFO becomes >= 1/2 full
BCM2838_PL011_IFLS_RXIFLSEL3_4 = (3 shl 3); b011 = Receive FIFO becomes >= 3/4 full
BCM2838_PL011_IFLS_RXIFLSEL7_8 = (4 shl 3); b100 = Receive FIFO becomes >= 7/8 full
BCM2838_PL011_IFLS_TXIFLSEL = (7 shl 0); Transmit interrupt FIFO level select
BCM2838_PL011_IFLS_TXIFLSEL1_8 = (0 shl 0); b000 = Transmit FIFO becomes <= 1/8 full
BCM2838_PL011_IFLS_TXIFLSEL1_4 = (1 shl 0); b001 = Transmit FIFO becomes <= 1/4 full
BCM2838_PL011_IFLS_TXIFLSEL1_2 = (2 shl 0); b010 = Transmit FIFO becomes <= 1/2 full
BCM2838_PL011_IFLS_TXIFLSEL3_4 = (3 shl 0); b011 = Transmit FIFO becomes <= 3/4 full
BCM2838_PL011_IFLS_TXIFLSEL7_8 = (4 shl 0); b100 = Transmit FIFO becomes <= 7/8 full


BCM2838 PL011 UART interrupt mask set/clear BCM2838_PL011_IMSC_*
See: Section 13.4
 
BCM2838_PL011_IMSC_OEIM = (1 shl 10); Overrun error interrupt mask
BCM2838_PL011_IMSC_BEIM = (1 shl 9); Break error interrupt mask
BCM2838_PL011_IMSC_PEIM = (1 shl 8); Parity error interrupt mask
BCM2838_PL011_IMSC_FEIM = (1 shl 7); Framing error interrupt mask
BCM2838_PL011_IMSC_RTIM = (1 shl 6); Receive timeout interrupt mask
BCM2838_PL011_IMSC_TXIM = (1 shl 5); Transmit interrupt mask
BCM2838_PL011_IMSC_RXIM = (1 shl 4); Receive interrupt mask
BCM2838_PL011_IMSC_DSRMIM = (1 shl 3); Unsupported, write zero, read as don't care
BCM2838_PL011_IMSC_DCDMIM = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_IMSC_CTSMIM = (1 shl 1); nUARTCTS modem interrupt mask
BCM2838_PL011_IMSC_RIMIM = (1 shl 0); Unsupported, write zero, read as don't care


BCM2838 PL011 UART raw interrupt status BCM2838_PL011_RIS_*
See: Section 13.4
 
BCM2838_PL011_RIS_OERIS = (1 shl 10); Overrun error interrupt status
BCM2838_PL011_RIS_BERIS = (1 shl 9); Break error interrupt status
BCM2838_PL011_RIS_PERIS = (1 shl 8); Parity error interrupt status
BCM2838_PL011_RIS_FERIS = (1 shl 7); Framing error interrupt status
BCM2838_PL011_RIS_RTRIS = (1 shl 6); Receive timeout interrupt status
BCM2838_PL011_RIS_TXRIS = (1 shl 5); Transmit interrupt status
BCM2838_PL011_RIS_RXRIS = (1 shl 4); Receive interrupt status
BCM2838_PL011_RIS_DSRMRIS = (1 shl 3); Unsupported, write zero, read as don't care
BCM2838_PL011_RIS_DCDMRIS = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_RIS_CTSMRIS = (1 shl 1); nUARTCTS modem interrupt status
BCM2838_PL011_RIS_RIMRIS = (1 shl 0); Unsupported, write zero, read as don't care


BCM2838 PL011 UART masked interrupt status BCM2838_PL011_MIS_*
See: Section 13.4
 
BCM2838_PL011_MIS_OEMIS = (1 shl 10); Overrun error masked interrupt status
BCM2838_PL011_MIS_BEMIS = (1 shl 9); Break error masked interrupt status
BCM2838_PL011_MIS_PEMIS = (1 shl 8); Parity error masked interrupt status
BCM2838_PL011_MIS_FEMIS = (1 shl 7); Framing error masked interrupt status
BCM2838_PL011_MIS_RTMIS = (1 shl 6); Receive timeout masked interrupt status
BCM2838_PL011_MIS_TXMIS = (1 shl 5); Transmit masked interrupt status
BCM2838_PL011_MIS_RXMIS = (1 shl 4); Receive masked interrupt status
BCM2838_PL011_MIS_DSRMMIS = (1 shl 3); Unsupported, write zero, read as don't care
BCM2838_PL011_MIS_DCDMMIS = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_MIS_CTSMMIS = (1 shl 1); nUARTCTS modem masked interrupt status
BCM2838_PL011_MIS_RIMMIS = (1 shl 0); Unsupported, write zero, read as don't care


BCM2838 PL011 UART interrupt clear BCM2838_PL011_ICR_*
See: Section 13.4
 
BCM2838_PL011_ICR_OEIC = (1 shl 10); Overrun error interrupt clear
BCM2838_PL011_ICR_BEIC = (1 shl 9); Break error interrupt clear
BCM2838_PL011_ICR_PEIC = (1 shl 8); Parity error interrupt clear
BCM2838_PL011_ICR_FEIC = (1 shl 7); Framing error interrupt clear
BCM2838_PL011_ICR_RTIC = (1 shl 6); Receive timeout interrupt clear
BCM2838_PL011_ICR_TXIC = (1 shl 5); Transmit interrupt clear
BCM2838_PL011_ICR_RXIC = (1 shl 4); Receive interrupt clear
BCM2838_PL011_ICR_DSRMIC = (1 shl 3); Unsupported, write zero, read as don't care
BCM2838_PL011_ICR_DCDMIC = (1 shl 2); Unsupported, write zero, read as don't care
BCM2838_PL011_ICR_CTSMIC = (1 shl 1); nUARTCTS modem interrupt clear
BCM2838_PL011_ICR_RIMIC = (1 shl 0); Unsupported, write zero, read as don't care


BCM2838 PL011 UART DMA control
See: Section 13.4
 
This register is disabled, writing to it has no effect and reading returns 0


BCM2838 PL011 UART test control
See: Section 13.4
 


BCM2838 PL011 UART integration test input
See: Section 13.4
 


BCM2838 PL011 UART integration test output
See: Section 13.4
 


BCM2838 PL011 UART test data
See: Section 13.4
 


BCM2838 ARM legacy interrupt controller BCM2838_ARM_INTERRUPT_*
BCM2838_ARM_INTERRUPT_IRQ0_PENDING0 = $00000000; ARM Core 0 IRQ Enabled Interrupt Pending bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ0_PENDING1 = $00000004; ARM Core 0 IRQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ0_PENDING2 = $00000008; ARM Core 0 IRQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_0 = $00000010; Write to Set ARM Core 0 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_1 = $00000014; Write to Set ARM Core 0 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ0_SET_EN_2 = $00000018; Write to Set ARM Core 0 IRQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_0 = $00000020; Write to Clear ARM Core 0 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_1 = $00000024; Write to Clear ARM Core 0 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ0_CLR_EN_2 = $00000028; Write to Clear ARM Core 0 IRQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ_STATUS0 = $00000030; Interrupt Line bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ_STATUS1 = $00000034; Interrupt Line bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ_STATUS2 = $00000038; Interrupt Line bits [79:64]
 
BCM2838_ARM_INTERRUPT_IRQ1_PENDING0 = $00000040; ARM Core 1 IRQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ1_PENDING1 = $00000044; ARM Core 1 IRQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ1_PENDING2 = $00000048; ARM Core 1 IRQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_0 = $00000050; Write to Set ARM Core 1 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_1 = $00000054; Write to Set ARM Core 1 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ1_SET_EN_2 = $00000058; Write to Set ARM Core 1 IRQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_0 = $00000060; Write to Clear ARM Core 1 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_1 = $00000064; Write to Clear ARM Core 1 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ1_CLR_EN_2 = $00000068; Write to Clear ARM Core 1 IRQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_IRQ2_PENDING0 = $00000080; ARM Core 2 IRQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ2_PENDING1 = $00000084; ARM Core 2 IRQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ2_PENDING2 = $00000088; ARM Core 2 IRQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_0 = $00000090; Write to Set ARM Core 2 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_1 = $00000094; Write to Set ARM Core 2 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ2_SET_EN_2 = $00000098; Write to Set ARM Core 2 IRQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_0 = $000000A0; Write to Clear ARM Core 2 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_1 = $000000A4; Write to Clear ARM Core 2 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ2_CLR_EN_2 = $000000A8; Write to Clear ARM Core 2 IRQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_IRQ3_PENDING0 = $000000C0; ARM Core 3 IRQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ3_PENDING1 = $000000C4; ARM Core 3 IRQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ3_PENDING2 = $000000C8; ARM Core 3 IRQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_0 = $000000D0; Write to Set ARM Core 3 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_1 = $000000D4; Write to Set ARM Core 3 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ3_SET_EN_2 = $000000D8; Write to Set ARM Core 3 IRQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_0 = $000000E0; Write to Clear ARM Core 3 IRQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_1 = $000000E4; Write to Clear ARM Core 3 IRQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_IRQ3_CLR_EN_2 = $000000E8; Write to Clear ARM Core 3 IRQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_FIQ0_PENDING0 = $00000100; ARM Core 0 FIQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ0_PENDING1 = $00000104; ARM Core 0 FIQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ0_PENDING2 = $00000108; ARM Core 0 FIQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_0 = $00000110; Write to Set ARM Core 0 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_1 = $00000114; Write to Set ARM Core 0 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ0_SET_EN_2 = $00000118; Write to Set ARM Core 0 FIQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_0 = $00000120; Write to Clear ARM Core 0 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_1 = $00000124; Write to Clear ARM Core 0 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ0_CLR_EN_2 = $00000128; Write to Clear ARM Core 0 FIQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_FIQ1_PENDING0 = $00000140; ARM Core 1 FIQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ1_PENDING1 = $00000144; ARM Core 1 FIQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ1_PENDING2 = $00000148; ARM Core 1 FIQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_0 = $00000150; Write to Set ARM Core 1 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_1 = $00000154; Write to Set ARM Core 1 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ1_SET_EN_2 = $00000158; Write to Set ARM Core 1 FIQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_0 = $00000160; Write to Clear ARM Core 1 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_1 = $00000164; Write to Clear ARM Core 1 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ1_CLR_EN_2 = $00000168; Write to Clear ARM Core 1 FIQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_FIQ2_PENDING0 = $00000180; ARM Core 2 FIQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ2_PENDING1 = $00000184; ARM Core 2 FIQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ2_PENDING2 = $00000188; ARM Core 2 FIQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_0 = $00000190; Write to Set ARM Core 2 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_1 = $00000194; Write to Set ARM Core 2 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ2_SET_EN_2 = $00000198; Write to Set ARM Core 2 FIQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_0 = $000001A0; Write to Clear ARM Core 2 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_1 = $000001A4; Write to Clear ARM Core 2 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ2_CLR_EN_2 = $000001A8; Write to Clear ARM Core 2 FIQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_FIQ3_PENDING0 = $000001C0; ARM Core 3 FIQ Enabled Interrupt pending bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ3_PENDING1 = $000001C4; ARM Core 3 FIQ Enabled Interrupt pending bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ3_PENDING2 = $000001C8; ARM Core 3 FIQ Enabled Interrupt pending bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_0 = $000001D0; Write to Set ARM Core 3 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_1 = $000001D4; Write to Set ARM Core 3 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ3_SET_EN_2 = $000001D8; Write to Set ARM Core 3 FIQ enable bits [79:64]
BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_0 = $000001E0; Write to Clear ARM Core 3 FIQ enable bits [31:0]
BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_1 = $000001E4; Write to Clear ARM Core 3 FIQ enable bits [63:32]
BCM2838_ARM_INTERRUPT_FIQ3_CLR_EN_2 = $000001E8; Write to Clear ARM Core 3 FIQ enable bits [79:64]
 
BCM2838_ARM_INTERRUPT_SWIRQ_SET = $000001F0; Write to Set Software Interrupt sources
BCM2838_ARM_INTERRUPT_SWIRQ_CLEAR = $000001F4; Write to Clear Software Interrupt sources
 
BCM2838_ARM_INTERRUPT_CORE_OFFSET = BCM2838_ARM_INTERRUPT_IRQ1_PENDING0 - BCM2838_ARM_INTERRUPT_IRQ0_PENDING0; Offset between Core registers
BCM2838_ARM_INTERRUPT_FIQ_OFFSET = BCM2838_ARM_INTERRUPT_FIQ0_PENDING0 - BCM2838_ARM_INTERRUPT_IRQ0_PENDING0; Offset betwwen IRQ and FIQ registers


BCM2838 ARM timer BCM2838_ARM_TIMER_*
See: Section 14.2
 
BCM2838_ARM_TIMER_CONTROL_COUNTER_PRESCALE = ($FF shl 16); Free running counter pre-scaler (Freq is sys_clk/(prescale+1))
BCM2838_ARM_TIMER_CONTROL_COUNTER_ENABLED = (1 shl 9); 0 : Free running counter Disabled / 1 : Free running counter Enabled
BCM2838_ARM_TIMER_CONTROL_DEBUG_HALT = (1 shl 8); 0 : Timers keeps running if ARM is in debug halted mode / 1 : Timers halted if ARM is in debug halted mode
BCM2838_ARM_TIMER_CONTROL_TIMER_ENABLED = (1 shl 7); 0 : Timer disabled / 1 : Timer enabled
BCM2838_ARM_TIMER_CONTROL_INT_ENABLED = (1 shl 5); 0 : Timer interrupt disabled / 1 : Timer interrupt enabled
BCM2838_ARM_TIMER_CONTROL_PRESCALE = (3 shl 2); Pre-scale bits: 00 : pre-scale is clock / 1 (No pre-scale) / 01 : pre-scale is clock / 16 / 10 : pre-scale is clock / 256 / 11 : pre-scale is clock / 1
BCM2838_ARM_TIMER_CONTROL_32BIT = (1 shl 1); 0 : 16-bit counters / 1 : 32-bit counter
BCM2838_ARM_TIMER_CONTROL_ONESHOT = (1 shl 0); 0 = wrapping mode (default) / 1 = one-shot mode (Not supported by BCM2838)
 
BCM2838_ARM_TIMER_RAW_IRQ_PENDING = (1 shl 0); 0 : The interrupt pending bits is clear / 1 : The interrupt pending bit is set
 
BCM2838_ARM_TIMER_MASKED_IRQ_PENDING = (1 shl 0); 0 : Interrupt line not asserted / 1 :Interrupt line is asserted, (the interrupt pending and the interrupt enable bit are set)
 
BCM2838_ARM_TIMER_PREDIVIDER_MASK = ($3FF shl 0); Pre-divider value (timer_clock = apb_clock/(pre_divider+1))


BCM2838 power management, reset controller and watchdog BCM2838_PM_*
BCM2838_PM_PASSWORD = $5A000000;  
 
BCM2838_PM_RSTC_WRCFG_CLR = $FFFFFFCF;  
BCM2838_PM_RSTC_WRCFG_SET= $00000030;  
BCM2838_PM_RSTC_WRCFG_FULL_RESET = $00000020;  
BCM2838_PM_RSTC_RESET = $00000102;  
 
BCM2838_PM_RSTS_HADPOR_SET = $00001000;  
BCM2838_PM_RSTS_HADSRH_SET = $00000400;  
BCM2838_PM_RSTS_HADSRF_SET = $00000200;  
BCM2838_PM_RSTS_HADSRQ_SET = $00000100;  
BCM2838_PM_RSTS_HADWRH_SET = $00000040;  
BCM2838_PM_RSTS_HADWRF_SET = $00000020;  
BCM2838_PM_RSTS_HADWRQ_SET = $00000010;  
BCM2838_PM_RSTS_HADDRH_SET = $00000004;  
BCM2838_PM_RSTS_HADDRF_SET = $00000002;  
BCM2838_PM_RSTS_HADDRQ_SET = $00000001;  
 
BCM2838_PM_RSTS_RASPBERRYPI_HALT = $00000555; Special value to tell the Raspberry Pi firmware not to reboot, sets Boot Partition to 63 (0x3f).
 
BCM2838_PM_WDOG_RESET = $00000000;  
BCM2838_PM_WDOG_TIME_MASK = $000FFFFF;  
 
BCM2838_PM_WDOG_TICKS_PER_SECOND = (1 shl 16);  
BCM2838_PM_WDOG_TICKS_PER_MILLISECOND = (BCM2838_PM_WDOG_TICKS_PER_SECOND div 1000);  


BCM2838 random number generator BCM2838_RNG_*
BCM2838_RNG_CTRL_OFFSET = $00;  
BCM2838_RNG_CTRL_RNG_RBGEN_MASK = $00001FFF;  
BCM2838_RNG_CTRL_RNG_RBGEN_ENABLE = $00000001;  
BCM2838_RNG_CTRL_RNG_RBGEN_DISABLE = $00000000;  
BCM2838_RNG_CTRL_RNG_DIV_CTRL_SHIFT = 13;  
 
BCM2838_RNG_SOFT_RESET_OFFSET = $04;  
BCM2838_RNG_SOFT_RESET = $00000001;  
 
BCM2838_RBG_SOFT_RESET_OFFSET = $08;  
BCM2838_RBG_SOFT_RESET = $00000001;  
 
BCM2838_RNG_TOTAL_BIT_COUNT_OFFSET = $0C;  
 
BCM2838_RNG_TOTAL_BIT_COUNT_THRESHOLD_OFFSET = $10;  
 
BCM2838_RNG_INT_STATUS_OFFSET = $18;  
BCM2838_RNG_INT_STATUS_MASTER_FAIL_LOCKOUT_IRQ_MASK = $80000000;  
BCM2838_RNG_INT_STATUS_STARTUP_TRANSITIONS_MET_IRQ_MASK = $00020000;  
BCM2838_RNG_INT_STATUS_NIST_FAIL_IRQ_MASK = $00000020;  
BCM2838_RNG_INT_STATUS_TOTAL_BITS_COUNT_IRQ_MASK = $00000001;  
 
BCM2838_RNG_INT_ENABLE_OFFSET = $1C;  
 
BCM2838_RNG_FIFO_DATA_OFFSET = $20;  
 
BCM2838_RNG_FIFO_COUNT_OFFSET = $24;  
BCM2838_RNG_FIFO_COUNT_RNG_FIFO_COUNT_MASK = $000000FF;  
BCM2838_RNG_FIFO_COUNT_RNG_FIFO_THRESHOLD_SHIFT = 8;  


BCM2838 clock management BCM2838_CM_*
See: Section 6
 
BCM2838_CM_PASSWORD = $5A000000;  


BCM2838 clock manager control BCM2838_CM_CTL_*
See: Section 6.3
 
BCM2838_CM_CTL_MASH_0 = (0 shl 9); MASH control - 0 = integer division
BCM2838_CM_CTL_MASH_1 = (1 shl 9); MASH control - 1 = 1-stage MASH (equivalent to non-MASH dividers)
BCM2838_CM_CTL_MASH_2 = (2 shl 9); MASH control - 2 = 2-stage MASH
BCM2838_CM_CTL_MASH_3 = (3 shl 9); MASH control - 3 = 3-stage MASH (To avoid lock-ups and glitches do not change this control while BUSY=1 and do not change this control at the same time as asserting ENAB)
BCM2838_CM_CTL_FLIP = (1 shl 8); MASH control - Invert the clock generator output (To avoid output glitches do not switch this control while BUSY=1)
BCM2838_CM_CTL_BUSY = (1 shl 7); Clock generator is running (To avoid glitches and lock-ups, clock sources and setups must not be changed while this flag is set)
BCM2838_CM_CTL_GATE = (1 shl 6); Unused
BCM2838_CM_CTL_KILL = (1 shl 5); Kill the clock generator (0 = no action / 1 = stop and reset the clock generator) (This is intended for test/debug only)
BCM2838_CM_CTL_ENAB = (1 shl 4); Enable the clock generator
 
BCM2838_CM_CTL_SRC_GND = (0 shl 0); Clock source - 0 Hz GND
BCM2838_CM_CTL_SRC_OSC = (1 shl 0); Clock source - 54 MHz Oscillator
BCM2838_CM_CTL_SRC_TESTDEBUG0 = (2 shl 0); Clock source - 0 Hz Testdebug0
BCM2838_CM_CTL_SRC_TESTDEBUG1 = (3 shl 0); Clock source - 0 Hz Testdebug1
BCM2838_CM_CTL_SRC_PLLA = (4 shl 0); Clock source - 0 Hz PLLA
BCM2838_CM_CTL_SRC_PLLC = (5 shl 0); Clock source - 1000 MHz PLLC (changes with overclock settings)
BCM2838_CM_CTL_SRC_PLLD = (6 shl 0); Clock source - 750 MHz PLLD
BCM2838_CM_CTL_SRC_HDMI = (7 shl 0); Clock source - Unused


BCM2838 clock manager divisor BCM2838_CM_DIV_*
See: Section 6.3
 
BCM2838_CM_DIV_INT_MASK = $00FFF000; Integer part of divisor (This value has a minimum limit determined by the MASH setting) (To avoid lock-ups and glitches do not change this control while BUSY=1)
BCM2838_CM_DIV_FRAC_MASK = $00000FFF; Fractional part of divisor (To avoid lock-ups and glitches do not change this control while BUSY=1)


BCM2838 clock manager BCM2838_CM_*
BCM2838_CM_GNRICCTL = $00000000; Generic Clock Control
BCM2838_CM_GNRICDIV = $00000004; Generic Clock Divisor
BCM2838_CM_VPUCTL = $00000008; VPU Clock Control
BCM2838_CM_VPUDIV = $0000000C; VPU Clock Divisor
BCM2838_CM_SYSCTL = $00000010; System Clock Control
BCM2838_CM_SYSDIV = $00000014; System Clock Divisor
BCM2838_CM_PERIACTL = $00000018; PERIA Clock Control
BCM2838_CM_PERIADIV = $0000001C; PERIA Clock Divisor
BCM2838_CM_PERIICTL = $00000020; PERII Clock Control
BCM2838_CM_PERIIDIV = $00000024; PERII Clock Divisor
BCM2838_CM_H264CTL = $00000028; H264 Clock Control
BCM2838_CM_H264DIV = $0000002C; H264 Clock Divisor
BCM2838_CM_ISPCTL = $00000030; ISP Clock Control
BCM2838_CM_ISPDIV = $00000034; ISP Clock Divisor
BCM2838_CM_V3DCTL = $00000038; V3D Clock Control
BCM2838_CM_V3DDIV = $0000003C; V3D Clock Divisor
BCM2838_CM_CAM0CTL = $00000040; Camera 0 Clock Control
BCM2838_CM_CAM0DIV = $00000044; Camera 0 Clock Divisor
BCM2838_CM_CAM1CTL = $00000048; Camera 1 Clock Control
BCM2838_CM_CAM1DIV = $0000004C; Camera 1 Clock Divisor
BCM2838_CM_CCP2CTL = $00000050; CCP2 Clock Control
BCM2838_CM_CCP2DIV = $00000054; CCP2 Clock Divisor
BCM2838_CM_DSI0ECTL = $00000058; DSI0E Clock Control
BCM2838_CM_DSI0EDIV = $0000005C; DSI0E Clock Divisor
BCM2838_CM_DSI0PCTL = $00000060; DSI0P Clock Control
BCM2838_CM_DSI0PDIV = $00000064; DSI0P Clock Divisor
BCM2838_CM_DPICTL = $00000068; DPI Clock Control
BCM2838_CM_DPIDIV = $0000006C; DPI Clock Divisor
BCM2838_CM_GP0CTL = $00000070; General Purpose 0 Clock Control
BCM2838_CM_GP0DIV = $00000074; General Purpose 0 Clock Divisor
BCM2838_CM_GP1CTL = $00000078; General Purpose 1 Clock Control
BCM2838_CM_GP1DIV = $0000007C; General Purpose 1 Clock Divisor
BCM2838_CM_GP2CTL = $00000080; General Purpose 2 Clock Control
BCM2838_CM_GP2DIV = $00000084; General Purpose 2 Clock Divisor
BCM2838_CM_HSMCTL = $00000088; HSM Clock Control
BCM2838_CM_HSMDIV = $0000008C; HSM Clock Divisor
BCM2838_CM_OTPCTL = $00000090; OTP Clock Control
BCM2838_CM_OTPDIV = $00000094; OTP Clock Divisor
BCM2838_CM_PCMCTL = $00000098; PCM / I2S Clock Control
BCM2838_CM_PCMDIV = $0000009C; PCM / I2S Clock Divisor
BCM2838_CM_PWMCTL = $000000A0; PWM Clock Control
BCM2838_CM_PWMDIV = $000000A4; PWM Clock Divisor
BCM2838_CM_SLIMCTL = $000000A8; SLIM Clock Control
BCM2838_CM_SLIMDIV = $000000AC; SLIM Clock Divisor
BCM2838_CM_SMICTL = $000000B0; SMI Clock Control
BCM2838_CM_SMIDIV = $000000B4; SMI Clock Divisor
BCM2838_CM_TCNTCTL = $000000C0; TCNT Clock Control
BCM2838_CM_TCNTDIV = $000000C4; TCNT Clock Divisor
BCM2838_CM_TECCTL = $000000C8; TEC Clock Control
BCM2838_CM_TECDIV = $000000CC; TEC Clock Divisor
BCM2838_CM_TD0CTL = $000000D0; TD0 Clock Control
BCM2838_CM_TD0DIV = $000000D4; TD0 Clock Divisor
BCM2838_CM_TD1CTL = $000000D8; TD1 Clock Control
BCM2838_CM_TD1DIV = $000000DC; TD1 Clock Divisor
BCM2838_CM_TSENSCTL = $000000E0; TSENS Clock Control
BCM2838_CM_TSENSDIV = $000000E4; TSENS Clock Divisor
BCM2838_CM_TIMERCTL = $000000E8; Timer Clock Control
BCM2838_CM_TIMERDIV = $000000EC; Timer Clock Divisor
BCM2838_CM_UARTCTL = $000000F0; UART Clock Control
BCM2838_CM_UARTDIV = $000000F4; UART Clock Divisor
BCM2838_CM_VECCTL = $000000F8; VEC Clock Control
BCM2838_CM_VECDIV = $000000FC; VEC Clock Divisor
 
BCM2838_CM_OSCCOUNT = $00000100; Oscillator Count
BCM2838_CM_PLLA = $00000104; PLLA
BCM2838_CM_PLLC = $00000108; PLLC
BCM2838_CM_PLLD = $0000010C; PLLD
BCM2838_CM_PLLH = $00000110; PLLH
BCM2838_CM_LOCK = $00000114; Lock
BCM2838_CM_EVENT = $00000118; Event
BCM2838_CM_INTEN = $00000118; INTEN
BCM2838_CM_DSI0HSCK = $00000120; DSI0HSCK
BCM2838_CM_CKSM = $00000124; CKSM
BCM2838_CM_OSCFREQI = $00000128; Oscillator Frequency Integer
BCM2838_CM_OSCFREQF = $0000012C; Oscillator Frequency Fraction
BCM2838_CM_PLLTCTL = $00000130; PLLT Control
BCM2838_CM_PLLTCNT0 = $00000134; PLLT0 Count
BCM2838_CM_PLLTCNT1 = $00000138; PLLT1 Count
BCM2838_CM_PLLTCNT2 = $0000013C; PLLT2 Count
BCM2838_CM_PLLTCNT3 = $00000140; PLLT3 Count
BCM2838_CM_TDCLKEN = $00000144; TD Clock Enable
BCM2838_CM_BURSTCTL = $00000148; Burst Control
BCM2838_CM_BURSTCNT = $0000014C; Burst Count
BCM2838_CM_DSI1ECTL = $00000158; DSI1E Clock Control
BCM2838_CM_DSI1EDIV = $0000015C; DSI1E Clock Divisor
BCM2838_CM_DSI1PCTL = $00000160; DSI1P Clock Control
BCM2838_CM_DSI1PDIV = $00000164; DSI1P Clock Divisor
BCM2838_CM_DFTCTL = $00000168; DFT Clock Control
BCM2838_CM_DFTDIV = $0000016C; DFT Clock Divisor
BCM2838_CM_PLLB = $00000170; PLLB
 
BCM2838_CM_PULSECTL = $00000190; Pulse Clock Control
BCM2838_CM_PULSEDIV = $00000194; Pulse Clock Divisor
BCM2838_CM_SDCCTL = $000001A8; SDC Clock Control
BCM2838_CM_SDCDIV = $000001AC; SDC Clock Divisor
BCM2838_CM_ARMCTL = $000001B0; ARM Clock Control
BCM2838_CM_ARMDIV = $000001B4; ARM Clock Divisor
BCM2838_CM_AVEOCTL = $000001B8; AVEO Clock Control
BCM2838_CM_AVEODIV = $000001BC; AVEO Clock Divisor
BCM2838_CM_EMMCCTL = $000001C0; EMMC Clock Control
BCM2838_CM_EMMCDIV = $000001C4; EMMC Clock Divisor


BCM2838 mailbox BCM2838_MAILBOX_*
BCM2838_MAILBOX_0 = 0;  
BCM2838_MAILBOX_1 = 1;  


BCM2838 mailbox 0 channel BCM2838_MAILBOX0_CHANNEL_*
See: https://github.com/raspberrypi/firmware/wiki/Mailboxes
 
BCM2838_MAILBOX0_CHANNEL_POWER_MGMT = 0;  
BCM2838_MAILBOX0_CHANNEL_FRAMEBUFFER = 1;  
BCM2838_MAILBOX0_CHANNEL_UART = 2;  
BCM2838_MAILBOX0_CHANNEL_VCHIQ = 3;  
BCM2838_MAILBOX0_CHANNEL_LEDS = 4;  
BCM2838_MAILBOX0_CHANNEL_BUTTONS = 5;  
BCM2838_MAILBOX0_CHANNEL_TOUCHSCREEN = 6;  
BCM2838_MAILBOX0_CHANNEL_UNKNOWN = 7;  
BCM2838_MAILBOX0_CHANNEL_PROPERTYTAGS_ARMVC = 8;  
BCM2838_MAILBOX0_CHANNEL_PROPERTYTAGS_VCARM = 9;  


BCM2838 mailbox 1 channel BCM2838_MAILBOX_*_MASK*
See: https://github.com/raspberrypi/firmware/wiki/Mailboxes
Currently unknown
 
The BCM2838 mailboxes pass 28-bit messages (The low 4 bits of the 32-bit value are used to specify the channel)
BCM2838_MAILBOX_CHANNEL_MASK = $0000000F;  
BCM2838_MAILBOX_DATA_MASK = $FFFFFFF0;  


BCM2838 mailbox status flag BCM2838_MAILBOX_STATUS_*
BCM2838_MAILBOX_STATUS_FULL = $80000000;  
BCM2838_MAILBOX_STATUS_EMPTY = $40000000;  


BCM2838 mailbox configuration flag BCM2838_MAILBOX_CONFIG_*
BCM2838_MAILBOX_CONFIG_IRQENABLE = $00000001;  


BCM2838 mailbox property tag BCM2838_MBOX_TAG_GET_*
See: https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface or \include\soc\bcm2835\raspberrypi-firmware.h
 
VideoCore
BCM2838_MBOX_TAG_GET_FIRMWARE_REV = $00000001;  
Hardware
BCM2838_MBOX_TAG_GET_BOARD_MODEL = $00010001;  
BCM2838_MBOX_TAG_GET_BOARD_REV = $00010002;  
 
BCM2838_MBOX_TAG_GET_MAC_ADDRESS = $00010003;  
 
BCM2838_MBOX_TAG_GET_BOARD_SERIAL = $00010004;  
 
BCM2838_MBOX_TAG_GET_ARM_MEMORY = $00010005;  
BCM2838_MBOX_TAG_GET_VC_MEMORY = $00010006;  
 
BCM2838_MBOX_TAG_GET_CLOCKS = $00010007;  
Shared Resource Management
BCM2838_MBOX_TAG_GET_POWER_STATE = $00020001; Response indicates current state
BCM2838_MBOX_TAG_GET_TIMING = $00020002; Response indicates wait time required after turning a device on before power is stable
BCM2838_MBOX_TAG_SET_POWER_STATE = $00028001; Response indicates new state, with/without waiting for the power to become stable.
 
BCM2838_MBOX_TAG_GET_CLOCK_STATE = $00030001;  
BCM2838_MBOX_TAG_SET_CLOCK_STATE = $00038001;  
 
BCM2838_MBOX_TAG_GET_CLOCK_RATE = $00030002;  
BCM2838_MBOX_TAG_SET_CLOCK_RATE = $00038002;  
 
BCM2838_MBOX_TAG_GET_CLOCK_MAX_RATE = $00030004; Return the maximum supported clock rate for the given clock. Clocks should not be set higher than this.
BCM2838_MBOX_TAG_GET_CLOCK_MIN_RATE = $00030007; Return the minimum supported clock rate for the given clock. This may be used when idle.
 
BCM2838_MBOX_TAG_GET_TURBO = $00030009; Get the turbo state for index id. id should be 0. level will be zero for non-turbo and one for turbo.
BCM2838_MBOX_TAG_SET_TURBO = $00038009; Set the turbo state for index id. id should be zero. level will be zero for non-turbo and one for turbo. This will cause GPU clocks to be set to maximum when enabled and minimum when disabled.
 
BCM2838_MBOX_TAG_GET_STC = $0003000b;  
Voltage
BCM2838_MBOX_TAG_GET_VOLTAGE = $00030003; The voltage value may be clamped to the supported range. A value of 0x80000000 means the id was not valid.
BCM2838_MBOX_TAG_SET_VOLTAGE = $00038003; The voltage value may be clamped to the supported range. A value of 0x80000000 means the id was not valid.
 
BCM2838_MBOX_TAG_GET_MAX_VOLTAGE = $00030005; Return the maximum supported voltage rate for the given id. Voltages should not be set higher than this.
BCM2838_MBOX_TAG_GET_MIN_VOLTAGE = $00030008; Return the minimum supported voltage rate for the given id. This may be used when idle.
BCM2838_MBOX_TAG_GET_TEMP = $00030006; Return the temperature of the SoC in thousandths of a degree C. id should be zero.
BCM2838_MBOX_TAG_GET_MAX_TEMP = $0003000a; Return the maximum safe temperature of the SoC in thousandths of a degree C. id should be zero. Overclock may be disabled above this temperature.
GPU
BCM2838_MBOX_TAG_ALLOCATE_MEMORY = $0003000c; Allocates contiguous memory on the GPU. size and alignment are in bytes.
BCM2838_MBOX_TAG_LOCK_MEMORY = $0003000d; Lock buffer in place, and return a bus address. Must be done before memory can be accessed.
BCM2838_MBOX_TAG_UNLOCK_MEMORY = $0003000e; Unlock buffer. It retains contents, but may move. Needs to be locked before next use. status=0 is success.
BCM2838_MBOX_TAG_RELEASE_MEMORY = $0003000f; Free the memory buffer. status=0 is success.
 
BCM2838_MBOX_TAG_EXECUTE_CODE = $00030010; Calls the function at given (bus) address and with arguments given. E.g. r0 = fn(r0, r1, r2, r3, r4, r5); It blocks until call completes
BCM2838_MBOX_TAG_EXECUTE_QPU = $00030011; Execute an assembled block of code using one or more Quad Processing Units (QPUs)
BCM2838_MBOX_TAG_ENABLE_QPU = $00030012; Enable the Quad Processing Units (QPUs)
 
BCM2838_MBOX_TAG_GET_DISPMANX_HANDLE = $00030014; Gets the mem_handle associated with a created dispmanx resource. This can be locked and the memory directly written from the arm to avoid having to copy the image data to GPU.
BCM2838_MBOX_TAG_GET_EDID_BLOCK = $00030020; This reads the specified EDID block from attached HDMI/DVI device. There will always be at least one block of 128 bytes, but there may be additional blocks. You should keep requesting blocks (starting from 0) until the status returned is non-zero.
 
BCM2838_MBOX_TAG_GET_CUSTOMER_OTP = $00030021;  
BCM2838_MBOX_TAG_SET_CUSTOMER_OTP = $00038021;  
 
BCM2838_MBOX_TAG_GET_DOMAIN_STATE = $00030030;  
BCM2838_MBOX_TAG_SET_DOMAIN_STATE = $00038030;  
 
BCM2838_MBOX_TAG_GET_GPIO_STATE = $00030041; Get the current state of a GPIO expander pin
BCM2838_MBOX_TAG_SET_GPIO_STATE = $00038041; Set the current state of a GPIO expander pin
 
BCM2838_MBOX_TAG_SET_SDHOST_CLOCK = $00038042; Tell the firmware the SD Host clock setting so it will be adjusted for changes in core frequency
 
BCM2838_MBOX_TAG_GET_GPIO_CONFIG = $00030043; Get the current configuration of a GPIO expander pin
BCM2838_MBOX_TAG_SET_GPIO_CONFIG = $00038043; Set the current configuration of a GPIO expander pin
 
BCM2838_MBOX_TAG_GET_THROTTLED = $00030046;  
 
BCM2838_MBOX_TAG_GET_PERIPH_REG = $00030045;  
BCM2838_MBOX_TAG_SET_PERIPH_REG = $00038045;  
Frame Buffer
BCM2838_MBOX_TAG_ALLOCATE_BUFFER = $00040001; If the requested alignment is unsupported then the current base and size (which may be 0 if not allocated) is returned and no change occurs
BCM2838_MBOX_TAG_RELEASE_BUFFER = $00048001; Releases and disables the frame buffer
 
BCM2838_MBOX_TAG_SET_BLANK_SCREEN = $00040002;  
BCM2838_MBOX_TAG_TST_BLANK_SCREEN = $00044002;  
 
BCM2838_MBOX_TAG_GET_PHYSICAL_W_H = $00040003; Note that the "physical (display)" size is the size of the allocated buffer in memory, not the resolution of the video signal sent to the display device.
BCM2838_MBOX_TAG_TEST_PHYSICAL_W_H = $00044003;  
BCM2838_MBOX_TAG_SET_PHYSICAL_W_H = $00048003;  
 
BCM2838_MBOX_TAG_GET_VIRTUAL_W_H = $00040004; Note that the "virtual (buffer)" size is the portion of buffer that is sent to the display device, not the resolution the buffer itself. This may be smaller than the allocated buffer size in order to implement panning.
BCM2838_MBOX_TAG_TEST_VIRTUAL_W_H = $00044004;  
BCM2838_MBOX_TAG_SET_VIRTUAL_W_H = $00048004;  
 
BCM2838_MBOX_TAG_GET_DEPTH = $00040005;  
BCM2838_MBOX_TAG_TEST_DEPTH = $00044005;  
BCM2838_MBOX_TAG_SET_DEPTH = $00048005;  
 
BCM2838_MBOX_TAG_GET_PIXEL_ORDER = $00040006;  
BCM2838_MBOX_TAG_TEST_PIXEL_ORDER = $00044006;  
BCM2838_MBOX_TAG_SET_PIXEL_ORDER = $00048006;  
 
BCM2838_MBOX_TAG_GET_ALPHA_MODE = $00040007;  
BCM2838_MBOX_TAG_TEST_ALPHA_MODE = $00044007;  
BCM2838_MBOX_TAG_SET_ALPHA_MODE = $00048007;  
 
BCM2838_MBOX_TAG_GET_PITCH = $00040008;  
BCM2838_MBOX_TAG_TST_PITCH = $00044008;  
BCM2838_MBOX_TAG_SET_PITCH = $00048008;  
 
BCM2838_MBOX_TAG_GET_VIRTUAL_OFFSET = $00040009; Offset of physical display window within virtual buffer
BCM2838_MBOX_TAG_TEST_VIRTUAL_OFFSET = $00044009;  
BCM2838_MBOX_TAG_SET_VIRTUAL_OFFSET = $00048009;  
 
BCM2838_MBOX_TAG_GET_OVERSCAN = $0004000a;  
BCM2838_MBOX_TAG_TEST_OVERSCAN = $0004400a;  
BCM2838_MBOX_TAG_SET_OVERSCAN = $0004800a;  
 
BCM2838_MBOX_TAG_GET_PALETTE = $0004000b;  
BCM2838_MBOX_TAG_TEST_PALETTE = $0004400b;  
BCM2838_MBOX_TAG_SET_PALETTE = $0004800b;  
 
BCM2838_MBOX_TAG_GET_TOUCHBUF = $0004000f;  
BCM2838_MBOX_TAG_SET_TOUCHBUF = $0004801f;  
 
BCM2838_MBOX_TAG_GET_GPIOVIRTBUF = $00040010;  
BCM2838_MBOX_TAG_SET_GPIOVIRTBUF = $00048020;  
 
BCM2838_MBOX_TAG_GET_LAYER = $0004000c;  
BCM2838_MBOX_TAG_TST_LAYER = $0004400c;  
BCM2838_MBOX_TAG_SET_LAYER = $0004800c;  
 
BCM2838_MBOX_TAG_GET_TRANSFORM = $0004000d;  
BCM2838_MBOX_TAG_TST_TRANSFORM = $0004400d;  
BCM2838_MBOX_TAG_SET_TRANSFORM = $0004800d;  
 
BCM2838_MBOX_TAG_TST_VSYNC = $0004400e;  
BCM2838_MBOX_TAG_SET_VSYNC = $0004800e;  
 
BCM2838_MBOX_TAG_SET_BACKLIGHT = $0004800f;  
 
BCM2838_MBOX_TAG_GET_DISPLAY_ID = $00040016;  
BCM2838_MBOX_TAG_SET_DISPLAY_NUM = $00048013;  
BCM2838_MBOX_TAG_GET_NUM_DISPLAYS = $00040013;  
BCM2838_MBOX_TAG_GET_DISPLAY_SETTINGS = $00040014;  
 
BCM2838_MBOX_TAG_SET_PLANE = $00048015;  
BCM2838_MBOX_TAG_GET_DISPLAY_TIMING = $00040017;  
BCM2838_MBOX_TAG_SET_TIMING = $00048017;  
BCM2838_MBOX_TAG_GET_DISPLAY_CFG = $00040018;  
BCM2838_MBOX_TAG_SET_DISPLAY_POWER = $00048019;  
 
BCM2838_MBOX_TAG_SET_CURSOR_INFO = $00008010; 00008011 These were reversed in the documentation, see Linux \include\soc\bcm2835\raspberrypi-firmware.h
BCM2838_MBOX_TAG_SET_CURSOR_STATE = $00008011; 00008010
VCHIQ
BCM2838_MBOX_TAG_VCHIQ_INIT = $00048010;  
Config
BCM2838_MBOX_TAG_GET_COMMAND_LINE = $00050001;  
Shared Resource Management
BCM2838_MBOX_TAG_GET_DMA_CHANNELS = $00060001; Caller assumes that the VC has enabled all the usable DMA channels
End
BCM2838_MBOX_TAG_END = $00000000;  


BCM2838 mailbox board revision value BCM2838_BOARD_REV_*
See: http://elinux.org/RPi_HardwareHistory
 
BCM2838_BOARD_REV_2B_1 = $00A01041;  
BCM2838_BOARD_REV_2B_2 = $00A21041;  
BCM2838_BOARD_REV_2B_3 = $00A22042;  
 
BCM2838_BOARD_REV_3B_1 = $00A02082;  
BCM2838_BOARD_REV_3B_2 = $00A22082;  
BCM2838_BOARD_REV_3B_3 = $00A32082;  
 
BCM2838_BOARD_REV_CM3_1 = $00A020A0;  
BCM2838_BOARD_REV_CM3_2 = $00A220A0;  
 
BCM2838_BOARD_REV_MASK = $00FFFFFF; Mask off the warranty bit


BCM2838 mailbox board revision BCM2838_BOARD_REVISION_*
See: https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
 
BCM2838_BOARD_REVISION_PCB_MASK = ($F shl 0); PCB Revision Number
 
BCM2838_BOARD_REVISION_MODEL_MASK = ($FF shl 4); Model Number
BCM2838_BOARD_REVISION_MODEL_A = (0 shl 4); Model A (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_B = (1 shl 4); Model B (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_APLUS = (2 shl 4); Model A+ (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_BPLUS = (3 shl 4); Model B+ (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_2B = (4 shl 4); Model 2B (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_ALPHA = (5 shl 4); Unknown
BCM2838_BOARD_REVISION_MODEL_COMPUTE = (6 shl 4); Compute Module (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_UNKNOWN = (7 shl 4); Unknown
BCM2838_BOARD_REVISION_MODEL_3B = (8 shl 4); Model 3B (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_ZERO = (9 shl 4); Model Zero (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_COMPUTE3 = (10 shl 4); Compute Module 3 (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_UNKNOWN_2 = (11 shl 4); Unknown
BCM2838_BOARD_REVISION_MODEL_ZERO_W = (12 shl 4); Model Zero W (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_3BPLUS = (13 shl 4); Model 3B+ (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_3APLUS = (14 shl 4); Model 3A+ (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_COMPUTE3PLUS = (16 shl 4); Compute Module 3+ (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_MODEL_4B = (17 shl 4); Model 4B
BCM2838_BOARD_REVISION_MODEL_400 = (19 shl 4); Pi 400
BCM2838_BOARD_REVISION_MODEL_CM4 = (20 shl 4); Compute Module 4
 
BCM2838_BOARD_REVISION_PROCESSOR_MASK = ($F shl 12); Processor Type
BCM2838_BOARD_REVISION_PROCESSOR_BCM2835 = (0 shl 12); BCM2835 (Cannot occur on BCM2838)
BCM2838_BOARD_REVISION_PROCESSOR_BCM2836 = (1 shl 12); BCM2836
BCM2838_BOARD_REVISION_PROCESSOR_BCM2837 = (2 shl 12); BCM2837
BCM2838_BOARD_REVISION_PROCESSOR_BCM2838 = (3 shl 12); BCM2838
 
BCM2838_BOARD_REVISION_MANUFACTURER_MASK = ($F shl 16); Manufacturer
BCM2838_BOARD_REVISION_MANUFACTURER_SONY = (0 shl 16); Sony
BCM2838_BOARD_REVISION_MANUFACTURER_EGOMAN = (1 shl 16); Egoman
BCM2838_BOARD_REVISION_MANUFACTURER_EMBEST = (2 shl 16); Embest
BCM2838_BOARD_REVISION_MANUFACTURER_SONY_JAPAN = (3 shl 16); Sony (Japan)
BCM2838_BOARD_REVISION_MANUFACTURER_EMBEST2 = (4 shl 16); Embest
BCM2838_BOARD_REVISION_MANUFACTURER_STADIUM = (5 shl 16); Stadium
 
BCM2838_BOARD_REVISION_MEMORY_MASK = ($7 shl 20); Memory Size
BCM2838_BOARD_REVISION_MEMORY_256M = (0 shl 20); 256M
BCM2838_BOARD_REVISION_MEMORY_512M = (1 shl 20); 512M
BCM2838_BOARD_REVISION_MEMORY_1024M = (2 shl 20); 1024M
BCM2838_BOARD_REVISION_MEMORY_2048M = (3 shl 20); 2048M
BCM2838_BOARD_REVISION_MEMORY_4096M = (4 shl 20); 4096M
BCM2838_BOARD_REVISION_MEMORY_8192M = (5 shl 20); 8192M
 
BCM2838_BOARD_REVISION_ENCODED_FLAG = (1 shl 23); Encoded Flag, if set then revision uses this encoding.
 
BCM2838_BOARD_REVISION_MASK = $00FFFFFF; Mask off the warranty bits


BCM2838 mailbox tag power state device BCM2838_MBOX_POWER_DEVID_*
BCM2838_MBOX_POWER_DEVID_SDHCI = 0;  
BCM2838_MBOX_POWER_DEVID_UART0 = 1;  
BCM2838_MBOX_POWER_DEVID_UART1 = 2;  
BCM2838_MBOX_POWER_DEVID_USB_HCD = 3;  
BCM2838_MBOX_POWER_DEVID_I2C0 = 4;  
BCM2838_MBOX_POWER_DEVID_I2C1 = 5;  
BCM2838_MBOX_POWER_DEVID_I2C2 = 6;  
BCM2838_MBOX_POWER_DEVID_SPI = 7;  
BCM2838_MBOX_POWER_DEVID_CCP2TX = 8;  
 
BCM2838_MBOX_POWER_DEVID_UNKNOWN = $FFFFFFFF;  


BCM2838 mailbox tag power state request BCM2838_MBOX_SET_POWER_STATE_REQ_*
BCM2838_MBOX_SET_POWER_STATE_REQ_OFF = (0 shl 0);  
BCM2838_MBOX_SET_POWER_STATE_REQ_ON = (1 shl 0);  
BCM2838_MBOX_SET_POWER_STATE_REQ_WAIT = (1 shl 1);  


BCM2838 mailbox tag power state response BCM2838_MBOX_POWER_STATE_RESP_*
BCM2838_MBOX_POWER_STATE_RESP_OFF = (0 shl 0);  
BCM2838_MBOX_POWER_STATE_RESP_ON = (1 shl 0);  
BCM2838_MBOX_POWER_STATE_RESP_NODEV = (1 shl 1); Device doesn't exist


BCM2838 mailbox tag clock state/rate id BCM2838_MBOX_CLOCK_ID_*
BCM2838_MBOX_CLOCK_ID_RESERVED = 0;  
BCM2838_MBOX_CLOCK_ID_EMMC = 1;  
BCM2838_MBOX_CLOCK_ID_UART = 2;  
BCM2838_MBOX_CLOCK_ID_ARM = 3;  
BCM2838_MBOX_CLOCK_ID_CORE = 4;  
BCM2838_MBOX_CLOCK_ID_V3D = 5;  
BCM2838_MBOX_CLOCK_ID_H264 = 6;  
BCM2838_MBOX_CLOCK_ID_ISP = 7;  
BCM2838_MBOX_CLOCK_ID_SDRAM = 8;  
BCM2838_MBOX_CLOCK_ID_PIXEL = 9;  
BCM2838_MBOX_CLOCK_ID_PWM = 10;  
BCM2838_MBOX_CLOCK_ID_HEVC = 11;  
BCM2838_MBOX_CLOCK_ID_EMMC2 = 12;  
BCM2838_MBOX_CLOCK_ID_M2MC = 13;  
BCM2838_MBOX_CLOCK_ID_PIXEL_BVB = 14;  
 
BCM2838_MBOX_CLOCK_ID_UNKNOWN = $FFFFFFFF;  


BCM2838 mailbox tag clock state request BCM2838_MBOX_SET_CLOCK_STATE__REQ_*
BCM2838_MBOX_SET_CLOCK_STATE_REQ_OFF = (0 shl 0);  
BCM2838_MBOX_SET_CLOCK_STATE_REQ_ON = (1 shl 0);  
BCM2838_MBOX_SET_CLOCK_STATE_REQ_NOCLOCK = (1 shl 1); Clock doesn't exist


BCM2838 mailbox tag clock state response BCM2838_MBOX_CLOCK_STATE_RESP_ *
BCM2838_MBOX_CLOCK_STATE_RESP_OFF = (0 shl 0);  
BCM2838_MBOX_CLOCK_STATE_RESP_ON = (1 shl 0);  
BCM2838_MBOX_CLOCK_STATE_RESP_NOCLOCK = (1 shl 1); Clock doesn't exist


BCM2838 mailbox tag clock rate turbo BCM2838_MBOX_CLOCK_RATE_*
BCM2838_MBOX_CLOCK_RATE_REQ_SKIP_TURBO = (1 shl 0);  


BCM2838 mailbox tag voltage id BCM2838_MBOX_VOLTAGE_ID_*
BCM2838_MBOX_VOLTAGE_ID_RESERVED = $00000000;  
BCM2838_MBOX_VOLTAGE_ID_CORE = $00000001;  
BCM2838_MBOX_VOLTAGE_ID_SDRAM_C = $00000002;  
BCM2838_MBOX_VOLTAGE_ID_SDRAM_P = $00000003;  
BCM2838_MBOX_VOLTAGE_ID_SDRAM_I = $00000004;  


BCM2838 mailbox tag voltage BCM2838_MBOX_VOLTAGE_*
BCM2838_MBOX_VOLTAGE_INVALID = $80000000; A value of 0x80000000 means the id was not valid


BCM2838 mailbox tag temperature id BCM2838_MBOX_TEMP_ID_*
BCM2838_MBOX_TEMP_ID_SOC = 0;  


BCM2838 mailbox display id BCM2838_MBOX_DISPLAY_ID_*
Note: These are compatible with the DISPMANX_ID_* values
 
BCM2838_MBOX_DISPLAY_ID_MAIN_LCD = 0;  
BCM2838_MBOX_DISPLAY_ID_AUX_LCD = 1;  
BCM2838_MBOX_DISPLAY_ID_HDMI0 = 2;  
BCM2838_MBOX_DISPLAY_ID_SDTV = 3;  
BCM2838_MBOX_DISPLAY_ID_FORCE_LCD = 4;  
BCM2838_MBOX_DISPLAY_ID_FORCE_TV = 5;  
BCM2838_MBOX_DISPLAY_ID_FORCE_OTHER = 6; Non-default display
BCM2838_MBOX_DISPLAY_ID_HDMI1 = 7;  
BCM2838_MBOX_DISPLAY_ID_FORCE_TV2 = 8;  


BCM2838 mailbox tag memory flag BCM2838_MBOX_MEM_FLAG_*
BCM2838_MBOX_MEM_FLAG_DISCARDABLE = (1 shl 0); Can be resized to 0 at any time. Use for cached data.
BCM2838_MBOX_MEM_FLAG_NORMAL = (0 shl 2); Normal allocating alias. Don't use from ARM.
BCM2838_MBOX_MEM_FLAG_DIRECT = (1 shl 2); 0xC alias uncached
BCM2838_MBOX_MEM_FLAG_COHERENT = (2 shl 2); 0x8 alias. Non-allocating in L2 but coherent
BCM2838_MBOX_MEM_FLAG_L1_NONALLOCATING = (BCM2838_MBOX_MEM_FLAG_DIRECT or BCM2838_MBOX_MEM_FLAG_COHERENT); Allocating in L2
BCM2838_MBOX_MEM_FLAG_ZERO = (1 shl 4); Initialise buffer to all zeros
BCM2838_MBOX_MEM_FLAG_NO_INIT = (1 shl 5); Don't initialise (default is initialise to all ones)
BCM2838_MBOX_MEM_FLAG_HINT_PERMALOCK = (1 shl 6); Likely to be locked for long periods of time


BCM2838 mailbox tag blank screen BCM2838_MBOX_BLANK_SCREEN_*
BCM2838_MBOX_BLANK_SCREEN_REQ_ON = (1 shl 0);  


BCM2838 mailbox tag pixel order BCM2838_MBOX_PIXEL_ORDER_*
BCM2838_MBOX_PIXEL_ORDER_BGR = 0;  
BCM2838_MBOX_PIXEL_ORDER_RGB = 1;  


BCM2838 mailbox tag alpha mode BCM2838_MBOX_ALPHA_MODE_*
BCM2838_MBOX_ALPHA_MODE_0_OPAQUE = 0;  
BCM2838_MBOX_ALPHA_MODE_0_TRANSPARENT = 1;  
BCM2838_MBOX_ALPHA_MODE_IGNORED = 2;  


BCM2838 mailbox tag palette BCM2838_MBOX_PALETTE_*
BCM2838_MBOX_PALETTE_INVALID = $00000001;  


BCM2838 mailbox tag cursor state BCM2838_MBOX_CURSOR_*
BCM2838_MBOX_CURSOR_INVISIBLE = 0;  
BCM2838_MBOX_CURSOR_VISIBLE = 1;  


BCM2838 mailbox tag cursor state flag BCM2838_MBOX_CURSOR_STATE_*
BCM2838_MBOX_CURSOR_STATE_DISPLAY_COORDS = (0 shl 0);  
BCM2838_MBOX_CURSOR_STATE_FRAMEBUFFER_COORDS = (1 shl 0);  


BCM2838 mailbox tag cursor BCM2838_MBOX_CURSOR_INVALID*
BCM2838_MBOX_CURSOR_INVALID = $00000001;  


BCM2838 mailbox request/response BCM2838_MBOX_REQUEST_*
BCM2838_MBOX_REQUEST_CODE = $00000000;  
BCM2838_MBOX_RESPONSE_CODE_SUCCESS = $80000000;  
BCM2838_MBOX_RESPONSE_CODE_ERROR = $80000001;  


BCM2838 mailbox tag request/response BCM2838_MBOX_TAG_REQUEST_*
BCM2838_MBOX_TAG_REQUEST_CODE = $00000000;  
BCM2838_MBOX_TAG_RESPONSE_CODE = $80000000;  


BCM2838 GPIO BCM2838_GPIO_*
BCM2838_GPIO_PIN_COUNT = 58;  
BCM2838_GPIO_BANK_COUNT = 2;  
 
BCM2838_GPIO_SIGNATURE = $6770696F; The ASCII value 'GPIO' returned when reading from a write only register


BCM2838 virtual GPIO BCM2838_VIRTUAL_GPIO_*
BCM2838_VIRTUAL_GPIO_PIN_COUNT = 2; Raspberry Pi 4B only


BCM2838 function select register BCM2838_GP*
BCM2838_GPFSEL0 = $00000000; GPIO Function Select 0
BCM2838_GPFSEL1 = $00000004; GPIO Function Select 1
BCM2838_GPFSEL2 = $00000008; GPIO Function Select 2
BCM2838_GPFSEL3 = $0000000C; GPIO Function Select 3
BCM2838_GPFSEL4 = $00000010; GPIO Function Select 4
BCM2838_GPFSEL5 = $00000014; GPIO Function Select 5
 
Pin Output Set Registers
BCM2838_GPSET0 = $0000001C; GPIO Pin Output Set 0
BCM2838_GPSET1 = $00000020; GPIO Pin Output Set 1
 
Pin Output Clear Registers
BCM2838_GPCLR0 = $00000028; GPIO Pin Output Clear 0
BCM2838_GPCLR1 = $0000002C; GPIO Pin Output Clear 1
 
Pin Level Registers
BCM2838_GPLEV0 = $00000034; GPIO Pin Level 0
BCM2838_GPLEV1 = $00000038; GPIO Pin Level 1
 
Pin Event Detect Status Registers
BCM2838_GPEDS0 = $00000040; GPIO Pin Event Detect Status 0
BCM2838_GPEDS1 = $00000044; GPIO Pin Event Detect Status 1
 
Pin Rising Edge Detect Enable Registers
BCM2838_GPREN0 = $0000004c; GPIO Pin Rising Edge Detect Enable 0
BCM2838_GPREN1 = $00000050; GPIO Pin Rising Edge Detect Enable 1
 
Pin Falling Edge Detect Enable Registers
BCM2838_GPFEN0 = $00000058; GPIO Pin Falling Edge Detect Enable 0
BCM2838_GPFEN1 = $0000005c; GPIO Pin Falling Edge Detect Enable 1
 
Pin High Detect Enable Registers
BCM2838_GPHEN0 = $00000064; GPIO Pin High Detect Enable 0
BCM2838_GPHEN1 = $00000068; GPIO Pin High Detect Enable 1
 
Pin Low Detect Enable Registers
BCM2838_GPLEN0 = $00000070; GPIO Pin Low Detect Enable 0
BCM2838_GPLEN1 = $00000074; GPIO Pin Low Detect Enable 1
 
Pin Async. Rising Edge Detect Registers
BCM2838_GPAREN0 = $0000007c; GPIO Pin Async. Rising Edge Detect 0
BCM2838_GPAREN1 = $00000080; GPIO Pin Async. Rising Edge Detect 1
 
Pin Async. Falling Edge Detect Registers
BCM2838_GPAFEN0 = $00000088; GPIO Pin Async. Falling Edge Detect 0
BCM2838_GPAFEN1 = $0000008c; GPIO Pin Async. Falling Edge Detect 1
 
Pin Mux Register (See: https://github.com/raspberrypi/documentation/issues/1209)
BCM2838_GPPINMUX = $000000D0;  
 
Pin Pull-up/down Mode Registers
BCM2838_GPPUD0 = $000000E4; GPIO Pin Pull-up/down Mode 0
BCM2838_GPPUD1 = $000000E8; GPIO Pin Pull-up/down Mode 1
BCM2838_GPPUD2 = $000000EC; GPIO Pin Pull-up/down Mode 2
BCM2838_GPPUD3 = $000000F0; GPIO Pin Pull-up/down Mode 3
 
Function Select Mask
BCM2838_GPFSEL_MASK = 7;  
 
Function Select Values
BCM2838_GPFSEL_IN = 0;  
BCM2838_GPFSEL_OUT = 1;  
BCM2838_GPFSEL_ALT0 = 4;  
BCM2838_GPFSEL_ALT1 = 5;  
BCM2838_GPFSEL_ALT2 = 6;  
BCM2838_GPFSEL_ALT3 = 7;  
BCM2838_GPFSEL_ALT4 = 3;  
BCM2838_GPFSEL_ALT5 = 2;  
 
Pin Output Set Mask
BCM2838_GPSET_MASK = 1;  
 
Pin Output Clear Mask
BCM2838_GPCLR_MASK = 1;  
 
Pin Level Mask
BCM2838_GPLEV_MASK = 1;  
 
Pin Event Detect Status Mask
BCM2838_GPEDS_MASK = 1;  
 
Pin Rising Edge Detect Enable Mask
BCM2838_GPREN_MASK = 1;  
 
Pin Falling Edge Detect Enable Mask
BCM2838_GPFEN_MASK = 1;  
 
Pin High Detect Enable Mask
BCM2838_GPHEN_MASK = 1;  
 
Pin Low Detect Enable Mask
BCM2838_GPLEN_MASK = 1;  
 
Pin Async. Rising Edge Detect Mask
BCM2838_GPAREN_MASK = 1;  
 
Pin Async. Falling Edge Detect Mask
BCM2838_GPAFEN_MASK = 1;  
 
Pull-up/down Mode Mask
BCM2838_GPPUD_MASK = 3;  
 
Pull-up/down Mode Values
BCM2838_GPPUD_NONE = 0;  
BCM2838_GPPUD_UP = 1;  
BCM2838_GPPUD_DOWN = 2;  
 
Pin Mux Values
BCM2838_GPPINMUX_RGMII_PHY_GPIO = 1; If set enables the RGMII PHY signals onto GPIOs 46+
BCM2838_GPPINMUX_LEGACY_EMMC = 2; If set legacy EMMC controller (Arasan SD) is connected to the SD card socket


BCM2838 ARM local BCM2838_ARM_LOCAL_*
BCM2838_ARM_LOCAL_BASE = $FF800000;  
BCM2838_ARM_LOCAL_SIZE = SIZE_8M;  


BCM2838 ARM local peripheral BCM2838_ARM_*_REGS_ BASE*
See: BCM2711 ARM Peripherals
 
BCM2838_ARM_LOCAL_REGS_BASE = (BCM2838_ARM_LOCAL_BASE + $0000);  
 
GICv2
BCM2838_GICDIST_REGS_BASE = BCM2838_ARM_LOCAL_BASE + $41000;  
BCM2838_GICCPU_REGS_BASE = BCM2838_ARM_LOCAL_BASE + $42000;  


BCM2838 IRQ local ARM peripheral BCM2838_IRQ_LOCAL_ARM_*
See: BCM2711 ARM Peripherals
 
ARM Generic Timers
BCM2838_IRQ_LOCAL_ARM_CNTPSIRQ = BCM2838_IRQ_TIMER0;  
BCM2838_IRQ_LOCAL_ARM_CNTPNSIRQ = BCM2838_IRQ_TIMER1;  
BCM2838_IRQ_LOCAL_ARM_CNTVIRQ = BCM2838_IRQ_TIMER2;  
BCM2838_IRQ_LOCAL_ARM_CNTHPIRQ = BCM2838_IRQ_TIMER3;  
ARM Malboxes0-3
BCM2838_IRQ_LOCAL_ARM_MAILBOX0:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX0_0, BCM2838_IRQ_MAILBOX0_1, BCM2838_IRQ_MAILBOX0_2, BCM2838_IRQ_MAILBOX0_3);  
 
BCM2838_IRQ_LOCAL_ARM_MAILBOX1:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX1_0, BCM2838_IRQ_MAILBOX1_1, BCM2838_IRQ_MAILBOX1_2, BCM2838_IRQ_MAILBOX1_3);  
 
BCM2838_IRQ_LOCAL_ARM_MAILBOX2:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX2_0, BCM2838_IRQ_MAILBOX2_1, BCM2838_IRQ_MAILBOX2_2, BCM2838_IRQ_MAILBOX2_3);  
 
BCM2838_IRQ_LOCAL_ARM_MAILBOX3:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_MAILBOX3_0, BCM2838_IRQ_MAILBOX3_1, BCM2838_IRQ_MAILBOX3_2, BCM2838_IRQ_MAILBOX3_3);  
ARM Performance Monitoring
BCM2838_IRQ_LOCAL_ARM_PMU:array[0..BCM2838_CPU_COUNT - 1] of LongWord = (BCM2838_IRQ_PMU0, BCM2838_IRQ_PMU1, BCM2838_IRQ_PMU2, BCM2838_IRQ_PMU3);  
AXI Outstanding
BCM2838_IRQ_LOCAL_ARM_AXIQUIET = BCM2838_IRQ_LOCAL_AXIQUIET;  
ARM Local Timer
BCM2838_IRQ_LOCAL_ARM_TIMER = BCM2838_IRQ_LOCAL_TIMER;  
AXI Error
BCM2838_IRQ_LOCAL_ARM_AXIERR = BCM2838_IRQ_LOCAL_AXIERR;  


BCM2838 ARM local control BCM2838_ARM_LOCAL_CONTROL_*
See: Table 103 ARM_CONTROL register
 
BCM2838_ARM_LOCAL_CONTROL_AXIERRIRQ_DIS = (1 shl 6); Masks the AXI Error interrupt
BCM2838_ARM_LOCAL_CONTROL_AXIERRIRQ_EN = (0 shl 6); Enables the AXI Error interrupt
BCM2838_ARM_LOCAL_CONTROL_APB_CLOCK = (1 shl 7); 64-bit Core timer runs from the APB clock
BCM2838_ARM_LOCAL_CONTROL_CRYSTAL_CLOCK = (0 shl 7); 64-bit Core timer runs from the Crystal clock
BCM2838_ARM_LOCAL_CONTROL_INCREMENT_2 = (1 shl 8); 64-bit Core timer increments by 2
BCM2838_ARM_LOCAL_CONTROL_INCREMENT_1 = (0 shl 8); 64-bit Core timer increments by 1


BCM2838 ARM local core interrupt routing BCM2838_ARM_LOCAL_AXI_ERR_ *
See: Table 104 CORE_IRQ_CONTROL Register
 
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ0 = (0 shl 4); AXI_ERR IRQ goes to IRQ input of core 0
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ1 = (1 shl 4); AXI_ERR IRQ goes to IRQ input of core 1
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ2 = (2 shl 4); AXI_ERR IRQ goes to IRQ input of core 2
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_IRQ3 = (3 shl 4); AXI_ERR IRQ goes to IRQ input of core 3
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ0 = (4 shl 4); AXI_ERR FIQ goes to FIQ input of core 0
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ1 = (5 shl 4); AXI_ERR FIQ goes to FIQ input of core 1
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ2 = (6 shl 4); AXI_ERR FIQ goes to FIQ input of core 2
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_FIQ3 = (7 shl 4); AXI_ERR FIQ goes to FIQ input of core 3
 
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_MASK = (7 shl 4);  
BCM2838_ARM_LOCAL_AXI_ERR_INT_ROUTING_SHIFT = 4;  


BCM2838 ARM local PM interrupt routing set/clear BCM2838_ARM_LOCAL_PM_INT_ROUTING_*
See: Table 105/106 PMU_CONTROL_SET/CLR Register
 
BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ0 = (1 shl 0); Core 0 PM IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ1 = (1 shl 1); Core 1 PM IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ2 = (1 shl 2); Core 2 PM IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_IRQ3 = (1 shl 3); Core 3 PM IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ0 = (1 shl 4); Core 0 PM FIQ Enable (If set, this bit overrides the IRQ bit 0)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ1 = (1 shl 5); Core 1 PM FIQ Enable (If set, this bit overrides the IRQ bit 1)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ2 = (1 shl 6); Core 2 PM FIQ Enable (If set, this bit overrides the IRQ bit 2)
BCM2838_ARM_LOCAL_PM_INT_ROUTING_FIQ3 = (1 shl 7); Core 3 PM FIQ Enable (If set, this bit overrides the IRQ bit 3)


BCM2838 ARM local peripheral interrupt routing BCM2838_ARM_LOCAL_*
See: Table 107 PERI_IRQ_ROUTE0 Register
 
BCM2838_ARM_LOCAL_PERIPHERAL_WRITE_MASKS = ($01 shl 24); This field must be written with 0x01, otherwise changes to LOCAL_TIMER_IRQ will be ignored.
 
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ0 = (0 shl 0); Local timer interrupt goes to Core 0 IRQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ1 = (1 shl 0); Local timer interrupt goes to Core 1 IRQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ2 = (2 shl 0); Local timer interrupt goes to Core 2 IRQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_IRQ3 = (3 shl 0); Local timer interrupt goes to Core 3 IRQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ0 = (4 shl 0); Local timer interrupt goes to Core 0 FIQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ1 = (5 shl 0); Local timer interrupt goes to Core 1 FIQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ2 = (6 shl 0); Local timer interrupt goes to Core 2 FIQ
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_FIQ3 = (7 shl 0); Local timer interrupt goes to Core 3 FIQ
 
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_MASK = (7 shl 0);  
BCM2838_ARM_LOCAL_TIMER_INT_ROUTING_SHIFT = 0;  


BCM2838 ARM local AXI outstanding count BCM2838_ARM_LOCAL_AXI_COUNT_*
BCM2838_ARM_LOCAL_AXI_COUNT_READ_MASK = ($3FF shl 0); Outstanding reads counter
BCM2838_ARM_LOCAL_AXI_COUNT_WRITE_MASK = ($3FF shl 16); Outstanding writes counter


BCM2838 ARM local AXI outstanding IRQ BCM2838_ARM_LOCAL_AXI_QUIET_*
See: Table 108 AXI_QUIET_TIME Register
Core 0 Only
 
BCM2838_ARM_LOCAL_AXI_QUIET_IRQ_ENABLE = (1 shl 20);  
BCM2838_ARM_LOCAL_AXI_QUIET_IRQ_TIMEOUT = ($FFFFF shl 0);  


BCM2838 ARM local timer control BCM2838_ARM_LOCAL_TIMER_CONTROL_*
See: Table 109 LOCAL_TIMER_CONTROL Register
 
BCM2838_ARM_LOCAL_TIMER_CONTROL_INT_STATUS = (1 shl 31); Interrupt flag (Read Only)
BCM2838_ARM_LOCAL_TIMER_CONTROL_INT_ENABLE = (1 shl 29); Interrupt enable (1= enabled)
BCM2838_ARM_LOCAL_TIMER_CONTROL_ENABLE = (1 shl 28); Timer enable (1 = enabled)
BCM2838_ARM_LOCAL_TIMER_CONTROL_VALUE_MASK = ($0FFFFFFF shl 0); Re-load value


BCM2838 ARM local timer clear reload BCM2838_ARM_LOCAL_TIMER_CLEAR_*
See: Table 110 LOCAL_TIMER_IRQ Register
Write Only
 
BCM2838_ARM_LOCAL_TIMER_CLEAR_INT = (1 shl 31); Interrupt flag clear when written as 1 (Write Only)
BCM2838_ARM_LOCAL_TIMER_CLEAR_RELOAD = (1 shl 30); Local timer reloaded when written as 1 (Write Only)


BCM2838 ARM local timer interrupt control BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_*
See: Table 111 TIMER_CNTRL0, TIMER_CNTRL1, TIMER_CNTRL2 & TIMER_CNTRL3 Registers
Note: These are the ARM Generic Timers (See ARM Architecture Reference Manual)
 
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPSIRQ = (1 shl 0); Physical Secure Timer IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPNSIRQ = (1 shl 1); Physical Non Secure Timer IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTHPIRQ = (1 shl 2); Hypervisor Timer IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTVIRQ = (1 shl 3); Virtual Timer IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPSFIQ = (1 shl 4); Physical Secure Timer FIQ Enable (If set, this bit overrides the IRQ bit 0)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTPNSFIQ = (1 shl 5); Physical Non Secure Timer FIQ Enable (If set, this bit overrides the IRQ bit 1)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTHPFIQ = (1 shl 6); Hypervisor Timer FIQ Enable (If set, this bit overrides the IRQ bit 2)
BCM2838_ARM_LOCAL_TIMER_INT_CONTROL_CNTVFIQ = (1 shl 7); Virtual Timer FIQ Enable (If set, this bit overrides the IRQ bit 3)


BCM2838 ARM local mailbox interrupt control BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_*
See: Table 112 MAILBOX_CNTRL0, MAILBOX_CNTRL1, MAILBOX_CNTRL2 & MAILBOX_CNTRL3 Registers
 
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX0IRQ = (1 shl 0); Mailbox-0 IRQ Enable (This bit is only valid if bit 4 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX1IRQ = (1 shl 1); Mailbox-1 IRQ Enable (This bit is only valid if bit 5 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX2IRQ = (1 shl 2); Mailbox-2 IRQ Enable (This bit is only valid if bit 6 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX3IRQ = (1 shl 3); Mailbox-3 IRQ Enable (This bit is only valid if bit 7 is clear otherwise it is ignored)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX0FIQ = (1 shl 0); Mailbox-0 FIQ Enable (If set, this bit overrides the IRQ bit 0)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX1FIQ = (1 shl 0); Mailbox-1 FIQ Enable (If set, this bit overrides the IRQ bit 1)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX2FIQ = (1 shl 0); Mailbox-2 FIQ Enable (If set, this bit overrides the IRQ bit 2)
BCM2838_ARM_LOCAL_MAILBOX_INT_CONTROL_MAILBOX3FIQ = (1 shl 0); Mailbox-3 FIQ Enable (If set, this bit overrides the IRQ bit 3)


BCM2838 ARM local IRQ source BCM2838_ARM_LOCAL_IRQ_SOURCE_*
See: Table 113 IRQ_SOURCE0, IRQ_SOURCE1, IRQ_SOURCE2 & IRQ_SOURCE3 Registers
 
BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTPSIRQ = (1 shl 0); Physical Secure Timer Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTPNSIRQ = (1 shl 1); Physical Non Secure Timer Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTHPIRQ = (1 shl 2); Hypervisor Timer Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_CNTVIRQ = (1 shl 3); Virtual Timer Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX0 = (1 shl 4); Mailbox 0 Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX1 = (1 shl 5); Mailbox 1 Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX2 = (1 shl 6); Mailbox 2 Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_MAILBOX3 = (1 shl 7); Mailbox 3 Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_GPU = (1 shl 8); VideoCore Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_PMU = (1 shl 9); Performance Monitor Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_AXI_QUIET = (1 shl 10); AXI Outstanding Interrupt (Core 0 Only)
BCM2838_ARM_LOCAL_IRQ_SOURCE_TIMER = (1 shl 11); Local Timer Interrupt
BCM2838_ARM_LOCAL_IRQ_SOURCE_AXI_ERR = (1 shl 30); AXI error, as reported by the ARM L2 cache


BCM2838 ARM local FIQ source BCM2838_ARM_LOCAL_FIQ_SOURCE_*
See: Table 114 FIQ_SOURCE0, FIQ_SOURCE1, FIQ_SOURCE2 & FIQ_SOURCE3 Registers
 
BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTPSIRQ = (1 shl 0); Physical Secure Timer Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTPNSIRQ = (1 shl 1); Physical Non Secure Timer Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTHPIRQ = (1 shl 2); Hypervisor Timer Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_CNTVIRQ = (1 shl 3); Virtual Timer Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX0 = (1 shl 4); Mailbox 0 Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX1 = (1 shl 5); Mailbox 1 Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX2 = (1 shl 6); Mailbox 2 Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_MAILBOX3 = (1 shl 7); Mailbox 3 Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_GPU = (1 shl 8); VideoCore Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_PMU = (1 shl 9); Performance Monitor Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_TIMER = (1 shl 11); Local Timer Fast Interrupt
BCM2838_ARM_LOCAL_FIQ_SOURCE_AXI_ERR = (1 shl 30); AXI error, as reported by the ARM L2 cache


Type definitions



BCM2838 system timer registers

PBCM2838SystemTimerRegisters = ^TBCM2838SystemTimerRegisters;

TBCM2838SystemTimerRegisters = record

Note: Layout of the BCM2838 System Timer registers
CS:LongWord; System Timer Control/Status
CLO:LongWord; System Timer Counter Lower 32 bits
CHI:LongWord; System Timer Counter Higher 32 bits
C0:LongWord; System Timer Compare 0. Already used by the VideoCore GPU (Do not use)
C1:LongWord; System Timer Compare 1
C2:LongWord; System Timer Compare 2. Already used by the VideoCore GPU (Do not use)
C3:LongWord; System Timer Compare 3

BCM2838 DMA channel registers

PBCM2838DMARegisters = ^TBCM2838DMARegisters;

TBCM2838DMARegisters = record

Note: Layout of the BCM2838 DMA Channel registers
CS:LongWord; DMA Channel Control and Status
CONBLK_AD:LongWord; DMA Channel Control Block Address
TI:LongWord; DMA Channel CB Word 0 (Transfer Information)
SOURCE_AD:LongWord; DMA Channel CB Word 1 (Source Address)
DEST_AD:LongWord; DMA Channel CB Word 2 (Destination Address)
TXFR_LEN:LongWord; DMA Channel CB Word 3 (Transfer Length)
STRIDE:LongWord; DMA Channel CB Word 4 (2D Mode Stride) (Not applicable to Lite channels)
NEXTCONBK:LongWord; DMA Channel CB Word 5 (Next Control Block Address)
DEBUG:LongWord; DMA Channel Debug

BCM2838 DMA40 channel registers

PBCM2838DMA40Registers = ^TBCM2838DMA40Registers;

TBCM2838DMA40Registers = record

Note: Layout of the BCM2838 DMA40 Channel registers
CS:LongWord; {DMA Channel Control and Status  
CB:LongWord; {DMA Channel Control Block Address  
Reserved1:LongWord;  
DEBUG:LongWord; DMA Channel Debug
TI:LongWord; DMA Channel CB Word 0 (Transfer Information)
SRC:LongWord; DMA Channel CB Word 1 (Source Address)
SRCI:LongWord; DMA Channel CB Word 2 (Source Information)
DEST:LongWord; DMA Channel CB Word 3 (Destination Address)
DESTI:LongWord; DMA Channel CB Word 4 (Destination Information)
LEN:LongWord; DMA Channel CB Word 5 (Transfer Length)
NEXT_CB:LongWord; DMA Channel CB Word 6 (Next Control Block Address)
DEBUG2:LongWord; DMA Channel Debug

BCM2838 DMA control block structure

PBCM2838DMAControlBlock = ^TBCM2838DMAControlBlock;

TBCM2838DMAControlBlock = record

Note: Layout of BCM2838 DMA Control Block structure. Must be 32byte (256bit) aligned.
TransferInformation:LongWord;  
SourceAddress:LongWord;  
DestinationAddress:LongWord;  
TransferLength:LongWord;  
ModeStride:LongWord; Not applicable to Lite channels
NextControlBlockAddress:LongWord;  
Reserved1:LongWord;  
Reserved2:LongWord;  

BCM2838 DMA40 control block structure

PBCM2838DMA40ControlBlock = ^TBCM2838DMA40ControlBlock;

TBCM2838DMA40ControlBlock = record

Note: Layout of BCM2838 DMA40 Control Block structure. Must be 32byte (256bit) aligned.
TransferInformation:LongWord;  
SourceAddress:LongWord;  
SourceInformation:LongWord;  
DestinationAddress:LongWord;  
DestinationInformation:LongWord;  
TransferLength:LongWord;  
NextControlBlockAddress:LongWord;  
Reserved1:LongWord;  

BCM2838 BSC (I2C) registers

PBCM2838BSCRegisters = ^TBCM2838BSCRegisters;

TBCM2838BSCRegisters = record

Note: Layout of the BCM2838 BSC (I2C) registers
C:LongWord; Control
S:LongWord; Status
DLEN:LongWord; Data Length
A:LongWord; Slave Address
FIFO:LongWord; Data FIFO
CDIV:LongWord; Clock Divider
DEL:LongWord; Data Delay

BCM2838 SPI0 registers

PBCM2838SPI0Registers = ^TBCM2838SPI0Registers;

TBCM2838SPI0Registers = record

Note: Layout of the BCM2838 SPI0 registers
CS:LongWord; SPI Master Control and Status
FIFO:LongWord; SPI Master TX and RX FIFOs
CLK:LongWord; SPI Master Clock Divider
DLEN:LongWord; SPI Master Data Length
LTOH:LongWord; SPI LOSSI mode TOH
DC:LongWord; SPI DMA DREQ Controls

BCM2838 I2C/SPI slave registers

PBCM2838I2CSPIRegisters = ^TBCM2838I2CSPIRegisters;

TBCM2838I2CSPIRegisters = record

Note: Layout of the BCM2838 I2C/SPI Slave registers
DR:LongWord; Data Register
RSR:LongWord; Operation status register and error clear register
SLV:LongWord; I2C SPI Address Register holds the I2C slave address value
CR:LongWord; Control register is used to configure the I2C or SPI operation
FR:LongWord; Flag register
IFLS:LongWord; Interrupt fifo level select register
IMSC:LongWord; Interrupt Mask Set Clear Register
RIS:LongWord; Raw Interrupt Status Register
MIS:LongWord; Masked Interrupt Status Register
ICR:LongWord; Interrupt Clear Register
DMACR:LongWord; DMA Control Register
TDR:LongWord; FIFO Test Data Register
GPUSTAT:LongWord; GPU Status Register
HCTRL:LongWord; Host Control Register
DEBUG1:LongWord; I2C Debug Register
DEBUG2:LongWord; SPI Debug Register

BCM2838 AUX (UART1, SPI1 and SPI2) registers

PBCM2838AUXRegisters = ^TBCM2838AUXRegisters;

TBCM2838AUXRegisters = record

Note: Layout of the BCM2838 AUX (UART1, SPI1 and SPI2) registers
AUX_IRQ:LongWord; Auxiliary Interrupt status
AUX_ENABLE:LongWord; Auxiliary enables
Reserved01:LongWord;  
Reserved02:LongWord;  
Reserved03:LongWord;  
Reserved04:LongWord;  
Reserved05:LongWord;  
Reserved06:LongWord;  
Reserved07:LongWord;  
Reserved08:LongWord;  
Reserved09:LongWord;  
Reserved0A:LongWord;  
Reserved0B:LongWord;  
Reserved0C:LongWord;  
Reserved0D:LongWord;  
Reserved0E:LongWord;  
AUX_MU_IO:LongWord; Mini Uart I/O Data
AUX_MU_IER:LongWord; Mini Uart Interrupt Enable
AUX_MU_IIR:LongWord; Mini Uart Interrupt Identify
AUX_MU_LCR:LongWord; Mini Uart Line Control
AUX_MU_MCR:LongWord; Mini Uart Modem Control
AUX_MU_LSR:LongWord; Mini Uart Line Status
AUX_MU_MSR:LongWord; Mini Uart Modem Status
AUX_MU_SCRATCH:LongWord; Mini Uart Scratch
AUX_MU_CNTL:LongWord; Mini Uart Extra Control
AUX_MU_STAT:LongWord; Mini Uart Extra Status
AUX_MU_BAUD:LongWord; Mini Uart Baudrate
Reserved11:LongWord;  
Reserved12:LongWord;  
Reserved13:LongWord;  
Reserved14:LongWord;  
Reserved15:LongWord;  
AUX_SPI1_CNTL0:LongWord; SPI 1 Control register 0
AUX_SPI1_CNTL1:LongWord; SPI 1 Control register 1
AUX_SPI1_STAT:LongWord; SPI 1 Status
Reserved21:LongWord;  
AUX_SPI1_IO:LongWord; SPI 1 Data
AUX_SPI1_PEEK:LongWord; SPI 1 Peek
Reserved31:LongWord;  
Reserved32:LongWord;  
Reserved33:LongWord;  
Reserved34:LongWord;  
Reserved35:LongWord;  
Reserved36:LongWord;  
Reserved37:LongWord;  
Reserved38:LongWord;  
Reserved39:LongWord;  
Reserved3A:LongWord;  
AUX_SPI2_CNTL0:LongWord; SPI 2 Control register 0
AUX_SPI2_CNTL1:LongWord; SPI 2 Control register 1
AUX_SPI2_STAT:LongWord; SPI 2 Status
Reserved40:LongWord;  
AUX_SPI2_IO:LongWord; SPI 2 Data
AUX_SPI2_PEEK:LongWord; SPI 2 Peek

BCM2838 PCM/I2S registers

PBCM2838PCMRegisters = ^TBCM2838PCMRegisters;

TBCM2838PCMRegisters = record

Note: Layout of the BCM2838 PCM/I2S registers
CS_A:LongWord; PCM Control and Status
FIFO_A:LongWord; PCM FIFO Data
MODE_A:LongWord; PCM Mode
RXC_A:LongWord; PCM Receive Configuration
TXC_A:LongWord; PCM Transmit Configuration
DREQ_A:LongWord;  
INTEN_A:LongWord; PCM Interrupt Enables
INTSTC_A:LongWord; PCM Interrupt Status & Clear
GRAY:LongWord; PCM Gray Mode Control

BCM2838 pulse width modulator (PWM) registers

PBCM2838PWMRegisters = ^TBCM2838PWMRegisters;

TBCM2838PWMRegisters = record

Note: Layout of the BCM2838 Pulse Width Modulator (PWM) registers
CTL:LongWord; PWM Control
STA:LongWord; PWM Status
DMAC:LongWord; PWM DMA Configuration
Reserved1:LongWord;  
RNG1:LongWord; PWM Channel 1 Range
DAT1:LongWord; PWM Channel 1 Data
FIF1:LongWord; PWM FIFO Input
Reserved2:LongWord;  
RNG2:LongWord; PWM Channel 2 Range
DAT2:LongWord; PWM Channel 2 Data

BCM2838 PL011 UART registers

PBCM2838PL011Registers = ^TBCM2838PL011Registers;

TBCM2838PL011Registers = record

Note: Layout of the BCM2838 PL011 UART registers
DR:LongWord; Data Register
RSRECR:LongWord; Receive Status Register / Error Clear Register
Reserved01:LongWord;  
Reserved02:LongWord;  
Reserved03:LongWord;  
Reserved04:LongWord;  
FR:LongWord; Flag register
Reserved05:LongWord;  
ILPR:LongWord; Not in use
IBRD:LongWord; Integer Baud rate divisor
FBRD:LongWord; Fractional Baud rate divisor
LCRH:LongWord; Line Control register
CR:LongWord; Control register
IFLS:LongWord; Interrupt FIFO Level Select Register
IMSC:LongWord; Interrupt Mask Set Clear Register
RIS:LongWord; Raw Interrupt Status Register
MIS:LongWord; Masked Interrupt Status Register
ICR:LongWord; Interrupt Clear Register
DMACR:LongWord; DMA Control Register
Reserved11:LongWord;  
Reserved12:LongWord;  
Reserved13:LongWord;  
Reserved14:LongWord;  
Reserved15:LongWord;  
Reserved16:LongWord;  
Reserved17:LongWord;  
Reserved18:LongWord;  
Reserved19:LongWord;  
Reserved1A:LongWord;  
Reserved1B:LongWord;  
Reserved1C:LongWord;  
Reserved1D:LongWord;  
ITCR:LongWord; Test Control Register
ITIP:LongWord; Integration Test Input Register
ITOP:LongWord; Integration Test Output Register
TDR:LongWord; Test Data Register

BCM2838 ARM timer registers

PBCM2838ARMTimerRegisters = ^TBCM2838ARMTimerRegisters;

TBCM2838ARMTimerRegisters = record

Note: Layout of the BCM2838 ARM Timer registers
Load:LongWord; Timer Load register
Value:LongWord; Timer Value register
Control:LongWord; Timer control register
IRQClear:LongWord; Timer IRQ clear register
RawIRQ:LongWord; Timer Raw IRQ register
MaskedIRQ:LongWord; Timer Masked IRQ register
Reload:LongWord; Timer Reload register
Predivider:LongWord; The timer pre-divider register
Counter:LongWord; Free running counter

BCM2838 power management watchdog registers

PBCM2838PMWatchdogRegisters = ^TBCM2838PMWatchdogRegisters;

TBCM2838PMWatchdogRegisters = record

Note: Layout of the BCM2838 Power Management Watchdog registers
Reserved1:LongWord;  
Reserved2:LongWord;  
Reserved3:LongWord;  
Reserved4:LongWord;  
Reserved5:LongWord;  
Reserved6:LongWord;  
Reserved7:LongWord;  
RSTC:LongWord;  
RSTS:LongWord;  
WDOG:LongWord;  

BCM2838 random number generator registers

PBCM2838RNGRegisters = ^TBCM2838RNGRegisters;

TBCM2838RNGRegisters = record

Note: Layout of the BCM2838 Random Number Generator registers
Control:LongWord;  
SoftResetRNG:LongWord;  
SoftResetRBG:LongWord;  
TotalBitCount:LongWord;  
TBCThreshold:LongWord;  
Reserved1:LongWord;  
IntStatus:LongWord;  
IntEnable:LongWord;  
FIFOData:LongWord;  
FIFOCount:LongWord;  

BCM2838 GPIO registers

PBCM2838GPIORegisters = ^TBCM2838GPIORegisters;

TBCM2838GPIORegisters = record

Note: Layout of the BCM2838 GPIO registers
GPFSEL0:LongWord; GPIO Function Select 0
GPFSEL1:LongWord; GPIO Function Select 1
GPFSEL2:LongWord; GPIO Function Select 2
GPFSEL3:LongWord; GPIO Function Select 3
GPFSEL4:LongWord; GPIO Function Select 4
GPFSEL5:LongWord; GPIO Function Select 5
Reserved1:LongWord;  
GPSET0:LongWord; GPIO Pin Output Set 0
GPSET1:LongWord; GPIO Pin Output Set 1
Reserved2:LongWord;  
GPCLR0:LongWord; GPIO Pin Output Clear 0
GPCLR1:LongWord; GPIO Pin Output Clear 1
Reserved3:LongWord;  
GPLEV0:LongWord; GPIO Pin Level 0
GPLEV1:LongWord; GPIO Pin Level 1
Reserved4:LongWord;  
GPEDS0:LongWord; GPIO Pin Event Detect Status 0
GPEDS1:LongWord; GPIO Pin Event Detect Status 1
Reserved5:LongWord;  
GPREN0:LongWord; GPIO Pin Rising Edge Detect Enable 0
GPREN1:LongWord; GPIO Pin Rising Edge Detect Enable 1
Reserved6:LongWord;  
GPFEN0:LongWord; GPIO Pin Falling Edge Detect Enable 0
GPFEN1:LongWord; GPIO Pin Falling Edge Detect Enable 1
Reserved7:LongWord;  
GPHEN0:LongWord; GPIO Pin High Detect Enable 0
GPHEN1:LongWord; GPIO Pin High Detect Enable 1
Reserved8:LongWord;  
GPLEN0:LongWord; GPIO Pin Low Detect Enable 0
GPLEN1:LongWord; GPIO Pin Low Detect Enable 1
Reserved9:LongWord;  
GPAREN0:LongWord; GPIO Pin Async. Rising Edge Detect 0
GPAREN1:LongWord; GPIO Pin Async. Rising Edge Detect 1
Reserved10:LongWord;  
GPAFEN0:LongWord; GPIO Pin Async. Falling Edge Detect 0
GPAFEN1:LongWord; GPIO Pin Async. Falling Edge Detect 1
Reserved11:LongWord;  
Reserved12:LongWord;  
Reserved13:LongWord;  
Reserved14:LongWord;  
Reserved15:LongWord;  
Reserved16:LongWord;  
Reserved17:LongWord;  
Reserved18:LongWord;  
Reserved19:LongWord;  
Reserved20:LongWord;  
Reserved21:LongWord;  
Reserved22:LongWord;  
Reserved23:LongWord;  
Reserved24:LongWord;  
Reserved25:LongWord;  
Reserved26:LongWord;  
Reserved27:LongWord;  
Reserved28:LongWord;  
Reserved29:LongWord;  
Reserved30:LongWord;  
Reserved31:LongWord;  
GPPUD0:LongWord; GPIO Pin Pull-up/down Mode 0
GPPUD1:LongWord; GPIO Pin Pull-up/down Mode 1
GPPUD2:LongWord; GPIO Pin Pull-up/down Mode 2
GPPUD3:LongWord; GPIO Pin Pull-up/down Mode 3

BCM2838 mailbox0 registers

PBCM2838Mailbox0Registers = ^TBCM2838Mailbox0Registers;

TBCM2838Mailbox0Registers = record

Note: Layout of the BCM2838 Mailbox0 registers (See https://github.com/raspberrypi/firmware/wiki/Mailboxes)
Read:LongWord; Offset 0x00 (The read register for mailbox 0)
Reserved1:LongWord; Offset 0x04
Reserved2:LongWord; Offset 0x08
Reserved3:LongWord; Offset 0x0C
Peek:LongWord; Offset 0x10 (Read from the mailbox without removing data from it)
Sender:LongWord; Offset 0x14 (Sender ID (bottom 2 bits only))
Status:LongWord; Offset 0x18 (The status register for mailbox 0)
Config:LongWord; Offset 0x1C (The configuration register for mailbox 0)

BCM2838 mailbox1 registers

PBCM2838Mailbox1Registers = ^TBCM2838Mailbox1Registers;

TBCM2838Mailbox1Registers = record

Note: Layout of the BCM2838 Mailbox1 registers (See https://github.com/raspberrypi/firmware/wiki/Mailboxes)
Write:LongWord; Offset 0x00 (The write register for mailbox 0) (Also the read register for mailbox 1)
Reserved1:LongWord; Offset 0x04
Reserved2:LongWord; Offset 0x08
Reserved3:LongWord; Offset 0x0C
Reserved4:LongWord; Offset 0x10
Reserved5:LongWord; Offset 0x14
Status:LongWord; Offset 0x18 (The status register for mailbox 1)
Config:LongWord; Offset 0x1C (The configuration register for mailbox 1)

BCM2838 mailbox framebuffer request

PBCM2838MailboxFramebuffer = ^TBCM2838MailboxFramebuffer;

TBCM2838MailboxFramebuffer = record

Note: Layout of the BCM2838 Mailbox Framebuffer request (This structure must be 16 byte aligned when passed to the GPU)
PhysicalWidth:LongWord; Requested width of Physical Framebuffer
PhysicalHeight:LongWord; Requested height of Physical Framebuffer
VirtualWidth:LongWord; Requested width of Virtual Display
VirtualHeight:LongWord; Requested height of Virtual Display
Pitch:LongWord; Zero on request, Number of Bytes per Row in response
Depth:LongWord; Requested Colour Depth in Bits per Pixel
OffsetX:LongWord; Requested X offset of Virtual Framebuffer
OffsetY:LongWord; Requested Y offset of Virtual Framebuffer
Address:LongWord; Framebuffer address (Zero on request, Failure if zero in response)
Size:LongWord; Framebuffer size (Zero on request, Size in bytes in response)

BCM2838 mailbox header property tags

PBCM2838MailboxHeader = ^TBCM2838MailboxHeader;

TBCM2838MailboxHeader = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Header
Size:LongWord; Total buffer size in bytes (including the header values, the end tag and padding)
Code:LongWord; Request/response code

BCM2838 mailbox footer property tags

PBCM2838MailboxFooter = ^TBCM2838MailboxFooter;

TBCM2838MailboxFooter = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Footer
Tag:LongWord; BCM2838_MBOX_TAG_END

BCM2838 mailbox tag header

PBCM2838MailboxTagHeader = ^TBCM2838MailboxTagHeader;

TBCM2838MailboxTagHeader = record

Note: Layout of the BCM2838 Mailbox Property tags (These structures must be 16 byte aligned when passed to the GPU)
Tag Header
Tag:LongWord; Tag identifier
Size:LongWord; Value buffer size in bytes
Length:LongWord; 1 bit (MSB) request/response indicator (0=request, 1=response), 31 bits (LSB) value length in bytes

BCM2838 mailbox tag no request

PBCM2838MailboxTagNoRequest = ^TBCM2838MailboxTagNoRequest;

TBCM2838MailboxTagNoRequest = record

Tag No Request
   

BCM2838 mailbox tag no response

PBCM2838MailboxTagNoResponse = ^TBCM2838MailboxTagNoResponse;

TBCM2838MailboxTagNoResponse = record

Tag No Response
   

BCM2838 mailbox tag firmware revision response

TBCM2838MailboxTagFirmwareRevisionResponse = record

Get Firmware Revision
Revision:LongWord;  

BCM2838 mailbox tag get firmware revision

PBCM2838MailboxTagGetFirmwareRevision = ^TBCM2838MailboxTagGetFirmwareRevision;

TBCM2838MailboxTagGetFirmwareRevision = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagFirmwareRevisionResponse);  

BCM2838 mailbox tag board model response

TBCM2838MailboxTagBoardModelResponse = record

Get Board Model
Model:LongWord;  

BCM2838 mailbox tag get board model

PBCM2838MailboxTagGetBoardModel = ^TBCM2838MailboxTagGetBoardModel;

TBCM2838MailboxTagGetBoardModel = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagBoardModelResponse);  

BCM2838 mailbox tag board revision response

TBCM2838MailboxTagBoardRevisionResponse = record

Get Board Revision
Revision:LongWord;  

BCM2838 mailbox tag get board revision

PBCM2838MailboxTagGetBoardRevision = ^TBCM2838MailboxTagGetBoardRevision;

TBCM2838MailboxTagGetBoardRevision = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagBoardRevisionResponse);  

BCM2838 mailbox tag MAC address response

TBCM2838MailboxTagMACAddressResponse = record

Get MAC Address
MAC:array[0..5] of Byte; MAC address in network byte order
Padding:Word;  

BCM2838 mailbox tag get MAC address

PBCM2838MailboxTagGetMACAddress = ^TBCM2838MailboxTagGetMACAddress;

TBCM2838MailboxTagGetMACAddress = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagMACAddressResponse);  

BCM2838 mailbox tag board serial response

TBCM2838MailboxTagBoardSerialResponse = record

Get Board Serial
Serial:Int64;  

BCM2838 mailbox tag get board serial

PBCM2838MailboxTagGetBoardSerial = ^TBCM2838MailboxTagGetBoardSerial;

TBCM2838MailboxTagGetBoardSerial = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagBoardSerialResponse);  

BCM2838 mailbox tag ARM memory response

TBCM2838MailboxTagARMMemoryResponse = record

Get ARM Memory
Address:LongWord; Base address in bytes
Size:LongWord; Size in bytes

BCM2838 mailbox tag get ARM memory

PBCM2838MailboxTagGetARMMemory = ^TBCM2838MailboxTagGetARMMemory;

TBCM2838MailboxTagGetARMMemory = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagARMMemoryResponse);  

BCM2838 mailbox tag VC memory response

TBCM2838MailboxTagVCMemoryResponse = record

Get VC Memory
Address:LongWord; Base address in bytes
Size:LongWord; Size in bytes

BCM2838 mailbox tag get VC memory

PBCM2838MailboxTagGetVCMemory = ^TBCM2838MailboxTagGetVCMemory;

TBCM2838MailboxTagGetVCMemory = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagVCMemoryResponse);  

BCM2838 mailbox tag clock response

TBCM2838MailboxTagClockResponse = record

Get Clocks
ParentId:LongWord;  
ClockId:LongWord;  

BCM2838 mailbox tag clocks response

TBCM2838MailboxTagClocksResponse = record

Clocks:array[0..255] of TBCM2838MailboxTagClockResponse;  

BCM2838 mailbox tag get clocks

PBCM2838MailboxTagGetClocks = ^TBCM2838MailboxTagGetClocks;

TBCM2838MailboxTagGetClocks = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagClocksResponse);  

BCM2838 mailbox tag get power state request

TBCM2838MailboxTagGetPowerStateRequest = record

Get Power State
DeviceId:LongWord;  

BCM2838 mailbox tag power state response

TBCM2838MailboxTagPowerStateResponse = record

DeviceId:LongWord;  
State:LongWord;  

BCM2838 mailbox tag get power state

PBCM2838MailboxTagGetPowerState = ^TBCM2838MailboxTagGetPowerState;

TBCM2838MailboxTagGetPowerState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetPowerStateRequest);  
1:(Response:TBCM2838MailboxTagPowerStateResponse);  

BCM2838 mailbox tag timing request

TBCM2838MailboxTagTimingRequest = record

Get Timing
DeviceId:LongWord;  

BCM2838 mailbox tag timing response

TBCM2838MailboxTagTimingResponse = record

DeviceId:LongWord;  
Wait:LongWord; Enable wait time in microseconds

BCM2838 mailbox tag get timing

PBCM2838MailboxTagGetTiming = ^TBCM2838MailboxTagGetTiming;

TBCM2838MailboxTagGetTiming = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagTimingRequest);  
1:(Response:TBCM2838MailboxTagTimingResponse);  

BCM2838 mailbox tag set power state request

TBCM2838MailboxTagSetPowerStateRequest = record

Set Power State
DeviceId:LongWord;  
State:LongWord;  

BCM2838 mailbox tag set power state

PBCM2838MailboxTagSetPowerState = ^TBCM2838MailboxTagSetPowerState;

TBCM2838MailboxTagSetPowerState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetPowerStateRequest);  
1:(Response:TBCM2838MailboxTagPowerStateResponse);  

BCM2838 mailbox tag get clock state request

TBCM2838MailboxTagGetClockStateRequest = record

Get Clock State
ClockId:LongWord;  

BCM2838 mailbox tag clock state response

TBCM2838MailboxTagClockStateResponse = record

ClockId:LongWord;  
State:LongWord;  

BCM2838 mailbox tag get clock state

PBCM2838MailboxTagGetClockState = ^TBCM2838MailboxTagGetClockState;

TBCM2838MailboxTagGetClockState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetClockStateRequest);  
1:(Response:TBCM2838MailboxTagClockStateResponse);  

BCM2838 mailbox tag set clock state request

TBCM2838MailboxTagSetClockStateRequest = record

Set Clock State
ClockId:LongWord;  
State:LongWord;  

BCM2838 mailbox tag set clock state

PBCM2838MailboxTagSetClockState = ^TBCM2838MailboxTagSetClockState;

TBCM2838MailboxTagSetClockState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetClockStateRequest);  
1:(Response:TBCM2838MailboxTagClockStateResponse);  

BCM2838 mailbox tag get clock rate request

TBCM2838MailboxTagGetClockRateRequest = record

Get Clock Rate
ClockId:LongWord;  

BCM2838 mailbox tag clock rate response

TBCM2838MailboxTagClockRateResponse = record

ClockId:LongWord;  
Rate:LongWord; In Hz

BCM2838 mailbox tag get clock rate

PBCM2838MailboxTagGetClockRate = ^TBCM2838MailboxTagGetClockRate;

TBCM2838MailboxTagGetClockRate = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetClockRateRequest);  
1:(Response:TBCM2838MailboxTagClockRateResponse);  

BCM2838 mailbox tag set clock rate request

TBCM2838MailboxTagSetClockRateRequest = record

Set Clock Rate
ClockId:LongWord;  
Rate:LongWord; In Hz
SkipTurbo:LongWord;  

BCM2838 mailbox tag set clock rate

PBCM2838MailboxTagSetClockRate = ^TBCM2838MailboxTagSetClockRate;

TBCM2838MailboxTagSetClockRate = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetClockRateRequest);  
1:(Response:TBCM2838MailboxTagClockRateResponse);  

BCM2838 mailbox tag get clock max rate request

TBCM2838MailboxTagGetClockMaxRateRequest = record

Get Clock Max Rate
ClockId:LongWord;  

BCM2838 mailbox tag get clock max rate response

TBCM2838MailboxTagGetClockMaxRateResponse = record

ClockId:LongWord;  
Rate:LongWord; In Hz

BCM2838 mailbox tag get clock max rate

PBCM2838MailboxTagGetClockMaxRate = ^TBCM2838MailboxTagGetClockMaxRate;

TBCM2838MailboxTagGetClockMaxRate = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetClockMaxRateRequest);  
1:(Response:TBCM2838MailboxTagGetClockMaxRateResponse);  

BCM2838 mailbox tag get clock min rate

PBCM2838MailboxTagGetClockMinRate = ^TBCM2838MailboxTagGetClockMinRate;

TBCM2838MailboxTagGetClockMinRate = record

Get Clock Min Rate
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetClockMaxRateRequest);  
1:(Response:TBCM2838MailboxTagGetClockMaxRateResponse);  

BCM2838 mailbox tag get turbo request

TBCM2838MailboxTagGetTurboRequest = record

Get Turbo
Id:LongWord;  

BCM2838 mailbox tag turbo response

TBCM2838MailboxTagTurboResponse = record

Id:LongWord;  
Level:LongWord;  

BCM2838 mailbox tag get turbo

PBCM2838MailboxTagGetTurbo = ^TBCM2838MailboxTagGetTurbo;

TBCM2838MailboxTagGetTurbo = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetTurboRequest);  
1:(Response:TBCM2838MailboxTagTurboResponse);  

BCM2838 mailbox tag set turbo request

TBCM2838MailboxTagSetTurboRequest = record

Set Turbo
Id:LongWord;  
Level:LongWord;  

BCM2838 mailbox tag set turbo

PBCM2838MailboxTagSetTurbo = ^TBCM2838MailboxTagSetTurbo;

TBCM2838MailboxTagSetTurbo = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetTurboRequest);  
1:(Response:TBCM2838MailboxTagTurboResponse);  

BCM2838 mailbox tag get voltage request

TBCM2838MailboxTagGetVoltageRequest = record

Get Voltage
VoltageId:LongWord;  

BCM2838 mailbox tag voltage response

TBCM2838MailboxTagVoltageResponse = record

VoltageId:LongWord;  
Value:LongWord; Offset from 1.2V in units of 0.025V

BCM2838 mailbox tag get voltage

PBCM2838MailboxTagGetVoltage = ^TBCM2838MailboxTagGetVoltage;

TBCM2838MailboxTagGetVoltage = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetVoltageRequest);  
1:(Response:TBCM2838MailboxTagVoltageResponse);  

BCM2838 mailbox tag set voltage request

TBCM2838MailboxTagSetVoltageRequest = record

Set Voltage
VoltageId:LongWord;  
Value:LongWord; Offset from 1.2V in units of 0.025V

BCM2838 mailbox tag set voltage

PBCM2838MailboxTagSetVoltage = ^TBCM2838MailboxTagSetVoltage;

TBCM2838MailboxTagSetVoltage = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetVoltageRequest);  
1:(Response:TBCM2838MailboxTagVoltageResponse);  

BCM2838 mailbox tag get max voltage

PBCM2838MailboxTagGetMaxVoltage = ^TBCM2838MailboxTagGetMaxVoltage;

TBCM2838MailboxTagGetMaxVoltage = record

Get Max Voltage
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetVoltageRequest);  
1:(Response:TBCM2838MailboxTagVoltageResponse);  

BCM2838 mailbox tag get min voltage

PBCM2838MailboxTagGetMinVoltage = ^TBCM2838MailboxTagGetMinVoltage;

TBCM2838MailboxTagGetMinVoltage = record

Get Min Voltage
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetVoltageRequest);  
1:(Response:TBCM2838MailboxTagVoltageResponse);  

BCM2838 mailbox tag temperature request

TBCM2838MailboxTagTemperatureRequest = record

Get Temperature
TemperatureId:LongWord;  

BCM2838 mailbox tag temperature response

TBCM2838MailboxTagTemperatureResponse = record

TemperatureId:LongWord; Should be zero
Temperature:LongWord; Return the temperature of the SoC in thousandths of a degree C

BCM2838 mailbox tag get temperature

PBCM2838MailboxTagGetTemperature = ^TBCM2838MailboxTagGetTemperature;

TBCM2838MailboxTagGetTemperature = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagTemperatureRequest);  
1:(Response:TBCM2838MailboxTagTemperatureResponse);  

BCM2838 mailbox tag get max temperature

PBCM2838MailboxTagGetMaxTemperature = ^TBCM2838MailboxTagGetMaxTemperature;

TBCM2838MailboxTagGetMaxTemperature = record

Get Max Temp
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagTemperatureRequest);  
1:(Response:TBCM2838MailboxTagTemperatureResponse);  

BCM2838 mailbox tag allocate memory request

TBCM2838MailboxTagAllocateMemoryRequest = record

Allocate Memory
Size:LongWord;  
Alignment:LongWord;  
Flags:LongWord;  

BCM2838 mailbox tag allocate memory response

TBCM2838MailboxTagAllocateMemoryResponse = record

Handle:THandle;  

BCM2838 mailbox tag allocate memory

PBCM2838MailboxTagAllocateMemory = ^TBCM2838MailboxTagAllocateMemory;

TBCM2838MailboxTagAllocateMemory = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagAllocateMemoryRequest);  
1:(Response:TBCM2838MailboxTagAllocateMemoryResponse);  

BCM2838 mailbox tag lock memory request

TBCM2838MailboxTagLockMemoryRequest = record

Lock Memory
Handle:THandle;  

BCM2838 mailbox tag lock memory response

TBCM2838MailboxTagLockMemoryResponse = record

Address:LongWord; Bus Address

BCM2838 mailbox tag lock memory

PBCM2838MailboxTagLockMemory = ^TBCM2838MailboxTagLockMemory;

TBCM2838MailboxTagLockMemory = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagLockMemoryRequest);  
1:(Response:TBCM2838MailboxTagLockMemoryResponse);  

BCM2838 mailbox tag unlock memory response

TBCM2838MailboxTagUnlockMemoryResponse = record

Unlock Memory
Status:LongWord; 0 is Success

BCM2838 mailbox tag unlock memory

PBCM2838MailboxTagUnlockMemory = ^TBCM2838MailboxTagUnlockMemory;

TBCM2838MailboxTagUnlockMemory = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagLockMemoryRequest);  
1:(Response:TBCM2838MailboxTagUnlockMemoryResponse);  

BCM2838 mailbox tag release memory

PBCM2838MailboxTagReleaseMemory = ^TBCM2838MailboxTagReleaseMemory;

TBCM2838MailboxTagReleaseMemory = record

Release Memory
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagLockMemoryRequest);  
1:(Response:TBCM2838MailboxTagUnlockMemoryResponse);  

BCM2838 mailbox tag execute code request

TBCM2838MailboxTagExecuteCodeRequest = record

Execute Code
Address:Pointer; Bus Address
R0:LongWord;  
R1:LongWord;  
R2:LongWord;  
R3:LongWord;  
R4:LongWord;  
R5:LongWord;  

BCM2838 mailbox tag execute code response

TBCM2838MailboxTagExecuteCodeResponse = record

R0:LongWord;  

BCM2838 mailbox tag execute code

PBCM2838MailboxTagExecuteCode = ^TBCM2838MailboxTagExecuteCode;

TBCM2838MailboxTagExecuteCode = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagExecuteCodeRequest);  
1:(Response:TBCM2838MailboxTagExecuteCodeResponse);  

BCM2838 mailbox tag execute QPU request

TBCM2838MailboxTagExecuteQPURequest = record

Execute QPU
NumQPUs:LongWord;  
Control:LongWord;  
NoFlush:LongWord;  
Timeout:LongWord; Milliseconds

BCM2838 mailbox tag execute QPU response

TBCM2838MailboxTagExecuteQPUResponse = record

Status:LongWord; 0 is Success / 0x80000000 is Timeout

BCM2838 mailbox tag execute QPU

PBCM2838MailboxTagExecuteQPU = ^TBCM2838MailboxTagExecuteQPU;

TBCM2838MailboxTagExecuteQPU = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagExecuteQPURequest);  
1:(Response:TBCM2838MailboxTagExecuteQPUResponse);  

BCM2838 mailbox tag enable QPU request

TBCM2838MailboxTagEnableQPURequest = record

Enable QPU
Enable:LongWord;  

BCM2838 mailbox tag enable QPU response

TBCM2838MailboxTagEnableQPUResponse = record

Status:LongWord; 0 is Success

BCM2838 mailbox tag enable QPU

PBCM2838MailboxTagEnableQPU = ^TBCM2838MailboxTagEnableQPU;

TBCM2838MailboxTagEnableQPU = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagEnableQPURequest);  
1:(Response:TBCM2838MailboxTagEnableQPUResponse);  

BCM2838 mailbox tag get dispmanx handle request

TBCM2838MailboxTagGetDispmanxHandleRequest = record

Get Dispmanx Handle
Resource:THandle;  

BCM2838 mailbox tag get dispmanx handle response

TBCM2838MailboxTagGetDispmanxHandleResponse = record

Status:LongWord; 0 is Success
Memory:THandle;  

BCM2838 mailbox tag get dispmanx handle

PBCM2838MailboxTagGetDispmanxHandle = ^TBCM2838MailboxTagGetDispmanxHandle;

TBCM2838MailboxTagGetDispmanxHandle = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetDispmanxHandleRequest);  
1:(Response:TBCM2838MailboxTagGetDispmanxHandleResponse);  

BCM2838 mailbox tag get EDID block request

TBCM2838MailboxTagGetEDIDBlockRequest = record

Get EDID Block
Block:LongWord; Starting from 0

BCM2838 mailbox tag get EDID block response

TBCM2838MailboxTagGetEDIDBlockResponse = record

Block:LongWord; Starting from 0
Status:LongWord; 0 is Success
EDID:array[0..127] of Byte;  

BCM2838 mailbox tag get EDID block

PBCM2838MailboxTagGetEDIDBlock = ^TBCM2838MailboxTagGetEDIDBlock;

TBCM2838MailboxTagGetEDIDBlock = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetEDIDBlockRequest);  
1:(Response:TBCM2838MailboxTagGetEDIDBlockResponse);  

BCM2838 mailbox tag GPIO state request

TBCM2838MailboxTagGPIOStateRequest = record

Get GPIO State
GPIO:LongWord;  
State:LongWord;  

BCM2838 mailbox tag GPIO state response

TBCM2838MailboxTagGPIOStateResponse = record

GPIO:LongWord;  
State:LongWord;  

BCM2838 mailbox tag get GPIO state

PBCM2838MailboxTagGetGPIOState = ^TBCM2838MailboxTagGetGPIOState;

TBCM2838MailboxTagGetGPIOState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGPIOStateRequest);  
1:(Response:TBCM2838MailboxTagGPIOStateResponse);  

BCM2838 mailbox tag set GPIO state

PBCM2838MailboxTagSetGPIOState = ^TBCM2838MailboxTagSetGPIOState;

TBCM2838MailboxTagSetGPIOState = record

Set GPIO State
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGPIOStateRequest);  
1:(Response:TBCM2838MailboxTagGPIOStateResponse);  

BCM2838 mailbox tag get GPIO config request

TBCM2838MailboxTagGetGPIOConfigRequest = record

Get GPIO Config
GPIO:LongWord;  
Direction:LongWord;  
Polarity:LongWord;  
Terminator:LongWord;  
PullUp:LongWord;  

BCM2838 mailbox tag get GPIO config response

TBCM2838MailboxTagGetGPIOConfigResponse = record

GPIO:LongWord;  
Direction:LongWord;  
Polarity:LongWord;  
Terminator:LongWord;  
PullUp:LongWord;  

BCM2838 mailbox tag get GPIO config

PBCM2838MailboxTagGetGPIOConfig = ^TBCM2838MailboxTagGetGPIOConfig;

TBCM2838MailboxTagGetGPIOConfig = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetGPIOConfigRequest);  
1:(Response:TBCM2838MailboxTagGetGPIOConfigResponse);  

BCM2838 mailbox tag set GPIO config request

TBCM2838MailboxTagSetGPIOConfigRequest = record

Set GPIO Config
GPIO:LongWord;  
Direction:LongWord;  
Polarity:LongWord;  
Terminator:LongWord;  
PullUp:LongWord;  
State:LongWord;  

BCM2838 mailbox tag set GPIO config response

TBCM2838MailboxTagSetGPIOConfigResponse = record

GPIO:LongWord;  
Direction:LongWord;  
Polarity:LongWord;  
Terminator:LongWord;  
PullUp:LongWord;  
State:LongWord;  

BCM2838 mailbox tag set GPIO config

PBCM2838MailboxTagSetGPIOConfig = ^TBCM2838MailboxTagSetGPIOConfig;

TBCM2838MailboxTagSetGPIOConfig = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetGPIOConfigRequest);  
1:(Response:TBCM2838MailboxTagSetGPIOConfigResponse);  

BCM2838 mailbox tag get throttled request

TBCM2838MailboxTagGetThrottledRequest = record

Get Throttled
Value:LongWord;  

BCM2838 mailbox tag get throttled response

TBCM2838MailboxTagGetThrottledResponse = record

Value:LongWord;  

BCM2838 mailbox tag get throttled

PBCM2838MailboxTagGetThrottled = ^TBCM2838MailboxTagGetThrottled;

TBCM2838MailboxTagGetThrottled = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetThrottledRequest);  
1:(Response:TBCM2838MailboxTagGetThrottledResponse);  

BCM2838 mailbox tag allocate buffer request

TBCM2838MailboxTagAllocateBufferRequest = record

Allocate Buffer
Alignment:LongWord; Bytes

BCM2838 mailbox tag allocate buffer response

TBCM2838MailboxTagAllocateBufferResponse = record

Address:LongWord; Base Address in Bytes
Size:LongWord; Size in Bytes

BCM2838 mailbox tag allocate buffer

PBCM2838MailboxTagAllocateBuffer = ^TBCM2838MailboxTagAllocateBuffer;

TBCM2838MailboxTagAllocateBuffer = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagAllocateBufferRequest);  
1:(Response:TBCM2838MailboxTagAllocateBufferResponse);  

BCM2838 mailbox tag release buffer

PBCM2838MailboxTagReleaseBuffer = ^TBCM2838MailboxTagReleaseBuffer;

TBCM2838MailboxTagReleaseBuffer = record

Release Buffer
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagNoResponse);  

BCM2838 mailbox tag blank screen request

TBCM2838MailboxTagBlankScreenRequest = record

Blank Screen
State:LongWord;  

BCM2838 mailbox tag blank screen response

TBCM2838MailboxTagBlankScreenResponse = record

State:LongWord;  

BCM2838 mailbox tag blank screen

PBCM2838MailboxTagBlankScreen = ^TBCM2838MailboxTagBlankScreen;

TBCM2838MailboxTagBlankScreen = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagBlankScreenRequest);  
1:(Response:TBCM2838MailboxTagBlankScreenResponse);  

BCM2838 mailbox tag physical request

TBCM2838MailboxTagPhysicalRequest = record

Get Physical
Width:LongWord; Pixels
Height:Longword; Pixels

BCM2838 mailbox tag physical response

TBCM2838MailboxTagPhysicalResponse = record

Width:LongWord; Pixels
Height:Longword; Pixels

BCM2838 mailbox tag get physical

PBCM2838MailboxTagGetPhysical = ^TBCM2838MailboxTagGetPhysical;

TBCM2838MailboxTagGetPhysical = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagPhysicalResponse);  

BCM2838 mailbox tag test physical

PBCM2838MailboxTagTestPhysical = ^TBCM2838MailboxTagTestPhysical;

TBCM2838MailboxTagTestPhysical = record

Test Physical
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPhysicalRequest);  
1:(Response:TBCM2838MailboxTagPhysicalResponse);  

BCM2838 mailbox tag set physical

PBCM2838MailboxTagSetPhysical = ^TBCM2838MailboxTagSetPhysical;

TBCM2838MailboxTagSetPhysical = record

Set Physical
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPhysicalRequest);  
1:(Response:TBCM2838MailboxTagPhysicalResponse);  

BCM2838 mailbox tag virtual request

TBCM2838MailboxTagVirtualRequest = record

Get Virtual
Width:LongWord; Pixels
Height:Longword; Pixels

BCM2838 mailbox tag virtual response

TBCM2838MailboxTagVirtualResponse = record

Width:LongWord; Pixels
Height:Longword; Pixels

BCM2838 mailbox tag get virtual

PBCM2838MailboxTagGetVirtual = ^TBCM2838MailboxTagGetVirtual;

TBCM2838MailboxTagGetVirtual = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagVirtualResponse);  

BCM2838 mailbox tag test virtual

PBCM2838MailboxTagTestVirtual = ^TBCM2838MailboxTagTestVirtual;

TBCM2838MailboxTagTestVirtual = record

Test Virtual
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagVirtualRequest);  
1:(Response:TBCM2838MailboxTagVirtualResponse);  

BCM2838 mailbox tag set virtual

PBCM2838MailboxTagSetVirtual = ^TBCM2838MailboxTagSetVirtual;

TBCM2838MailboxTagSetVirtual = record

Set Virtual
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagVirtualRequest);  
1:(Response:TBCM2838MailboxTagVirtualResponse);  

BCM2838 mailbox tag depth request

TBCM2838MailboxTagDepthRequest = record

Get Depth
Depth:LongWord; Bits per pixel

BCM2838 mailbox tag depth response

TBCM2838MailboxTagDepthResponse = record

Depth:LongWord; Bits per pixel

BCM2838 mailbox tag get depth

PBCM2838MailboxTagGetDepth = ^TBCM2838MailboxTagGetDepth;

TBCM2838MailboxTagGetDepth = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagDepthResponse);  

BCM2838 mailbox tag test depth

PBCM2838MailboxTagTestDepth = ^TBCM2838MailboxTagTestDepth;

TBCM2838MailboxTagTestDepth = record

Test Depth
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagDepthRequest);  
1:(Response:TBCM2838MailboxTagDepthResponse);  

BCM2838 mailbox tag set depth

PBCM2838MailboxTagSetDepth = ^TBCM2838MailboxTagSetDepth;

TBCM2838MailboxTagSetDepth = record

Set Depth
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagDepthRequest);  
1:(Response:TBCM2838MailboxTagDepthResponse);  

BCM2838 mailbox tag pixel order request

TBCM2838MailboxTagPixelOrderRequest = record

Get Pixel Order
Order:LongWord;  

BCM2838 mailbox tag pixel order response

TBCM2838MailboxTagPixelOrderResponse = record

Order:LongWord;  

BCM2838 mailbox tag get pixel order

PBCM2838MailboxTagGetPixelOrder = ^TBCM2838MailboxTagGetPixelOrder;

TBCM2838MailboxTagGetPixelOrder = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagPixelOrderResponse);  

BCM2838 mailbox tag test pixel order

PBCM2838MailboxTagTestPixelOrder = ^TBCM2838MailboxTagTestPixelOrder;

TBCM2838MailboxTagTestPixelOrder = record

Test Pixel Order
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPixelOrderRequest);  
1:(Response:TBCM2838MailboxTagPixelOrderResponse);  

BCM2838 mailbox tag set pixel order

PBCM2838MailboxTagSetPixelOrder = ^TBCM2838MailboxTagSetPixelOrder;

TBCM2838MailboxTagSetPixelOrder = record

Set Pixel Order
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPixelOrderRequest);  
1:(Response:TBCM2838MailboxTagPixelOrderResponse);  

BCM2838 mailbox tag alpha mode request

TBCM2838MailboxTagAlphaModeRequest = record

Get Alpha Mode
Mode:LongWord;  

BCM2838 mailbox tag alpha mode response

TBCM2838MailboxTagAlphaModeResponse = record

Mode:LongWord;  

BCM2838 mailbox tag get alpha mode

PBCM2838MailboxTagGetAlphaMode = ^TBCM2838MailboxTagGetAlphaMode;

TBCM2838MailboxTagGetAlphaMode = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagAlphaModeResponse);  

BCM2838 mailbox tag test alpha mode

PBCM2838MailboxTagTestAlphaMode = ^TBCM2838MailboxTagTestAlphaMode;

TBCM2838MailboxTagTestAlphaMode = record

Test Alpha Mode
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagAlphaModeRequest);  
1:(Response:TBCM2838MailboxTagAlphaModeResponse);  

BCM2838 mailbox tag set alpha mode

PBCM2838MailboxTagSetAlphaMode = ^TBCM2838MailboxTagSetAlphaMode;

TBCM2838MailboxTagSetAlphaMode = record

Set Alpha Mode
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagAlphaModeRequest);  
1:(Response:TBCM2838MailboxTagAlphaModeResponse);  

BCM2838 mailbox tag pitch response

TBCM2838MailboxTagPitchResponse = record

Get Pitch
Pitch:LongWord; Bytes per line

BCM2838 mailbox tag get pitch

PBCM2838MailboxTagGetPitch = ^TBCM2838MailboxTagGetPitch;

TBCM2838MailboxTagGetPitch = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagPitchResponse);  

BCM2838 mailbox tag virtual offset request

TBCM2838MailboxTagVirtualOffsetRequest = record

Get Virtual Offset
X:LongWord; Pixels
Y:LongWord; Pixels

BCM2838 mailbox tag virtual offset response

TBCM2838MailboxTagVirtualOffsetResponse = record

X:LongWord; Pixels
Y:LongWord; Pixels

BCM2838 mailbox tag get virtual offset

PBCM2838MailboxTagGetVirtualOffset = ^TBCM2838MailboxTagGetVirtualOffset;

TBCM2838MailboxTagGetVirtualOffset = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);  

BCM2838 mailbox tag test virtual offset

PBCM2838MailboxTagTestVirtualOffset = ^TBCM2838MailboxTagTestVirtualOffset;

TBCM2838MailboxTagTestVirtualOffset = record

Test Virtual Offset
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagVirtualOffsetRequest);  
1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);  

BCM2838 mailbox tag set virtual offset

PBCM2838MailboxTagSetVirtualOffset = ^TBCM2838MailboxTagSetVirtualOffset;

TBCM2838MailboxTagSetVirtualOffset = record

Set Virtual Offset
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagVirtualOffsetRequest);  
1:(Response:TBCM2838MailboxTagVirtualOffsetResponse);  

BCM2838 mailbox tag overscan request

TBCM2838MailboxTagOverscanRequest = record

Get Overscan
Top:LongWord; Pixels
Bottom:LongWord; Pixels
Left:LongWord; Pixels
Right:LongWord; Pixels

BCM2838 mailbox tag overscan response

TBCM2838MailboxTagOverscanResponse = record

Top:LongWord; Pixels
Bottom:LongWord; Pixels
Left:LongWord; Pixels
Right:LongWord; Pixels

BCM2838 mailbox tag get overscan

PBCM2838MailboxTagGetOverscan = ^TBCM2838MailboxTagGetOverscan;

TBCM2838MailboxTagGetOverscan = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagOverscanResponse);  

BCM2838 mailbox tag test overscan

PBCM2838MailboxTagTestOverscan = ^TBCM2838MailboxTagTestOverscan;

TBCM2838MailboxTagTestOverscan = record

Test Overscan
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagOverscanRequest);  
1:(Response:TBCM2838MailboxTagOverscanResponse);  

BCM2838 mailbox tag set overscan

PBCM2838MailboxTagSetOverscan = ^TBCM2838MailboxTagSetOverscan;

TBCM2838MailboxTagSetOverscan = record

Set Overscan
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagOverscanRequest);  
1:(Response:TBCM2838MailboxTagOverscanResponse);  

BCM2838 mailbox tag get palette response

TBCM2838MailboxTagGetPaletteResponse = record

Get Palette
Values:array[0..255] of LongWord; RGBA Palette Values

BCM2838 mailbox tag get palette

PBCM2838MailboxTagGetPalette = ^TBCM2838MailboxTagGetPalette;

TBCM2838MailboxTagGetPalette = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagGetPaletteResponse);  

BCM2838 mailbox tag palette request

TBCM2838MailboxTagPaletteRequest = record

Test Palette
Offset:LongWord; First palette index to set (0-255)
Length:LongWord; Number of palette entries to set (1-256)
Values:array[0..255] of LongWord; RGBA Palette Values

BCM2838 mailbox tag palette response

TBCM2838MailboxTagPaletteResponse = record

Status:LongWord;  

BCM2838 mailbox tag test palette

PBCM2838MailboxTagTestPalette = ^TBCM2838MailboxTagTestPalette;

TBCM2838MailboxTagTestPalette = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPaletteRequest);  
1:(Response:TBCM2838MailboxTagPaletteResponse);  

BCM2838 mailbox tag set palette

PBCM2838MailboxTagSetPalette = ^TBCM2838MailboxTagSetPalette;

TBCM2838MailboxTagSetPalette = record

Set Palette
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagPaletteRequest);  
1:(Response:TBCM2838MailboxTagPaletteResponse);  

BCM2838 mailbox tag get touch response

TBCM2838MailboxTagGetTouchResponse = record

Get Touch Buffer
Address:LongWord;  

BCM2838 mailbox tag get touch

PBCM2838MailboxTagGetTouch = ^TBCM2838MailboxTagGetTouch;

TBCM2838MailboxTagGetTouch = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagGetTouchResponse);  

BCM2838 mailbox tag set touch request

TBCM2838MailboxTagSetTouchRequest = record

Set Touch Buffer
Address:LongWord;  

BCM2838 mailbox tag set touch response

TBCM2838MailboxTagSetTouchResponse = record

Status:LongWord;  

BCM2838 mailbox tag set touch

PBCM2838MailboxTagSetTouch = ^TBCM2838MailboxTagSetTouch;

TBCM2838MailboxTagSetTouch = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetTouchRequest);  
1:(Response:TBCM2838MailboxTagSetTouchResponse);  

BCM2838 mailbox tag get virtual GPIO response

TBCM2838MailboxTagGetVirtualGPIOResponse = record

Get Virtual GPIO Buffer
Address:LongWord;  

BCM2838 mailbox tag get virtual GPIO

PBCM2838MailboxTagGetVirtualGPIO = ^TBCM2838MailboxTagGetVirtualGPIO;

TBCM2838MailboxTagGetVirtualGPIO = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagGetVirtualGPIOResponse);  

BCM2838 mailbox tag set virtual GPIO request

TBCM2838MailboxTagSetVirtualGPIORequest = record

Set Virtual GPIO Buffer
Address:LongWord;  

BCM2838 mailbox tag set virtual GPIO response

TBCM2876MailboxTagSetVirtualGPIOResponse = record

Status:LongWord;  

BCM2838 mailbox tag set virtual GPIO

PBCM2838MailboxTagSetVirtualGPIO = ^TBCM2838MailboxTagSetVirtualGPIO;

TBCM2838MailboxTagSetVirtualGPIO = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetVirtualGPIORequest);  
1:(Response:TBCM2876MailboxTagSetVirtualGPIOResponse);  

BCM2838 mailbox tag test vsync

PBCM2838MailboxTagTestVsync = ^TBCM2838MailboxTagTestVsync;

TBCM2838MailboxTagTestVsync = record

Test Vsync
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagNoResponse);  

BCM2838 mailbox tag set vsync

PBCM2838MailboxTagSetVsync = ^TBCM2838MailboxTagSetVsync;

TBCM2838MailboxTagSetVsync = record

Set Vsync
Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagNoResponse);  

BCM2838 mailbox tag set backlight request

TBCM2838MailboxTagSetBacklightRequest = record

Set Backlight
Brightness:LongWord;  

BCM2838 mailbox tag set backlight response

TBCM2838MailboxTagSetBacklightResponse = record

Brightness:LongWord;  

BCM2838 mailbox tag set backlight

PBCM2838MailboxTagSetBacklight = ^TBCM2838MailboxTagSetBacklight;

TBCM2838MailboxTagSetBacklight = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetBacklightRequest);  
1:(Response:TBCM2838MailboxTagSetBacklightResponse);  

BCM2838 mailbox tag get display id request

TBCM2838MailboxTagGetDisplayIdRequest = record

Get Display Id
DisplayNum:LongWord;  

BCM2838 mailbox tag get display id response

TBCM2838MailboxTagGetDisplayIdResponse = record

DisplayId:LongWord;  

BCM2838 mailbox tag get display id

PBCM2838MailboxTagGetDisplayId = ^TBCM2838MailboxTagGetDisplayId;

TBCM2838MailboxTagGetDisplayId = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetDisplayIdRequest);  
1:(Response:TBCM2838MailboxTagGetDisplayIdResponse);  

BCM2838 mailbox tag set display number request

TBCM2838MailboxTagSetDisplayNumRequest = record

Set Display Num
DisplayNum:LongWord;  

BCM2838 mailbox tag set display number response

TBCM2838MailboxTagSetDisplayNumResponse = record

DisplayNum:LongWord;  

BCM2838 mailbox tag set display number

PBCM2838MailboxTagSetDisplayNum = ^TBCM2838MailboxTagSetDisplayNum;

TBCM2838MailboxTagSetDisplayNum = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetDisplayNumRequest);  
1:(Response:TBCM2838MailboxTagSetDisplayNumResponse);  

BCM2838 mailbox tag get number displays request

TBCM2838MailboxTagGetNumDisplaysRequest = record

Get Num Displays
NumDisplays:LongWord;  

BCM2838 mailbox tag get number displays response

TBCM2838MailboxTagGetNumDisplaysResponse = record

NumDisplays:LongWord;  

BCM2838 mailbox tag get number displays

PBCM2838MailboxTagGetNumDisplays = ^TBCM2838MailboxTagGetNumDisplays;

TBCM2838MailboxTagGetNumDisplays = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetNumDisplaysRequest);  
1:(Response:TBCM2838MailboxTagGetNumDisplaysResponse);  

BCM2838 mailbox tag get display settings request

TBCM2838MailboxTagGetDisplaySettingsRequest = record

Get Display Settings
DisplayNum:LongWord;  
Width:LongWord;  
Height:LongWord;  
Depth:LongWord;  
Pitch:LongWord;  
VirtualWidth:LongWord;  
VirtualHeight:LongWord;  
VirtualWidthOffset:LongWord;  
VirtualHeightOffset:LongWord;  
BusAddress:LongWord;  

BCM2838 mailbox tag get display settings response

TBCM2838MailboxTagGetDisplaySettingsResponse = record

DisplayNum:LongWord;  
Width:LongWord;  
Height:LongWord;  
Depth:LongWord;  
Pitch:LongWord;  
VirtualWidth:LongWord;  
VirtualHeight:LongWord;  
VirtualWidthOffset:LongWord;  
VirtualHeightOffset:LongWord;  
BusAddress:LongWord;  

BCM2838 mailbox tag get display settings

PBCM2838MailboxTagGetDisplaySettings = ^TBCM2838MailboxTagGetDisplaySettings;

TBCM2838MailboxTagGetDisplaySettings = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagGetDisplaySettingsRequest);  
1:(Response:TBCM2838MailboxTagGetDisplaySettingsResponse);  

BCM2838 mailbox tag set cursor info request

TBCM2838MailboxTagSetCursorInfoRequest = record

Set Cursor Info
Width:LongWord; Pixels
Height:LongWord; Pixels
Reserved:LongWord;  
Pixels:Pointer; Format is 32bpp (ARGB) (Width and Height should be >= 16 and (Width * Height) <= 64)
HotspotX:LongWord;  
HotspotY:LongWord;  

BCM2838 mailbox tag cursor response

TBCM2838MailboxTagCursorResponse = record

Status:LongWord;  

BCM2838 mailbox tag set cursor info

PBCM2838MailboxTagSetCursorInfo = ^TBCM2838MailboxTagSetCursorInfo;

TBCM2838MailboxTagSetCursorInfo = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetCursorInfoRequest);  
1:(Response:TBCM2838MailboxTagCursorResponse);  

BCM2838 mailbox tag set cursor state request

TBCM2838MailboxTagSetCursorStateRequest = record

Set Cursor State
Enable:LongWord;  
X:LongWord; Pixels
Y:LongWord; Pixels
Flags:LongWord;  

BCM2838 mailbox tag set cursor state

PBCM2838MailboxTagSetCursorState = ^TBCM2838MailboxTagSetCursorState;

TBCM2838MailboxTagSetCursorState = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagSetCursorStateRequest);  
1:(Response:TBCM2838MailboxTagCursorResponse);  

BCM2838 mailbox tag VCHIQ init request

TBCM2838MailboxTagVCHIQInitRequest = record

VCHIQ Init
Address:LongWord;  

BCM2838 mailbox tag VCHIQ init response

TBCM2838MailboxTagVCHIQInitResponse = record

Status:LongWord; 0 is Success

BCM2838 mailbox tag VCHIQ init

PBCM2838MailboxTagVCHIQInit = ^TBCM2838MailboxTagVCHIQInit;

TBCM2838MailboxTagVCHIQInit = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagVCHIQInitRequest);  
1:(Response:TBCM2838MailboxTagVCHIQInitResponse);  

BCM2838 mailbox tag command line response

TBCM2838MailboxTagCommandLineResponse = record

Get Command Line
CommandLine:array[0..1023] of Char;  

BCM2838 mailbox tag get command line

PBCM2838MailboxTagGetCommandLine = ^TBCM2838MailboxTagGetCommandLine;

TBCM2838MailboxTagGetCommandLine = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagCommandLineResponse);  

BCM2838 mailbox tag DMA channels response

TBCM2838MailboxTagDMAChannelsResponse = record

Get DMA Channels
Channels:LongWord;  

BCM2838 mailbox tag get DMA channels

PBCM2838MailboxTagGetDMAChannels = ^TBCM2838MailboxTagGetDMAChannels;

TBCM2838MailboxTagGetDMAChannels = record

Header:TBCM2838MailboxTagHeader;  
case Integer of  
0:(Request:TBCM2838MailboxTagNoRequest);  
1:(Response:TBCM2838MailboxTagDMAChannelsResponse);  

BCM2838 mailbox tag create buffer

PBCM2838MailboxTagCreateBuffer = ^TBCM2838MailboxTagCreateBuffer;

TBCM2838MailboxTagCreateBuffer = record

Note: A combination tag to allocate and configure a framebuffer in one request
Create Buffer
Physical:TBCM2838MailboxTagSetPhysical;  
Vertual:TBCM2838MailboxTagSetVirtual;  
Depth:TBCM2838MailboxTagSetDepth;  
Order:TBCM2838MailboxTagSetPixelOrder;  
Mode:TBCM2838MailboxTagSetAlphaMode;  
Offset:TBCM2838MailboxTagSetVirtualOffset;  
Overscan:TBCM2838MailboxTagSetOverscan;  
Allocate:TBCM2838MailboxTagAllocateBuffer;  
Pitch:TBCM2838MailboxTagGetPitch;  

BCM2838 mailbox tag query buffer

PBCM2838MailboxTagQueryBuffer = ^TBCM2838MailboxTagQueryBuffer;

TBCM2838MailboxTagQueryBuffer = record

Note: A combination tag to query all framebuffer properties in one request
Query Buffer
Physical:TBCM2838MailboxTagGetPhysical;  
Vertual:TBCM2838MailboxTagGetVirtual;  
Depth:TBCM2838MailboxTagGetDepth;  
Order:TBCM2838MailboxTagGetPixelOrder;  
Mode:TBCM2838MailboxTagGetAlphaMode;  
Offset:TBCM2838MailboxTagGetVirtualOffset;  
Overscan:TBCM2838MailboxTagGetOverscan;  
Pitch:TBCM2838MailboxTagGetPitch;  

BCM2838 ARM local mailbox write registers

PBCM2838ARMLocalMailboxWriteRegisters = ^TBCM2838ARMLocalMailboxWriteRegisters;

TBCM2838ARMLocalMailboxWriteRegisters = record

Note: BCM2838 ARM local structures (See: BCM2711 ARM Peripherals)
Mailbox0Write:LongWord; Mailbox 0 write-set (WO)
Mailbox1Write:LongWord; Mailbox 1 write-set (WO)
Mailbox2Write:LongWord; Mailbox 2 write-set (WO)
Mailbox3Write:LongWord; Mailbox 3 write-set (WO)

BCM2838 ARM local mailbox read clear registers

PBCM2838ARMLocalMailboxReadClearRegisters = ^TBCM2838ARMLocalMailboxReadClearRegisters;

TBCM2838ARMLocalMailboxReadClearRegisters = record

Mailbox0ReadClear:LongWord; Mailbox 0 read & write-high-to-clear
Mailbox1ReadClear:LongWord; Mailbox 1 read & write-high-to-clear
Mailbox2ReadClear:LongWord; Mailbox 2 read & write-high-to-clear
Mailbox3ReadClear:LongWord; Mailbox 3 read & write-high-to-clear

BCM2838 ARM local registers

PBCM2838ARMLocalRegisters = ^TBCM2838ARMLocalRegisters;

TBCM2838ARMLocalRegisters = record

Control:LongWord; Control register $0000
Reserved1:LongWord; Unused $0004
CoreTimerPrescaler:LongWord; Core timer prescaler $0008
CoreInterruptRouting:LongWord; Core Interrupts routing $000C
PMInterruptRoutingSet:LongWord; Performance Monitor Interrupts routing-set $0010
PMInterruptRoutingClear:LongWord; Performance Monitor Interrupts routing-clear $0014
Reserved2:LongWord; Unused $0018
CoreTimerLow:LongWord; Core timer access LS 32 bits $001C
CoreTimerHigh:LongWord; Core timer access MS 32 bits $0020
PeripheralIntRouting0:LongWord; Peripheral Interrupts 0-7 routing (1 to 7 Unused) $0024
PeripheralIntRouting1:LongWord; Peripheral Interrupts 8-15 routing (Unused) $0028
AXIOutstandingCount:LongWord; AXI outstanding counters $002C
AXIOutstandingIRQ:LongWord; AXI outstanding IRQ $0030
LocalTimerControl:LongWord; Local timer control & status $0034
LocalTimerClearReload:LongWord; Local timer IRQ clear & reload $0038
Reserved3:LongWord; Unused $003C
TimersIntControl:array[0..BCM2838_CPU_COUNT - 1] of LongWord; Core0-3 Timers Interrupt control $0040-004C
MailboxIntControl:array[0..BCM2838_CPU_COUNT - 1] of LongWord; Core0-3 Mailboxes Interrupt control $0050-005C
IRQSource:array[0..BCM2838_CPU_COUNT - 1] of LongWord; Core0-3 IRQ Source $0060-006C
FIQSource:array[0..BCM2838_CPU_COUNT - 1] of LongWord; Core0-3 FIQ Source $0070-007C
MailboxWrite:array[0..BCM2838_CPU_COUNT - 1] of TBCM2838ARMLocalMailboxWriteRegisters; Core0-3 Mailbox 0-3 write-set (WO) $0080-00BC
MailboxReadClear:array[0..BCM2838_CPU_COUNT - 1] of TBCM2838ARMLocalMailboxReadClearRegisters; Core0-3 Mailbox 0-3 read & write-high-to-clear $00C0-00FC

BCM2838 virtual GPIO buffer

PBCM2838VirtualGPIOBuffer = ^TBCM2838VirtualGPIOBuffer;

TBCM2838VirtualGPIOBuffer = record

Buffer:Pointer;  
Address:PtrUInt;  
CachedBuffer:LongBool;  
EnableDisable:array[0..BCM2838_VIRTUAL_GPIO_PIN_COUNT - 1] of LongWord; Two packed 16-bit counts of enabled and disabled / Allows host to detect a brief enable that was missed


Public variables


None defined

Function declarations


None defined


Return to Unit Reference