Unit WiFi

Return to Unit Reference

`WLAN_STATUS_SUCCESS = 0;`
`WLAN_STATUS_UNSPECIFIED_FAILURE = 1;`
`WLAN_STATUS_CAPS_UNSUPPORTED = 10;`
`WLAN_STATUS_REASSOC_NO_ASSOC = 11;`
`WLAN_STATUS_ASSOC_DENIED_UNSPEC = 12;`
`WLAN_STATUS_NOT_SUPPORTED_AUTH_ALG = 13;`
`WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION = 14;`
`WLAN_STATUS_CHALLENGE_FAIL = 15;`
`WLAN_STATUS_AUTH_TIMEOUT = 16;`
`WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA = 17;`
`WLAN_STATUS_ASSOC_DENIED_RATES = 18;`
802.11b
`WLAN_STATUS_ASSOC_DENIED_NOSHORTPREAMBLE = 19;`
`WLAN_STATUS_ASSOC_DENIED_NOPBCC = 20;`
`WLAN_STATUS_ASSOC_DENIED_NOAGILITY = 21;`
802.11h
`WLAN_STATUS_ASSOC_DENIED_NOSPECTRUM = 22;`
`WLAN_STATUS_ASSOC_REJECTED_BAD_POWER = 23;`
`WLAN_STATUS_ASSOC_REJECTED_BAD_SUPP_CHAN = 24;`
802.11g
`WLAN_STATUS_ASSOC_DENIED_NOSHORTTIME = 25;`
`WLAN_STATUS_ASSOC_DENIED_NODSSSOFDM = 26;`
802.11w
`WLAN_STATUS_ASSOC_REJECTED_TEMPORARILY = 30;`
`WLAN_STATUS_ROBUST_MGMT_FRAME_POLICY_VIOLATION = 31;`
802.11i
`WLAN_STATUS_INVALID_IE = 40;`
`WLAN_STATUS_INVALID_GROUP_CIPHER = 41;`
`WLAN_STATUS_INVALID_PAIRWISE_CIPHER = 42;`
`WLAN_STATUS_INVALID_AKMP = 43;`
`WLAN_STATUS_UNSUPP_RSN_VERSION = 44;`
`WLAN_STATUS_INVALID_RSN_IE_CAP = 45;`
`WLAN_STATUS_CIPHER_SUITE_REJECTED = 46;`
802.11e
`WLAN_STATUS_UNSPECIFIED_QOS = 32;`
`WLAN_STATUS_ASSOC_DENIED_NOBANDWIDTH = 33;`
`WLAN_STATUS_ASSOC_DENIED_LOWACK = 34;`
`WLAN_STATUS_ASSOC_DENIED_UNSUPP_QOS = 35;`
`WLAN_STATUS_REQUEST_DECLINED = 37;`
`WLAN_STATUS_INVALID_QOS_PARAM = 38;`
`WLAN_STATUS_CHANGE_TSPEC = 39;`
`WLAN_STATUS_WAIT_TS_DELAY = 47;`
`WLAN_STATUS_NO_DIRECT_LINK = 48;`
`WLAN_STATUS_STA_NOT_PRESENT = 49;`
`WLAN_STATUS_STA_NOT_QSTA = 50;`
802.11s
`WLAN_STATUS_ANTI_CLOG_REQUIRED = 76;`
`WLAN_STATUS_FCG_NOT_SUPP = 78;`
`WLAN_STATUS_STA_NO_TBTT = 78;`
802.11ad
`WLAN_STATUS_REJECTED_WITH_SUGGESTED_CHANGES = 39;`
`WLAN_STATUS_REJECTED_FOR_DELAY_PERIOD = 47;`
`WLAN_STATUS_REJECT_WITH_SCHEDULE = 83;`
`WLAN_STATUS_PENDING_ADMITTING_FST_SESSION = 86;`
`WLAN_STATUS_PERFORMING_FST_NOW = 87;`
`WLAN_STATUS_PENDING_GAP_IN_BA_WINDOW = 88;`
`WLAN_STATUS_REJECT_U_PID_SETTING = 89;`
`WLAN_STATUS_REJECT_DSE_BAND = 96;`
`WLAN_STATUS_DENIED_WITH_SUGGESTED_BAND_AND_CHANNEL = 99;`
`WLAN_STATUS_DENIED_DUE_TO_SPECTRUM_MANAGEMENT = 103;`

[Expand]

WLAN reason codes WLAN_REASON_*

`WLAN_REASON_UNSPECIFIED = 1;`
`WLAN_REASON_PREV_AUTH_NOT_VALID = 2;`
`WLAN_REASON_DEAUTH_LEAVING = 3;`
`WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY = 4;`
`WLAN_REASON_DISASSOC_AP_BUSY = 5;`
`WLAN_REASON_CLASS2_FRAME_FROM_NONAUTH_STA = 6;`
`WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA = 7;`
`WLAN_REASON_DISASSOC_STA_HAS_LEFT = 8;`
`WLAN_REASON_STA_REQ_ASSOC_WITHOUT_AUTH = 9;`
802.11h
`WLAN_REASON_DISASSOC_BAD_POWER = 10;`
`WLAN_REASON_DISASSOC_BAD_SUPP_CHAN = 11;`
802.11i
`WLAN_REASON_INVALID_IE = 13;`
`WLAN_REASON_MIC_FAILURE = 14;`
`WLAN_REASON_4WAY_HANDSHAKE_TIMEOUT = 15;`
`WLAN_REASON_GROUP_KEY_HANDSHAKE_TIMEOUT = 16;`
`WLAN_REASON_IE_DIFFERENT = 17;`
`WLAN_REASON_INVALID_GROUP_CIPHER = 18;`
`WLAN_REASON_INVALID_PAIRWISE_CIPHER = 19;`
`WLAN_REASON_INVALID_AKMP = 20;`
`WLAN_REASON_UNSUPP_RSN_VERSION = 21;`
`WLAN_REASON_INVALID_RSN_IE_CAP = 22;`
`WLAN_REASON_IEEE8021X_FAILED = 23;`
`WLAN_REASON_CIPHER_SUITE_REJECTED = 24;`
TDLS (802.11z)
`WLAN_REASON_TDLS_TEARDOWN_UNREACHABLE = 25;`
`WLAN_REASON_TDLS_TEARDOWN_UNSPECIFIED = 26;`
802.11e
`WLAN_REASON_DISASSOC_UNSPECIFIED_QOS = 32;`
`WLAN_REASON_DISASSOC_QAP_NO_BANDWIDTH = 33;`
`WLAN_REASON_DISASSOC_LOW_ACK = 34;`
`WLAN_REASON_DISASSOC_QAP_EXCEED_TXOP = 35;`
`WLAN_REASON_QSTA_LEAVE_QBSS = 36;`
`WLAN_REASON_QSTA_NOT_USE = 37;`
`WLAN_REASON_QSTA_REQUIRE_SETUP = 38;`
`WLAN_REASON_QSTA_TIMEOUT = 39;`
`WLAN_REASON_QSTA_CIPHER_NOT_SUPP = 45;`
802.11s
`WLAN_REASON_MESH_PEER_CANCELED = 52;`
`WLAN_REASON_MESH_MAX_PEERS = 53;`
`WLAN_REASON_MESH_CONFIG = 54;`
`WLAN_REASON_MESH_CLOSE = 55;`
`WLAN_REASON_MESH_MAX_RETRIES = 56;`
`WLAN_REASON_MESH_CONFIRM_TIMEOUT = 57;`
`WLAN_REASON_MESH_INVALID_GTK = 58;`
`WLAN_REASON_MESH_INCONSISTENT_PARAM = 59;`
`WLAN_REASON_MESH_INVALID_SECURITY = 60;`
`WLAN_REASON_MESH_PATH_ERROR = 61;`
`WLAN_REASON_MESH_PATH_NOFORWARD = 62;`
`WLAN_REASON_MESH_PATH_DEST_UNREACHABLE = 63;`
`WLAN_REASON_MAC_EXISTS_IN_MBSS = 64;`
`WLAN_REASON_MESH_CHAN_REGULATORY = 65;`
`WLAN_REASON_MESH_CHAN = 66;`

[Expand]

WLAN information element Ids WLAN_EID_*

`WLAN_EID_SSID = 0;`
`WLAN_EID_SUPP_RATES = 1;`
`WLAN_EID_FH_PARAMS = 2;`	reserved now
`WLAN_EID_DS_PARAMS = 3;`
`WLAN_EID_CF_PARAMS = 4;`
`WLAN_EID_TIM = 5;`
`WLAN_EID_IBSS_PARAMS = 6;`
`WLAN_EID_COUNTRY = 7;`
8-9 reserved
`WLAN_EID_REQUEST = 10;`
`WLAN_EID_QBSS_LOAD = 11;`
`WLAN_EID_EDCA_PARAM_SET = 12;`
`WLAN_EID_TSPEC = 13;`
`WLAN_EID_TCLAS = 14;`
`WLAN_EID_SCHEDULE = 15;`
`WLAN_EID_CHALLENGE = 16;`
17-31 reserved for challenge text extension
`WLAN_EID_PWR_CONSTRAINT = 32;`
`WLAN_EID_PWR_CAPABILITY = 33;`
`WLAN_EID_TPC_REQUEST = 34;`
`WLAN_EID_TPC_REPORT = 35;`
`WLAN_EID_SUPPORTED_CHANNELS = 36;`
`WLAN_EID_CHANNEL_SWITCH = 37;`
`WLAN_EID_MEASURE_REQUEST = 38;`
`WLAN_EID_MEASURE_REPORT = 39;`
`WLAN_EID_QUIET = 40;`
`WLAN_EID_IBSS_DFS = 41;`
`WLAN_EID_ERP_INFO = 42;`
`WLAN_EID_TS_DELAY = 43;`
`WLAN_EID_TCLAS_PROCESSING = 44;`
`WLAN_EID_HT_CAPABILITY = 45;`
`WLAN_EID_QOS_CAPA = 46;`
47 reserved for Broadcom
`WLAN_EID_RSN = 48;`
`WLAN_EID_802_15_COEX = 49;`
`WLAN_EID_EXT_SUPP_RATES = 50;`
`WLAN_EID_AP_CHAN_REPORT = 51;`
`WLAN_EID_NEIGHBOR_REPORT = 52;`
`WLAN_EID_RCPI = 53;`
`WLAN_EID_MOBILITY_DOMAIN = 54;`
`WLAN_EID_FAST_BSS_TRANSITION = 55;`
`WLAN_EID_TIMEOUT_INTERVAL = 56;`
`WLAN_EID_RIC_DATA = 57;`
`WLAN_EID_DSE_REGISTERED_LOCATION = 58;`
`WLAN_EID_SUPPORTED_REGULATORY_CLASSES = 59;`
`WLAN_EID_EXT_CHANSWITCH_ANN = 60;`
`WLAN_EID_HT_OPERATION = 61;`
`WLAN_EID_SECONDARY_CHANNEL_OFFSET = 62;`
`WLAN_EID_BSS_AVG_ACCESS_DELAY = 63;`
`WLAN_EID_ANTENNA_INFO = 64;`
`WLAN_EID_RSNI = 65;`
`WLAN_EID_MEASUREMENT_PILOT_TX_INFO = 66;`
`WLAN_EID_BSS_AVAILABLE_CAPACITY = 67;`
`WLAN_EID_BSS_AC_ACCESS_DELAY = 68;`
`WLAN_EID_TIME_ADVERTISEMENT = 69;`
`WLAN_EID_RRM_ENABLED_CAPABILITIES = 70;`
`WLAN_EID_MULTIPLE_BSSID = 71;`
`WLAN_EID_BSS_COEX_2040 = 72;`
`WLAN_EID_BSS_INTOLERANT_CHL_REPORT = 73;`
`WLAN_EID_OVERLAP_BSS_SCAN_PARAM = 74;`
`WLAN_EID_RIC_DESCRIPTOR = 75;`
`WLAN_EID_MMIE = 76;`
`WLAN_EID_ASSOC_COMEBACK_TIME = 77;`
`WLAN_EID_EVENT_REQUEST = 78;`
`WLAN_EID_EVENT_REPORT = 79;`
`WLAN_EID_DIAGNOSTIC_REQUEST = 80;`
`WLAN_EID_DIAGNOSTIC_REPORT = 81;`
`WLAN_EID_LOCATION_PARAMS = 82;`
`WLAN_EID_NON_TX_BSSID_CAP = 83;`
`WLAN_EID_SSID_LIST = 84;`
`WLAN_EID_MULTI_BSSID_IDX = 85;`
`WLAN_EID_FMS_DESCRIPTOR = 86;`
`WLAN_EID_FMS_REQUEST = 87;`
`WLAN_EID_FMS_RESPONSE = 88;`
`WLAN_EID_QOS_TRAFFIC_CAPA = 89;`
`WLAN_EID_BSS_MAX_IDLE_PERIOD = 90;`
`WLAN_EID_TSF_REQUEST = 91;`
`WLAN_EID_TSF_RESPOSNE = 92;`
`WLAN_EID_WNM_SLEEP_MODE = 93;`
`WLAN_EID_TIM_BCAST_REQ = 94;`
`WLAN_EID_TIM_BCAST_RESP = 95;`
`WLAN_EID_COLL_IF_REPORT = 96;`
`WLAN_EID_CHANNEL_USAGE = 97;`
`WLAN_EID_TIME_ZONE = 98;`
`WLAN_EID_DMS_REQUEST = 99;`
`WLAN_EID_DMS_RESPONSE = 100;`
`WLAN_EID_LINK_ID = 101;`
`WLAN_EID_WAKEUP_SCHEDUL = 102;`
103 reserved
`WLAN_EID_CHAN_SWITCH_TIMING = 104;`
`WLAN_EID_PTI_CONTROL = 105;`
`WLAN_EID_PU_BUFFER_STATUS = 106;`
`WLAN_EID_INTERWORKING = 107;`
`WLAN_EID_ADVERTISEMENT_PROTOCOL = 108;`
`WLAN_EID_EXPEDITED_BW_REQ = 109;`
`WLAN_EID_QOS_MAP_SET = 110;`
`WLAN_EID_ROAMING_CONSORTIUM = 111;`
`WLAN_EID_EMERGENCY_ALERT = 112;`
`WLAN_EID_MESH_CONFIG = 113;`
`WLAN_EID_MESH_ID = 114;`
`WLAN_EID_LINK_METRIC_REPORT = 115;`
`WLAN_EID_CONGESTION_NOTIFICATION = 116;`
`WLAN_EID_PEER_MGMT = 117;`
`WLAN_EID_CHAN_SWITCH_PARAM = 118;`
`WLAN_EID_MESH_AWAKE_WINDOW = 119;`
`WLAN_EID_BEACON_TIMING = 120;`
`WLAN_EID_MCCAOP_SETUP_REQ = 121;`
`WLAN_EID_MCCAOP_SETUP_RESP = 122;`
`WLAN_EID_MCCAOP_ADVERT = 123;`
`WLAN_EID_MCCAOP_TEARDOWN = 124;`
`WLAN_EID_GANN = 125;`
`WLAN_EID_RANN = 126;`
`WLAN_EID_EXT_CAPABILITY = 127;`
128-129 reserved for Agere
`WLAN_EID_PREQ = 130;`
`WLAN_EID_PREP = 131;`
`WLAN_EID_PERR = 132;`
133-136 reserved for Cisco
`WLAN_EID_PXU = 137;`
`WLAN_EID_PXUC = 138;`
`WLAN_EID_AUTH_MESH_PEER_EXCH = 139;`
`WLAN_EID_MIC = 140;`
`WLAN_EID_DESTINATION_URI = 141;`
`WLAN_EID_UAPSD_COEX = 142;`
`WLAN_EID_WAKEUP_SCHEDULE = 143;`
`WLAN_EID_EXT_SCHEDULE = 144;`
`WLAN_EID_STA_AVAILABILITY = 145;`
`WLAN_EID_DMG_TSPEC = 146;`
`WLAN_EID_DMG_AT = 147;`
`WLAN_EID_DMG_CAP = 148;`
149 reserved for Cisco
`WLAN_EID_CISCO_VENDOR_SPECIFIC = 150;`
`WLAN_EID_DMG_OPERATION = 151;`
`WLAN_EID_DMG_BSS_PARAM_CHANGE = 152;`
`WLAN_EID_DMG_BEAM_REFINEMENT = 153;`
`WLAN_EID_CHANNEL_MEASURE_FEEDBACK = 154;`
155-156 reserved for Cisco
`WLAN_EID_AWAKE_WINDOW = 157;`
`WLAN_EID_MULTI_BAND = 158;`
`WLAN_EID_ADDBA_EXT = 159;`
`WLAN_EID_NEXT_PCP_LIST = 160;`
`WLAN_EID_PCP_HANDOVER = 161;`
`WLAN_EID_DMG_LINK_MARGIN = 162;`
`WLAN_EID_SWITCHING_STREAM = 163;`
`WLAN_EID_SESSION_TRANSITION = 164;`
`WLAN_EID_DYN_TONE_PAIRING_REPORT = 165;`
`WLAN_EID_CLUSTER_REPORT = 166;`
`WLAN_EID_RELAY_CAP = 167;`
`WLAN_EID_RELAY_XFER_PARAM_SET = 168;`
`WLAN_EID_BEAM_LINK_MAINT = 169;`
`WLAN_EID_MULTIPLE_MAC_ADDR = 170;`
`WLAN_EID_U_PID = 171;`
`WLAN_EID_DMG_LINK_ADAPT_ACK = 172;`
173 reserved for Symbol
`WLAN_EID_MCCAOP_ADV_OVERVIEW = 174;`
`WLAN_EID_QUIET_PERIOD_REQ = 175;`
176 reserved for Symbol
`WLAN_EID_QUIET_PERIOD_RESP = 177;`
178-179 reserved for Symbol
180 reserved for ISO/IEC 20011
`WLAN_EID_EPAC_POLICY = 182;`
`WLAN_EID_CLISTER_TIME_OFF = 183;`
`WLAN_EID_INTER_AC_PRIO = 184;`
`WLAN_EID_SCS_DESCRIPTOR = 185;`
`WLAN_EID_QLOAD_REPORT = 186;`
`WLAN_EID_HCCA_TXOP_UPDATE_COUNT = 187;`
`WLAN_EID_HL_STREAM_ID = 188;`
`WLAN_EID_GCR_GROUP_ADDR = 189;`
`WLAN_EID_ANTENNA_SECTOR_ID_PATTERN = 190;`
`WLAN_EID_VHT_CAPABILITY = 191;`
`WLAN_EID_VHT_OPERATION = 192;`
`WLAN_EID_EXTENDED_BSS_LOAD = 193;`
`WLAN_EID_WIDE_BW_CHANNEL_SWITCH = 194;`
`WLAN_EID_VHT_TX_POWER_ENVELOPE = 195;`
`WLAN_EID_CHANNEL_SWITCH_WRAPPER = 196;`
`WLAN_EID_AID = 197;`
`WLAN_EID_QUIET_CHANNEL = 198;`
`WLAN_EID_OPMODE_NOTIF = 199;`

`WLAN_EID_VENDOR_SPECIFIC = 221;`
`WLAN_EID_QOS_PARAMETER = 222;`

[Expand]

WLAN action category codes WLAN_CATEGORY_*

[Expand]

WLAN spectrum action codes WLAN_ACTION_SPCT_*

[Expand]

WLAN HT action codes WLAN_HT_ACTION_*

[Expand]

WLAN VHT action codes WLAN_VHT_ACTION_*

[Expand]

WLAN self protected action codes WLAN_SP_*

[Expand]

WLAN mesh action codes WLAN_MESH_ACTION_*

[Expand]

WLAN security key lengths WLAN_KEY_LEN_*

[Expand]

IEEE 802.11 security key lengths IEEE80211_*_LEN

[Expand]

WLAN public action codes WLAN_PUB_ACTION_*

[Expand]

WLAN TDLS action codes WLAN_TDLS_*

[Expand]

WLAN extended channel switching capabilities 1st byte WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING*

[Expand]

WLAN extended TDLS capabilities 4th byte WLAN_EXT_CAPA4_TDLS_*

[Expand]

WLAN extended interworking capabilities 4th byte WLAN_EXT_CAPA4_INTERWORKING_*

[Expand]

WLAN extended TDLS capabilities 5th byte WLAN_EXT_CAPA5_TDLS_*

[Expand]

WLAN extended TDLS capabilities 8th byte WLAN_EXT_CAPA8_TDLS_*

[Expand]

WLAN TDLS specific payload type WLAN_TDLS_*_RFTYPE*

[Expand]

WLAN coex IE information field bits WLAN_*_COEX_INFORMATION_*

[Expand]

IEEE 802.11 mesh synchronization method identifier IEEE80211_SYNC_METHOD_*

[Expand]

IEEE 802.11 mesh path selection protocol identifier IEEE80211_PATH_PROTOCOL_*

[Expand]

IEEE 802.11 mesh path selection metric identifier IEEE80211_PATH_METRIC_*

[Expand]

IEEE 802.11 root mesh STA mode identifier IEEE80211_ROOTMODE_*

[Expand]

IEEE 802.11 country information element IEEE80211_COUNTRY_*

[Expand]

WLAN timeout interval WLAN_TIMEOUT_*

[Expand]

WLAN block-ack action code WLAN_ACTION_*

[Expand]

WLAN block-ack parties WLAN_BACK_*

[Expand]

WLAN SA query action WLAN_ACTION_SA_QUERY_*

[Expand]

WLAN cipher suite selectors WLAN_CIPHER_SUITE_*

[Expand]

WLAN AKM suite selectors WLAN_AKM_SUITE_*

[Expand]

WLAN key lengths WLAN_*_KEY_LEN*

[Expand]

WLAN OUI types WLAN_OUI_WFA*

[Expand]

IEEE 802.11 Tspec element IEEE80211_WMM_IE_TSPEC_TID_*

[Expand]

IEEE 802.11 Tspec status IEEE80211_TSPEC_STATUS_*

[Expand]

IEEE 802.11 frequency bands IEEE80211_BAND_*

[Expand]

IEEE 802.11 channel flags IEEE80211_CHAN_*

[Expand]

IEEE 802.11 DFS times IEEE80211_DFS_MIN_*_TIME_MS*

[Expand]

IEEE 802.11 rate flags IEEE80211_RATE_*

[Expand]

IEEE 802.11 BSS type values IEEE80211_BSS_TYPE_*

[Expand]

IEEE 802.11 privacy values IEEE80211_PRIVACY_*

[Expand]

IEEE 802.11 filter flags IEEE80211_FIF_*

[Expand]

IEEE 802.11 hardware flags IEEE80211_HW_*

[Expand]

IEEE 802.11 configuration flags IEEE80211_CONF_*

[Expand]

IEEE 802.11 configuration changed flags IEEE80211_CONF_CHANGE_*

[Expand]

IEEE 802.11 TX status headroom IEEE80211_TX_STATUS_HEADROOM_*

[Expand]

IEEE 802.11 max CSA counters IEEE80211_MAX_CSA_COUNTERS_*

[Expand]

WiFi specific constants WIFI_*

[Expand]

WiFi device states WIFI_STATE_*

[Expand]

WiFi device status WIFI_STATUS_*

[Expand]

WiFi device flags WIFI_FLAG_*

[Expand]

WiFi device features WIFI_FEATURE_*

Note: As per Linux nl80211.h NL80211_FEATURE_*
`WIFI_FEATURE_SK_TX_STATUS = (1 shl 0);`	This driver supports reflecting back TX status to the socket error queue when requested with the socket option
`WIFI_FEATURE_HT_IBSS = (1 shl 1);`	This driver supports IBSS with HT datarates
`WIFI_FEATURE_INACTIVITY_TIMER = (1 shl 2);`	This driver takes care of freeing up the connected inactive stations in AP mode
`WIFI_FEATURE_CELL_BASE_REG_HINTS = (1 shl 3);`	This driver has been tested to work properly to support receiving regulatory hints from cellular base stations
`WIFI_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = (1 shl 4);`	No longer available, only here to reserve the value for API/ABI compatibility
`WIFI_FEATURE_SAE = (1 shl 5);`	This driver supports simultaneous authentication of equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station mode
`WIFI_FEATURE_LOW_PRIORITY_SCAN = (1 shl 6);`	This driver supports low priority scan
`WIFI_FEATURE_SCAN_FLUSH = (1 shl 7);`	Scan flush is supported
`WIFI_FEATURE_AP_SCAN = (1 shl 8);`	Support scanning using an AP vif
`WIFI_FEATURE_VIF_TXPOWER = (1 shl 9);`	The driver supports per-vif TX power setting
`WIFI_FEATURE_NEED_OBSS_SCAN = (1 shl 10);`	The driver expects userspace to perform OBSS scans and generate 20/40 BSS coex reports
`WIFI_FEATURE_P2P_GO_CTWIN = (1 shl 11);`	P2P GO implementation supports CT Window setting
`WIFI_FEATURE_P2P_GO_OPPPS = (1 shl 12);`	P2P GO implementation supports opportunistic powersave
bit 13 is reserved
`WIFI_FEATURE_ADVERTISE_CHAN_LIMITS = (1 shl 14);`	cfg80211 advertises channel limits (HT40, VHT 80/160 MHz) if this flag is set
`WIFI_FEATURE_FULL_AP_CLIENT_STATE = (1 shl 15);`	The driver supports full state transitions for AP clients
`WIFI_FEATURE_USERSPACE_MPM = (1 shl 16);`	This driver supports a userspace Mesh Peering Management
`WIFI_FEATURE_ACTIVE_MONITOR = (1 shl 17);`	This driver supports an active monitor interface
`WIFI_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = (1 shl 18);`	This driver supports dynamic channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the lifetime of a BSS
`WIFI_FEATURE_DS_PARAM_SET_IE_IN_PROBES = (1 shl 19);`	This device adds a DS Parameter Set IE to probe requests
`WIFI_FEATURE_WFA_TPC_IE_IN_PROBES = (1 shl 20);`	This device adds a WFA TPC Report IE to probe requests
`WIFI_FEATURE_QUIET = (1 shl 21);`	This device, in client mode, supports Quiet Period requests sent to it by an AP.
`WIFI_FEATURE_TX_POWER_INSERTION = (1 shl 22);`	This device is capable of inserting the current tx power value into the TPC Report IE in the spectrum management TPC Report action frame, and in the Radio Measurement Link Measurement Report action frame.
`WIFI_FEATURE_ACKTO_ESTIMATION = (1 shl 23);`	This driver supports dynamic ACK timeout estimation
`WIFI_FEATURE_STATIC_SMPS = (1 shl 24);`	Device supports static spatial multiplexing powersave
`WIFI_FEATURE_DYNAMIC_SMPS = (1 shl 25);`	Device supports dynamic spatial multiplexing powersave
`WIFI_FEATURE_SUPPORTS_WMM_ADMISSION = (1 shl 26);`	The device supports setting up WMM TSPEC sessions
`WIFI_FEATURE_MAC_ON_CREATE = (1 shl 27);`	Device supports configuring the vif's MAC address upon creation
`WIFI_FEATURE_TDLS_CHANNEL_SWITCH = (1 shl 28);`	Driver supports channel switching when operating as a TDLS peer
`WIFI_FEATURE_SCAN_RANDOM_MAC_ADDR = (1 shl 29);`	This device/driver supports using a random MAC address during scan (if the device is unassociated)
`WIFI_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR = (1 shl 30);`	This device/driver supports using a random MAC address for every scan iteration during scheduled scan (while not associated)
`WIFI_FEATURE_ND_RANDOM_MAC_ADDR = (1 shl 31);`	This device/driver supports using a random MAC address for every scan iteration during "net detect" i.e. scan in unassociated WoWLAN

[Expand]

WiFi device LED values WIFI_LED_*

[Expand]

WiFi interface types WIFI_IFTYPE_*

[Expand]

WiFi channel types WIFI_CHAN_*

[Expand]

WiFi channel widths WIFI_CHAN_WIDTH_*

[Expand]

WiFi signal types WIFI_SIGNAL_TYPE_*

[Expand]

WiFi TX power adjustment WIFI_TX_POWER_*

[Expand]

WiFi RX flags WIFI_RX_FLAG_*

Note: As per Linux mac80211.h RX_FLAG_*
`WIFI_RX_FLAG_MMIC_ERROR = (1 shl 0);`	Michael MIC error was reported on this frame
`WIFI_RX_FLAG_DECRYPTED = (1 shl 1);`	This frame was decrypted in hardware
`WIFI_RX_FLAG_MMIC_STRIPPED = (1 shl 3);`	The Michael MIC is stripped off this frame, verification has been done by the hardware.
`WIFI_RX_FLAG_IV_STRIPPED = (1 shl 4);`	The IV/ICV are stripped from this frame
`WIFI_RX_FLAG_FAILED_FCS_CRC = (1 shl 5);`	Set this flag if the FCS check failed on the frame
`WIFI_RX_FLAG_FAILED_PLCP_CRC = (1 shl 6);`	Set this flag if the PCLP check failed on the frame
`WIFI_RX_FLAG_MACTIME_START = (1 shl 7);`	The timestamp passed in the RX status MACTime field is valid and contains the time the first symbol of the MPDU was received
`WIFI_RX_FLAG_SHORTPRE = (1 shl 8);`	Short preamble was used for this frame
`WIFI_RX_FLAG_HT = (1 shl 9);`	HT MCS was used and RateIndex is MCS index
`WIFI_RX_FLAG_40MHZ = (1 shl 10);`	HT40 (40 MHz) was used
`WIFI_RX_FLAG_SHORT_GI = (1 shl 11);`	Short guard interval was used
`WIFI_RX_FLAG_NO_SIGNAL_VAL = (1 shl 12);`	The signal strength value is not present. Valid only for data frames (mainly A-MPDU).
`WIFI_RX_FLAG_HT_GF = (1 shl 13);`	This frame was received in a HT-greenfield transmission
`WIFI_RX_FLAG_AMPDU_DETAILS = (1 shl 14);`	A-MPDU details are known
`WIFI_RX_FLAG_AMPDU_REPORT_ZEROLEN = (1 shl 15);`	Driver reports 0-length subframes
`WIFI_RX_FLAG_AMPDU_IS_ZEROLEN = (1 shl 16);`	This is a zero-length subframe
`WIFI_RX_FLAG_AMPDU_LAST_KNOWN = (1 shl 17);`	Last subframe is known
`WIFI_RX_FLAG_AMPDU_IS_LAST = (1 shl 18);`	This subframe is the last subframe of the A-MPDU
`WIFI_RX_FLAG_AMPDU_DELIM_CRC_ERROR = (1 shl 19);`	A delimiter CRC error has been detected on this subframe
`WIFI_RX_FLAG_AMPDU_DELIM_CRC_KNOWN = (1 shl 20);`	The delimiter CRC field is known
`WIFI_RX_FLAG_MACTIME_END = (1 shl 21);`	The timestamp passed in the RX status MACTime field is valid and contains the time the last symbol of the MPDU (including FCS) was received
`WIFI_RX_FLAG_VHT = (1 shl 22);`	HT MCS was used and RateIndex is MCS index
`WIFI_RX_FLAG_LDPC = (1 shl 23);`	LDPC was used
`WIFI_RX_FLAG_STBC_MASK = (1 shl 26) or (1 shl 27);`	STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
`WIFI_RX_FLAG_10MHZ = (1 shl 28);`	10 MHz (half channel) was used
`WIFI_RX_FLAG_5MHZ = (1 shl 29);`	5 MHz (quarter channel) was used
`WIFI_RX_FLAG_AMSDU_MORE = (1 shl 30);`	Some drivers may prefer to report separate A-MSDU subframes instead of a one huge frame for performance reasons
`WIFI_RX_FLAG_RADIOTAP_VENDOR_DATA = (1 shl 31);`	This frame contains vendor-specific radiotap data in the data (before the frame)

[Expand]

WiFi RX VHT flags WIFI_RX_VHT_FLAG_*

Type definitions

To be documented

Public variables

To be documented

Function declarations

To be documented

Return to Unit Reference

Note: As per Linux ieee80211.h
`IEEE80211_FCS_LEN = 4;`

`IEEE80211_FCTL_VERS = $0003;`
`IEEE80211_FCTL_FTYPE = $000c;`
`IEEE80211_FCTL_STYPE = $00f0;`
`IEEE80211_FCTL_TODS = $0100;`
`IEEE80211_FCTL_FROMDS = $0200;`
`IEEE80211_FCTL_MOREFRAGS = $0400;`
`IEEE80211_FCTL_RETRY = $0800;`
`IEEE80211_FCTL_PM = $1000;`
`IEEE80211_FCTL_MOREDATA = $2000;`
`IEEE80211_FCTL_PROTECTED = $4000;`
`IEEE80211_FCTL_ORDER = $8000;`
`IEEE80211_FCTL_CTL_EXT = $0f00;`

`IEEE80211_SCTL_FRAG = $000F;`
`IEEE80211_SCTL_SEQ = $FFF0;`

`IEEE80211_FTYPE_MGMT = $0000;`
`IEEE80211_FTYPE_CTL = $0004;`
`IEEE80211_FTYPE_DATA = $0008;`
`IEEE80211_FTYPE_EXT = $000c;`

`IEEE80211_STYPE_ASSOC_REQ = $0000;`
`IEEE80211_STYPE_ASSOC_RESP = $0010;`
`IEEE80211_STYPE_REASSOC_REQ = $0020;`
`IEEE80211_STYPE_REASSOC_RESP = $0030;`
`IEEE80211_STYPE_PROBE_REQ = $0040;`
`IEEE80211_STYPE_PROBE_RESP = $0050;`
`IEEE80211_STYPE_BEACON = $0080;`
`IEEE80211_STYPE_ATIM = $0090;`
`IEEE80211_STYPE_DISASSOC = $00A0;`
`IEEE80211_STYPE_AUTH = $00B0;`
`IEEE80211_STYPE_DEAUTH = $00C0;`
`IEEE80211_STYPE_ACTION = $00D0;`

`IEEE80211_STYPE_CTL_EXT = $0060;`
`IEEE80211_STYPE_BACK_REQ = $0080;`
`IEEE80211_STYPE_BACK = $0090;`
`IEEE80211_STYPE_PSPOLL = $00A0;`
`IEEE80211_STYPE_RTS = $00B0;`
`IEEE80211_STYPE_CTS = $00C0;`
`IEEE80211_STYPE_ACK = $00D0;`
`IEEE80211_STYPE_CFEND = $00E0;`
`IEEE80211_STYPE_CFENDACK = $00F0;`

`IEEE80211_STYPE_DATA = $0000;`
`IEEE80211_STYPE_DATA_CFACK = $0010;`
`IEEE80211_STYPE_DATA_CFPOLL = $0020;`
`IEEE80211_STYPE_DATA_CFACKPOLL = $0030;`
`IEEE80211_STYPE_NULLFUNC = $0040;`
`IEEE80211_STYPE_CFACK = $0050;`
`IEEE80211_STYPE_CFPOLL = $0060;`
`IEEE80211_STYPE_CFACKPOLL = $0070;`
`IEEE80211_STYPE_QOS_DATA = $0080;`
`IEEE80211_STYPE_QOS_DATA_CFACK = $0090;`
`IEEE80211_STYPE_QOS_DATA_CFPOLL = $00A0;`
`IEEE80211_STYPE_QOS_DATA_CFACKPOLL = $00B0;`
`IEEE80211_STYPE_QOS_NULLFUNC = $00C0;`
`IEEE80211_STYPE_QOS_CFACK = $00D0;`
`IEEE80211_STYPE_QOS_CFPOLL = $00E0;`
`IEEE80211_STYPE_QOS_CFACKPOLL = $00F0;`

Note: Control extension - for IEEE80211_FTYPE_CTL \| IEEE80211_STYPE_CTL_EXT
`IEEE80211_CTL_EXT_POLL = $2000;`
`IEEE80211_CTL_EXT_SPR = $3000;`
`IEEE80211_CTL_EXT_GRANT = $4000;`
`IEEE80211_CTL_EXT_DMG_CTS = $5000;`
`IEEE80211_CTL_EXT_DMG_DTS = $6000;`
`IEEE80211_CTL_EXT_SSW = $8000;`
`IEEE80211_CTL_EXT_SSW_FBACK = $9000;`
`IEEE80211_CTL_EXT_SSW_ACK = $a000;`

Unit WiFi

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

Note: Extension added by 802.11ad
`IEEE80211_STYPE_DMG_BEACON = $0000;`

`IEEE80211_MAX_FRAG_THRESHOLD = 2352;`
`IEEE80211_MAX_RTS_THRESHOLD = 2353;`
`IEEE80211_MAX_AID = 2007;`
`IEEE80211_MAX_TIM_LEN = 251;`
`IEEE80211_MAX_MESH_PEERINGS = 63;`
Maximum size for the MA-UNITDATA primitive, 802.11 standard section 6.2.1.1.2. 802.11e clarifies the figure in section 7.1.2. The frame body is up to 2304 octets long (maximum MSDU size) plus any crypt overhead.
`IEEE80211_MAX_DATA_LEN = 2304;`
802.11ad extends maximum MSDU size for DMG (freq > 40Ghz) networks to 7920 bytes, see 8.2.3 General frame format.
`IEEE80211_MAX_DATA_LEN_DMG = 7920;`

30 byte 4 addr hdr, 2 byte QoS, 2304 byte MSDU, 12 byte crypt, 4 byte FCS
`IEEE80211_MAX_FRAME_LEN = 2352;`
`IEEE80211_MAX_SSID_LEN = 32;`
`IEEE80211_MAX_MESH_ID_LEN = 32;`

`IEEE80211_FIRST_TSPEC_TSID = 8;`
`IEEE80211_NUM_TIDS = 16;`

`IEEE80211_MAX_CHAINS = 4;`

Number of user priorities 802.11 uses
`IEEE80211_NUM_UPS = 8;`

`IEEE80211_QOS_CTL_TAG1D_MASK = $0007;`	1d tag mask
`IEEE80211_QOS_CTL_TID_MASK = $000f;`	TID mask
`IEEE80211_QOS_CTL_EOSP = $0010;`	EOSP
`IEEE80211_QOS_CTL_ACK_POLICY_NORMAL = $0000;`	ACK policy
`IEEE80211_QOS_CTL_ACK_POLICY_NOACK = $0020;`
`IEEE80211_QOS_CTL_ACK_POLICY_NO_EXPL = $0040;`
`IEEE80211_QOS_CTL_ACK_POLICY_BLOCKACK = $0060;`
`IEEE80211_QOS_CTL_ACK_POLICY_MASK = $0060;`
`IEEE80211_QOS_CTL_A_MSDU_PRESENT = $0080;`	A-MSDU 802.11n
`IEEE80211_QOS_CTL_MESH_CONTROL_PRESENT = $0100;`	Mesh Control 802.11s
`IEEE80211_QOS_CTL_MESH_PS_LEVEL = $0200;`	Mesh Power Save Level
`IEEE80211_QOS_CTL_RSPI = $0400;`	Mesh Receiver Service Period Initiated

`IEEE80211_WMM_IE_AP_QOSINFO_UAPSD = (1 shl 7);`
`IEEE80211_WMM_IE_AP_QOSINFO_PARAM_SET_CNT_MASK = $0f;`

`IEEE80211_WMM_IE_STA_QOSINFO_AC_VO = (1 shl 0);`
`IEEE80211_WMM_IE_STA_QOSINFO_AC_VI = (1 shl 1);`
`IEEE80211_WMM_IE_STA_QOSINFO_AC_BK = (1 shl 2);`
`IEEE80211_WMM_IE_STA_QOSINFO_AC_BE = (1 shl 3);`
`IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK = $0f;`

`IEEE80211_WMM_IE_STA_QOSINFO_SP_ALL = $00;`
`IEEE80211_WMM_IE_STA_QOSINFO_SP_2 = $01;`
`IEEE80211_WMM_IE_STA_QOSINFO_SP_4 = $02;`
`IEEE80211_WMM_IE_STA_QOSINFO_SP_6 = $03;`
`IEEE80211_WMM_IE_STA_QOSINFO_SP_MASK = $03;`
`IEEE80211_WMM_IE_STA_QOSINFO_SP_SHIFT = 5;`

`IEEE80211_MESH_FLAGS_AE_A4 = $1;`
`IEEE80211_MESH_FLAGS_AE_A5_A6 = $2;`
`IEEE80211_MESH_FLAGS_AE = $3;`
`IEEE80211_MESH_FLAGS_PS_DEEP = $4;`

`IEEE80211_PREQ_TO_FLAG = (1 shl 0);`	Target only subfield
`IEEE80211_PREQ_USN_FLAG = (1 shl 2);`	Unknown target HWMP sequence number subfield

`IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS = $01;`	STA is willing to establish additional mesh peerings with other mesh STAs
`IEEE80211_MESHCONF_CAPAB_FORWARDING = $08;`	The STA forwards MSDUs
`IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING = $20;`	TBTT adjustment procedure is ongoing
`IEEE80211_MESHCONF_CAPAB_POWER_SAVE_LEVEL = $40;`	STA is in deep sleep mode or has neighbors in deep sleep mode

`WLAN_EID_CHAN_SWITCH_PARAM_TX_RESTRICT = (1 shl 0);`
`WLAN_EID_CHAN_SWITCH_PARAM_INITIATOR = (1 shl 1);`
`WLAN_EID_CHAN_SWITCH_PARAM_REASON = (1 shl 2);`

`IEEE80211_HT_CHANWIDTH_20MHZ = 0;`
`IEEE80211_HT_CHANWIDTH_ANY = 1;`

`IEEE80211_OPMODE_NOTIF_CHANWIDTH_MASK = 3;`
`IEEE80211_OPMODE_NOTIF_CHANWIDTH_20MHZ = 0;`
`IEEE80211_OPMODE_NOTIF_CHANWIDTH_40MHZ = 1;`
`IEEE80211_OPMODE_NOTIF_CHANWIDTH_80MHZ = 2;`
`IEEE80211_OPMODE_NOTIF_CHANWIDTH_160MHZ = 3;`
`IEEE80211_OPMODE_NOTIF_RX_NSS_MASK = $70;`
`IEEE80211_OPMODE_NOTIF_RX_NSS_SHIFT = 4;`
`IEEE80211_OPMODE_NOTIF_RX_NSS_TYPE_BF = $80;`

Note: Supported Rates value encodings in 802.11n-2009 7.3.2.2
`IEEE80211_BSS_MEMBERSHIP_SELECTOR_HT_PHY = 127;`

`IEEE80211_P2P_ATTR_STATUS = 0;`
`IEEE80211_P2P_ATTR_MINOR_REASON = 1;`
`IEEE80211_P2P_ATTR_CAPABILITY = 2;`
`IEEE80211_P2P_ATTR_DEVICE_ID = 3;`
`IEEE80211_P2P_ATTR_GO_INTENT = 4;`
`IEEE80211_P2P_ATTR_GO_CONFIG_TIMEOUT = 5;`
`IEEE80211_P2P_ATTR_LISTEN_CHANNEL = 6;`
`IEEE80211_P2P_ATTR_GROUP_BSSID = 7;`
`IEEE80211_P2P_ATTR_EXT_LISTEN_TIMING = 8;`
`IEEE80211_P2P_ATTR_INTENDED_IFACE_ADDR = 9;`
`IEEE80211_P2P_ATTR_MANAGABILITY = 10;`
`IEEE80211_P2P_ATTR_CHANNEL_LIST = 11;`
`IEEE80211_P2P_ATTR_ABSENCE_NOTICE = 12;`
`IEEE80211_P2P_ATTR_DEVICE_INFO = 13;`
`IEEE80211_P2P_ATTR_GROUP_INFO = 14;`
`IEEE80211_P2P_ATTR_GROUP_ID = 15;`
`IEEE80211_P2P_ATTR_INTERFACE = 16;`
`IEEE80211_P2P_ATTR_OPER_CHANNEL = 17;`
`IEEE80211_P2P_ATTR_INVITE_FLAGS = 18;`
19 - 220: Reserved
`IEEE80211_P2P_ATTR_VENDOR_SPECIFIC = 221;`

`IEEE80211_P2P_ATTR_MAX = 222;`

`IEEE80211_P2P_NOA_DESC_MAX = 4;`

`IEEE80211_P2P_OPPPS_ENABLE_BIT = (1 shl 7);`
`IEEE80211_P2P_OPPPS_CTWINDOW_MASK = $7F;`

`IEEE80211_BAR_CTRL_ACK_POLICY_NORMAL = $0000;`
`IEEE80211_BAR_CTRL_MULTI_TID = $0002;`
`IEEE80211_BAR_CTRL_CBMTID_COMPRESSED_BA = $0004;`
`IEEE80211_BAR_CTRL_TID_INFO_MASK = $f000;`
`IEEE80211_BAR_CTRL_TID_INFO_SHIFT = 12;`

`IEEE80211_HT_MCS_RX_HIGHEST_MASK = $3ff;`
`IEEE80211_HT_MCS_TX_DEFINED = $01;`
`IEEE80211_HT_MCS_TX_RX_DIFF = $02;`
`IEEE80211_HT_MCS_TX_MAX_STREAMS_MASK = $0C;`	value 0 == 1 stream etc
`IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT = 2;`
`IEEE80211_HT_MCS_TX_MAX_STREAMS = 4;`
`IEEE80211_HT_MCS_TX_UNEQUAL_MODULATION = $10;`
802.11n D5.0 20.3.5 / 20.6 says: - indices 0 to 7 and 32 are single spatial stream - 8 to 31 are multiple spatial streams using equal modulation
[8..15 for two streams, 16..23 for three and 24..31 for four] - remainder are multiple spatial streams using unequal modulation
`IEEE80211_HT_MCS_UNEQUAL_MODULATION_START = 33;`
`IEEE80211_HT_MCS_UNEQUAL_MODULATION_START_BYTE = (IEEE80211_HT_MCS_UNEQUAL_MODULATION_START div 8);`

Note: For CapabilitiesInfo
`IEEE80211_HT_CAP_LDPC_CODING = $0001;`
`IEEE80211_HT_CAP_SUP_WIDTH_20_40 = $0002;`
`IEEE80211_HT_CAP_SM_PS = $000C;`
`IEEE80211_HT_CAP_SM_PS_SHIFT = 2;`
`IEEE80211_HT_CAP_GRN_FLD = $0010;`
`IEEE80211_HT_CAP_SGI_20 = $0020;`
`IEEE80211_HT_CAP_SGI_40 = $0040;`
`IEEE80211_HT_CAP_TX_STBC = $0080;`
`IEEE80211_HT_CAP_RX_STBC = $0300;`
`IEEE80211_HT_CAP_RX_STBC_SHIFT = 8;`
`IEEE80211_HT_CAP_DELAY_BA = $0400;`
`IEEE80211_HT_CAP_MAX_AMSDU = $0800;`
`IEEE80211_HT_CAP_DSSSCCK40 = $1000;`
`IEEE80211_HT_CAP_RESERVED = $2000;`
`IEEE80211_HT_CAP_40MHZ_INTOLERANT = $4000;`
`IEEE80211_HT_CAP_LSIG_TXOP_PROT = $8000;`

Note: For ExtendedHTCapInfo
`IEEE80211_HT_EXT_CAP_PCO = $0001;`
`IEEE80211_HT_EXT_CAP_PCO_TIME = $0006;`
`IEEE80211_HT_EXT_CAP_PCO_TIME_SHIFT = 1;`
`IEEE80211_HT_EXT_CAP_MCS_FB = $0300;`
`IEEE80211_HT_EXT_CAP_MCS_FB_SHIFT = 8;`
`IEEE80211_HT_EXT_CAP_HTC_SUP = $0400;`
`IEEE80211_HT_EXT_CAP_RD_RESPONDER = $0800;`

Note: For AMPDUParamsInfo
`IEEE80211_HT_AMPDU_PARM_FACTOR = $03;`
`IEEE80211_HT_AMPDU_PARM_DENSITY = $1C;`
`IEEE80211_HT_AMPDU_PARM_DENSITY_SHIFT = 2;`

Note: Maximum length of AMPDU that the STA can receive in high-throughput (HT). Length = 2 ^ (13 + max_ampdu_length_exp) - 1 (octets) As per Linux ieee80211.h ieee80211_max_ampdu_length_exp
`IEEE80211_HT_MAX_AMPDU_8K = 0;`
`IEEE80211_HT_MAX_AMPDU_16K = 1;`
`IEEE80211_HT_MAX_AMPDU_32K = 2;`
`IEEE80211_HT_MAX_AMPDU_64K = 3;`

Note: Maximum length of AMPDU that the STA can receive in VHT.Length = 2 ^ (13 + max_ampdu_length_exp) - 1 (octets) As per Linux ieee80211.h ieee80211_vht_max_ampdu_length_exp
`IEEE80211_VHT_MAX_AMPDU_8K = 0;`
`IEEE80211_VHT_MAX_AMPDU_16K = 1;`
`IEEE80211_VHT_MAX_AMPDU_32K = 2;`
`IEEE80211_VHT_MAX_AMPDU_64K = 3;`
`IEEE80211_VHT_MAX_AMPDU_128K = 4;`
`IEEE80211_VHT_MAX_AMPDU_256K = 5;`
`IEEE80211_VHT_MAX_AMPDU_512K = 6;`
`IEEE80211_VHT_MAX_AMPDU_1024K = 7;`

`IEEE80211_HT_MAX_AMPDU_FACTOR = 13;`

Note: Minimum MPDU start spacing As per Linux ieee80211.h ieee80211_min_mpdu_spacing
`IEEE80211_HT_MPDU_DENSITY_NONE = 0;`	No restriction
`IEEE80211_HT_MPDU_DENSITY_0_25 = 1;`	1/4 usec
`IEEE80211_HT_MPDU_DENSITY_0_5 = 2;`	1/2 usec
`IEEE80211_HT_MPDU_DENSITY_1 = 3;`	1 usec
`IEEE80211_HT_MPDU_DENSITY_2 = 4;`	2 usec
`IEEE80211_HT_MPDU_DENSITY_4 = 5;`	4 usec
`IEEE80211_HT_MPDU_DENSITY_8 = 6;`	8 usec
`IEEE80211_HT_MPDU_DENSITY_16 = 7;`	16 usec

Note: For HT operation IE HTParam
`IEEE80211_HT_PARAM_CHA_SEC_OFFSET = $03;`
`IEEE80211_HT_PARAM_CHA_SEC_NONE = $00;`
`IEEE80211_HT_PARAM_CHA_SEC_ABOVE = $01;`
`IEEE80211_HT_PARAM_CHA_SEC_BELOW = $03;`
`IEEE80211_HT_PARAM_CHAN_WIDTH_ANY = $04;`
`IEEE80211_HT_PARAM_RIFS_MODE = $08;`

Note: For HT operation IE OperationMode
`IEEE80211_HT_OP_MODE_PROTECTION = $0003;`
`IEEE80211_HT_OP_MODE_PROTECTION_NONE = 0;`
`IEEE80211_HT_OP_MODE_PROTECTION_NONMEMBER = 1;`
`IEEE80211_HT_OP_MODE_PROTECTION_20MHZ = 2;`
`IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED = 3;`
`IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT = $0004;`
`IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT = $0010;`

Note: For HT operation IE STBCParam
`IEEE80211_HT_STBC_PARAM_DUAL_BEACON = $0040;`
`IEEE80211_HT_STBC_PARAM_DUAL_CTS_PROT = $0080;`
`IEEE80211_HT_STBC_PARAM_STBC_BEACON = $0100;`
`IEEE80211_HT_STBC_PARAM_LSIG_TXOP_FULLPROT = $0200;`
`IEEE80211_HT_STBC_PARAM_PCO_ACTIVE = $0400;`
`IEEE80211_HT_STBC_PARAM_PCO_PHASE = $0800;`

`IEEE80211_ADDBA_PARAM_AMSDU_MASK = $0001;`
`IEEE80211_ADDBA_PARAM_POLICY_MASK = $0002;`
`IEEE80211_ADDBA_PARAM_TID_MASK = $003C;`
`IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK = $FFC0;`
`IEEE80211_DELBA_PARAM_TID_MASK = $F000;`
`IEEE80211_DELBA_PARAM_INITIATOR_MASK = $0800;`

Note: According to IEEE802.11n spec size varies from 8K to 64K (in powers of 2)
`IEEE80211_MIN_AMPDU_BUF = $8;`
`IEEE80211_MAX_AMPDU_BUF = $40;`

Note: Spatial Multiplexing Power Save Modes (for capability)
`WLAN_HT_CAP_SM_PS_STATIC = 0;`
`WLAN_HT_CAP_SM_PS_DYNAMIC = 1;`
`WLAN_HT_CAP_SM_PS_INVALID = 2;`
`WLAN_HT_CAP_SM_PS_DISABLED = 3;`

Note: For SM power control field lower two bits
`WLAN_HT_SMPS_CONTROL_DISABLED = 0;`
`WLAN_HT_SMPS_CONTROL_STATIC = 1;`
`WLAN_HT_SMPS_CONTROL_DYNAMIC = 3;`

Note: These definitions are used in each 2-bit subfield of the RXMCSMap and TXMCSMap fields of TIEEE8021VHTMCSInfo, which are both split into 8 subfields by number of streams. These values indicate which MCSes are supported for the number of streams the value appears for.
`IEEE80211_VHT_MCS_SUPPORT_0_7 = 0;`	MCSes 0-7 are supported for the number of streams
`IEEE80211_VHT_MCS_SUPPORT_0_8 = 1;`	MCSes 0-8 are supported
`IEEE80211_VHT_MCS_SUPPORT_0_9 = 2;`	MCSes 0-9 are supported
`IEEE80211_VHT_MCS_NOT_SUPPORTED = 3;`	This number of streams isn't supported

`IEEE80211_VHT_CHANWIDTH_USE_HT = 0;`	Use the HT operation IE to determine the channel width (20 or 40 MHz)
`IEEE80211_VHT_CHANWIDTH_80MHZ = 1;`	80 MHz bandwidth
`IEEE80211_VHT_CHANWIDTH_160MHZ = 2;`	160 MHz bandwidth
`IEEE80211_VHT_CHANWIDTH_80P80MHZ = 3;`	80+80 MHz bandwidth

`IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 = $00000000;`
`IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 = $00000001;`
`IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 = $00000002;`
`IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ = $00000004;`
`IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ = $00000008;`
`IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK = $0000000C;`
`IEEE80211_VHT_CAP_RXLDPC = $00000010;`
`IEEE80211_VHT_CAP_SHORT_GI_80 = $00000020;`
`IEEE80211_VHT_CAP_SHORT_GI_160 = $00000040;`
`IEEE80211_VHT_CAP_TXSTBC = $00000080;`
`IEEE80211_VHT_CAP_RXSTBC_1 = $00000100;`
`IEEE80211_VHT_CAP_RXSTBC_2 = $00000200;`
`IEEE80211_VHT_CAP_RXSTBC_3 = $00000300;`
`IEEE80211_VHT_CAP_RXSTBC_4 = $00000400;`
`IEEE80211_VHT_CAP_RXSTBC_MASK = $00000700;`
`IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE = $00000800;`
`IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE = $00001000;`
`IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT = 13;`
`IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK = (7 shl IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT);`
`IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT = 16;`
`IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK = (7 shl IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT);`
`IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE = $00080000;`
`IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE = $00100000;`
`IEEE80211_VHT_CAP_VHT_TXOP_PS = $00200000;`
`IEEE80211_VHT_CAP_HTC_VHT = $00400000;`
`IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT = 23;`
`IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK = (7 shl IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT);`
`IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_UNSOL_MFB = $08000000;`
`IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_MRQ_MFB = $0c000000;`
`IEEE80211_VHT_CAP_RX_ANTENNA_PATTERN = $10000000;`
`IEEE80211_VHT_CAP_TX_ANTENNA_PATTERN = $20000000;`

`WLAN_AUTH_OPEN = 0;`
`WLAN_AUTH_SHARED_KEY = 1;`
`WLAN_AUTH_FT = 2;`
`WLAN_AUTH_SAE = 3;`
`WLAN_AUTH_LEAP = 128;`

`WLAN_AUTH_CHALLENGE_LEN = 128;`

`WLAN_CAPABILITY_ESS = (1 shl 0);`
`WLAN_CAPABILITY_IBSS = (1 shl 1);`

Note: A mesh STA sets the ESS and IBSS capability bits to zero. However, this holds true for p2p probe responses (in the p2p_find phase) as well.
`WLAN_CAPABILITY_CF_POLLABLE = (1 shl 2);`
`WLAN_CAPABILITY_CF_POLL_REQUEST = (1 shl 3);`
`WLAN_CAPABILITY_PRIVACY = (1 shl 4);`
`WLAN_CAPABILITY_SHORT_PREAMBLE = (1 shl 5);`
`WLAN_CAPABILITY_PBCC = (1 shl 6);`
`WLAN_CAPABILITY_CHANNEL_AGILITY = (1 shl 7);`
802.11h
`WLAN_CAPABILITY_SPECTRUM_MGMT = (1 shl 8);`
`WLAN_CAPABILITY_QOS = (1 shl 9);`
`WLAN_CAPABILITY_SHORT_SLOT_TIME = (1 shl 10);`
`WLAN_CAPABILITY_APSD = (1 shl 11);`
`WLAN_CAPABILITY_RADIO_MEASURE = (1 shl 12);`
`WLAN_CAPABILITY_DSSS_OFDM = (1 shl 13);`
`WLAN_CAPABILITY_DEL_BACK = (1 shl 14);`
`WLAN_CAPABILITY_IMM_BACK = (1 shl 15);`

DMG (60gHz) 802.11ad
Type - bits 0..1
`WLAN_CAPABILITY_DMG_TYPE_MASK = (3 shl 0);`
`WLAN_CAPABILITY_DMG_TYPE_IBSS = (1 shl 0);`	Tx by: STA
`WLAN_CAPABILITY_DMG_TYPE_PBSS = (2 shl 0);`	Tx by: PCP
`WLAN_CAPABILITY_DMG_TYPE_AP = (3 shl 0);`	Tx by: AP

`WLAN_CAPABILITY_DMG_CBAP_ONLY = (1 shl 2);`
`WLAN_CAPABILITY_DMG_CBAP_SOURCE = (1 shl 3);`
`WLAN_CAPABILITY_DMG_PRIVACY = (1 shl 4);`
`WLAN_CAPABILITY_DMG_ECPAC = (1 shl 5);`

`WLAN_CAPABILITY_DMG_SPECTRUM_MGMT = (1 shl 8);`
`WLAN_CAPABILITY_DMG_RADIO_MEASURE = (1 shl 12);`