Difference between revisions of "Unit VersatilePB"

Latest revision as of 05:48, 9 June 2017

0x10000000 System registers
0x10001000 PCI controller config registers
0x10002000 Serial bus interface
0x10003000 Secondary interrupt controller
0x10004000 AACI (audio)
0x10005000 MMCI0
0x10006000 KMI0 (keyboard)
0x10007000 KMI1 (mouse)
0x10008000 Character LCD Interface
0x10009000 UART3
0x1000a000 Smart card 1
0x1000b000 MMCI1
0x10010000 Ethernet
0x10020000 USB
0x10100000 SSMC
0x10110000 MPMC
0x10120000 CLCD Controller
0x10130000 DMA Controller
0x10140000 Vectored interrupt controller
0x101d0000 AHB Monitor Interface
0x101e0000 System Controller
0x101e1000 Watchdog Interface
0x101e2000 Timer 0/1
0x101e3000 Timer 2/3
0x101e4000 GPIO port 0
0x101e5000 GPIO port 1
0x101e6000 GPIO port 2
0x101e7000 GPIO port 3
0x101e8000 RTC
0x101f0000 Smart card 0
0x101f1000 UART0
0x101f2000 UART1
0x101f3000 UART2
0x101f4000 SSPI
0x34000000 NOR Flash

Constants

VersatilePB specific constants VERSATILEPB_*

`VERSATILEPB_CPU_COUNT = 1;`

Physical memory addresses of VersatilePB peripherals (See: \hw\arm\versatilepb.c and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Bbajihec.html) See also: \arch\arm\mach-versatile\include\mach\platform.h

`VERSATILEPB_PERIPHERALS_BASE = $10000000;`
`VERSATILEPB_PERIPHERALS_SIZE = SIZE_2M;`

Peripherals
`VERSATILEPB_SYS_REGS_BASE = $10000000;`	System Registers
`VERSATILEPB_PCI_CORE_REGS_BASE = $10001000;`	PCI core control
`VERSATILEPB_I2C_REGS_BASE = $10002000;`	I2C control
`VERSATILEPB_SIC_REGS_BASE = $10003000;`	Secondary interrupt controller
`VERSATILEPB_AACI_REGS_BASE = $10004000;`	PL041 Audio
`VERSATILEPB_MMCI0_REGS_BASE = $10005000;`	PL180 MMC interface
`VERSATILEPB_KMI0_REGS_BASE = $10006000;`	PL050 KMI interface
`VERSATILEPB_KMI1_REGS_BASE = $10007000;`	PL050 KMI 2nd interface
`VERSATILEPB_CHAR_LCD_REGS_BASE = $10008000;`	Character LCD
`VERSATILEPB_UART3_REGS_BASE = $10009000;`	PL011 UART 3
`VERSATILEPB_SCI1_REGS_BASE = $1000A000;`
`VERSATILEPB_MMCI1_REGS_BASE = $1000B000;`	PL180 MMC Interface
0x1000C000 - 0x1000CFFF = reserved
`VERSATILEPB_ETH_REGS_BASE = $10010000;`	LAN91C111 Ethernet
`VERSATILEPB_USB_REGS_BASE = $10020000;`	OHCI USB
0x10030000 - 0x100FFFFF = reserved
`VERSATILEPB_SMC_REGS_BASE = $10100000;`	SMC
`VERSATILEPB_MPMC_REGS_BASE = $10110000;`	MPMC
`VERSATILEPB_CLCD_REGS_BASE = $10120000;`	PL110 CLCD
`VERSATILEPB_DMAC_REGS_BASE = $10130000;`	PL080 DMA controller
`VERSATILEPB_VIC_REGS_BASE = $10140000;`	PL190 Vectored interrupt controller

`VERSATILEPB_AHBM_REGS_BASE = $101D0000;`	AHB monitor
`VERSATILEPB_SYSCTRL_REGS_BASE = $101E0000;`	System controller
`VERSATILEPB_WATCHDOG_REGS_BASE = $101E1000;`	Watchdog
`VERSATILEPB_TIMER0_REGS_BASE = $101e2000;`	SP804 Timer 0
`VERSATILEPB_TIMER1_REGS_BASE = $101e2020;`	SP804 Timer 1
`VERSATILEPB_TIMER2_REGS_BASE = $101e3000;`	SP804 Timer 2
`VERSATILEPB_TIMER3_REGS_BASE = $101e3020;`	SP804 Timer 3
`VERSATILEPB_GPIO0_REGS_BASE = $101E4000;`	PL061 GPIO port 0
`VERSATILEPB_GPIO1_REGS_BASE = $101E5000;`	PL061 GPIO port 1
`VERSATILEPB_GPIO2_REGS_BASE = $101E6000;`	PL061 GPIO port 2
`VERSATILEPB_GPIO3_REGS_BASE = $101E7000;`	PL061 GPIO port 3
`VERSATILEPB_RTC_REGS_BASE = $101E8000;`	PL031 Real Time Clock
0x101E9000 - reserved
`VERSATILEPB_SCI_REGS_BASE = $101F0000;`	Smart card controller
`VERSATILEPB_UART0_REGS_BASE = $101f1000;`	PL011 UART0
`VERSATILEPB_UART1_REGS_BASE = $101f2000;`	PL011 UART1
`VERSATILEPB_UART2_REGS_BASE = $101f3000;`	PL011 UART2
`VERSATILEPB_SSP_REGS_BASE = $101F4000;`	Synchronous Serial Port

[Expand]

VersatilePB IRQ VERSATILEPB_IRQ_*

IRQ lines of VersatilePB peripherals (See: \hw\arm\versatilepb.c and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Bbajihec.html) Interrupt Assignments (Primary) (See: \arch\arm\mach-versatile\include\mach\platform.h)

`VERSATILEPB_IRQ_WDOG = 0;`	Watchdog timer
`VERSATILEPB_IRQ_SOFT = 1;`	Software interrupt
`VERSATILEPB_IRQ_COMMRX = 2;`	Debug Comm Rx interrupt
`VERSATILEPB_IRQ_COMMTX = 3;`	Debug Comm Tx interrupt
`VERSATILEPB_IRQ_TIMER0_1 = 4;`	Timer 0 and 1
`VERSATILEPB_IRQ_TIMER2_3 = 5;`	Timer 2 and 3
`VERSATILEPB_IRQ_GPIO0 = 6;`	GPIO 0
`VERSATILEPB_IRQ_GPIO1 = 7;`	GPIO 1
`VERSATILEPB_IRQ_GPIO2 = 8;`	GPIO 2
`VERSATILEPB_IRQ_GPIO3 = 9;`	GPIO 3
`VERSATILEPB_IRQ_RTC = 10;`	Real Time Clock
`VERSATILEPB_IRQ_SSP = 11;`	Synchronous Serial Port
`VERSATILEPB_IRQ_UART0 = 12;`	UART 0 on development chip
`VERSATILEPB_IRQ_UART1 = 13;`	UART 1 on development chip
`VERSATILEPB_IRQ_UART2 = 14;`	UART 2 on development chip
`VERSATILEPB_IRQ_SCI = 15;`	Smart Card Interface
`VERSATILEPB_IRQ_CLCD = 16;`	CLCD controller
`VERSATILEPB_IRQ_DMA = 17;`	DMA controller
`VERSATILEPB_IRQ_PWRFAIL = 18;`	Power failure
`VERSATILEPB_IRQ_MBX = 19;`	Graphics processor
`VERSATILEPB_IRQ_GND = 20;`	Reserved
External interrupt signals from logic tiles or secondary controller
`VERSATILEPB_IRQ_VICSOURCE21 = 21;`	Disk on Chip
`VERSATILEPB_IRQ_VICSOURCE22 = 22;`	MCI0A
`VERSATILEPB_IRQ_VICSOURCE23 = 23;`	MCI1A
`VERSATILEPB_IRQ_VICSOURCE24 = 24;`	AACI
`VERSATILEPB_IRQ_VICSOURCE25 = 25;`	Ethernet
`VERSATILEPB_IRQ_VICSOURCE26 = 26;`	USB
`VERSATILEPB_IRQ_VICSOURCE27 = 27;`	PCI 0
`VERSATILEPB_IRQ_VICSOURCE28 = 28;`	PCI 1
`VERSATILEPB_IRQ_VICSOURCE29 = 29;`	PCI 2
`VERSATILEPB_IRQ_VICSOURCE30 = 30;`	PCI 3
`VERSATILEPB_IRQ_VICSOURCE31 = 31;`	SIC source
Passthrough interrupt signals from secondary controller
`VERSATILEPB_IRQ_DOC = VERSATILEPB_IRQ_VICSOURCE21;`
`VERSATILEPB_IRQ_MMCI0A = VERSATILEPB_IRQ_VICSOURCE22;`
`VERSATILEPB_IRQ_MMCI1A = VERSATILEPB_IRQ_VICSOURCE23;`
`VERSATILEPB_IRQ_AACI = VERSATILEPB_IRQ_VICSOURCE24;`
`VERSATILEPB_IRQ_ETH = VERSATILEPB_IRQ_VICSOURCE25;`
`VERSATILEPB_IRQ_USB = VERSATILEPB_IRQ_VICSOURCE26;`
`VERSATILEPB_IRQ_PCI0 = VERSATILEPB_IRQ_VICSOURCE27;`
`VERSATILEPB_IRQ_PCI1 = VERSATILEPB_IRQ_VICSOURCE28;`
`VERSATILEPB_IRQ_PCI2 = VERSATILEPB_IRQ_VICSOURCE29;`
`VERSATILEPB_IRQ_PCI3 = VERSATILEPB_IRQ_VICSOURCE30;`
`VERSATILEPB_IRQ_SICSOURCE = VERSATILEPB_IRQ_VICSOURCE31;`

Interrupt Assignments (Secondary) (See: \arch\arm\mach-versatile\include\mach\platform.h)
`VERSATILEPB_IRQ_SIC_SOFTINT = 32;`	SIC IRQ 0 (Soft Interrupt)
`VERSATILEPB_IRQ_SIC_MMCI0B = 33;`	SIC IRQ 1 (Multimedia Card 0B)
`VERSATILEPB_IRQ_SIC_MMCI1B = 34;`	SIC IRQ 2 (Multimedia Card 1B)
`VERSATILEPB_IRQ_SIC_KMI0 = 35;`	SIC IRQ 3 (Keyboard/Mouse port 0)
`VERSATILEPB_IRQ_SIC_KMI1 = 36;`	SIC IRQ 4 (Keyboard/Mouse port 1)
`VERSATILEPB_IRQ_SIC_SCI3 = 37;`	SIC IRQ 5 (Smart Card interface)
`VERSATILEPB_IRQ_SIC_UART3 = 38;`	SIC IRQ 6 (UART 3 empty or data available)
`VERSATILEPB_IRQ_SIC_CHAR_LCD = 39;`	SIC IRQ 7 (Character LCD)
`VERSATILEPB_IRQ_SIC_TOUCH = 40;`	SIC IRQ 8 (Touchscreen)
`VERSATILEPB_IRQ_SIC_KEYPAD = 41;`	SIC IRQ 9 (Key pressed on display keypad)
42 to 52 (SIC IRQ 10 to 20) - Reserved
`VERSATILEPB_IRQ_SIC_DOC = 53;`	SIC IRQ 21 (Disk on Chip memory controller)
`VERSATILEPB_IRQ_SIC_MMCI0A = 54;`	SIC IRQ 22 (MMC 0A)
`VERSATILEPB_IRQ_SIC_MMCI1A = 55;`	SIC IRQ 23 (MMC 1A)
`VERSATILEPB_IRQ_SIC_AACI = 56;`	SIC IRQ 24 (Audio Codec)
`VERSATILEPB_IRQ_SIC_ETH = 57;`	SIC IRQ 25 (Ethernet controller)
`VERSATILEPB_IRQ_SIC_USB = 58;`	SIC IRQ 26 (USB controller)
`VERSATILEPB_IRQ_SIC_PCI0 = 59;`	SIC IRQ 27
`VERSATILEPB_IRQ_SIC_PCI1 = 60;`	SIC IRQ 28
`VERSATILEPB_IRQ_SIC_PCI2 = 61;`	SIC IRQ 29
`VERSATILEPB_IRQ_SIC_PCI3 = 62;`	SIC IRQ 30

[Expand]

VersatilePB IRQ count VERSATILEPB_*_IRQ_COUNT*

[Expand]

VersatilePB FIQ count VERSATILEPB_FIQ_COUNT*

[Expand]

VersatilePB timer frequency VERSATILEPB_TIMER_FREQUENCY*

[Expand]

VersatilePB system register VERSATILEPB_SYS_*

System register offsets (See: \arch\arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)

`VERSATILEPB_SYS_ID = VERSATILEPB_SYS_REGS_BASE + $00;`
`VERSATILEPB_SYS_SW = VERSATILEPB_SYS_REGS_BASE + $04;`
`VERSATILEPB_SYS_LED = VERSATILEPB_SYS_REGS_BASE + $08;`
`VERSATILEPB_SYS_OSC0 = VERSATILEPB_SYS_REGS_BASE + $0C;`
`VERSATILEPB_SYS_OSC1 = VERSATILEPB_SYS_REGS_BASE + $10;`
`VERSATILEPB_SYS_OSC2 = VERSATILEPB_SYS_REGS_BASE + $14;`
`VERSATILEPB_SYS_OSC3 = VERSATILEPB_SYS_REGS_BASE + $18;`
`VERSATILEPB_SYS_OSC4 = VERSATILEPB_SYS_REGS_BASE + $1C;`
`VERSATILEPB_SYS_OSCCLCD = VERSATILEPB_SYS_REGS_BASE + $1c;`
`VERSATILEPB_SYS_LOCK = VERSATILEPB_SYS_REGS_BASE + $20;`
`VERSATILEPB_SYS_100HZ = VERSATILEPB_SYS_REGS_BASE + $24;`
`VERSATILEPB_SYS_CFGDATA1 = VERSATILEPB_SYS_REGS_BASE + $28;`
`VERSATILEPB_SYS_CFGDATA2 = VERSATILEPB_SYS_REGS_BASE + $2C;`
`VERSATILEPB_SYS_FLAGS = VERSATILEPB_SYS_REGS_BASE + $30;`
`VERSATILEPB_SYS_FLAGSSET = VERSATILEPB_SYS_REGS_BASE + $30;`
`VERSATILEPB_SYS_FLAGSCLR = VERSATILEPB_SYS_REGS_BASE + $34;`
`VERSATILEPB_SYS_NVFLAGS = VERSATILEPB_SYS_REGS_BASE + $38;`
`VERSATILEPB_SYS_NVFLAGSSET = VERSATILEPB_SYS_REGS_BASE + $38;`
`VERSATILEPB_SYS_NVFLAGSCLR = VERSATILEPB_SYS_REGS_BASE + $3C;`
`VERSATILEPB_SYS_RESETCTL = VERSATILEPB_SYS_REGS_BASE + $40;`
`VERSATILEPB_SYS_PCICTL = VERSATILEPB_SYS_REGS_BASE + $44;`
`VERSATILEPB_SYS_MCI = VERSATILEPB_SYS_REGS_BASE + $48;`
`VERSATILEPB_SYS_FLASH = VERSATILEPB_SYS_REGS_BASE + $4C;`
`VERSATILEPB_SYS_CLCD = VERSATILEPB_SYS_REGS_BASE + $50;`
`VERSATILEPB_SYS_CLCDSER = VERSATILEPB_SYS_REGS_BASE + $54;`
`VERSATILEPB_SYS_BOOTCS = VERSATILEPB_SYS_REGS_BASE + $58;`
`VERSATILEPB_SYS_24MHZ = VERSATILEPB_SYS_REGS_BASE + $5C;`
`VERSATILEPB_SYS_MISC = VERSATILEPB_SYS_REGS_BASE + $60;`
`VERSATILEPB_SYS_TEST_OSC0 = VERSATILEPB_SYS_REGS_BASE + $80;`
`VERSATILEPB_SYS_TEST_OSC1 = VERSATILEPB_SYS_REGS_BASE + $84;`
`VERSATILEPB_SYS_TEST_OSC2 = VERSATILEPB_SYS_REGS_BASE + $88;`
`VERSATILEPB_SYS_TEST_OSC3 = VERSATILEPB_SYS_REGS_BASE + $8C;`
`VERSATILEPB_SYS_TEST_OSC4 = VERSATILEPB_SYS_REGS_BASE + $90;`

System register bits (See: \arch\arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)
`VERSATILEPB_SYS_100HZ_FREQUENCY = 100;`

`VERSATILEPB_SYS_LOCK_LOCKED = (1 shl 16);`	This bit indicates if the control registers are locks or unlocked
`VERSATILEPB_SYS_LOCK_LOCKVAL = $A05F;`	Write this value to unlock the control registers, write any other to lock the registers

`VERSATILEPB_SYS_RESETCTL_RESET = (1 shl 8);`
`VERSATILEPB_SYS_RESETCTL_CONFIGCLR = $01;`
`VERSATILEPB_SYS_RESETCTL_CONFIGINIT = $02;`
`VERSATILEPB_SYS_RESETCTL_DLLRESET = $03;`
`VERSATILEPB_SYS_RESETCTL_PLLRESET = $04;`
`VERSATILEPB_SYS_RESETCTL_PORRESET = $05;`
`VERSATILEPB_SYS_RESETCTL_DOCRESET = $06;`

`VERSATILEPB_SYS_MCI_CD0 = (1 shl 0);`	Card detect 0
`VERSATILEPB_SYS_MCI_CD1 = (1 shl 1);`	Card detect 1
`VERSATILEPB_SYS_MCI_WP0 = (1 shl 2);`	Write protect 0
`VERSATILEPB_SYS_MCI_WP1 = (1 shl 3);`	Write protect 1

`VERSATILEPB_SYS_CLCD_MODE888 = 0;`	LCD Mode [1:0], controls mapping of video memory to RGB signals 00 = 8:8:8
`VERSATILEPB_SYS_CLCD_MODE5551 = 1;`	01 = 5:5:5:1
`VERSATILEPB_SYS_CLCD_MODE565BGR = 2;`	10 = 5:6:5, red LSB
`VERSATILEPB_SYS_CLCD_MODE565RGB = 3;`	11 = 5:6:5, blue LSB

`VERSATILEPB_SYS_CLCD_MODEMASK = 3;`

`VERSATILEPB_SYS_24MHZ_FREQUENCY = 24000000;`

[Expand]

VersatilePB system control VERSATILEPB_SYSCTRL_*

[Expand]

SP804 timer SP804_TIMER_*

[Expand]

SP804 timer control SP804_TIMER_CONTROL_*

[Expand]

PL190 vectored interrupt controller offsets PL190_VIC_*

[Expand]

PL190 vectored interrupt controller register PL190_VIC_VECTCNTL_*

[Expand]

VersatilePB secondary interrupt controller VERSATILEPB_SIC_*

Type definitions

SP804 timer registers

[Expand]

PSP804TimerRegisters = ^TSP804TimerRegisters;

TSP804TimerRegisters = record

PL190 interrupt controller

[Expand]

PPL190InterruptRegisters = ^TPL190InterruptRegisters;

TPL190InterruptRegisters = record

PL190 vector address

[Expand]

PPL190VectorAddressRegisters = ^TPL190VectorAddressRegisters;

TPL190VectorAddressRegisters = record

PL190 vector control

[Expand]

PPL190VectorControlRegisters = ^TPL190VectorControlRegisters;

TPL190VectorControlRegisters = record

VersatilePB secondary interrupt controller

[Expand]

PVersatilePBInterruptRegisters = ^TVersatilePBInterruptRegisters;

TVersatilePBInterruptRegisters = record

Public variables

None defined

Function declarations

None defined

Return to Unit Reference

Number of IRQs on the Vectored (Primary) Interrupt Controller (VIC)
`VERSATILEPB_VIC_IRQ_COUNT = 32;`

Number of IRQs on the Secondary Interrupt Controller (SIC)
`VERSATILEPB_SIC_IRQ_COUNT = 32;`

Total number of IRQs available
`VERSATILEPB_IRQ_COUNT = VERSATILEPB_VIC_IRQ_COUNT + VERSATILEPB_SIC_IRQ_COUNT;`	64

System Control register bits (See: http://infocenter.arm.com/help/topic/com.arm.doc.dui0440b/CACIHEAD.html)

`VERSATILEPB_SYSCTRL_REFCLK = 0;`	REFCLK is 32.768kHz
`VERSATILEPB_SYSCTRL_TIMCLK = 1;`	TIMCLK is 1MHz

`VERSATILEPB_SYSCTRL_TIMER0_ENSEL = 15;`	Timer 0 enable/Timer Reference Select. If 0, the timing reference is REFCLK. If 1, the timing reference is TIMCLK.
`VERSATILEPB_SYSCTRL_TIMER1_ENSEL = 17;`	Timer 1 enable/Timer Reference Select. If 0, the timing reference is REFCLK. If 1, the timing reference is TIMCLK.
`VERSATILEPB_SYSCTRL_TIMER2_ENSEL = 19;`	Timer 2 enable/Timer Reference Select. If 0, the timing reference is REFCLK. If 1, the timing reference is TIMCLK.
`VERSATILEPB_SYSCTRL_TIMER3_ENSEL = 21;`	Timer 3 enable/Timer Reference Select. If 0, the timing reference is REFCLK. If 1, the timing reference is TIMCLK.

SP804 Timer register offsets (See: http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/DDI0271.pdf)

`SP804_TIMER_LOAD = $00;`	Timer Load register
`SP804_TIMER_VALUE = $04;`	Timer Value register
`SP804_TIMER_CONTROL = $08;`	Timer control register
`SP804_TIMER_INT_CLEAR = $0c;`	Timer Interrupt clear register
`SP804_TIMER_RAW_INT = $10;`	Timer Raw Interrupt register
`SP804_TIMER_MASKED_INT = $14;`	Timer Masked Interrupt register
`SP804_TIMER_BACKGROUND_LOAD = $18;`	Timer Background Load register

SP804 Timer register bits (See: http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/DDI0271.pdf)

`SP804_TIMER_CONTROL_ONESHOT = (1 shl 0);`	Selects one-shot or wrapping counter mode: (0 = wrapping mode (default)/1 = one-shot mode)
`SP804_TIMER_CONTROL_32BIT = (1 shl 1);`	Selects 16/32 bit counter operation: (0 = 16-bit counter (default)/1 = 32-bit counter)
`SP804_TIMER_CONTROL_PRESCALE1 = (0 shl 2);`	Prescale bits: 00 = 0 stages of prescale, clock is divided by 1 (default)
`SP804_TIMER_CONTROL_PRESCALE16 = (1 shl 2);`	01 = 4 stages of prescale, clock is divided by 16
`SP804_TIMER_CONTROL_PRESCALE256 = (2 shl 2);`	10 = 8 stages of prescale, clock is divided by 256
`SP804_TIMER_CONTROL_INT_ENABLED = (1 shl 5);`	Interrupt Enable bit: (0 = Timer module Interrupt disabled/1 = Timer module Interrupt enabled (default))
`SP804_TIMER_CONTROL_PERIODIC = (1 shl 6);`	Mode bit: (0 = Timer module is in free-running mode (default)/1 = Timer module is in periodic mode)
`SP804_TIMER_CONTROL_TIMER_ENABLED = (1 shl 7);`	Enable bit: (0 = Timer module disabled (default)/1 = Timer module enabled)

PL190 Vectored Interrupt Controller register offsets (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0181e/index.html)

`PL190_VIC_IRQSTATUS = $00;`	IRQ Status Register
`PL190_VIC_FIQSTATUS = $04;`	FIQ Status Register
`PL190_VIC_RAWINTR = $08;`	Raw Interrupt Status Register
`PL190_VIC_INTSELECT = $0c;`	Interrupt Select Register (1 = FIQ, 0 = IRQ)
`PL190_VIC_INTENABLE = $10;`	Interrupt Enable Register
`PL190_VIC_INTENCLEAR = $14;`	Interrupt Enable Clear Register
`PL190_VIC_SOFTINT = $18;`	Software Interrupt Register
`PL190_VIC_SOFTINTCLEAR = $1c;`	Software Interrupt Clear Register
`PL190_VIC_PROTECTION = $20;`	Protection Enable Register
`PL190_VIC_VECTADDR = $30;`	Vector Address Register (PL190 only)
`PL190_VIC_DEFVECTADDR = $34;`	Default Vector Address Register (PL190 only)
`PL190_VIC_VECTADDR0 = $100;`	Vector Address Registers (0 to 15) (0..31 PL192)
`PL190_VIC_VECTCNTL0 = $200;`	Vector Control Registers (0 to 15) (0..31 PL192)

Difference between revisions of "Unit VersatilePB"

Latest revision as of 05:48, 9 June 2017

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

@@ Line 4: / Line 4: @@
 === Description ===
 ----
+'''Ultibo Definitions specific to the ARM Versatile Platform Baseboard unit'''
 From the QEMU source the memory map of the VersatilePB is shown as this:
@@ Line 66: / Line 68: @@
 | &nbsp;
 |-
-| <code>VERSATILEPB_PERIPHERALS_SIZE = $001FFFFF;</code>
+| <code>VERSATILEPB_PERIPHERALS_SIZE = SIZE_2M;</code>
 | &nbsp;
 |-
@@ Line 132: / Line 134: @@
 |-
 | <code>VERSATILEPB_VIC_REGS_BASE = $10140000;</code>
-| PL190Vectored interrupt controller
+| PL190 Vectored interrupt controller
 |-
 |colspan="2"|&nbsp;
@@ Line 337: / Line 339: @@
 |colspan="2"|&nbsp;
 |-
-|colspan="2"|Interrupt Assignments (Secondary)(See: \arch\arm\mach-versatile\include\mach\platform.h)
+|colspan="2"|Interrupt Assignments (Secondary) (See: \arch\arm\mach-versatile\include\mach\platform.h)
 |-
 | <code>VERSATILEPB_IRQ_SIC_SOFTINT = 32;</code>
@@ Line 412: / Line 414: @@
 |-
 | <code>VERSATILEPB_VIC_IRQ_COUNT = 32;</code>
-| &nbsp;
+| style="width: 50%;"|&nbsp;
 |-
 |colspan="2"|&nbsp;
@@ Line 462: / Line 464: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-|colspan="2"|System register offsets (See: \arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)
+|colspan="2"|System register offsets (See: \arch\arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)
 |-
 |colspan="2"|&nbsp;
@@ Line 567: / Line 569: @@
 |colspan="2"|&nbsp;
 |-
-|colspan="2"|System register bits (See: \arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)
+|colspan="2"|System register bits (See: \arch\arm\mach-versatile\include\mach\platform.h and http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/I1006122.html)
+|-
+| <code>VERSATILEPB_SYS_100HZ_FREQUENCY = 100;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>VERSATILEPB_SYS_LOCK_LOCKED = (1 shl 16);</code>
+| This bit indicates if the control registers are locks or unlocked
+|-
+| <code>VERSATILEPB_SYS_LOCK_LOCKVAL = $A05F;</code>
+| Write this value to unlock the control registers, write any other to lock the registers
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_RESET = (1 shl 8);</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_CONFIGCLR = $01;</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_CONFIGINIT = $02;</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_DLLRESET = $03;</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_PLLRESET = $04;</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_PORRESET = $05;</code>
+| &nbsp;
+|-
+| <code>VERSATILEPB_SYS_RESETCTL_DOCRESET = $06;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>VERSATILEPB_SYS_MCI_CD0 = (1 shl 0);</code>
+| Card detect 0
+|-
+| <code>VERSATILEPB_SYS_MCI_CD1 = (1 shl 1);</code>
+| Card detect 1
+|-
+| <code>VERSATILEPB_SYS_MCI_WP0 = (1 shl 2);</code>
+| Write protect 0
+|-
+| <code>VERSATILEPB_SYS_MCI_WP1 = (1 shl 3);</code>
+| Write protect 1
+|-
+|colspan="2"|&nbsp;
 |-
 | <code>VERSATILEPB_SYS_CLCD_MODE888 = 0;</code>
@@ Line 584: / Line 636: @@
 |-
 | <code>VERSATILEPB_SYS_CLCD_MODEMASK = 3;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>VERSATILEPB_SYS_24MHZ_FREQUENCY = 24000000;</code>
 | &nbsp;
 |-
@@ Line 813: / Line 870: @@
 ----
-''To be documented''
+'''SP804 timer registers'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PSP804TimerRegisters = ^TSP804TimerRegisters;</code>
+<code>TSP804TimerRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|Layout of the SP804 Timer registers (VersatilePB specific structures) (See: http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/DDI0271.pdf)
+|-
+| <code>Load:LongWord;</code>
+| Timer Load register
+|-
+| <code>Value:LongWord;</code>
+| Timer Value register
+|-
+| <code>Control:LongWord;</code>
+| Timer control register
+|-
+| <code>IRQClear:LongWord;</code>
+| Timer IRQ clear register
+|-
+| <code>RawIRQ:LongWord;</code>
+| Timer Raw IRQ register
+|-
+| <code>MaskedIRQ:LongWord;</code>
+| Timer Masked IRQ register
+|-
+| <code>BackgroundLoad:LongWord;</code>
+| Timer Background Load register
+|-
+|}
+</div></div>
+'''PL190 interrupt controller'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PPL190InterruptRegisters = ^TPL190InterruptRegisters;</code>
+<code>TPL190InterruptRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|Layout of the PL190 Vectored Interrupt Controller registers (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0181e/index.html)
+|-
+| <code>IRQSTATUS:LongWord;</code>
+| IRQ Status Register
+|-
+| <code>FIQSTATUS:LongWord;</code>
+| FIQ Status Register
+|-
+| <code>RAWINTR:LongWord;</code>
+| Raw Interrupt Status Register
+|-
+| <code>INTSELECT:LongWord;</code>
+| Interrupt Select Register
+|-
+| <code>INTENABLE:LongWord;</code>
+| Interrupt Enable Register
+|-
+| <code>INTENCLEAR:LongWord;</code>
+| Interrupt Enable Clear Register
+|-
+| <code>SOFTINT:LongWord;</code>
+| Software Interrupt Register
+|-
+| <code>SOFTINTCLEAR:LongWord;</code>
+| Software Interrupt Clear Register
+|-
+| <code>PROTECTION:LongWord;</code>
+| Protection Enable Register
+|-
+| <code>RESERVED1:LongWord;</code>
+| &nbsp;
+|-
+| <code>RESERVED2:LongWord;</code>
+| &nbsp;
+|-
+| <code>RESERVED3:LongWord;</code>
+| &nbsp;
+|-
+| <code>VECTADDR:LongWord;</code>
+| Vector Address Register
+|-
+| <code>DEFVECTADDR:LongWord;</code>
+| Default Vector Address Register
+|-
+|}
+</div></div>
+'''PL190 vector address'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PPL190VectorAddressRegisters = ^TPL190VectorAddressRegisters;</code>
+<code>TPL190VectorAddressRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>VECTADDR:array[0..15] of LongWord;</code>
+| Vector Address Register
+|-
+|}
+</div></div>
+'''PL190 vector control'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PPL190VectorControlRegisters = ^TPL190VectorControlRegisters;</code>
+<code>TPL190VectorControlRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>VECTCNTL:array[0..15] of LongWord;</code>
+| Vector Control Registers
+|-
+|}
+</div></div>
+'''VersatilePB secondary interrupt controller'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PVersatilePBInterruptRegisters = ^TVersatilePBInterruptRegisters;</code>
+<code>TVersatilePBInterruptRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|Layout of the VersatilePB Secondary Interrupt Controller registers (See: http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Cacdggia.html)
+|-
+| <code>SIC_STATUS:LongWord;</code>
+| Status of interrupt (after mask) (Read)
+|-
+| <code>SIC_RAWSTAT:LongWord;</code>
+| Status of interrupt (before mask) (Read)
+|-
+| <code>SIC_ENSET:LongWord;</code>
+| Interrupt mask / Set bits HIGH to enable the corresponding interrupt signals (Read/Write)
+|-
+| <code>SIC_ENCLR:LongWord;</code>
+| Set bits HIGH to mask the corresponding interrupt signals (Write)
+|-
+| <code>SIC_SOFTINTSET:LongWord;</code>
+| Set software interrupt (Read/Write)
+|-
+| <code>SIC_SOFTINTCLR:LongWord;</code>
+| Clear software interrupt (Write)
+|-
+| <code>RESERVED1:LongWord;</code>
+| &nbsp;
+|-
+| <code>RESERVED2:LongWord;</code>
+| &nbsp;
+|-
+| <code>SIC_PICENSET:LongWord;</code>
+| Pass-through mask (allows interrupt to pass directly to the primary interrupt controller) / Set bits HIGH to set the corresponding interrupt pass-through mask bits (Read/Write)
+|-
+| <code>SIC_PICENCLR:LongWord;</code>
+| Set bits HIGH to clear the corresponding interrupt pass-through mask bits (Write)
+|-
+|}
+</div></div>
+<br />
 === Public variables ===
 ----
-''To be documented''
+''None defined''
 === Function declarations ===
 ----
-''To be documented''
+''None defined''
 Return to [[Unit_Reference|Unit Reference]]

Timer frequencies
`VERSATILEPB_TIMER_FREQUENCY = 1000000;`	Default frequency of the VersatilePB Timer when reference is set to TIMCLK (1MHz)

PL190 Vectored Interrupt Controller register bits (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0181e/index.html)

`PL190_VIC_VECTCNTL_ENABLE = (1 shl 5);`	Enables vector interrupt (This bit is cleared on reset)
`PL190_VIC_VECTCNTL_INTSOURCE = ($1F shl 0);`	Selects interrupt source 0 to 31

VersatilePB Secondary Interrupt Controller register offsets (See: http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Cacdggia.html)

`VERSATILEPB_SIC_STATUS = $00;`	Status of interrupt (after mask) (Read)
`VERSATILEPB_SIC_RAWSTAT = $04;`	Status of interrupt (before mask) (Read)
`VERSATILEPB_SIC_ENABLE = $08;`	Interrupt mask / Set bits HIGH to enable the corresponding interrupt signals (Read/Write)
`VERSATILEPB_SIC_ENSET = $08;`
`VERSATILEPB_SIC_ENCLR = $0C;`	Set bits HIGH to mask the corresponding interrupt signals (Write)
`VERSATILEPB_SIC_SOFTINTSET = $10;`	Set software interrupt (Read/Write)
`VERSATILEPB_SIC_SOFTINTCLR = $14;`	Clear software interrupt (Write)
`VERSATILEPB_SIC_PICENABLE = $20;`	Pass-through mask (allows interrupt to pass directly to the primary interrupt controller)/Set bits HIGH to set the corresponding interrupt pass-through mask bits (Read/Write)
`VERSATILEPB_SIC_PICENSET = $20;`
`VERSATILEPB_SIC_PICENCLR = $24;`	Set bits HIGH to clear the corresponding interrupt pass-through mask bits (Write)

VersatilePB Secondary Interrupt Controller register bits (See: http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Cacdggia.html)
`VERSATILEPB_SIC_PIC_MASK = $7FE00000;`	Interrupts on secondary controller from 21 to 30 are routed directly to the VIC on the corresponding number on primary controller

Layout of the SP804 Timer registers (VersatilePB specific structures) (See: http://infocenter.arm.com/help/topic/com.arm.doc.ddi0271d/DDI0271.pdf)
`Load:LongWord;`	Timer Load register
`Value:LongWord;`	Timer Value register
`Control:LongWord;`	Timer control register
`IRQClear:LongWord;`	Timer IRQ clear register
`RawIRQ:LongWord;`	Timer Raw IRQ register
`MaskedIRQ:LongWord;`	Timer Masked IRQ register
`BackgroundLoad:LongWord;`	Timer Background Load register

Layout of the PL190 Vectored Interrupt Controller registers (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0181e/index.html)
`IRQSTATUS:LongWord;`	IRQ Status Register
`FIQSTATUS:LongWord;`	FIQ Status Register
`RAWINTR:LongWord;`	Raw Interrupt Status Register
`INTSELECT:LongWord;`	Interrupt Select Register
`INTENABLE:LongWord;`	Interrupt Enable Register
`INTENCLEAR:LongWord;`	Interrupt Enable Clear Register
`SOFTINT:LongWord;`	Software Interrupt Register
`SOFTINTCLEAR:LongWord;`	Software Interrupt Clear Register
`PROTECTION:LongWord;`	Protection Enable Register
`RESERVED1:LongWord;`
`RESERVED2:LongWord;`
`RESERVED3:LongWord;`
`VECTADDR:LongWord;`	Vector Address Register
`DEFVECTADDR:LongWord;`	Default Vector Address Register

Layout of the VersatilePB Secondary Interrupt Controller registers (See: http://infocenter.arm.com/help/topic/com.arm.doc.dui0224i/Cacdggia.html)
`SIC_STATUS:LongWord;`	Status of interrupt (after mask) (Read)
`SIC_RAWSTAT:LongWord;`	Status of interrupt (before mask) (Read)
`SIC_ENSET:LongWord;`	Interrupt mask / Set bits HIGH to enable the corresponding interrupt signals (Read/Write)
`SIC_ENCLR:LongWord;`	Set bits HIGH to mask the corresponding interrupt signals (Write)
`SIC_SOFTINTSET:LongWord;`	Set software interrupt (Read/Write)
`SIC_SOFTINTCLR:LongWord;`	Clear software interrupt (Write)
`RESERVED1:LongWord;`
`RESERVED2:LongWord;`
`SIC_PICENSET:LongWord;`	Pass-through mask (allows interrupt to pass directly to the primary interrupt controller) / Set bits HIGH to set the corresponding interrupt pass-through mask bits (Read/Write)
`SIC_PICENCLR:LongWord;`	Set bits HIGH to clear the corresponding interrupt pass-through mask bits (Write)