Difference between revisions of "Unit MMC"
From Ultibo.org
| Line 3,571: | Line 3,571: | ||
|- | |- | ||
| <code>SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS = (1 shl 4);</code> | | <code>SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS = (1 shl 4);</code> | ||
| − | | Controller has flaky internal state so reset it on each ios change | + | | Controller has flaky internal state so reset it on each ios change |
|- | |- | ||
| <code>SDHCI_QUIRK_BROKEN_DMA = (1 shl 5);</code> | | <code>SDHCI_QUIRK_BROKEN_DMA = (1 shl 5);</code> | ||
Revision as of 02:35, 3 January 2017
Return to Unit Reference
Description
Ultibo MMC/SD interface unit
This unit implements the standards based part of the SD/MMC specification including the standard SDHCI interfaces.
For each platform a SDHCI module needs to be provided that implements the platform specific parts of the SDHCI interface.
This is similar in model to USB and other interfaces in Ultibo, where the generic interface unit requires a platform specific module to register with it in order to communicate with platform specific devices.
The SD/MMC interfaces are 2 tier (ie Host and Device) whereas the USB interface is 3 tier (Host, Device and Driver).
Constants
MMC specific constants
MMC_* MMC_NAME_PREFIX = 'MMC';
|
Name prefix for MMC Devices |
MMC_STATUS_TIMER_INTERVAL = 1000;
|
|
MMC_DEFAULT_BLOCKSIZE = 512;
|
|
MMC_DEFAULT_BLOCKSHIFT = 9;
|
|
MMC device type constants
MMC_TYPE_* MMC_TYPE_NONE = 0;
|
|
MMC_TYPE_MMC = 1;
|
|
MMC_TYPE_SD = 2;
|
|
MMC_TYPE_SDIO = 3;
|
|
MMC_TYPE_SD_COMBO = 4;
|
|
MMC_TYPE_MAX = 4;
|
|
MMC device state constants
MMC_STATE_* MMC_STATE_EJECTED = 0;
|
|
MMC_STATE_INSERTED = 1;
|
|
MMC_STATE_MAX = 1;
|
|
MMC device flag constants
MMC_FLAG_* MMC_FLAG_NONE = $00000000;
|
|
MMC_FLAG_CARD_PRESENT = $00000001;
|
|
MMC_FLAG_WRITE_PROTECT = $00000002;
|
|
MMC_FLAG_HIGH_CAPACITY = $00000004;
|
High Capacity (SDHC) |
MMC_FLAG_EXT_CAPACITY = $00000008;
|
Extended Capacity (SDXC) |
MMC_FLAG_UHS_I = $00000010;
|
Ultra High Speed (UHS-I) |
MMC_FLAG_UHS_II = $00000020;
|
Ultra High Speed (UHS-II) |
MMC_FLAG_BLOCK_ADDRESSED = $00000040;
|
Block Addressed (SDHC/SDXC and others) |
MMC_FLAG_DDR_MODE = $00000080;
|
MMC/SD status code constants
MMC_STATUS_* MMC_STATUS_SUCCESS = 0;
|
Function successful |
MMC_STATUS_TIMEOUT = 1;
|
The operation timed out |
MMC_STATUS_NO_MEDIA = 2;
|
No media present in device |
MMC_STATUS_HARDWARE_ERROR = 3;
|
Hardware error of some form occurred |
MMC_STATUS_INVALID_DATA = 4;
|
Invalid data was received |
MMC_STATUS_INVALID_PARAMETER = 5;
|
An invalid parameter was passed to the function |
MMC_STATUS_INVALID_SEQUENCE = 6;
|
Invalid sequence encountered |
MMC_STATUS_OUT_OF_MEMORY = 7;
|
No memory available for operation |
MMC_STATUS_UNSUPPORTED_REQUEST = 8;
|
The request is unsupported |
MMC_STATUS_NOT_PROCESSED = 9;
|
The MMC transfer has not yet been processed |
MMC/SD version constants
SD_VERSION_*, MMC_VERSION_* SD_VERSION_SD = $00020000;
|
|
SD_VERSION_1_0 = (SD_VERSION_SD or $0100);
|
|
SD_VERSION_1_10 = (SD_VERSION_SD or $010a);
|
|
SD_VERSION_2 = (SD_VERSION_SD or $0200);
|
|
SD_VERSION_3 = (SD_VERSION_SD or $0300);
|
|
SD_VERSION_4 = (SD_VERSION_SD or $0400);
|
|
MMC_VERSION_MMC = $00010000;
|
|
MMC_VERSION_1_2 = (MMC_VERSION_MMC or $0102);
|
|
MMC_VERSION_1_4 = (MMC_VERSION_MMC or $0104);
|
|
MMC_VERSION_2_2 = (MMC_VERSION_MMC or $0202);
|
|
MMC_VERSION_3 = (MMC_VERSION_MMC or $0300);
|
|
MMC_VERSION_4 = (MMC_VERSION_MMC or $0400);
|
|
MMC_VERSION_4_1 = (MMC_VERSION_MMC or $0401);
|
|
MMC_VERSION_4_2 = (MMC_VERSION_MMC or $0402);
|
|
MMC_VERSION_4_3 = (MMC_VERSION_MMC or $0403);
|
|
MMC_VERSION_4_41 = (MMC_VERSION_MMC or $0429);
|
|
MMC_VERSION_4_5 = (MMC_VERSION_MMC or $0405);
|
|
MMC_VERSION_5_0 = (MMC_VERSION_MMC or $0500);
|
|
MMC_VERSION_UNKNOWN = (MMC_VERSION_MMC);
|
|
MMC/SD mode constants
MMC_MODE_* MMC_MODE_HS = (1 shl 0);
|
|
MMC_MODE_HS_52MHz = (1 shl 1);
|
|
MMC_MODE_4BIT = (1 shl 2);
|
|
MMC_MODE_8BIT = (1 shl 3);
|
|
MMC_MODE_SPI = (1 shl 4);
|
|
MMC_MODE_HC = (1 shl 5);
|
|
MMC_MODE_DDR_52MHz = (1 shl 6);
|
MMC/SD direction constants
MMC_DATA_* MMC_DATA_READ = 1;
|
|
MMC_DATA_WRITE = 2;
|
MMC/SD bus width constants
MMC_BUS_WIDTH_* MMC_BUS_WIDTH_1 = 0;
|
|
MMC_BUS_WIDTH_4 = 2;
|
|
MMC_BUS_WIDTH_8 = 3;
|
MMC bus speed (Hz) constants
MMC_BUS_SPEED_* MMC_BUS_SPEED_DEFAULT = 0;
|
|
MMC_BUS_SPEED_HS26 = 26000000;
|
|
MMC_BUS_SPEED_HS52 = 52000000;
|
|
MMC_BUS_SPEED_DDR = 52000000;
|
|
MMC_BUS_SPEED_HS200 = 200000000;
|
MMC command constants
MMC_CMD_* | From: /include/linux/mmc/mmc.h | |
| Class 1 | |
MMC_CMD_GO_IDLE_STATE = 0;
|
|
MMC_CMD_SEND_OP_COND = 1;
|
|
MMC_CMD_ALL_SEND_CID = 2;
|
|
MMC_CMD_SET_RELATIVE_ADDR = 3;
|
|
MMC_CMD_SET_DSR = 4;
|
|
MMC_CMD_SLEEP_AWAKE = 5;
|
|
MMC_CMD_SWITCH = 6;
|
|
MMC_CMD_SELECT_CARD = 7;
|
|
MMC_CMD_SEND_EXT_CSD = 8;
|
|
MMC_CMD_SEND_CSD = 9;
|
|
MMC_CMD_SEND_CID = 10;
|
|
MMC_CMD_READ_DAT_UNTIL_STOP = 11;
|
|
MMC_CMD_STOP_TRANSMISSION = 12;
|
|
MMC_CMD_SEND_STATUS = 13;
|
|
MMC_CMD_BUS_TEST_R = 14;
|
|
MMC_CMD_GO_INACTIVE_STATE = 15;
|
|
MMC_CMD_BUS_TEST_W = 19;
|
|
MMC_CMD_SPI_READ_OCR = 58;
|
|
MMC_CMD_SPI_CRC_ON_OFF = 59;
|
|
| Class 2 | |
MMC_CMD_SET_BLOCKLEN = 16;
|
|
MMC_CMD_READ_SINGLE_BLOCK = 17;
|
|
MMC_CMD_READ_MULTIPLE_BLOCK = 18;
|
|
MMC_CMD_SEND_TUNING_BLOCK = 19;
|
|
MMC_CMD_SEND_TUNING_BLOCK_HS200 = 21;
|
|
| Class 3 | |
MMC_CMD_WRITE_DAT_UNTIL_STOP = 20;
|
|
| Class 4 | |
MMC_CMD_SET_BLOCK_COUNT = 23;
|
|
MMC_CMD_WRITE_SINGLE_BLOCK = 24;
|
|
MMC_CMD_WRITE_MULTIPLE_BLOCK = 25;
|
|
MMC_CMD_PROGRAM_CID = 26;
|
|
MMC_CMD_PROGRAM_CSD = 27;
|
|
| Class 6 | |
MMC_CMD_SET_WRITE_PROT = 28;
|
|
MMC_CMD_CLR_WRITE_PROT = 29;
|
|
MMC_CMD_SEND_WRITE_PROT = 30;
|
|
| Class 5 | |
MMC_CMD_ERASE_GROUP_START = 35;
|
|
MMC_CMD_ERASE_GROUP_END = 36;
|
|
MMC_CMD_ERASE = 38;
|
|
| Class 9 | |
MMC_CMD_FAST_IO = 39;
|
|
MMC_CMD_GO_IRQ_STATE = 40;
|
|
| Class 7 | |
MMC_CMD_LOCK_UNLOCK = 42;
|
|
| Class 8 | |
MMC_CMD_APP_CMD = 55;
|
|
MMC_CMD_GEN_CMD = 56;
|
|
MMC_CMD_RES_MAN = 62;
|
|
MMC_CMD62_ARG1 = $EFAC62EC;
|
|
MMC_CMD62_ARG2 = $00CBAEA7;
|
|
MMC response type constants
MMC_RSP_* | From: /include/linux/mmc/mmc.h | |
| Native | |
MMC_RSP_PRESENT = (1 shl 0);
|
|
MMC_RSP_136 = (1 shl 1);
|
136 bit response |
MMC_RSP_CRC = (1 shl 2);
|
Expect valid crc |
MMC_RSP_BUSY = (1 shl 3);
|
Card may send busy |
MMC_RSP_OPCODE = (1 shl 4);
|
Response contains opcode |
| These are the native response types, and correspond to valid bit patterns of the above flags. One additional valid pattern is all zeros, which means we don't expect a response. | |
MMC_RSP_NONE = (0);
|
|
MMC_RSP_R1 = (MMC_RSP_PRESENT or MMC_RSP_CRC or MMC_RSP_OPCODE);
|
|
MMC_RSP_R1B = (MMC_RSP_PRESENT or MMC_RSP_CRC or MMC_RSP_OPCODE or MMC_RSP_BUSY);
|
|
MMC_RSP_R2 = (MMC_RSP_PRESENT or MMC_RSP_136 or MMC_RSP_CRC);
|
|
MMC_RSP_R3 = (MMC_RSP_PRESENT);
|
|
MMC_RSP_R4 = (MMC_RSP_PRESENT);
|
|
MMC_RSP_R5 = (MMC_RSP_PRESENT or MMC_RSP_CRC or MMC_RSP_OPCODE);
|
|
MMC_RSP_R6 = (MMC_RSP_PRESENT or MMC_RSP_CRC or MMC_RSP_OPCODE);
|
|
MMC_RSP_R7 = (MMC_RSP_PRESENT or MMC_RSP_CRC or MMC_RSP_OPCODE);
|
|
| SPI | |
MMC_RSP_SPI_S1 = (1 shl 7);
|
One status byte |
MMC_RSP_SPI_S2 = (1 shl 8);
|
Second byte |
MMC_RSP_SPI_B4 = (1 shl 9);
|
Four data bytes |
MMC_RSP_SPI_BUSY = (1 shl 10);
|
Card may send busy |
| These are the SPI response types for MMC, SD, and SDIO cards. Commands return R1, with maybe more info. Zero is an error type, callers must always provide the appropriate MMC_RSP_SPI_Rx flags. | |
MMC_RSP_SPI_R1 = (MMC_RSP_SPI_S1);
|
|
MMC_RSP_SPI_R1B = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_BUSY);
|
|
MMC_RSP_SPI_R2 = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_S2);
|
|
MMC_RSP_SPI_R3 = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_B4);
|
|
MMC_RSP_SPI_R4 = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_B4);
|
|
MMC_RSP_SPI_R5 = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_S2);
|
|
MMC_RSP_SPI_R7 = (MMC_RSP_SPI_S1 or MMC_RSP_SPI_B4);
|
|
MMC response value constants
MMC_RSP_R1_*, MMC_RSP_R2_* | R1 - MMC status in R1, for native mode (SPI bits are different) | |
MMC_RSP_R1_OUT_OF_RANGE = (1 shl 31);
|
|
MMC_RSP_R1_ADDRESS_ERROR = (1 shl 30);
|
|
MMC_RSP_R1_BLOCK_LEN_ERROR = (1 shl 29);
|
|
MMC_RSP_R1_ERASE_SEQ_ERROR = (1 shl 28);
|
|
MMC_RSP_R1_ERASE_PARAM = (1 shl 27);
|
|
MMC_RSP_R1_WP_VIOLATION = (1 shl 26);
|
|
MMC_RSP_R1_CARD_IS_LOCKED = (1 shl 25);
|
|
MMC_RSP_R1_LOCK_UNLOCK_FAILED = (1 shl 24);
|
|
MMC_RSP_R1_COM_CRC_ERROR = (1 shl 23);
|
|
MMC_RSP_R1_ILLEGAL_COMMAND = (1 shl 22);
|
|
MMC_RSP_R1_CARD_ECC_FAILED = (1 shl 21);
|
|
MMC_RSP_R1_CC_ERROR = (1 shl 20);
|
|
MMC_RSP_R1_ERROR = (1 shl 19);
|
|
MMC_RSP_R1_UNDERRUN = (1 shl 18);
|
|
MMC_RSP_R1_OVERRUN = (1 shl 17);
|
|
MMC_RSP_R1_CID_CSD_OVERWRITE = (1 shl 16);
|
|
MMC_RSP_R1_WP_ERASE_SKIP = (1 shl 15);
|
|
MMC_RSP_R1_CARD_ECC_DISABLED = (1 shl 14);
|
|
MMC_RSP_R1_ERASE_RESET = (1 shl 13);
|
|
MMC_RSP_R1_READY_FOR_DATA = (1 shl 8);
|
|
MMC_RSP_R1_SWITCH_ERROR = (1 shl 7);
|
|
MMC_RSP_R1_EXCEPTION_EVENT = (1 shl 6);
|
|
MMC_RSP_R1_APP_CMD = (1 shl 5);
|
|
MMC_RSP_R1_AKE_SEQ_ERROR = (1 shl 3);
|
|
| R1 SPI - MMC/SD in SPI mode reports R1 status always, and R2 for SEND_STATUS. R1 is the low order byte, R2 is the next highest byte, when present. | |
MMC_RSP_R1_SPI_IDLE = (1 shl 0);
|
|
MMC_RSP_R1_SPI_ERASE_RESET = (1 shl 1);
|
|
MMC_RSP_R1_SPI_ILLEGAL_COMMAND = (1 shl 2);
|
|
MMC_RSP_R1_SPI_COM_CRC = (1 shl 3);
|
|
MMC_RSP_R1_SPI_ERASE_SEQ = (1 shl 4);
|
|
MMC_RSP_R1_SPI_ADDRESS = (1 shl 5);
|
|
MMC_RSP_R1_SPI_PARAMETER = (1 shl 6);
|
|
| R1 bit 7 is always zero | |
| R2 SPI - See above | |
MMC_RSP_R2_SPI_CARD_LOCKED = (1 shl 8);
|
|
MMC_RSP_R2_SPI_WP_ERASE_SKIP = (1 shl 9);
|
Or lock/unlock fail |
MMC_RSP_R2_SPI_LOCK_UNLOCK_FAIL = MMC_RSP_R2_SPI_WP_ERASE_SKIP;
|
|
MMC_RSP_R2_SPI_ERROR = (1 shl 10);
|
|
MMC_RSP_R2_SPI_CC_ERROR = (1 shl 11);
|
|
MMC_RSP_R2_SPI_CARD_ECC_ERROR = (1 shl 12);
|
|
MMC_RSP_R2_SPI_WP_VIOLATION = (1 shl 13);
|
|
MMC_RSP_R2_SPI_ERASE_PARAM = (1 shl 14);
|
|
MMC_RSP_R2_SPI_OUT_OF_RANGE = (1 shl 15);
|
Or CSD overwrite |
MMC_RSP_R2_SPI_CSD_OVERWRITE = MMC_RSP_R2_SPI_OUT_OF_RANGE;
|
|
MMC operation condition register (OCR) value constants
MMC_OCR_* | See: Section 5.1 of SD Physical Layer Simplified Specification V4.10 | |
MMC_OCR_BUSY = $80000000;
|
Busy Status - 0 = Initializing / 1 = Initialization Complete |
MMC_OCR_HCS = $40000000;
|
Card Capacity Status - 0 = SDSC / 1 = SDHC or SDXC |
MMC_OCR_UHS_II = $20000000;
|
UHS-II Card Status - 0 = Non UHS-II Card / 1 = UHS-II Card |
MMC_OCR_S18A = $01000000;
|
Switching to 1.8V Accepted - 0 = Continue current voltage signaling / 1 = Ready for switching signal voltage |
MMC_OCR_VOLTAGE_MASK = $007FFF80;
|
|
MMC_OCR_ACCESS_MODE = $60000000;
|
|
MMC card status register (CSR) value constants
MMC_CARD_STATUS_* | See: Section 4.10.1 of SD Physical Layer Simplified Specification Version 4.10 | |
| Note: These map to the Native mode R1 response values | |
MMC_CARD_STATUS_MASK = not($0206BF7F);
|
|
MMC_CARD_STATUS_ERROR = (1 shl 19);
|
|
MMC_CARD_STATUS_CURRENT_STATE = ($0F shl 9);
|
See MMC_CURRENT_STATE_ definitions below |
MMC_CARD_STATUS_READY_FOR_DATA = (1 shl 8);
|
|
MMC_CARD_STATUS_SWITCH_ERROR = (1 shl 7);
|
|
MMC current state value constants
MMC_CURRENT_STATE_* | From Card Status Register or R1 Response | |
MMC_CURRENT_STATE_IDLE = (0 shl 9);
|
|
MMC_CURRENT_STATE_READY = (1 shl 9);
|
|
MMC_CURRENT_STATE_IDENT = (2 shl 9);
|
|
MMC_CURRENT_STATE_STBY = (3 shl 9);
|
|
MMC_CURRENT_STATE_TRAN = (4 shl 9);
|
|
MMC_CURRENT_STATE_DATA = (5 shl 9);
|
|
MMC_CURRENT_STATE_RCV = (6 shl 9);
|
|
MMC_CURRENT_STATE_PRG = (7 shl 9);
|
|
MMC_CURRENT_STATE_DIS = (8 shl 9);
|
|
MMC card identification data (CID) value constants
MMC_CID_* | See: Section 5.2 of SD Physical Layer Simplified Specification Version 4.10 | |
| MMC CID Fields | |
MMC_CID_MID = 1;
|
Manufacturer ID |
MMC_CID_OID = 2;
|
OEM/Application ID |
MMC_CID_PNM0 = 3;
|
Product name (Byte 0) |
MMC_CID_PNM1 = 4;
|
Product name (Byte 1) |
MMC_CID_PNM2 = 5;
|
Product name (Byte 2) |
MMC_CID_PNM3 = 6;
|
Product name (Byte 3) |
MMC_CID_PNM4 = 7;
|
Product name (Byte 4) |
MMC_CID_PNM5 = 8;
|
Product name (Byte 5) |
MMC_CID_PNM6 = 9;
|
Product name (Byte 6) |
MMC_CID_PRV = 10;
|
Product revision |
MMC_CID_HRV = 11;
|
Hardware revision |
MMC_CID_FRV = 12;
|
Firmware revision |
MMC_CID_PSN = 13;
|
Product serial number |
MMC_CID_MDT_YEAR = 14;
|
Manufacturing year |
MMC_CID_MDT_MONTH = 15;
|
Manufacturing month |
MMC_CID_CRC = 16;
|
CRC |
MMC card specific data (CSD) value constants
MMC_CSD_* | See: Section 5.3 of SD Physical Layer Simplified Specification Version 4.10 | |
| MMC CSD Fields | |
MMC_CSD_STRUCTURE = 1;
|
|
MMC_CSD_SPECVER = 2;
|
MMC/eMMC Only |
MMC_CSD_TAAC_UNIT = 3;
|
|
MMC_CSD_TAAC_VALUE = 4;
|
|
MMC_CSD_NSAC = 5;
|
|
MMC_CSD_TRAN_SPEED_UNIT = 6;
|
|
MMC_CSD_TRAN_SPEED_VALUE = 37;
|
|
MMC_CSD_CCC = 7;
|
|
MMC_CSD_READ_BL_LEN = 8;
|
|
MMC_CSD_READ_BL_PARTIAL = 9;
|
|
MMC_CSD_WRITE_BLK_MISALIGN = 10;
|
|
MMC_CSD_READ_BLK_MISALIGN = 11;
|
|
MMC_CSD_DSR_IMP = 12;
|
|
MMC_CSD_C_SIZE = 13;
|
|
MMC_CSD_VDD_R_CURR_MIN = 14;
|
|
MMC_CSD_VDD_R_CURR_MAX = 15;
|
|
MMC_CSD_VDD_W_CURR_MIN = 16;
|
|
MMC_CSD_VDD_W_CURR_MAX = 17;
|
|
MMC_CSD_C_SIZE_MULT = 18;
|
|
MMC_CSD_ERASE_BLK_EN = 19;
|
SD Specification |
MMC_CSD_SECTOR_SIZE = 20;
|
MMC/eMMC Specification / SD Specification |
MMC_CSD_ERASE_GRP_SIZE = 21;
|
MMC/eMMC Specification |
MMC_CSD_ERASE_GRP_MULT = 22;
|
MMC/eMMC Specification |
MMC_CSD_WP_GRP_SIZE = 23;
|
|
MMC_CSD_WP_GRP_ENABLE = 24;
|
|
MMC_CSD_DEFAULT_ECC = 25;
|
MMC/eMMC Only |
MMC_CSD_R2W_FACTOR = 26;
|
|
MMC_CSD_WRITE_BL_LEN = 27;
|
|
MMC_CSD_WRITE_BL_PARTIAL = 28;
|
|
MMC_CSD_CONTENT_PROT_APP = 29;
|
MMC/eMMC Only |
MMC_CSD_FILE_FORMAT_GRP = 30;
|
|
MMC_CSD_COPY = 31;
|
|
MMC_CSD_PERM_WRITE_PROTECT = 32;
|
|
MMC_CSD_TMP_WRITE_PROTECT = 33;
|
|
MMC_CSD_FILE_FORMAT = 34;
|
|
MMC_CSD_ECC = 35;
|
MMC/eMMC Only |
MMC_CSD_CRC = 36;
|
|
MMC CSD structure value constants
MMC_CSD_STRUCT_* MMC_CSD_STRUCT_VER_1_0 = 0;
|
Valid for system specification 1.0 - 1.2 |
MMC_CSD_STRUCT_VER_1_1 = 1;
|
Valid for system specification 1.4 - 2.2 |
MMC_CSD_STRUCT_VER_1_2 = 2;
|
Valid for system specification 3.1 - 3.2 - 3.31 - 4.0 - 4.1 |
MMC_CSD_STRUCT_EXT_CSD = 3;
|
Version is coded in CSD_STRUCTURE in EXT_CSD |
MMC CSD spec version value constants
MMC_CSD_SPEC_VER_* MMC_CSD_SPEC_VER_0 = 0;
|
Implements system specification 1.0 - 1.2 |
MMC_CSD_SPEC_VER_1 = 1;
|
Implements system specification 1.4 |
MMC_CSD_SPEC_VER_2 = 2;
|
Implements system specification 2.0 - 2.2 |
MMC_CSD_SPEC_VER_3 = 3;
|
Implements system specification 3.1 - 3.2 - 3.31 |
MMC_CSD_SPEC_VER_4 = 4;
|
Implements system specification 4.0 - 4.1 |
MMC CSD TAAC time unit constants
MMC_CSD_TAAC_UNITS* MMC_CSD_TAAC_UNITS:array[0..7] of LongWord = (
| |
1,
|
|
10,
|
|
100,
|
|
1000,
|
|
10000,
|
|
100000,
|
|
1000000,
|
|
10000000);
|
|
MMC CSD TAAC time value constants
MMC_CSD_TAAC_VALUES* MMC_CSD_TAAC_VALUES:array[0..15] of LongWord = (
| |
0,
|
|
10,
|
|
12,
|
|
13,
|
|
15,
|
|
20,
|
|
25,
|
|
30,
|
|
35,
|
|
40,
|
|
45,
|
|
50,
|
|
55,
|
|
60,
|
|
70,
|
|
80);
|
|
MMC CSD card command class (CCC) value constants
MMC_CCC_* | See: Table 4-21 (Page 68) of SD Physical Layer Simplified Specification V4.10 | |
MMC_CCC_BASIC = (1 shl 0);
|
(Class 0) Basic protocol functions (CMD0,1,2,3,4,7,9,10,12,13,15) (and for SPI, CMD58,59) |
MMC_CCC_STREAM_READ = (1 shl 1);
|
(Class 1) Stream read commands (CMD11) |
MMC_CCC_BLOCK_READ = (1 shl 2);
|
(Class 2) Block read commands (CMD16,17,18) |
MMC_CCC_STREAM_WRITE = (1 shl 3);
|
(Class 3) Stream write commands (CMD20) |
MMC_CCC_BLOCK_WRITE = (1 shl 4);
|
(Class 4) Block write commands (CMD16,24,25,26,27) |
MMC_CCC_ERASE = (1 shl 5);
|
(Class 5) Ability to erase blocks (CMD32,33,34,35,36,37,38,39) |
MMC_CCC_WRITE_PROT = (1 shl 6);
|
(Class 6) Ability to write protect blocks (CMD28,29,30) |
MMC_CCC_LOCK_CARD = (1 shl 7);
|
(Class 7) Ability to lock down card (CMD16,CMD42) |
MMC_CCC_APP_SPEC = (1 shl 8);
|
(Class 8) Application specific (CMD55,56,57,ACMD*) |
MMC_CCC_IO_MODE = (1 shl 9);
|
(Class 9) I/O mode (CMD5,39,40,52,53) |
MMC_CCC_SWITCH = (1 shl 10);
|
(Class 10) High speed switch (CMD6,34,35,36,37,50) |
MMC_CCC_EXTENSION = (1 shl 11);
|
(Class 11) Extension (CMD?) |
MMC CSD transfer speed rate unit constants
MMC_CSD_TRAN_SPEED_UNITS* MMC_CSD_TRAN_SPEED_UNITS:array[0..7] of LongWord = (
| |
10000,
|
|
100000,
|
|
1000000,
|
|
10000000,
|
|
0,
|
|
0,
|
|
0,
|
|
0);
|
|
MMC CSD transfer speed time value constants
MMC_CSD_TRAN_SPEED_VALUES* MMC_CSD_TRAN_SPEED_VALUES:array[0..15] of LongWord = (
| |
0,
|
|
10,
|
|
12,
|
|
13,
|
|
15,
|
|
20,
|
|
25,
|
|
30,
|
|
35,
|
|
40,
|
|
45,
|
|
50,
|
|
55,
|
|
60,
|
|
70,
|
|
80);
|
|
SECURE_ERASE = $80000000;
|
Used by MMC_CMD_ERASE |
MMC voltage value constants
MMC_VDD_* MMC_VDD_165_195 = $00000080;
|
VDD voltage 1.65 - 1.95 |
MMC_VDD_20_21 = $00000100;
|
VDD voltage 2.0 ~ 2.1 |
MMC_VDD_21_22 = $00000200;
|
VDD voltage 2.1 ~ 2.2 |
MMC_VDD_22_23 = $00000400;
|
VDD voltage 2.2 ~ 2.3 |
MMC_VDD_23_24 = $00000800;
|
VDD voltage 2.3 ~ 2.4 |
MMC_VDD_24_25 = $00001000;
|
VDD voltage 2.4 ~ 2.5 |
MMC_VDD_25_26 = $00002000;
|
VDD voltage 2.5 ~ 2.6 |
MMC_VDD_26_27 = $00004000;
|
VDD voltage 2.6 ~ 2.7 |
MMC_VDD_27_28 = $00008000;
|
VDD voltage 2.7 ~ 2.8 |
MMC_VDD_28_29 = $00010000;
|
VDD voltage 2.8 ~ 2.9 |
MMC_VDD_29_30 = $00020000;
|
VDD voltage 2.9 ~ 3.0 |
MMC_VDD_30_31 = $00040000;
|
VDD voltage 3.0 ~ 3.1 |
MMC_VDD_31_32 = $00080000;
|
VDD voltage 3.1 ~ 3.2 |
MMC_VDD_32_33 = $00100000;
|
VDD voltage 3.2 ~ 3.3 |
MMC_VDD_33_34 = $00200000;
|
VDD voltage 3.3 ~ 3.4 |
MMC_VDD_34_35 = $00400000;
|
VDD voltage 3.4 ~ 3.5 |
MMC_VDD_35_36 = $00800000;
|
VDD voltage 3.5 ~ 3.6 |
MMC switch mode value constants
MMC_SWITCH_MODE_* MMC_SWITCH_MODE_CMD_SET = $00;
|
Change the command set |
MMC_SWITCH_MODE_SET_BITS = $01;
|
Set bits in EXT_CSD byte addressed by index which are 1 in value field |
MMC_SWITCH_MODE_CLEAR_BITS = $02;
|
Clear bits in EXT_CSD byte addressed by index, which are 1 in value field |
MMC_SWITCH_MODE_WRITE_BYTE = $03;
|
Set target byte to value |
MMC EXT_CSD field constants
EXT_CSD_* EXT_CSD_ENH_START_ADDR = 136;
|
R/W |
EXT_CSD_ENH_SIZE_MULT = 140;
|
R/W |
EXT_CSD_GP_SIZE_MULT = 143;
|
R/W |
EXT_CSD_PARTITION_SETTING = 155;
|
R/W |
EXT_CSD_PARTITIONS_ATTRIBUTE = 156;
|
R/W |
EXT_CSD_MAX_ENH_SIZE_MULT = 157;
|
R |
EXT_CSD_PARTITIONING_SUPPORT = 160;
|
RO |
EXT_CSD_RST_N_FUNCTION = 162;
|
R/W |
EXT_CSD_WR_REL_PARAM = 166;
|
R |
EXT_CSD_WR_REL_SET = 167;
|
R/W |
EXT_CSD_RPMB_MULT = 168;
|
RO |
EXT_CSD_ERASE_GROUP_DEF = 175;
|
R/W |
EXT_CSD_BOOT_BUS_WIDTH = 177;
|
|
EXT_CSD_PART_CONF = 179;
|
R/W |
EXT_CSD_BUS_WIDTH = 183;
|
R/W |
EXT_CSD_HS_TIMING = 185;
|
R/W |
EXT_CSD_REV = 192;
|
RO |
EXT_CSD_CARD_TYPE = 196;
|
RO |
EXT_CSD_SEC_CNT = 212;
|
RO, 4 bytes |
EXT_CSD_HC_WP_GRP_SIZE = 221;
|
RO |
EXT_CSD_HC_ERASE_GRP_SIZE = 224;
|
RO |
EXT_CSD_BOOT_MULT = 226;
|
RO |
MMC EXT_CSD field definition constants
EXT_CSD_* EXT_CSD_CMD_SET_NORMAL = (1 shl 0);
|
|
EXT_CSD_CMD_SET_SECURE = (1 shl 1);
|
|
EXT_CSD_CMD_SET_CPSECURE = (1 shl 2);
|
|
EXT_CSD_CARD_TYPE_26 = (1 shl 0);
|
Card can run at 26MHz |
EXT_CSD_CARD_TYPE_52 = (1 shl 1);
|
Card can run at 52MHz |
EXT_CSD_CARD_TYPE_DDR_1_8V = (1 shl 2);
|
|
EXT_CSD_CARD_TYPE_DDR_1_2V = (1 shl 3);
|
|
EXT_CSD_CARD_TYPE_DDR_52 = (EXT_CSD_CARD_TYPE_DDR_1_8V or EXT_CSD_CARD_TYPE_DDR_1_2V);
|
|
EXT_CSD_BUS_WIDTH_1 = 0;
|
Card is in 1 bit mode |
EXT_CSD_BUS_WIDTH_4 = 1;
|
Card is in 4 bit mode |
EXT_CSD_BUS_WIDTH_8 = 2;
|
Card is in 8 bit mode |
EXT_CSD_DDR_BUS_WIDTH_4 = 5;
|
Card is in 4 bit DDR mode |
EXT_CSD_DDR_BUS_WIDTH_8 = 6;
|
Card is in 8 bit DDR mode |
EXT_CSD_BOOT_ACK_ENABLE = (1 shl 6);
|
|
EXT_CSD_BOOT_PARTITION_ENABLE = (1 shl 3);
|
|
EXT_CSD_PARTITION_ACCESS_ENABLE = (1 shl 0);
|
|
EXT_CSD_PARTITION_ACCESS_DISABLE = (0 shl 0);
|
|
EXT_CSD_PARTITION_SETTING_COMPLETED = (1 shl 0);
|
|
EXT_CSD_ENH_USR = (1 shl 0);
|
user data area is enhanced |
EXT_CSD_HS_CTRL_REL = (1 shl 0);
|
host controlled WR_REL_SET |
EXT_CSD_WR_DATA_REL_USR = (1 shl 0);
|
user data area WR_REL |
MMC Misc constants
MMCPART_*, MMC_MAX_* MMCPART_NOAVAILABLE = ($ff);
|
|
PART_ACCESS_MASK = ($07);
|
|
PART_SUPPORT = ($01);
|
|
ENHNCD_SUPPORT = ($02);
|
|
PART_ENH_ATTRIB = ($1f);
|
|
| Maximum block size for MMC | |
MMC_MAX_BLOCK_LEN = 512;
|
|
| Maximum block count for MMC | |
MMC_MAX_BLOCK_COUNT = 65535;
|
|
| The number of MMC physical partitions. These consist of: boot partitions (2), general purpose partitions (4) in MMC v4.4. | |
MMC_NUM_BOOT_PARTITION = 2;
|
|
MMC_PART_RPMB = 3;
|
RPMB partition number |
MMC logging constants
MMC_LOG_* MMC_LOG_LEVEL_DEBUG = LOG_LEVEL_DEBUG;
|
MMC debugging messages |
MMC_LOG_LEVEL_INFO = LOG_LEVEL_INFO;
|
MMC informational messages, such as a device being attached or detached |
MMC_LOG_LEVEL_ERROR = LOG_LEVEL_ERROR;
|
MMC error messages |
MMC_LOG_LEVEL_NONE = LOG_LEVEL_NONE;
|
No MMC messages |
SD specific constants
SD_* SD_DEFAULT_BLOCKSIZE = 512;
|
|
SD_DEFAULT_BLOCKSHIFT = 9;
|
SD bus width constants
SD_BUS_WIDTH_* SD_BUS_WIDTH_1 = 0;
|
|
SD_BUS_WIDTH_4 = 2;
|
SD bus speed (Hz) constants
SD_BUS_SPEED_* SD_BUS_SPEED_DEFAULT = 25000000;
|
|
SD_BUS_SPEED_HS = 50000000;
|
|
SD_BUS_SPEED_UHS_SDR12 = 25000000;
|
|
SD_BUS_SPEED_UHS_SDR25 = 50000000;
|
|
SD_BUS_SPEED_UHS_DDR50 = 50000000;
|
|
SD_BUS_SPEED_UHS_SDR50 = 100000000;
|
|
SD_BUS_SPEED_UHS_SDR104 = 208000000;
|
SD command constants
SD_CMD_* | From: /include/linux/mmc/sd.h | |
| Class 0 | |
SD_CMD_SEND_RELATIVE_ADDR = 3;
|
|
SD_CMD_SEND_IF_COND = 8;
|
|
SD_CMD_SWITCH_VOLTAGE = 11;
|
|
| Class 10 | |
SD_CMD_SWITCH = 6;
|
See: 4.3.10 Switch Function Command |
| Class 5 | |
SD_CMD_ERASE_WR_BLK_START = 32;
|
|
SD_CMD_ERASE_WR_BLK_END = 33;
|
|
| Application commands | |
SD_CMD_APP_SET_BUS_WIDTH = 6;
|
|
SD_CMD_APP_SD_STATUS = 13;
|
|
SD_CMD_APP_SEND_NUM_WR_BLKS = 22;
|
|
SD_CMD_APP_SEND_OP_COND = 41;
|
|
SD_CMD_APP_SEND_SCR = 51;
|
|
| SD_CMD_SWITCH argument format: | |
[31] Check (0) or switch (1)
|
|
[30:24] Reserved (0)
|
|
[23:20] Function group 6
|
|
[19:16] Function group 5
|
|
[15:12] Function group 4
|
|
[11:8] Function group 3
|
|
[7:4] Function group 2
|
|
[3:0] Function group 1
|
|
SD switch mode value constants
SD_SWITCH_MODE_* SD_SWITCH_MODE_CHECK = 0;
|
|
SD_SWITCH_MODE_SWITCH = 1;
|
SD switch function group constants
SD_SWITCH_FUNCTION_GROUP_* SD_SWITCH_FUNCTION_GROUP_ACCESS = 0;
|
Access Mode |
SD_SWITCH_FUNCTION_GROUP_COMMAND = 1;
|
Command System |
SD_SWITCH_FUNCTION_GROUP_DRIVER = 2;
|
Driver Strength |
SD_SWITCH_FUNCTION_GROUP_POWER = 3;
|
Power Limit |
SD switch access mode constants
SD_SWITCH_ACCESS_MODE_* SD_SWITCH_ACCESS_MODE_DEF = 0;
|
Default SDR12 |
SD_SWITCH_ACCESS_MODE_HS = 1;
|
High Speed SDR25 |
SD_SWITCH_ACCESS_MODE_SDR50 = 2;
|
SDR50 (1.8V only) |
SD_SWITCH_ACCESS_MODE_SDR104 = 3;
|
SDR104 (1.8V only) |
SD_SWITCH_ACCESS_MODE_DDR50 = 4;
|
DDR50 (1.8V only) |
SD switch command system constants
SD_SWITCH_COMMAND_SYSTEM_* SD_SWITCH_COMMAND_SYSTEM_DEF = 0;
|
Default |
SD_SWITCH_COMMAND_SYSTEM_EC = 1;
|
For eC |
SD_SWITCH_COMMAND_SYSTEM_OTP = 3;
|
OTP |
SD_SWITCH_COMMAND_SYSTEM_ASSD = 4;
|
ASSD |
SD switch driver strength constants
SD_SWITCH_DRIVER_STRENGTH_* SD_SWITCH_DRIVER_STRENGTH_DEF = 0;
|
Default Type B |
SD_SWITCH_DRIVER_STRENGTH_TYPE_A = 1;
|
Type A |
SD_SWITCH_DRIVER_STRENGTH_TYPE_C = 2;
|
Type C |
SD_SWITCH_DRIVER_STRENGTH_TYPE_D = 3;
|
Type D |
SD switch power limit constants
SD_SWITCH_POWER_LIMIT_* SD_SWITCH_POWER_LIMIT_DEF = 0;
|
Default 0.72W |
SD_SWITCH_POWER_LIMIT_144 = 1;
|
1.44W |
SD_SWITCH_POWER_LIMIT_216 = 2;
|
2.16W (Embedded only) |
SD_SWITCH_POWER_LIMIT_216 = 2;
|
2.16W (Embedded only) |
SD_SWITCH_POWER_LIMIT_288 = 3;
|
2.88W (Embedded only) |
SD_SWITCH_POWER_LIMIT_180 = 4;
|
1.80W |
SD send interface condition value constants
SD_SEND_IF_COND_* SD_SEND_IF_COND_CHECK_PATTERN = $AA;
|
|
SD_SEND_IF_COND_VOLTAGE_MASK = $00FF8000;
|
MMC_VDD_27_28, MMC_VDD_28_29, MMC_VDD_29_30, MMC_VDD_30_31, MMC_VDD_31_32, MMC_VDD_32_33, MMC_VDD_33_34, MMC_VDD_34_35, MMC_VDD_35_36 |
| SD_CMD_SEND_IF_COND argument format: | |
[31:12] Reserved (0)
|
|
[11:8] Host Voltage Supply Flags
|
|
[7:0] Check Pattern (0xAA)
|
|
SD send operation condition value constants
SD_SEND_OP_COND_* SD_SEND_OP_COND_VOLTAGE_MASK = $00FF8000;
|
MMC_VDD_27_28, MMC_VDD_28_29, MMC_VDD_29_30, MMC_VDD_30_31, MMC_VDD_31_32, MMC_VDD_32_33, MMC_VDD_33_34, MMC_VDD_34_35, MMC_VDD_35_36 |
SD operation condition register value constants
SD_OCR_* | See: Section 5.1 of SD Physical Layer Simplified Specification V4.10 | |
SD_OCR_CCS = $40000000;
|
Card Capacity Status - 0 = SDSC / 1 = SDHC or SDXC |
SD_OCR_CCS = $40000000;
|
Card Capacity Status - 0 = SDSC / 1 = SDHC or SDXC |
SD_OCR_UHS_II = $20000000;
|
UHS-II Card Status - 0 = Non UHS-II Card / 1 = UHS-II Card |
SD_OCR_XPC = $10000000;
|
SDXC Power Control |
SD_OCR_S18A = $01000000;
|
1.8V Switching Accepted |
SD CSD structure value constants
SD_CSD_STRUCT_* SD_CSD_STRUCT_VER_1_0 = 0;
|
Standard Capacity |
SD_CSD_STRUCT_VER_2_0 = 1;
|
High Capacity and Extended Capacity |
SD SD status register (SSR) value constants
SD_SSR_* | See: Section 4.10.2 of SD Physical Layer Simplified Specification Version 4.10 | |
| SD SSR Fields | |
SD_SSR_DAT_BUS_WIDTH = 1;
|
|
SD_SSR_SECURED_MODE = 2;
|
|
SD_SSR_SD_CARD_TYPE = 3;
|
|
SD_SSR_SIZE_OF_PROTECTED_AREA = 4;
|
|
SD_SSR_SPEED_CLASS = 5;
|
|
SD_SSR_PERFORMANCE_MOVE = 6;
|
|
SD_SSR_AU_SIZE = 7;
|
|
SD_SSR_ERASE_SIZE = 8;
|
|
SD_SSR_ERASE_TIMEOUT = 9;
|
|
SD_SSR_ERASE_OFFSET = 10;
|
|
SD_SSR_UHS_SPEED_GRADE = 11;
|
|
SD_SSR_UHS_AU_SIZE = 12;
|
|
SD SSR bus width value constants
SD_SSR_BUS_WIDTH_* SD_SSR_BUS_WIDTH_1 = 0;
|
1 (default) |
SD_SSR_BUS_WIDTH_4 = 2;
|
4 bit width |
SD SSR card type value constants
SD_SSR_CARD_TYPE_* SD_SSR_CARD_TYPE_RW = $0000;
|
Regular SD RD/WR Card |
SD_SSR_CARD_TYPE_ROM = $0001;
|
SD ROM Card |
SD_SSR_CARD_TYPE_OTP = $0002;
|
OTP |
SD SSR speed class value constants
SD_SSR_SPEED_CLASS_* SD_SSR_SPEED_CLASS_0 = $00;
|
Class 0 |
SD_SSR_SPEED_CLASS_2 = $01;
|
Class 2 |
SD_SSR_SPEED_CLASS_4 = $02;
|
Class 4 |
SD_SSR_SPEED_CLASS_6 = $03;
|
Class 6 |
SD_SSR_SPEED_CLASS_10 = $04;
|
Class 10 |
SD SSR AU size value constants
SD_SSR_AU_SIZE_* SD_SSR_AU_SIZE_VALUES:array[0..15] of LongWord = (
| |
0,
|
Not Defined |
$00004000,
|
16 KB |
$00008000,
|
32 KB |
$00010000,
|
64 KB |
$00020000,
|
128 KB |
$00040000,
|
256 KB |
$00080000,
|
512 KB |
$00100000,
|
1 MB |
$00200000,
|
2 MB |
$00400000,
|
4 MB |
$00800000,
|
8 MB |
$00800000 + $00400000,
|
12 MB |
$01000000,
|
16 MB |
$01000000 + $00800000,
|
24 MB |
$02000000,
|
32 MB |
$04000000);
|
64 MB |
SD SSR UHS speed grade value constants
SD_SSR_UHS_SPEED_* SD_SSR_UHS_SPEED_GRADE_0 = 0;
|
Less than 10MB/sec |
SD_SSR_UHS_SPEED_GRADE_1 = 1;
|
10MB/sec and above |
SD SSR UHS AU size value constants
SD_SSR_UHS_AU_SIZE_* SD_SSR_UHS_AU_SIZE_VALUES:array[0..15] of LongWord = (
| |
0,
|
Not Defined |
0,
|
Not Used |
0,
|
Not Used |
0,
|
Not Used |
0,
|
Not Used |
0,
|
Not Used |
0,
|
Not Used |
$00100000,
|
1 MB |
$00200000,
|
2 MB |
$00400000,
|
4 MB |
$00800000,
|
8 MB |
$00800000 + $00400000,
|
12 MB |
$01000000,
|
16 MB |
$01000000 + $00800000,
|
24 MB |
$02000000,
|
32 MB |
$04000000);
|
64 MB |
SD switch status value constants
SD_SWITCH_* | See: Section 4.3.10 of SD Physical Layer Simplified Specification Version 4.10 | |
| SD Switch Fields | |
SD_SWITCH_MAXIMUM_CURRENT = 1;
|
|
SD_SWITCH_GROUP6_SUPPORT = 2;
|
|
SD_SWITCH_GROUP5_SUPPORT = 3;
|
|
SD_SWITCH_GROUP4_SUPPORT = 4;
|
|
SD_SWITCH_GROUP3_SUPPORT = 5;
|
|
SD_SWITCH_GROUP2_SUPPORT = 6;
|
|
SD_SWITCH_GROUP1_SUPPORT = 7;
|
|
SD_SWITCH_GROUP6_SELECTION = 8;
|
|
SD_SWITCH_GROUP5_SELECTION = 9;
|
|
SD_SWITCH_GROUP4_SELECTION = 10;
|
|
SD_SWITCH_GROUP3_SELECTION = 11;
|
|
SD_SWITCH_GROUP2_SELECTION = 12;
|
|
SD_SWITCH_GROUP1_SELECTION = 13;
|
|
SD_SWITCH_STRUCT_VERSION = 14;
|
|
SD_SWITCH_GROUP6_BUSY_STATUS = 15;
|
|
SD_SWITCH_GROUP5_BUSY_STATUS = 16;
|
|
SD_SWITCH_GROUP4_BUSY_STATUS = 17;
|
|
SD_SWITCH_GROUP3_BUSY_STATUS = 18;
|
|
SD_SWITCH_GROUP2_BUSY_STATUS = 19;
|
|
SD_SWITCH_GROUP1_BUSY_STATUS = 20;
|
|
| SD Switch Access Mode (Bus Speed) Support (Group 1) | |
SD_SWITCH_GROUP1_SDR12 = (1 shl 0);
|
|
SD_SWITCH_GROUP1_HS = (1 shl 1);
|
|
SD_SWITCH_GROUP1_SDR25 = (1 shl 1);
|
|
SD_SWITCH_GROUP1_SDR50 = (1 shl 2);
|
|
SD_SWITCH_GROUP1_SDR104 = (1 shl 3);
|
|
SD_SWITCH_GROUP1_DDR50 = (1 shl 4);
|
|
| SD Switch Driver Strength Support (Group 3) | |
SD_SWITCH_GROUP3_TYPE_B = (1 shl 0);
|
|
SD_SWITCH_GROUP3_TYPE_A = (1 shl 1);
|
|
SD_SWITCH_GROUP3_TYPE_C = (1 shl 2);
|
|
SD_SWITCH_GROUP3_TYPE_D = (1 shl 3);
|
|
| SD Switch Structure Versions | |
SD_SWITCH_STRUCT_VER_0 = 0;
|
Bits 511:376 are defined (SD_SWITCH_MAXIMUM_CURRENT to SD_SWITCH_GROUP1_SELECTION) |
SD_SWITCH_STRUCT_VER_1 = 1;
|
Bits 511:272 are defined (SD_SWITCH_MAXIMUM_CURRENT to SD_SWITCH_GROUP1_BUSY_STATUS |
SD SD configuration register (SCR) value constants
SD_SCR_* | See: Section 5.6 of SD Physical Layer Simplified Specification Version 4.10 | |
| SD SCR Fields | |
SD_SCR_STRUCTURE = 1;
|
|
SD_SCR_SD_SPEC = 2;
|
|
SD_SCR_DATA_STAT_AFTER_ERASE = 3;
|
|
SD_SCR_SD_SECURITY = 4;
|
|
SD_SCR_SD_BUS_WIDTHS = 5;
|
|
SD_SCR_SD_SPEC3 = 6;
|
|
SD_SCR_EX_SECURITY = 7;
|
|
SD_SCR_SD_SPEC4 = 8;
|
|
SD_SCR_CMD_SUPPORT = 9;
|
|
SD SCR structure value constants
SD_SCR_STRUCT_* SD_SCR_STRUCT_VER_1_0 = 0;
|
Valid for system specification 1.01 - 4.0 |
SD SCR Spec version value constants
SD_SCR_SPEC_VER_* SD_SCR_SPEC_VER_0 = 0;
|
Implements system specification 1.0 - 1.01 |
SD_SCR_SPEC_VER_1 = 1;
|
Implements system specification 1.10 |
SD_SCR_SPEC_VER_2 = 2;
|
Implements system specification 2.00-4.0X |
SD SCR security value constants
SD_SCR_SECURITY_* SD_SCR_SECURITY_VER_0 = 0;
|
No Security |
SD_SCR_SECURITY_VER_2 = 2;
|
SDSC Card (Security Version 1.01) |
SD_SCR_SECURITY_VER_3 = 3;
|
SDHC Card (Security Version 2.00) |
SD_SCR_SECURITY_VER_4 = 4;
|
SDXC Card (Security Version 3.xx) |
SD SCR bus width value constants
SD_SCR_BUS_WIDTH_* SD_SCR_BUS_WIDTH_1 = (1 shl 0);
|
1 bit (DAT0) |
SD_SCR_BUS_WIDTH_4 = (1 shl 2); {4 bit (DAT0-3)}
|
4 bit (DAT0-3) |
SD SCR extended security value constants
SD_SCR_EX_SECURITY_* SD_SCR_EX_SECURITY_VER_0 = 0;
|
Extended Security is not supported |
SD SCR command support value constants
SD_SCR_*_SUPPORT SD_SCR_CMD20_SUPPORT = (1 shl 0);
|
Mandatory for SDXC card |
SD_SCR_CMD23_SUPPORT = (1 shl 1);
|
Mandatory for UHS104 card |
SD_SCR_CMD48_49_SUPPORT = (1 shl 2);
|
Optional |
SD_SCR_CMD58_59_SUPPORT = (1 shl 3);
|
Optional (If CMD58/59 is supported, CMD48/49 shall be supported) |
SDIO command constants
SDIO_CMD_* | From: /include/linux/mmc/sdio.h | |
SDIO_CMD_SEND_OP_COND = 5;
|
|
SDIO_CMD_RW_DIRECT = 52;
|
|
SDIO_CMD_RW_EXTENDED = 53;
|
|
| SDIO_CMD_RW_DIRECT argument format: | |
[31] R/W flag
|
|
[30:28] Function number
|
|
[27] RAW flag
|
|
[25:9] Register address
|
|
[7:0] Data
|
|
| SDIO_CMD_RW_EXTENDED argument format: | |
[31] R/W flag
|
|
[30:28] Function number
|
|
[27] Block mode
|
|
[26] Increment address
|
|
[25:9] Register address
|
|
[8:0] Byte/block count
|
|
SDIO response value constants
SDIO_RSP_* | From: /include/linux/mmc/sdio.h | |
| R4 | |
SDIO_RSP_R4_18V_PRESENT = (1 shl 24);
|
|
SDIO_RSP_R4_MEMORY_PRESENT = (1 shl 27);
|
|
| R5 | |
SDIO_RSP_R5_COM_CRC_ERROR = (1 shl 15);
|
|
SDIO_RSP_R5_ILLEGAL_COMMAND = (1 shl 14);
|
|
SDIO_RSP_R5_ERROR = (1 shl 11);
|
|
SDIO_RSP_R5_FUNCTION_NUMBER = (1 shl 9);
|
|
SDIO_RSP_R5_OUT_OF_RANGE = (1 shl 8);
|
|
SDIO card common control registers (CCCR) constants
SDIO_CCCR_* SDIO_CCCR_CCCR = $00;
|
|
SDIO_CCCR_SD = $01;
|
|
SDIO_CCCR_IOEx = $02;
|
|
SDIO_CCCR_IORx = $03;
|
|
SDIO_CCCR_IENx = $04;
|
Function/Master Interrupt Enable |
SDIO_CCCR_INTx = $05;
|
Function Interrupt Pending |
SDIO_CCCR_ABORT = $06;
|
function abort/card reset |
SDIO_CCCR_IF = $07;
|
bus interface controls |
SDIO_CCCR_CAPS = $08;
|
|
SDIO_CCCR_CIS = $09;
|
common CIS pointer (3 bytes) |
| Following 4 regs are valid only if SBS is set | |
SDIO_CCCR_SUSPEND = $0c;
|
|
SDIO_CCCR_SELx = $0d;
|
|
SDIO_CCCR_EXECx = $0e;
|
|
SDIO_CCCR_READYx = $0f;
|
|
SDIO_CCCR_BLKSIZE = $10;
|
|
SDIO_CCCR_POWER = $12;
|
|
SDIO_CCCR_SPEED = $13;
|
|
SDIO_CCCR_UHS = $14;
|
|
SDIO_CCCR_DRIVE_STRENGTH = $15;
|
|
SDIO revision constants
SDIO_*_REV_* | SDIO CCCR Register values | |
SDIO_CCCR_REV_1_00 = 0;
|
CCCR/FBR Version 1.00 |
SDIO_CCCR_REV_1_10 = 1;
|
CCCR/FBR Version 1.10 |
SDIO_CCCR_REV_1_20 = 2;
|
CCCR/FBR Version 1.20 |
SDIO_CCCR_REV_3_00 = 3;
|
CCCR/FBR Version 3.00 |
SDIO_SDIO_REV_1_00 = 0;
|
SDIO Spec Version 1.00 |
SDIO_SDIO_REV_1_10 = 1;
|
SDIO Spec Version 1.10 |
SDIO_SDIO_REV_1_20 = 2;
|
SDIO Spec Version 1.20 |
SDIO_SDIO_REV_2_00 = 3;
|
SDIO Spec Version 2.00 |
SDIO_SDIO_REV_3_00 = 4;
|
SDIO Spec Version 3.00 |
| SDIO CCCR SD Register values | |
SDIO_SD_REV_1_01 = 0;
|
SD Physical Spec Version 1.01 |
SDIO_SD_REV_1_10 = 1;
|
SD Physical Spec Version 1.10 |
SDIO_SD_REV_2_00 = 2;
|
SD Physical Spec Version 2.00 |
SDIO_SD_REV_3_00 = 3;
|
SD Physical Spev Version 3.00 |
SDIO bus width constants
SDIO_BUS_* | SDIO CCCR IF Register values | |
SDIO_BUS_WIDTH_MASK = $03;
|
data bus width setting |
SDIO_BUS_WIDTH_1BIT = $00;
|
|
SDIO_BUS_WIDTH_RESERVED = $01;
|
|
SDIO_BUS_WIDTH_4BIT = $02;
|
|
SDIO_BUS_ECSI = $20;
|
Enable continuous SPI interrupt |
SDIO_BUS_SCSI = $40;
|
Support continuous SPI interrupt |
SDIO_BUS_ASYNC_INT = $20;
|
|
SDIO_BUS_CD_DISABLE = $80;
|
disable pull-up on DAT3 (pin 1) |
SDIO CCCR caps register value constants
SDIO_CCCR_CAP_* SDIO_CCCR_CAP_SDC = $01;
|
can do CMD52 while data transfer |
SDIO_CCCR_CAP_SMB = $02;
|
can do multi-block xfers (CMD53) |
SDIO_CCCR_CAP_SRW = $04;
|
supports read-wait protocol |
SDIO_CCCR_CAP_SBS = $08;
|
supports suspend/resume |
SDIO_CCCR_CAP_S4MI = $10;
|
interrupt during 4-bit CMD53 |
SDIO_CCCR_CAP_E4MI = $20;
|
enable ints during 4-bit CMD53 |
SDIO_CCCR_CAP_LSC = $40;
|
low speed card |
SDIO_CCCR_CAP_4BLS = $80;
|
4 bit low speed card |
SDIO CCCR power register value constants
SDIO_POWER_* SDIO_POWER_SMPC = $01;
|
Supports Master Power Control |
SDIO_POWER_EMPC = $02;
|
Enable Master Power Control |
SDIO CCCR speed register value constants
SDIO_SPEED_* SDIO_SPEED_SHS = $01;
|
Supports High-Speed mode |
SDIO_SPEED_BSS_SHIFT = 1;
|
|
SDIO_SPEED_BSS_MASK = (7 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_SDR12 = (0 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_SDR25 = (1 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_SDR50 = (2 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_SDR104 = (3 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_DDR50 = (4 shl SDIO_SPEED_BSS_SHIFT);
|
|
SDIO_SPEED_EHS = SDIO_SPEED_SDR25;
|
Enable High-Speed |
SDIO CCCR UHS register value constants
SDIO_UHS_* SDIO_UHS_SDR50 = $01;
|
|
SDIO_UHS_SDR104 = $02;
|
|
SDIO_UHS_DDR50 = $04;
|
SDIO CCCR drive strength register value constants
SDIO_DRIVE_* SDIO_SDTx_MASK = $07;
|
|
SDIO_DRIVE_SDTA = (1 shl 0);
|
|
SDIO_DRIVE_SDTC = (1 shl 1);
|
|
SDIO_DRIVE_SDTD = (1 shl 2);
|
|
SDIO_DRIVE_DTSx_MASK = $03;
|
|
SDIO_DRIVE_DTSx_SHIFT = 4;
|
|
SDIO_DTSx_SET_TYPE_B = (0 shl SDIO_DRIVE_DTSx_SHIFT);
|
|
SDIO_DTSx_SET_TYPE_A = (1 shl SDIO_DRIVE_DTSx_SHIFT);
|
|
SDIO_DTSx_SET_TYPE_C = (2 shl SDIO_DRIVE_DTSx_SHIFT);
|
|
SDIO_DTSx_SET_TYPE_D = (3 shl SDIO_DRIVE_DTSx_SHIFT);
|
SDIO function basic register (FBR) constants
SDIO_FBR_* SDIO_FBR_BASE(f) ((f) * $100)
|
base of function f's FBRs |
SDIO_FBR_STD_IF = $00;
|
|
SDIO_FBR_STD_IF_EXT = $01;
|
|
SDIO_FBR_POWER = $02;
|
|
SDIO_FBR_CIS = $09;
|
CIS pointer (3 bytes) |
SDIO_FBR_CSA = $0C;
|
CSA pointer (3 bytes) |
SDIO_FBR_BLKSIZE = $10;
|
block size (2 bytes) |
| SDIO FBR IF Register values | |
SDIO_FBR_SUPPORTS_CSA = $40;
|
supports Code Storage Area |
SDIO_FBR_ENABLE_CSA = $80;
|
enable Code Storage Area |
| SDIO FBR POWER Register values | |
SDIO_FBR_POWER_SPS = $01;
|
Supports Power Selection |
SDIO_FBR_POWER_EPS = $02;
|
Enable (low) Power Selection |
SDHCI specific constants
SDHCI_* SDHCI_NAME_PREFIX = 'SDHCI';
|
Name prefix for SDHCI Devices |
SDHCI host type constants
SDHCI_TYPE_* SDHCI_TYPE_NONE = 0;
|
|
SDHCI_TYPE_MAX = 0;
|
|
| SDHCI Type Names | |
SDHCI_TYPE_NAMES:array[SDHCI_TYPE_NONE..SDHCI_TYPE_MAX] of String = (
| |
'SDHCI_TYPE_NONE');
|
|
SDHCI host state constants
SDHCI_STATE_* SDHCI_STATE_DISABLED = 0;
|
|
SDHCI_STATE_ENABLED = 1;
|
|
SDHCI_STATE_MAX = 1;
|
|
| SDHCI State Names | |
SDHCI_STATE_NAMES:array[SDHCI_STATE_DISABLED..SDHCI_STATE_MAX] of String = (
| |
'SDHCI_STATE_DISABLED',
|
|
'SDHCI_STATE_ENABLED');
|
|
SDHCI host flag constants
SDHCI_FLAG_* SDHCI_FLAG_NONE = $00000000;
|
|
SDHCI_FLAG_SDMA = $00000001;
|
|
SDHCI_FLAG_ADMA = $00000002;
|
|
SDHCI_FLAG_SPI = $00000004;
|
|
SDHCI_FLAG_CRC_ENABLE = $00000008;
|
SDHCI controller register constants
SDHCI_DMA_*, SDHCI_BLOCK_* SDHCI_DMA_ADDRESS = $00;
|
|
SDHCI_BLOCK_SIZE = $04;
|
|
SDHCI_BLOCK_COUNT = $06;
|
|
SDHCI_ARGUMENT = $08;
|
|
SDHCI_TRANSFER_MODE = $0C;
|
|
SDHCI_COMMAND = $0E;
|
|
SDHCI_RESPONSE = $10;
|
|
SDHCI_BUFFER = $20;
|
|
SDHCI_PRESENT_STATE = $24;
|
|
SDHCI_HOST_CONTROL = $28;
|
|
SDHCI_POWER_CONTROL = $29;
|
|
SDHCI_BLOCK_GAP_CONTROL = $2A;
|
|
SDHCI_WAKE_UP_CONTROL = $2B;
|
|
SDHCI_CLOCK_CONTROL = $2C;
|
|
SDHCI_TIMEOUT_CONTROL = $2E;
|
|
SDHCI_SOFTWARE_RESET = $2F;
|
|
SDHCI_INT_STATUS = $30;
|
|
SDHCI_INT_ENABLE = $34;
|
|
SDHCI_SIGNAL_ENABLE = $38;
|
|
SDHCI_ACMD12_ERR = $3C;
|
|
| 3E-3F reserved | |
SDHCI_CAPABILITIES = $40;
|
|
SDHCI_CAPABILITIES_1 = $44;
|
|
SDHCI_MAX_CURRENT = $48;
|
|
| 4C-4F reserved for more max current | |
SDHCI_SET_ACMD12_ERROR = $50;
|
|
SDHCI_SET_INT_ERROR = $52;
|
|
SDHCI_ADMA_ERROR = $54;
|
|
| 55-57 reserved | |
SDHCI_ADMA_ADDRESS = $58;
|
|
| 60-FB reserved | |
SDHCI_SLOT_INT_STATUS = $FC;
|
|
SDHCI_HOST_VERSION = $FE;
|
|
SDHCI transfer mode constants
SDHCI_TRNS_* SDHCI_TRNS_DMA = $01;
|
|
SDHCI_TRNS_BLK_CNT_EN = $02;
|
|
SDHCI_TRNS_AUTO_CMD12 = $04;
|
SDHCI_TRNS_ACMD12 |
SDHCI_TRNS_AUTO_CMD23 = $08;
|
|
SDHCI_TRNS_READ = $10;
|
|
SDHCI_TRNS_MULTI = $20;
|
SDHCI command value constants
SDHCI_CMD_* SDHCI_CMD_RESP_MASK = $03;
|
|
SDHCI_CMD_CRC = $08;
|
|
SDHCI_CMD_INDEX = $10;
|
|
SDHCI_CMD_DATA = $20;
|
|
SDHCI_CMD_ABORTCMD = $C0;
|
SDHCI command response value constants
SDHCI_CMD_RESP_* SDHCI_CMD_RESP_NONE = $00;
|
|
SDHCI_CMD_RESP_LONG = $01;
|
|
SDHCI_CMD_RESP_SHORT = $02;
|
|
SDHCI_CMD_RESP_SHORT_BUSY = $03;
|
SDHCI present state value constants
SDHCI_DATA_*, SDHCI_CARD_* SDHCI_CMD_INHIBIT = $00000001;
|
|
SDHCI_DATA_INHIBIT = $00000002;
|
|
SDHCI_DOING_WRITE = $00000100;
|
|
SDHCI_DOING_READ = $00000200;
|
|
SDHCI_SPACE_AVAILABLE = $00000400;
|
|
SDHCI_DATA_AVAILABLE = $00000800;
|
|
SDHCI_CARD_PRESENT = $00010000;
|
|
SDHCI_CARD_STATE_STABLE = $00020000;
|
|
SDHCI_CARD_DETECT_PIN_LEVEL = $00040000;
|
|
SDHCI_WRITE_PROTECT = $00080000;
|
Set if Write Enabled / Clear if Write Protected |
SDHCI host control value constants
SDHCI_CTRL_* SDHCI_CTRL_LED = $01;
|
|
SDHCI_CTRL_4BITBUS = $02;
|
|
SDHCI_CTRL_HISPD = $04;
|
|
SDHCI_CTRL_DMA_MASK = $18;
|
|
SDHCI_CTRL_SDMA = $00;
|
|
SDHCI_CTRL_ADMA1 = $08;
|
|
SDHCI_CTRL_ADMA32 = $10;
|
|
SDHCI_CTRL_ADMA64 = $18;
|
|
SDHCI_CTRL_8BITBUS = $20;
|
|
SDHCI_CTRL_CD_TEST_INS = $40;
|
|
SDHCI_CTRL_CD_TEST = $80;
|
SDHCI power control value constants
SDHCI_POWER_* SDHCI_POWER_ON = $01;
|
|
SDHCI_POWER_180 = $0A;
|
|
SDHCI_POWER_300 = $0C;
|
|
SDHCI_POWER_330 = $0E;
|
SDHCI wakeup control value constants
SDHCI_WAKE_* SDHCI_WAKE_ON_INT = $01;
|
|
SDHCI_WAKE_ON_INSERT = $02;
|
|
SDHCI_WAKE_ON_REMOVE = $04;
|
SDHCI clock control value constants
SDHCI_CLOCK_* SDHCI_DIVIDER_SHIFT = 8;
|
|
SDHCI_DIVIDER_HI_SHIFT = 6;
|
|
SDHCI_DIV_MASK = $FF;
|
|
SDHCI_DIV_MASK_LEN = 8;
|
|
SDHCI_DIV_HI_MASK = $0300;
|
|
SDHCI_CLOCK_CARD_EN = $0004;
|
|
SDHCI_CLOCK_INT_STABLE = $0002;
|
|
SDHCI_CLOCK_INT_EN = $0001;
|
SDHCI software reset value constants
SDHCI_RESET_* SDHCI_RESET_ALL = $01;
|
|
SDHCI_RESET_CMD = $02;
|
|
SDHCI_RESET_DATA = $04;
|
SDHCI interrupt value constants
SDHCI_INT_* SDHCI_INT_RESPONSE = $00000001;
|
|
SDHCI_INT_DATA_END = $00000002;
|
|
SDHCI_INT_BLK_GAP = $00000004;
|
|
SDHCI_INT_DMA_END = $00000008;
|
|
SDHCI_INT_SPACE_AVAIL = $00000010;
|
|
SDHCI_INT_DATA_AVAIL = $00000020;
|
|
SDHCI_INT_CARD_INSERT = $00000040;
|
|
SDHCI_INT_CARD_REMOVE = $00000080;
|
|
SDHCI_INT_CARD_INT = $00000100;
|
|
SDHCI_INT_ERROR = $00008000;
|
|
SDHCI_INT_TIMEOUT = $00010000;
|
|
SDHCI_INT_CRC = $00020000;
|
|
SDHCI_INT_END_BIT = $00040000;
|
|
SDHCI_INT_INDEX = $00080000;
|
|
SDHCI_INT_DATA_TIMEOUT = $00100000;
|
|
SDHCI_INT_DATA_CRC = $00200000;
|
|
SDHCI_INT_DATA_END_BIT = $00400000;
|
|
SDHCI_INT_BUS_POWER = $00800000;
|
|
SDHCI_INT_ACMD12ERR = $01000000;
|
|
SDHCI_INT_ADMA_ERROR = $02000000;
|
|
SDHCI_INT_NORMAL_MASK = $00007FFF;
|
|
SDHCI_INT_ERROR_MASK = $FFFF8000;
|
|
SDHCI_INT_CMD_MASK = (SDHCI_INT_RESPONSE or SDHCI_INT_TIMEOUT or SDHCI_INT_CRC or SDHCI_INT_END_BIT or SDHCI_INT_INDEX);
| |
SDHCI_INT_DATA_MASK = (SDHCI_INT_DATA_END or SDHCI_INT_DMA_END or SDHCI_INT_DATA_AVAIL or SDHCI_INT_SPACE_AVAIL or SDHCI_INT_DATA_TIMEOUT or SDHCI_INT_DATA_CRC or SDHCI_INT_DATA_END_BIT or SDHCI_INT_ADMA_ERROR or SDHCI_INT_BLK_GAP);
| |
SDHCI_INT_ALL_MASK = (LongWord(-1));
|
|
SDHCI capabilities value constants
SDHCI_*_MASK*, SDHCI_*SHIFT SDHCI_TIMEOUT_CLK_MASK = $0000003F;
|
|
SDHCI_TIMEOUT_CLK_SHIFT = 0;
|
|
SDHCI_TIMEOUT_CLK_UNIT = $00000080;
|
|
SDHCI_CLOCK_BASE_MASK = $00003F00;
|
|
SDHCI_CLOCK_V3_BASE_MASK = $0000FF00;
|
|
SDHCI_CLOCK_BASE_SHIFT = 8;
|
|
SDHCI_CLOCK_BASE_MULTIPLIER = 1000000;
|
|
SDHCI_MAX_BLOCK_MASK = $00030000;
|
|
SDHCI_MAX_BLOCK_SHIFT = 16;
|
|
SDHCI_CAN_DO_8BIT = $00040000;
|
|
SDHCI_CAN_DO_ADMA2 = $00080000;
|
|
SDHCI_CAN_DO_ADMA1 = $00100000;
|
|
SDHCI_CAN_DO_HISPD = $00200000;
|
|
SDHCI_CAN_DO_SDMA = $00400000;
|
|
SDHCI_CAN_VDD_330 = $01000000;
|
|
SDHCI_CAN_VDD_300 = $02000000;
|
|
SDHCI_CAN_VDD_180 = $04000000;
|
|
SDHCI_CAN_64BIT = $10000000;
|
|
NAME_
|
|
NAME_
|
|
NAME_
|
|
NAME_
|
SDHCI host version value constants
SDHCI_*_VER_* SDHCI_VENDOR_VER_MASK = $FF00;
|
|
SDHCI_VENDOR_VER_SHIFT = 8;
|
|
SDHCI_SPEC_VER_MASK = $00FF;
|
|
SDHCI_SPEC_VER_SHIFT = 0;
|
|
SDHCI_SPEC_100 = 0;
|
|
SDHCI_SPEC_200 = 1;
|
|
SDHCI_SPEC_300 = 2;
|
SDHCI clock divider constants
SDHCI_MAX_CLOCK_DIV_* SDHCI_MAX_CLOCK_DIV_SPEC_200 = 256;
|
|
SDHCI_MAX_CLOCK_DIV_SPEC_300 = 2046;
|
SDHCI quirks/bug constants
SDHCI_QUIRK* | From: U-Boot sdhci.h | |
*SDHCI_QUIRK_32BIT_DMA_ADDR = (1 shl 0);
|
See: SDHCI_QUIRK_32BIT_DMA_ADDR below |
SDHCI_QUIRK_REG32_RW = (1 shl 1);
|
|
SDHCI_QUIRK_BROKEN_R1B = (1 shl 2);
|
|
SDHCI_QUIRK_NO_HISPD_BIT = (1 shl 3);
|
See: SDHCI_QUIRK_NO_HISPD_BIT below |
SDHCI_QUIRK_BROKEN_VOLTAGE = (1 shl 4);
|
Use SDHCI_QUIRK_MISSING_CAPS instead |
SDHCI_QUIRK_NO_CD = (1 shl 5);
|
See: SDHCI_QUIRK_BROKEN_CARD_DETECTION below |
SDHCI_QUIRK_WAIT_SEND_CMD = (1 shl 6);
|
|
SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER = (1 shl 7);
|
See: SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER below |
SDHCI_QUIRK_USE_WIDE8 = (1 shl 8);
|
|
SDHCI_QUIRK_MISSING_CAPS = (1 shl 9);
|
See: SDHCI_QUIRK_MISSING_CAPS below* |
| From Linux /include/linux/mmc/sdhci.h | |
SDHCI_QUIRK_CLOCK_BEFORE_RESET = (1 shl 0);
|
Controller doesn't honor resets unless we touch the clock register |
SDHCI_QUIRK_FORCE_DMA = (1 shl 1);
|
Controller has bad caps bits, but really supports DMA |
SDHCI_QUIRK_NO_CARD_NO_RESET = (1 shl 2);
|
Controller doesn't like to be reset when there is no card inserted |
SDHCI_QUIRK_SINGLE_POWER_WRITE = (1 shl 3);
|
Controller doesn't like clearing the power reg before a change |
SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS = (1 shl 4);
|
Controller has flaky internal state so reset it on each ios change |
SDHCI_QUIRK_BROKEN_DMA = (1 shl 5);
|
Controller has an unusable DMA engine |
SDHCI_QUIRK_BROKEN_ADMA = (1 shl 6);
|
Controller has an unusable ADMA engine |
SDHCI_QUIRK_32BIT_DMA_ADDR = (1 shl 7);
|
Controller can only DMA from 32-bit aligned addresses |
SDHCI_QUIRK_32BIT_DMA_SIZE = (1 shl 8);
|
Controller can only DMA chunk sizes that are a multiple of 32 bits |
SDHCI_QUIRK_32BIT_ADMA_SIZE = (1 shl 9);
|
Controller can only ADMA chunks that are a multiple of 32 bits |
SDHCI_QUIRK_RESET_AFTER_REQUEST = (1 shl 10);
|
Controller needs to be reset after each request to stay stable |
SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER = (1 shl 11);
|
Controller needs voltage and power writes to happen separately |
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL = (1 shl 12);
|
Controller provides an incorrect timeout value for transfers |
SDHCI_QUIRK_BROKEN_SMALL_PIO = (1 shl 13);
|
Controller has an issue with buffer bits for small transfers |
SDHCI_QUIRK_NO_BUSY_IRQ = (1 shl 14);
|
Controller does not provide transfer-complete interrupt when not busy |
SDHCI_QUIRK_BROKEN_CARD_DETECTION = (1 shl 15);
|
Controller has unreliable card detection |
SDHCI_QUIRK_INVERTED_WRITE_PROTECT = (1 shl 16);
|
Controller reports inverted write-protect state |
SDHCI_QUIRK_PIO_NEEDS_DELAY = (1 shl 18);
|
Controller does not like fast PIO transfers |
SDHCI_QUIRK_FORCE_BLK_SZ_2048 = (1 shl 20);
|
Controller has to be forced to use block size of 2048 bytes |
SDHCI_QUIRK_NO_MULTIBLOCK = (1 shl 21);
|
Controller cannot do multi-block transfers |
SDHCI_QUIRK_FORCE_1_BIT_DATA = (1 shl 22);
|
Controller can only handle 1-bit data transfers |
SDHCI_QUIRK_DELAY_AFTER_POWER = (1 shl 23);
|
Controller needs 10ms delay between applying power and clock |
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK = (1 shl 24);
|
Controller uses SDCLK instead of TMCLK for data timeouts |
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN = (1 shl 25);
|
Controller reports wrong base clock capability |
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC = (1 shl 26);
|
Controller cannot support End Attribute in NOP ADMA descriptor |
SDHCI_QUIRK_MISSING_CAPS = (1 shl 27);
|
Controller is missing device caps. Use caps provided by host |
SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 = (1 shl 28);
|
Controller uses Auto CMD12 command to stop the transfer |
SDHCI_QUIRK_NO_HISPD_BIT = (1 shl 29);
|
Controller doesn't have HISPD bit field in HI-SPEED SD card |
SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC = (1 shl 30);
|
Controller treats ADMA descriptors with length 0000h incorrectly |
SDHCI_QUIRK_UNSTABLE_RO_DETECT = (1 shl 31);
|
The read-only detection via SDHCI_PRESENT_STATE register is unstable |
| SDHCI More Quirks/Bugs | |
| From Linux /include/linux/mmc/sdhci.h | |
SDHCI_QUIRK2_HOST_OFF_CARD_ON = (1 shl 0);
|
|
SDHCI_QUIRK2_HOST_NO_CMD23 = (1 shl 1);
|
|
SDHCI_QUIRK2_NO_1_8_V = (1 shl 2);
|
The system physically doesn't support 1.8v, even if the host does |
SDHCI_QUIRK2_PRESET_VALUE_BROKEN = (1 shl 3);
|
|
SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON = (1 shl 4);
|
|
SDHCI_QUIRK2_BROKEN_HOST_CONTROL = (1 shl 5);
|
Controller has a non-standard host control register |
SDHCI_QUIRK2_BROKEN_HS200 = (1 shl 6);
|
Controller does not support HS200 |
SDHCI_QUIRK2_BROKEN_DDR50 = (1 shl 7);
|
Controller does not support DDR50 |
SDHCI_QUIRK2_STOP_WITH_TC = (1 shl 8);
|
Stop command(CMD12) can set Transfer Complete when not using MMC_RSP_BUSY |
| Additions from U-Boot | |
SDHCI_QUIRK2_REG32_RW = (1 shl 28);
|
Controller requires all register reads and writes as 32bit |
SDHCI_QUIRK2_BROKEN_R1B = (1 shl 29);
|
Response type R1B is broken |
SDHCI_QUIRK2_WAIT_SEND_CMD = (1 shl 30);
|
Controller requires a delay between each command write |
SDHCI_QUIRK2_USE_WIDE8 = (1 shl 31);
|
|
SDHCI host SDMA buffer boundary constants
SDHCI_DEFAULT_BOUNDARY_* | Valid values from 4K to 512K in powers of 2 | |
SDHCI_DEFAULT_BOUNDARY_SIZE = (512 * 1024);
|
|
SDHCI_DEFAULT_BOUNDARY_ARG = (7);
|
|
SDHCI timeout value constants
SDHCI_TIMEOUT_VALUE* SDHCI_TIMEOUT_VALUE = $0E;
|
Type definitions
To be documented
Public variables
To be documented
Function declarations
Initialization functions
procedure MMCInit;
Description: To be documented
| Note | None documented |
|---|
function MMCStart:LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCStop:LongWord;
Description: To be documented
| Note | None documented |
|---|
procedure MMCAsyncStart(SDHCI:PSDHCIHost);
Description: To be documented
| Note | None documented |
|---|
MMC functions
function MMCDeviceReadBlocks(MMC:PMMCDevice; const Start,Count:Int64; Buffer:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceWriteBlocks(MMC:PMMCDevice; const Start,Count:Int64; Buffer:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceEraseBlocks(MMC:PMMCDevice; const Start,Count:Int64):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceGoIdle(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetClock(MMC:PMMCDevice; Clock:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetBusWidth(MMC:PMMCDevice; Width:LongWord):LongWord;
Description: To be documented
| Reference | Section 3.4 of SD Host Controller Simplified Specification V3.0 partA2_300.pdf |
|---|
function MMCDeviceSetBlockLength(MMC:PMMCDevice; Length:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetBlockCount(MMC:PMMCDevice; Count:LongWord; Relative:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetDriverStage(MMC:PMMCDevice; DriverStage:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSelectCard(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceDeselectCard(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSwitch(MMC:PMMCDevice; Setting,Index,Value:Byte):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendCardStatus(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendOperationCondition(MMC:PMMCDevice; Probe:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendCardSpecific(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceDecodeCardSpecific(MMC:PMMCDevice):LongWord;
Description: Given a 128-bit response, decode to our card CSD structure
| Note | None documented |
|---|
function MMCDeviceSendCardIdentification(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendAllCardIdentification(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceDecodeCardIdentification(MMC:PMMCDevice):LongWord;
Description: Given a 128-bit response, decode to our card CID structure
| Note | None documented |
|---|
function MMCDeviceGetExtendedCardSpecific(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendExtendedCardSpecific(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceDecodeExtendedCardSpecific(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetRelativeAddress(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSPISetCRC(MMC:PMMCDevice; Enable:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSPIReadOperationCondition(MMC:PMMCDevice; HighCapacity:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceInsert(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceRemove(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceInitialize(MMC:PMMCDevice):LongWord;
Description: To be documented
| Reference | Section 3.6 of SD Host Controller Simplified Specification V3.0 partA2_300.pdf |
|---|
function MMCDeviceDeinitialize(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceGetCardDetect(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceGetWriteProtect(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSendCommand(MMC:PMMCDevice; Command:PMMCCommand):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceSetIOS(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceCreate:PMMCDevice;
Description: Create a new MMC entry
| Return | Pointer to new MMC entry or nil if MMC could not be created |
|---|
function MMCDeviceCreateEx(Size:LongWord):PMMCDevice;
Description: Create a new MMC entry
| Size | Size in bytes to allocate for new MMC (Including the MMC entry) |
|---|---|
| Return | Pointer to new MMC entry or nil if MMC could not be created |
function MMCDeviceDestroy(MMC:PMMCDevice):LongWord;
Description: Destroy an existing MMC entry
| Note | None documented |
|---|
function MMCDeviceRegister(MMC:PMMCDevice):LongWord;
Description: Register a new MMC in the MMC table
| Note | None documented |
|---|
function MMCDeviceDeregister(MMC:PMMCDevice):LongWord;
Description: Deregister a MMC from the MMC table
| Note | None documented |
|---|
function MMCDeviceFind(MMCId:LongWord):PMMCDevice;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceFindByName(const Name:String):PMMCDevice; inline;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceFindByDescription(const Description:String):PMMCDevice; inline;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceEnumerate(Callback:TMMCEnumerate; Data:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceNotification(MMC:PMMCDevice; Callback:TMMCNotification; Data:Pointer; Notification,Flags:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
SD functions
function SDDeviceSwitch(MMC:PMMCDevice; Mode,Group:Integer; Value:Byte; Buffer:Pointer):LongWord;
Description: To be documented
| Buffer | Buffer must point to a 64 byte buffer for Switch Status information |
|---|---|
| Note | See 4.3.10 of SD Physical Layer Simplified Specification V4.10 |
function SDDeviceSwitchHighspeed(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceSetBusSpeed(MMC:PMMCDevice; Speed:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceSetBusWidth(MMC:PMMCDevice; Width:LongWord):LongWord;
Description: To be documented
| Note | See Table 4-30 in Section 4.7.4 of SD Physical Layer Simplified Specification V4.10 |
|---|
function SDDeviceSendInterfaceCondition(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | See 4.3.13 of SD Physical Layer Simplified Specification V4.10. CMD8 (SEND_IF_COND) must be invoked to support SD 2.0 cards. The card must be in Idle State before issuing this command. This command will fail harmlessly for SD 1.0 cards. |
|---|
function SDDeviceSendOperationCondition(MMC:PMMCDevice; Probe:Boolean):LongWord;
Description: To be documented
| Note | See 4.2.3.1 of SD Physical Layer Simplified Specification V4.10 |
|---|
function SDDeviceGetCardSpecific(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceDecodeCardSpecific(MMC:PMMCDevice):LongWord;
Description: Given a 128-bit response, decode to our card CSD structure
| Note | None documented |
|---|
function SDDeviceGetCardIdentification(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceDecodeCardIdentification(MMC:PMMCDevice):LongWord;
Description: Given a 128-bit response, decode to our card CID structure
| Note | None documented |
|---|
function SDDeviceSendSDStatus(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceDecodeSDStatus(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceSendSDSwitch(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceDecodeSDSwitch(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceSendSDConfiguration(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceDecodeSDConfiguration(MMC:PMMCDevice):LongWord;
Description: Given a 64-bit response, decode to our card SCR structure
| Note | None documented |
|---|
function SDDeviceSendRelativeAddress(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDDeviceSendApplicationCommand(MMC:PMMCDevice; Command:PMMCCommand):LongWord;
Description: To be documented
| Note | None documented |
|---|
SDIO functions
function SDIODeviceReset(MMC:PMMCDevice):LongWord;
Description: To be documented
| Note | See SDIO Simplified Specification V2.0, 4.4 Reset for SDIO |
|---|
function SDIODeviceSendOperationCondition(MMC:PMMCDevice; Probe:Boolean):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDIODeviceReadWriteDirect(MMC:PMMCDevice; Write:Boolean; Operation,Address:LongWord; Input:Byte; Output:PByte):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDIODeviceReadWriteExtended(MMC:PMMCDevice; Write:Boolean; Operation,Address:LongWord; Increment:Boolean; Buffer:Pointer; BlockCount,BlockSize:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
SDHCI functions
function SDHCIHostReset(SDHCI:PSDHCIHost; Mask:Byte):LongWord;
Description: To be documented
| Reference | Section 3.3 of SD Host Controller Simplified Specification V3.0 partA2_300.pdf |
|---|
function SDHCIHostSetPower(SDHCI:PSDHCIHost; Power:Word):LongWord;
Description: To be documented
| Reference | Section 3.3 of SD Host Controller Simplified Specification V3.0 partA2_300.pdf |
|---|
function SDHCIHostSetClock(SDHCI:PSDHCIHost; Clock:LongWord):LongWord;
Description: To be documented
| Reference | Section 3.2 of SD Host Controller Simplified Specification V3.0 partA2_300.pdf |
|---|
function SDHCIHostTransferPIO(SDHCI:PSDHCIHost):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostTransferDMA(SDHCI:PSDHCIHost):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostFinishCommand(SDHCI:PSDHCIHost):LongWord;
Description: Called by Interrupt Command handler when an SDHCI_INT_RESPONSE is received
| Note | None documented |
|---|
function SDHCIHostFinishData(SDHCI:PSDHCIHost):LongWord;
Description: Called by Interrupt Data handler when data is received
| Note | None documented |
|---|
function SDHCIHostCommandInterrupt(SDHCI:PSDHCIHost; InterruptMask:LongWord; var ReturnMask:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostDataInterrupt(SDHCI:PSDHCIHost; InterruptMask:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostStart(SDHCI:PSDHCIHost):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostStop(SDHCI:PSDHCIHost):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostReadByte(SDHCI:PSDHCIHost; Reg:LongWord):Byte; inline;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostReadWord(SDHCI:PSDHCIHost; Reg:LongWord):Word; inline;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostReadLong(SDHCI:PSDHCIHost; Reg:LongWord):LongWord; inline;
Description: To be documented
| Note | None documented |
|---|
procedure SDHCIHostWriteByte(SDHCI:PSDHCIHost; Reg:LongWord; Value:Byte); inline;
Description: To be documented
| Note | None documented |
|---|
procedure SDHCIHostWriteWord(SDHCI:PSDHCIHost; Reg:LongWord; Value:Word); inline;
Description: To be documented
| Note | None documented |
|---|
procedure SDHCIHostWriteLong(SDHCI:PSDHCIHost; Reg:LongWord; Value:LongWord); inline;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostSetClockDivider(SDHCI:PSDHCIHost; Index:Integer; Divider:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostSetControlRegister(SDHCI:PSDHCIHost):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostCreate:PSDHCIHost;
Description: Create a new SDHCI entry
| Return | Pointer to new SDHCI entry or nil if SDHCI could not be created |
|---|
function SDHCIHostCreateEx(Size:LongWord):PSDHCIHost;
Description: Create a new SDHCI entry
| Size | Size in bytes to allocate for new SDHCI (Including the SDHCI entry) |
|---|---|
| Return | Pointer to new SDHCI entry or nil if SDHCI could not be created |
function SDHCIHostDestroy(SDHCI:PSDHCIHost):LongWord;
Description: Destroy an existing SDHCI entry
| Note | None documented |
|---|
function SDHCIHostRegister(SDHCI:PSDHCIHost):LongWord;
Description: Register a new SDHCI in the SDHCI table
| Note | None documented |
|---|
function SDHCIHostDeregister(SDHCI:PSDHCIHost):LongWord;
Description: Deregister a SDHCI from the SDHCI table
| Note | None documented |
|---|
function SDHCIHostFind(SDHCIId:LongWord):PSDHCIHost;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostEnumerate(Callback:TSDHCIEnumerate; Data:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function SDHCIHostNotification(SDHCI:PSDHCIHost; Callback:TSDHCINotification; Data:Pointer; Notification,Flags:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
MMC helper functions
function MMCGetCount:LongWord; inline;
Description: Get the current MMC count
| Note | None documented |
|---|
function MMCDeviceCheck(MMC:PMMCDevice):PMMCDevice;
Description: Check if the supplied MMC is in the MMC table
| Note | None documented |
|---|
function MMCIsSD(MMC:PMMCDevice):Boolean;
Description: To be documented
| Note | None documented |
|---|
function MMCGetCIDValue(MMC:PMMCDevice; Version,Value:LongWord):LongWord;
Description: Extract a CID field value from the 128 bit Card Identification register
| Note | None documented |
|---|
function MMCGetCSDValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract a CSD field value from the 128 bit Card Specific register
| Note | None documented |
|---|
function MMCGetExtendedCSDValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract an Extended CSD field value from the 512 byte Extended Card Specific register
| Note | None documented |
|---|
function MMCExtractBits(Buffer:Pointer; Start,Size:LongWord):LongWord;
Description: To be documented
| Start | Start is the starting bit to extract |
|---|---|
| Size | Size is the number of bits to extract |
| Note | Start is the LSB so to extract 8 bits from 127 to 120 then Start would be 120 and Size would be 8 |
function MMCExtractBitsEx(Buffer:Pointer; Length,Start,Size:LongWord):LongWord;
Description: To be documented
| Length | Length is the size of the buffer in LongWords |
|---|---|
| Start | Start is the starting bit to extract |
| Size | Size is the number of bits to extract |
| Note | Start is the LSB so to extract 8 bits from 127 to 120 then Start would be 120 and Size would be 8. For a 128 bit buffer (16 bytes) Length would be 4. For a 512 bit buffer (64 bytes) Length would be 16. |
function MMCIsMultiCommand(Command:Word):Boolean;
Description: To be documented
| Note | None documented |
|---|
function MMCStatusToString(Status:LongWord):String;
Description: Translates an MMC status code into a string describing it
| Note | None documented |
|---|
function MMCDeviceTypeToString(MMCType:LongWord):String;
Description: To be documented
| Note | None documented |
|---|
function MMCDeviceStateToString(MMCState:LongWord):String;
Description: To be documented
| Note | None documented |
|---|
procedure MMCLog(Level:LongWord; MMC:PMMCDevice; const AText:String);
Description: To be documented
| Note | None documented |
|---|
procedure MMCLogInfo(MMC:PMMCDevice; const AText:String);
Description: To be documented
| Note | None documented |
|---|
procedure MMCLogError(MMC:PMMCDevice; const AText:String);
Description: To be documented
| Note | None documented |
|---|
procedure MMCLogDebug(MMC:PMMCDevice; const AText:String);
Description: To be documented
| Note | None documented |
|---|
SD helper functions
function SDGetMaxClock(MMC:PMMCDevice):LongWord;
Description: Determine the Maximum Clock (DTR) for the current card
| Note | None documented |
|---|
function SDGetCIDValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract a CID field value from the 128 bit Card Identification register
| Note | None documented |
|---|
function SDGetCSDValue(MMC:PMMCDevice; Version,Value:LongWord):LongWord;
Description: Extract a CSD field value from the 128 bit Card Specific register
| Note | None documented |
|---|
function SDGetSCRValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract an SCR field value from the 64 bit SD Configuration register
| Note | None documented |
|---|
function SDGetSSRValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract an SCR field value from the 512 bit SD Status register
| Note | None documented |
|---|
function SDGetSwitchValue(MMC:PMMCDevice; Value:LongWord):LongWord;
Description: Extract a Switch field value from the 512 bit SD Switch status
| Note | None documented |
|---|
SDHCI helper functions
function SDHCIGetCount:LongWord; inline;
Description: Get the current SDHCI count
| Note | None documented |
|---|
function SDHCIHostCheck(SDHCI:PSDHCIHost):PSDHCIHost;
Description: Check if the supplied SDHCI is in the SDHCI table
| Note | None documented |
|---|
function SDHCIIsSPI(SDHCI:PSDHCIHost):Boolean;
Description: To be documented
| Note | None documented |
|---|
function SDHCIGetVersion(SDHCI:PSDHCIHost):Word;
Description: To be documented
| Note | None documented |
|---|
function SDHCIGetCommand(Command:Word):Word;
Description: To be documented
| Note | None documented |
|---|
function SDHCIMakeCommand(Command,Flags:Word):Word;
Description: To be documented
| Note | None documented |
|---|
function SDHCIMakeBlockSize(DMA,BlockSize:Word):Word;
Description: To be documented
| Note | None documented |
|---|
function SDHCIDeviceTypeToString(SDHCIType:LongWord):String;
Description: To be documented
| Note | None documented |
|---|
function SDHCIDeviceStateToString(SDHCIState:LongWord):String;
Description: To be documented
| Note | None documented |
|---|
MMC storage functions
function MMCStorageDeviceRead(Storage:PStorageDevice; const Start,Count:Int64; Buffer:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCStorageDeviceWrite(Storage:PStorageDevice; const Start,Count:Int64; Buffer:Pointer):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCStorageDeviceErase(Storage:PStorageDevice; const Start,Count:Int64):LongWord;
Description: To be documented
| Note | None documented |
|---|
function MMCStorageDeviceControl(Storage:PStorageDevice; Request:Integer; Argument1:LongWord; var Argument2:LongWord):LongWord;
Description: To be documented
| Note | None documented |
|---|
Return to Unit Reference
