Difference between revisions of "Unit PlatformQEMUVPB"

Latest revision as of 05:40, 7 April 2023

`QEMUVPB_VECTOR_TABLE_BASE = $00001000;`	Place the Interrupt Vector Table at 0x00001000 before the code start at 0x00010000
`QEMUVPB_VECTOR_TABLE_SIZE = SIZE_64;`	The Interrupt Vector Table is exactly 64 bytes (16 32 bit (4 byte) entries)
`QEMUVPB_VECTOR_TABLE_COUNT = 8;`	The Interrupt Vector Table contains 8 entries on an ARMv7 device

QEMUVPB CPU count QEMUVPB_CPU_*

`QEMUVPB_CPU_COUNT = VERSATILEPB_CPU_COUNT;`
`QEMUVPB_CPU_BOOT = CPU_ID_0;`
`QEMUVPB_CPU_MASK = CPU_AFFINITY_0;`

QEMUVPB SWI QEMUVPB_SWI_*

`QEMUVPB_SWI_COUNT = 256;`	Number of available SWI entries

QEMUVPB kernel name QEMUVPB_KERNEL_*

`QEMUVPB_KERNEL_NAME = 'kernel.bin';`
`QEMUVPB_KERNEL_NAME = 'kernel64.bin';`
`QEMUVPB_KERNEL_CONFIG = ;`	Not available as a file
`QEMUVPB_KERNEL_COMMAND = ;`	Not available as a file
`QEMUVPB_FIRMWARE_FILES = ;`	Not available as a file
`QEMUVPB_DTB_FILES = ;`	Not available as a file

PL110 specific constants PL110_*

`PL110_FRAMEBUFFER_DESCRIPTION = 'ARM PrimeCell PL110 Color LCD';`	Description of PL110 device

PL110 mode PL110_MODE_*

`PL110_MODE_UNKNOWN = 0;`
`PL110_MODE_VGA = 1;`	Connected to a VGA display
`PL110_MODE_SVGA = 2;`	Connected to a SVGA display
`PL110_MODE_TFT = 3;`	Connected to a TFT display
`PL110_MODE_STN = 4;`	Connected to an STN display

PL110 register offset PL110_CLCD_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_TIMING0 = $00000000;`	Horizontal Axis Panel Control Register
`PL110_CLCD_TIMING1 = $00000004;`	Vertical Axis Panel Control Register
`PL110_CLCD_TIMING2 = $00000008;`	Clock and Signal Polarity Control Register
`PL110_CLCD_TIMING3 = $0000000c;`	Line End Control Register
`PL110_CLCD_UPBASE = $00000010;`	Upper Panel Frame Base Address Registers
`PL110_CLCD_LPBASE = $00000014;`	Lower Panel Frame Base Address Registers
`PL110_CLCD_CONTROL = $00000018;`	Control Register Note: Reversed in VersatilePB implementation, 0x0000001c in PL110 TRM
`PL110_CLCD_IMSC = $0000001c;`	Interrupt Mask Set/Clear Register Note: Reversed in VersatilePB implementation, 0x00000018 in PL110 TRM
`PL110_CLCD_RIS = $00000020;`	Raw Interrupt Status Register
`PL110_CLCD_MIS = $00000024;`	Masked Interrupt Status Register
`PL110_CLCD_ICR = $00000028;`	Interrupt Clear Register
`PL110_CLCD_UPCURR = $0000002C;`	Upper Panel Current Address Value Registers
`PL110_CLCD_LPCURR = $00000030;`	Lower Panel Current Address Value Registers
`PL110_CLCD_PALETTE = $00000200;`	Color Palette Register

PL110 CLCD timing0 PL110_CLCD_TIMING0_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_TIMING0_HBP = ($FF shl 24);`	Horizontal back porch
`PL110_CLCD_TIMING0_HFP = ($FF shl 16);`	Horizontal front porch
`PL110_CLCD_TIMING0_HSW = ($FF shl 8);`	Horizontal synchronization pulse width
`PL110_CLCD_TIMING0_PPL = ($FC shl 2);`	Pixels-per-line (Actual pixels-per-line = 16 * (PPL + 1))

PL110 CLCD timing1 PL110_CLCD_TIMING1_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_TIMING1_VBP = ($FF shl 24);`	Vertical back porch
`PL110_CLCD_TIMING1_VFP = ($FF shl 16);`	Vertical front porch
`PL110_CLCD_TIMING1_VSW = ($FC shl 10);`	Vertical synchronization pulse width
`PL110_CLCD_TIMING1_LPP = ($3FF shl 0);`	Lines per panel is the number of active lines per screen (Program to number of lines required minus 1)

PL110 CLCD timing2 PL110_CLCD_TIMING2_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_TIMING2_PCD_HI = ($1F shl 27);`	Upper five bits of Panel Clock Divisor
`PL110_CLCD_TIMING2_BCD = (1 shl 26);`	Bypass pixel clock divider
`PL110_CLCD_TIMING2_CPL = ($3FF shl 16);`	Clocks per line
`PL110_CLCD_TIMING2_IOE = (1 shl 14);`	Invert output enable
`PL110_CLCD_TIMING2_IPC = (1 shl 13);`	Invert panel clock
`PL110_CLCD_TIMING2_IHS = (1 shl 12);`	Invert horizontal synchron
`PL110_CLCD_TIMING2_IVS = (1 shl 11);`	Invert vertical synchronization
`PL110_CLCD_TIMING2_ACB = ($1F shl 6);`	AC bias pin frequency
`PL110_CLCD_TIMING2_CLKSEL = (1 shl 5);`	This bit drives the CLCDCLKSEL signal which is used as the select signal for the external LCD clock multiplexor
`PL110_CLCD_TIMING2_PCD_LO = ($1F shl 0);`	Lower five bits of Panel Clock Divisor

PL110 CLCD timing3 PL110_CLCD_TIMING3_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_TIMING3_LEE = (1 shl 16);`	LCD Line end enable: 0 = CLLE disabled (held LOW)/1 = CLLE signal active
`PL110_CLCD_TIMING3_LED = ($3F shl 0);`	Line-end signal delay from the rising-edge of the last panel clock

PL110 CLCD control PL110_CLCD_CONTROL_*

See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html

`PL110_CLCD_CONTROL_LCDEN = (1 shl 0);`
`PL110_CLCD_CONTROL_LCDBPP1 = (0 shl 1);`	LCD bits per pixel: 000 = 1 bpp
`PL110_CLCD_CONTROL_LCDBPP2 = (1 shl 1);`	LCD bits per pixel: 001 = 2 bpp
`PL110_CLCD_CONTROL_LCDBPP4 = (2 shl 1);`	LCD bits per pixel: 010 = 4 bpp
`PL110_CLCD_CONTROL_LCDBPP8 = (3 shl 1);`	LCD bits per pixel: 011 = 8 bpp
`PL110_CLCD_CONTROL_LCDBPP16 = (4 shl 1);`	LCD bits per pixel: 100 = 16 bpp
`PL110_CLCD_CONTROL_LCDBPP16_565 = (6 shl 1);`	LCD bits per pixel: 110 = 16 bpp 565 (PL111 only)
`PL110_CLCD_CONTROL_LCDBPP16_444 = (7 shl 1);`	LCD bits per pixel: 111 = 16 bpp 444 (PL111 only)
`PL110_CLCD_CONTROL_LCDBPP24 = (5 shl 1);`	LCD bits per pixel: 101 = 24 bpp
`PL110_CLCD_CONTROL_LCDBW = (1 shl 4);`	STN LCD is monochrome (black and white) (0 = STN LCD is color/1 = STN LCD is monochrome)
`PL110_CLCD_CONTROL_LCDTFT = (1 shl 5);`	LCD is TFT (0 = LCD is an STN display, use gray scaler/1 = LCD is TFT, do not use gray scaler)
`PL110_CLCD_CONTROL_LCDMONO8 = (1 shl 6);`	Monochrome LCD has an 8-bit interface (0 = mono LCD uses 4-bit interface/1 = mono LCD uses 8-bit interface)
`PL110_CLCD_CONTROL_LCDDUAL = (1 shl 7);`	LCD interface is dual panel STN (0 = single panel LCD is in use/1 = dual panel LCD is in use)
`PL110_CLCD_CONTROL_BGR = (1 shl 8);`	RGB or BGR format selection (0 = RGB normal output/1 = BGR red and blue swapped.)
`PL110_CLCD_CONTROL_BEBO = (1 shl 9);`	Big-endian byte order (0 = little-endian byte order/1 = big-endian byte order)
`PL110_CLCD_CONTROL_BEPO = (1 shl 10);`	Big-endian pixel ordering within a byte (0 = little-endian pixel ordering within a byte/1= big-endian pixel ordering within a byte)
`PL110_CLCD_CONTROL_LCDPWR = (1 shl 11);`	LCD power enable
`PL110_CLCD_CONTROL_LCDVCOMP_VSYNC = (0 shl 12);`	Generate interrupt at: 00 = start of vertical synchronization
`PL110_CLCD_CONTROL_LCDVCOMP_BPORCH = (1 shl 12);`	Generate interrupt at: 01 = start of back porch
`PL110_CLCD_CONTROL_LCDVCOMP_VIDEO = (2 shl 12);`	Generate interrupt at: 10 = start of active video
`PL110_CLCD_CONTROL_LCDVCOMP_FPORCH = (3 shl 12);`	Generate interrupt at: 11 = start of front porch
`PL110_CLCD_CONTROL_LDMAFIFOTIME = (1 shl 15);`	Unknown
`PL110_CLCD_CONTROL_WATERMARK = (1 shl 16);`	LCD DMA FIFO Watermark level

PL110 control PL110_CONTROL_*

`PL110_CONTROL_VGA = PL110_CLCD_CONTROL_LCDTFT or PL110_CLCD_CONTROL_LCDVCOMP_BPORCH;`
`PL110_CONTROL_SVGA = PL110_CLCD_CONTROL_LCDTFT or PL110_CLCD_CONTROL_LCDVCOMP_BPORCH;`

PL110 timing0 PL110_TIMING0_*

`PL110_TIMING0_VGA = $3F1F3F9C;`
`PL110_TIMING0_SVGA = $1313A4C4;`

PL110 timing1 PL110_TIMING1_*

`PL110_TIMING1_VGA = $090B61DF;`
`PL110_TIMING1_SVGA = $0505F657;`

PL110 timing2 PL110_TIMING2_*

`PL110_TIMING2_VGA = $067F1800;`
`PL110_TIMING2_SVGA = $071F1800;`

Type definitions

PL110 CLCD registers

PPL110CLCDRegisters = ^TPL110CLCDRegisters;

TPL110CLCDRegisters = record

Note: Layout of the PL110 registers (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html)
`TIMING0:LongWord;`	Horizontal Axis Panel Control Register
`TIMING1:LongWord;`	Vertical Axis Panel Control Register
`TIMING2:LongWord;`	Clock and Signal Polarity Control Register
`TIMING3:LongWord;`	Line End Control Register
`UPBASE:LongWord;`	Upper Panel Frame Base Address Registers
`LPBASE:LongWord;`	Lower Panel Frame Base Address Registers
`CONTROL:LongWord;`	Control Register Note: Reversed in VersatilePB implementation, 0x0000001c in PL110 TRM
`IMSC:LongWord;`	Interrupt Mask Set/Clear Register Note: Reversed in VersatilePB implementation, 0x00000018 in PL110 TRM
`RIS:LongWord;`	Raw Interrupt Status Register
`MIS:LongWord;`	Masked Interrupt Status Register
`ICR:LongWord;`	Interrupt Clear Register
`UPCURR:LongWord;`	Upper Panel Current Address Value Registers
`LPCURR:LongWord;`	Lower Panel Current Address Value Registers

PL110 framebuffer

PPL110Framebuffer = ^TPL110Framebuffer;

TPL110Framebuffer = record

Framebuffer Properties
`Framebuffer:TFramebufferDevice;`
PL110 Properties
`Mode:LongWord;`	PL110 framebuffer mode (eg PL110_MODE_TFT)
`Depth:LongWord;`	Framebuffer color depth (eg FRAMEBUFFER_DEPTH_16)
`Width:LongWord;`	Framebuffer width in pixels
`Height:LongWord;`	Framebuffer height in pixels
`Rotation:LongWord;`	Framebuffer rotation (eg FRAMEBUFFER_ROTATION_180)
Driver Properties
`Control:LongWord;`	Preset Control register value
`Timing0:LongWord;`	Preset Timing0 register value
`Timing1:LongWord;`	Preset Timing1 register value
`Timing2:LongWord;`	Preset Timing2 register value
`Timing3:LongWord;`	Preset Timing2 register value
`Registers:PPL110CLCDRegisters;`	PL110 registers

Public variables

QEMUVPB specific Ultibo variables

`QEMUVPBInitialized:Boolean;`

Clock variables

`ClockGetLast:LongWord;`	Value of 24MHz Counter on last ClockGetCount or ClockGetTotal call

`ClockGetBase:Int64;`	Base value for 64-bit clock, incremented each time the 24MHz Counter rolls over (Only accurate if ClockGetCount/ClockGetTotal is called at least once per 178 seconds)

`ClockGetLock:THandle = INVALID_HANDLE_VALUE;`	Lock handle for creating 64-bit clock from a 32-bit register

`ClockGetTimer:THandle = INVALID_HANDLE_VALUE;`	Timer handle for ensuring clock is read periodically to maintain accurracy

Timer variables

`Timer0Registers:PSP804TimerRegisters;`	Use Timer0 for Clock

`Timer2Registers:PSP804TimerRegisters;`	Use Timer2 for Scheduler

Interrupt variables

`PrimaryInterruptRegisters:PPL190InterruptRegisters;`

`SecondaryInterruptRegisters:PVersatilePBInterruptRegisters;`

`InterruptEntries:array[0..(VERSATILEPB_IRQ_COUNT - 1)] of PInterruptEntry;`

System call

`SystemCallEntries:array[0..QEMUVPB_SWI_COUNT - 1] of TSystemCallEntry;`

IRQ/FIQ

`IRQEnabled:array[0..1] of LongWord;`	2 groups of IRQs to Enable/Disable (See: TPL190InterruptRegisters)

`FIQEnabled:array[0..1] of LongWord;`	2 groups of FIQs to Enable/Disable (See: TPL190InterruptRegisters)

Function declarations

Initialization functions

procedure QEMUVPBInit;

Description: To be documented

Note	None documented

QEMUVPB platform functions

procedure QEMUVPBBoardInit;

Description: To be documented

Note	None documented

procedure QEMUVPBMemoryInit;

Description: To be documented

Note	None documented

procedure QEMUVPBClockInit;

Description: To be documented

Note	None documented

procedure QEMUVPBPowerInit;

Description: To be documented

Note	None documented

procedure QEMUVPBInterruptInit;

Description: To be documented

Note	None documented

procedure QEMUVPBPeripheralInit;

Description: To be documented

Note	None documented

procedure QEMUVPBFramebufferInit;

Description: To be documented

Note	None documented

procedure QEMUVPBPageTableInit;

Description: Initialize the Hardware Page Tables before enabling the MMU

Note	None documented

function QEMUVPBRequestExIRQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;

Description: Request registration of the supplied handler to the specified IRQ number

Note	None documented

function QEMUVPBReleaseExIRQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;

Description: Request deregistration of the supplied handler from the specified IRQ number

Note	None documented

function QEMUVPBRequestExFIQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;

Description: Request registration of the supplied handler to the specified FIQ number

Note	None documented

function QEMUVPBReleaseExFIQ(CPUID,Number:LongWord; Handler:TInterruptHandler; HandlerEx:TInterruptExHandler; Parameter:Pointer):LongWord;

Description: Request deregistration of the supplied handler from the specified FIQ number

Note	None documented

function QEMUVPBRegisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;

Description: Request registration of the supplied handler to the specified interrupt number (Where Applicable)

Note	None documented

function QEMUVPBDeregisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;

Description: Request deregistration of the supplied handler from the specified interrupt number (Where Applicable)

Note	None documented

function QEMUVPBRegisterSystemCallEx(CPUID,Number:LongWord; Handler:TSystemCallHandler; HandlerEx:TSystemCallExHandler):LongWord;

Description: Request registration of the supplied extended handler to the specified System Call number

Note	None documented

function QEMUVPBDeregisterSystemCallEx(CPUID,Number:LongWord; Handler:TSystemCallHandler; HandlerEx:TSystemCallExHandler):LongWord;

Description: Request deregistration of the supplied extended handler from the specified System Call number

Note	None documented

function QEMUVPBGetInterruptEntry(Number,Instance:LongWord; var Interrupt:TInterruptEntry):LongWord;

Description: Get the interrupt entry for the specified interrupt number and instance

Note	Get the interrupt entry for the specified interrupt number

function QEMUVPBGetSystemCallEntry(Number:LongWord):TSystemCallEntry;

Description: Get the system call entry for the specified system call number

Note	None documented

function QEMUVPBSystemRestart(Delay:LongWord):LongWord;

Description: To be documented

Note	None documented

function QEMUVPBSystemShutdown(Delay:LongWord):LongWord;

Description: To be documented

Note	None documented

function QEMUVPBClockGetCount:LongWord;

Description: Gets the current system clock count (32 least significant bits of total)

Note	On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds and increment the rollover value. Because we return the lower 32 bits then the value returned by this function will rollover to zero every 4295 seconds or about every 71 minutes.

function QEMUVPBClockGetTotal:Int64;

Description: Gets the total system clock count

Note	On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds and increment the rollover value. This is only accurate if either ClockGetCount or ClockGetTotal is called at least once per 178 seconds in order to increment the rollover.

procedure QEMUVPBClockGetTimer(Data:Pointer);

Description: Timer procedure to ensure ClockGetTotal is called at least once per rollover interval

Note	Not intended to be called directly by applications

QEMUVPB thread functions

procedure QEMUVPBSchedulerInit;

Description: Initialize the scheduler interrupt on the boot CPU

Note	None documented

QEMUVPB clock functions

procedure QEMUVPBClockInterrupt(Parameter:Pointer);

Description: Interrupt handler function for the clock interrupt

Note	This schedules another clock interrupt to occur CLOCK_CYCLES_PER_TICK in the future, then updates ClockTicks and ClockSeconds and checks for timers to trigger.

procedure QEMUVPBClockUpdate(Cycles:LongWord; var Last:LongWord);

Description: Setup a clock interrupt to trigger after the specified number of clock cycles

Cycles	Number of cycles after which the timer interrupt is to be triggered
Note	This refers to native clock cycles as specified by CLOCK_FREQUENCY

QEMUVPB scheduler functions

function QEMUVPBSchedulerInterrupt(CPUID:LongWord; Thread:TThreadHandle; Parameter:Pointer):TThreadHandle;

Description: Interrupt handler function for the scheduler interrupt

Note	This schedules another scheduler interrupt to occur SCHEDULER_CLOCKS_PER_INTERRUPT in the future, then checks for threads to wakeup or timeout and the next thread to schedule.

procedure QEMUVPBSchedulerUpdate(Cycles:LongWord; var Last:LongWord);

Description: Setup a scheduler interrupt to trigger after the specified number of clock cycles

Cycles	Number of cycles after which the scheduler interrupt is to be triggered
Note	This refers to native clock cycles as specified by VERSATILEPB_TIMER_FREQUENCY

procedure QEMUVPBSchedulerSystemCall(Request:PSystemCallRequest);

Description: System Call handler for the scheduler

Note	This is registered to receive requests for the SYSTEM_CALL_CONTEXT_SWITCH and will perform a context switch from within an SWI

QEMUVPB framebuffer functions

function QEMUVPBFramebufferDeviceAllocate(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;

Description: Implementation of FramebufferDeviceAllocate API for PL110 Framebuffer

Note	Not intended to be called directly by applications, use FramebufferDeviceAllocate instead.

function QEMUVPBFramebufferDeviceRelease(Framebuffer:PFramebufferDevice):LongWord;

Description: Implementation of FramebufferDeviceRelease API for PL110 Framebuffer

Note	Not intended to be called directly by applications, use FramebufferDeviceRelease instead.

function QEMUVPBFramebufferDeviceBlank(Framebuffer:PFramebufferDevice; Blank:Boolean):LongWord;

Description: Implementation of FramebufferDevicBlank API for PL110 Framebuffer

Note	Not intended to be called directly by applications, use FramebufferDevicBlank instead.

function QEMUVPBFramebufferDeviceCommit(Framebuffer:PFramebufferDevice; Address:PtrUInt; Size,Flags:LongWord):LongWord;

Description: Implementation of FramebufferDeviceCommit API for PL110 Framebuffer

Note	Not intended to be called directly by applications, use FramebufferDeviceCommit instead.

QEMUVPB helper functions

procedure QEMUVPBBootBlink; assembler; nostackframe;

Description: Output characters to UART0 without dependency on any other RTL setup

Note	None documented

procedure QEMUVPBBootOutput(Value:LongWord);

Description: Output characters to UART0 without dependency on any other RTL setup

Note	Based on hexstrings() function by dwelch67 (https://github.com/dwelch67)

procedure QEMUVPBBootConsoleStart;

Description: To be documented

Note	None documented

procedure QEMUVPBBootConsoleWrite(const Value:String);

Description: To be documented

Note	None documented

procedure QEMUVPBBootConsoleWriteEx(const Value:String; X,Y:LongWord);

Description: To be documented

Note	None documented

function QEMUVPBBootConsoleGetX:LongWord;

Description: To be documented

Note	None documented

function QEMUVPBBootConsoleGetY:LongWord;

Description: To be documented

Note	None documented

Return to Unit Reference

`QEMUVPB_PAGE_TABLE_BASE = $00004000;`	Place the first level Page Table after the interrupt vectors at 0x00001000 and before the code start at 0x00010000
`QEMUVPB_PAGE_TABLE_SIZE = SIZE_16K;`	ARMv7 first level Page Table is exactly 16KB in size (4096 32 bit (4 byte) entries)

Difference between revisions of "Unit PlatformQEMUVPB"

Latest revision as of 05:40, 7 April 2023

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

@@ Line 5: / Line 5: @@
 ----
-'''Ultibo Platform interface unit for QEMU VersatilePB'''
+'''Ultibo Platform Interface unit for QEMU VersatilePB'''
-''To be documented''
 === Constants ===
@@ Line 19: / Line 17: @@
 |-
 | <code>QEMUVPB_STARTUP_ADDRESS = $00010000;</code>
-| Address of StartupHandler on Reset
+| Address of StartupHandler on Reset (Obtain from linker)
 |-
 |}
@@ Line 25: / Line 23: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
-<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB page table constants''' <code> QEMUVPB_PAGE_TABLE_* </code></div>
+<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB page table''' <code> QEMUVPB_PAGE_TABLE_* </code></div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
@@ Line 39: / Line 37: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
-<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB vector table constants''' <code> QEMUVPB_VECTOR_TABLE_* </code></div>
+<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB vector table''' <code> QEMUVPB_VECTOR_TABLE_* </code></div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
@@ Line 56: / Line 54: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
-<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB CPU count constants''' <code> QEMUVPB_CPU_* </code></div>
+<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB CPU count''' <code> QEMUVPB_CPU_* </code></div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
@@ Line 73: / Line 71: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
-<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB SWI constants''' <code> QEMUVPB_SWI_* </code></div>
+<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB SWI''' <code> QEMUVPB_SWI_* </code></div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
@@ Line 84: / Line 82: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
-<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB kernel name constants''' <code> QEMUVPB_KERNEL_* </code></div>
+<div style="font-size: 14px; padding-left: 12px;">'''QEMUVPB kernel name''' <code> QEMUVPB_KERNEL_* </code></div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
 | <code>QEMUVPB_KERNEL_NAME = 'kernel.bin';</code>
-| &nbsp;
+| style="width: 50%;"|&nbsp;
 |-
 | <code>QEMUVPB_KERNEL_NAME = 'kernel64.bin';</code>
@@ Line 98: / Line 96: @@
 |-
 | <code>QEMUVPB_KERNEL_COMMAND = '';</code>
+| Not available as a file
+|-
+| <code>QEMUVPB_FIRMWARE_FILES = '';</code>
+| Not available as a file
+|-
+| <code>QEMUVPB_DTB_FILES = '';</code>
 | Not available as a file
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 specific constants''' <code> PL110_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_FRAMEBUFFER_DESCRIPTION = 'ARM PrimeCell PL110 Color LCD';</code>
+| Description of PL110 device
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 mode''' <code> PL110_MODE_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_MODE_UNKNOWN = 0;</code>
+| &nbsp;
+|-
+| <code>PL110_MODE_VGA = 1;</code>
+| Connected to a VGA display
+|-
+| <code>PL110_MODE_SVGA = 2;</code>
+| Connected to a SVGA display
+|-
+| <code>PL110_MODE_TFT = 3;</code>
+| Connected to a TFT display
+|-
+| <code>PL110_MODE_STN = 4;</code>
+| Connected to an STN display
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 register offset''' <code> PL110_CLCD_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_TIMING0 = $00000000;</code>
+| Horizontal Axis Panel Control Register
+|-
+| <code>PL110_CLCD_TIMING1 = $00000004;</code>
+| Vertical Axis Panel Control Register
+|-
+| <code>PL110_CLCD_TIMING2 = $00000008;</code>
+| Clock and Signal Polarity Control Register
+|-
+| <code>PL110_CLCD_TIMING3 = $0000000c;</code>
+| Line End Control Register
+|-
+| <code>PL110_CLCD_UPBASE = $00000010;</code>
+| Upper Panel Frame Base Address Registers
+|-
+| <code>PL110_CLCD_LPBASE = $00000014;</code>
+| Lower Panel Frame Base Address Registers
+|-
+| <code>PL110_CLCD_CONTROL = $00000018;</code>
+| Control Register ''Note: Reversed in VersatilePB implementation, 0x0000001c in PL110 TRM''
+|-
+| <code>PL110_CLCD_IMSC = $0000001c;</code>
+| Interrupt Mask Set/Clear Register ''Note: Reversed in VersatilePB implementation, 0x00000018 in PL110 TRM''
+|-
+| <code>PL110_CLCD_RIS = $00000020;</code>
+| Raw Interrupt Status Register
+|-
+| <code>PL110_CLCD_MIS = $00000024;</code>
+| Masked Interrupt Status Register
+|-
+| <code>PL110_CLCD_ICR = $00000028;</code>
+| Interrupt Clear Register
+|-
+| <code>PL110_CLCD_UPCURR = $0000002C;</code>
+| Upper Panel Current Address Value Registers
+|-
+| <code>PL110_CLCD_LPCURR = $00000030;</code>
+| Lower Panel Current Address Value Registers
+|-
+| <code>PL110_CLCD_PALETTE = $00000200;</code>
+| Color Palette Register
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 CLCD timing0''' <code> PL110_CLCD_TIMING0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_TIMING0_HBP = ($FF shl 24);</code>
+| Horizontal back porch
+|-
+| <code>PL110_CLCD_TIMING0_HFP = ($FF shl 16);</code>
+| Horizontal front porch
+|-
+| <code>PL110_CLCD_TIMING0_HSW = ($FF shl 8);</code>
+| Horizontal synchronization pulse width
+|-
+| <code>PL110_CLCD_TIMING0_PPL = ($FC shl 2);</code>
+| Pixels-per-line (Actual pixels-per-line = 16 * (PPL + 1))
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 CLCD timing1''' <code> PL110_CLCD_TIMING1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_TIMING1_VBP = ($FF shl 24);</code>
+| Vertical back porch
+|-
+| <code>PL110_CLCD_TIMING1_VFP = ($FF shl 16);</code>
+| Vertical front porch
+|-
+| <code>PL110_CLCD_TIMING1_VSW = ($FC shl 10);</code>
+| Vertical synchronization pulse width
+|-
+| <code>PL110_CLCD_TIMING1_LPP = ($3FF shl 0);</code>
+| Lines per panel is the number of active lines per screen (Program to number of lines required minus 1)
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 CLCD timing2''' <code> PL110_CLCD_TIMING2_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_TIMING2_PCD_HI = ($1F shl 27);</code>
+| Upper five bits of Panel Clock Divisor
+|-
+| <code>PL110_CLCD_TIMING2_BCD = (1 shl 26);</code>
+| Bypass pixel clock divider
+|-
+| <code>PL110_CLCD_TIMING2_CPL = ($3FF shl 16);</code>
+| Clocks per line
+|-
+| <code>PL110_CLCD_TIMING2_IOE = (1 shl 14);</code>
+| Invert output enable
+|-
+| <code>PL110_CLCD_TIMING2_IPC = (1 shl 13);</code>
+| Invert panel clock
+|-
+| <code>PL110_CLCD_TIMING2_IHS = (1 shl 12);</code>
+| Invert horizontal synchron
+|-
+| <code>PL110_CLCD_TIMING2_IVS = (1 shl 11);</code>
+| Invert vertical synchronization
+|-
+| <code>PL110_CLCD_TIMING2_ACB = ($1F shl 6);</code>
+| AC bias pin frequency
+|-
+| <code>PL110_CLCD_TIMING2_CLKSEL = (1 shl 5);</code>
+| This bit drives the CLCDCLKSEL signal which is used as the select signal for the external LCD clock multiplexor
+|-
+| <code>PL110_CLCD_TIMING2_PCD_LO = ($1F shl 0);</code>
+| Lower five bits of Panel Clock Divisor
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 CLCD timing3''' <code> PL110_CLCD_TIMING3_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_TIMING3_LEE = (1 shl 16);</code>
+| LCD Line end enable: 0 = CLLE disabled (held LOW)/1 = CLLE signal active
+|-
+| <code>PL110_CLCD_TIMING3_LED = ($3F shl 0);</code>
+| Line-end signal delay from the rising-edge of the last panel clock
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 CLCD control''' <code> PL110_CLCD_CONTROL_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>PL110_CLCD_CONTROL_LCDEN = (1 shl 0);</code>
+| &nbsp;
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP1 = (0 shl 1);</code>
+| LCD bits per pixel: 000 = 1 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP2 = (1 shl 1);</code>
+| LCD bits per pixel: 001 = 2 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP4 = (2 shl 1);</code>
+| LCD bits per pixel: 010 = 4 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP8 = (3 shl 1);</code>
+| LCD bits per pixel: 011 = 8 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP16 = (4 shl 1);</code>
+| LCD bits per pixel: 100 = 16 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP16_565 = (6 shl 1);</code>
+| LCD bits per pixel: 110 = 16 bpp 565 (PL111 only)
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP16_444 = (7 shl 1);</code>
+| LCD bits per pixel: 111 = 16 bpp 444 (PL111 only)
+|-
+| <code>PL110_CLCD_CONTROL_LCDBPP24 = (5 shl 1);</code>
+| LCD bits per pixel: 101 = 24 bpp
+|-
+| <code>PL110_CLCD_CONTROL_LCDBW = (1 shl 4);</code>
+| STN LCD is monochrome (black and white) (0 = STN LCD is color/1 = STN LCD is monochrome)
+|-
+| <code>PL110_CLCD_CONTROL_LCDTFT = (1 shl 5);</code>
+| LCD is TFT (0 = LCD is an STN display, use gray scaler/1 = LCD is TFT, do not use gray scaler)
+|-
+| <code>PL110_CLCD_CONTROL_LCDMONO8 = (1 shl 6);</code>
+| Monochrome LCD has an 8-bit interface (0 = mono LCD uses 4-bit interface/1 = mono LCD uses 8-bit interface)
+|-
+| <code>PL110_CLCD_CONTROL_LCDDUAL = (1 shl 7);</code>
+| LCD interface is dual panel STN (0 = single panel LCD is in use/1 = dual panel LCD is in use)
+|-
+| <code>PL110_CLCD_CONTROL_BGR = (1 shl 8);</code>
+| RGB or BGR format selection (0 = RGB normal output/1 = BGR red and blue swapped.)
+|-
+| <code>PL110_CLCD_CONTROL_BEBO = (1 shl 9);</code>
+| Big-endian byte order (0 = little-endian byte order/1 = big-endian byte order)
+|-
+| <code>PL110_CLCD_CONTROL_BEPO = (1 shl 10);</code>
+| Big-endian pixel ordering within a byte (0 = little-endian pixel ordering within a byte/1= big-endian pixel ordering within a byte)
+|-
+| <code>PL110_CLCD_CONTROL_LCDPWR = (1 shl 11);</code>
+| LCD power enable
+|-
+| <code>PL110_CLCD_CONTROL_LCDVCOMP_VSYNC = (0 shl 12);</code>
+| Generate interrupt at: 00 = start of vertical synchronization
+|-
+| <code>PL110_CLCD_CONTROL_LCDVCOMP_BPORCH = (1 shl 12);</code>
+| Generate interrupt at: 01 = start of back porch
+|-
+| <code>PL110_CLCD_CONTROL_LCDVCOMP_VIDEO = (2 shl 12);</code>
+| Generate interrupt at: 10 = start of active video
+|-
+| <code>PL110_CLCD_CONTROL_LCDVCOMP_FPORCH = (3 shl 12);</code>
+| Generate interrupt at: 11 = start of front porch
+|-
+| <code>PL110_CLCD_CONTROL_LDMAFIFOTIME = (1 shl 15);</code>
+| Unknown
+|-
+| <code>PL110_CLCD_CONTROL_WATERMARK = (1 shl 16);</code>
+| LCD DMA FIFO Watermark level
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 control''' <code> PL110_CONTROL_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_CONTROL_VGA = PL110_CLCD_CONTROL_LCDTFT or PL110_CLCD_CONTROL_LCDVCOMP_BPORCH;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>PL110_CONTROL_SVGA = PL110_CLCD_CONTROL_LCDTFT or PL110_CLCD_CONTROL_LCDVCOMP_BPORCH;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 timing0''' <code> PL110_TIMING0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_TIMING0_VGA = $3F1F3F9C;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>PL110_TIMING0_SVGA = $1313A4C4;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 timing1''' <code> PL110_TIMING1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_TIMING1_VGA = $090B61DF;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>PL110_TIMING1_SVGA = $0505F657;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''PL110 timing2''' <code> PL110_TIMING2_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>PL110_TIMING2_VGA = $067F1800;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>PL110_TIMING2_SVGA = $071F1800;</code>
+| &nbsp;
 |-
 |}
@@ Line 107: / Line 444: @@
 ----
-''To be documented''
+'''PL110 CLCD registers'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PPL110CLCDRegisters = ^TPL110CLCDRegisters;</code>
+<code>TPL110CLCDRegisters = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|Note: Layout of the PL110 registers (See: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0161e/I913915.html)
+|-
+| <code>TIMING0:LongWord;</code>
+| Horizontal Axis Panel Control Register
+|-
+| <code>TIMING1:LongWord;</code>
+| Vertical Axis Panel Control Register
+|-
+| <code>TIMING2:LongWord;</code>
+| Clock and Signal Polarity Control Register
+|-
+| <code>TIMING3:LongWord;</code>
+| Line End Control Register
+|-
+| <code>UPBASE:LongWord;</code>
+| Upper Panel Frame Base Address Registers
+|-
+| <code>LPBASE:LongWord;</code>
+| Lower Panel Frame Base Address Registers
+|-
+| <code>CONTROL:LongWord;</code>
+| Control Register Note: Reversed in VersatilePB implementation, 0x0000001c in PL110 TRM
+|-
+| <code>IMSC:LongWord;</code>
+| Interrupt Mask Set/Clear Register Note: Reversed in VersatilePB implementation, 0x00000018 in PL110 TRM
+|-
+| <code>RIS:LongWord;</code>
+| Raw Interrupt Status Register
+|-
+| <code>MIS:LongWord;</code>
+| Masked Interrupt Status Register
+|-
+| <code>ICR:LongWord;</code>
+| Interrupt Clear Register
+|-
+| <code>UPCURR:LongWord;</code>
+| Upper Panel Current Address Value Registers
+|-
+| <code>LPCURR:LongWord;</code>
+| Lower Panel Current Address Value Registers
+|-
+|}
+</div></div>
+'''PL110 framebuffer'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PPL110Framebuffer = ^TPL110Framebuffer;</code>
+<code>TPL110Framebuffer = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Framebuffer Properties''
+|-
+| <code>Framebuffer:TFramebufferDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''PL110 Properties''
+|-
+| <code>Mode:LongWord;</code>
+| PL110 framebuffer mode (eg PL110_MODE_TFT)
+|-
+| <code>Depth:LongWord;</code>
+| Framebuffer color depth (eg FRAMEBUFFER_DEPTH_16)
+|-
+| <code>Width:LongWord;</code>
+| Framebuffer width in pixels
+|-
+| <code>Height:LongWord;</code>
+| Framebuffer height in pixels
+|-
+| <code>Rotation:LongWord;</code>
+| Framebuffer rotation (eg FRAMEBUFFER_ROTATION_180)
+|-
+|colspan="2"|''Driver Properties''
+|-
+| <code>Control:LongWord;</code>
+| Preset Control register value
+|-
+| <code>Timing0:LongWord;</code>
+| Preset Timing0 register value
+|-
+| <code>Timing1:LongWord;</code>
+| Preset Timing1 register value
+|-
+| <code>Timing2:LongWord;</code>
+| Preset Timing2 register value
+|-
+| <code>Timing3:LongWord;</code>
+| Preset Timing2 register value
+|-
+| <code>Registers:PPL110CLCDRegisters;</code>
+| PL110 registers
+|-
+|}
+</div></div>
+<br />
 === Public variables ===
 ----
-''To be documented''
+'''QEMUVPB specific Ultibo variables'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>QEMUVPBInitialized:Boolean;</code>
+| style="width: 40%;"|
+|-
+|}
+'''Clock variables'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>ClockGetLast:LongWord;</code>
+| style="width: 40%;"|Value of 24MHz Counter on last ClockGetCount or ClockGetTotal call
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>ClockGetBase:Int64;</code>
+| style="width: 40%;"|Base value for 64-bit clock, incremented each time the 24MHz Counter rolls over (Only accurate if ClockGetCount/ClockGetTotal is called at least once per 178 seconds)
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>ClockGetLock:THandle = INVALID_HANDLE_VALUE;</code>
+| style="width: 40%;"|Lock handle for creating 64-bit clock from a 32-bit register
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>ClockGetTimer:THandle = INVALID_HANDLE_VALUE;</code>
+| style="width: 40%;"|Timer handle for ensuring clock is read periodically to maintain accurracy
+|-
+|}
+'''Timer variables'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>Timer0Registers:PSP804TimerRegisters;</code>
+| style="width: 40%;"|Use Timer0 for Clock
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>Timer2Registers:PSP804TimerRegisters;</code>
+| style="width: 40%;"|Use Timer2 for Scheduler
+|-
+|}
+'''Interrupt variables'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>PrimaryInterruptRegisters:PPL190InterruptRegisters;</code>
+| style="width: 40%;"|
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>SecondaryInterruptRegisters:PVersatilePBInterruptRegisters;</code>
+| style="width: 40%;"|
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>InterruptEntries:array[0..(VERSATILEPB_IRQ_COUNT - 1)] of PInterruptEntry;</code>
+| style="width: 40%;"|
+|-
+|}
+'''System call'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>SystemCallEntries:array[0..QEMUVPB_SWI_COUNT - 1] of TSystemCallEntry;</code>
+| style="width: 40%;"|
+|-
+|}
+'''IRQ/FIQ'''
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>IRQEnabled:array[0..1] of LongWord;</code>
+| style="width: 40%;"|2 groups of IRQs to Enable/Disable (See: TPL190InterruptRegisters)
+|-
+|}
+{| class="wikitable" style="font-size: 14px; text-align: left; width: 100%; height: 50px;"
+|-
+| <code>FIQEnabled:array[0..1] of LongWord;</code>
+| style="width: 40%;"|2 groups of FIQs to Enable/Disable (See: TPL190InterruptRegisters)
+|-
+|}
+<br />
 === Function declarations ===
@@ Line 126: / Line 666: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 141: / Line 681: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 153: / Line 693: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 165: / Line 705: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 177: / Line 717: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 189: / Line 729: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 201: / Line 741: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 213: / Line 753: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 225: / Line 765: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| See ??????
+| None documented
 |-
 |}
@@ Line 237: / Line 777: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| CPU to route IRQ to
+| None documented
-|-
-! '''Number'''
-| IRQ number to register
-|-
-! '''Handler'''
-| Interrupt handler function to register
-|-
-! '''HandlerEx'''
-| Extended Interrupt handler function to register
-|-
-! '''Note'''
-| Only one of Handler or HandlerEx can be specified
 |-
 |}
@@ Line 261: / Line 789: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| CPU to route IRQ to
+| None documented
-|-
-! '''Number'''
-| IRQ number to deregister
-|-
-! '''Handler'''
-| Interrupt handler function to deregister
-|-
-! '''HandlerEx'''
-| Extended Interrupt handler function to deregister
-|-
-! '''Note'''
-| Only one of Handler or HandlerEx can be specified
 |-
 |}
@@ Line 285: / Line 801: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| CPU to route FIQ to
+| None documented
-|-
-! '''Number'''
-| FIQ number to register
-|-
-! '''Handler'''
-| Interrupt handler function to register
-|-
-! '''HandlerEx'''
-| Extended Interrupt handler function to register
-|-
-! '''Note'''
-| Only one of Handler or HandlerEx can be specified
 |-
 |}
@@ Line 309: / Line 813: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| CPU to route FIQ to
+| None documented
 |-
-! '''Number'''
+|}
-| FIQ number to deregister
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBRegisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Request registration of the supplied handler to the specified interrupt number (Where Applicable)</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Handler'''
+! Note
-| Interrupt handler function to deregister
+| None documented
 |-
-! '''HandlerEx'''
+|}
-| Extended Interrupt handler function to deregister
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBDeregisterInterrupt(Number,Mask,Priority,Flags:LongWord; Handler:TSharedInterruptHandler; Parameter:Pointer):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Request deregistration of the supplied handler from the specified interrupt number (Where Applicable)</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Only one of Handler or HandlerEx can be specified
+| None documented
 |-
 |}
@@ Line 333: / Line 849: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| The CPU ID to register the System Call against (Ignored on QEMUVPB)
+| None documented
-|-
-! '''Number'''
-| The System Call number to be registered
-|-
-! '''Handler'''
-| The handler function to be registered
-|-
-! '''HandlerEx'''
-| The extended handler function to be registered
-|-
-! '''Note'''
-| Only one of Handler or HandlerEx can be specified
 |-
 |}
@@ Line 357: / Line 861: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''CPUID'''
+! Note
-| The CPU ID to deregister the System Call from (Ignored on QEMUVPB)
+| None documented
-|-
-! '''Number'''
-| The System Call number to be deregistered
-|-
-! '''Handler'''
-| The handler function to be deregistered
-|-
-! '''HandlerEx'''
-| The extended handler function to be deregistered
-|-
-! '''Note'''
-| Only one of Handler or HandlerEx can be specified
 |-
 |}
@@ Line 376: / Line 868: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBGetInterruptEntry(Number:LongWord):TInterruptEntry;</pre>
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBGetInterruptEntry(Number,Instance:LongWord; var Interrupt:TInterruptEntry):LongWord;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the interrupt entry for the specified interrupt number and instance</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | Get the interrupt entry for the specified interrupt number
 |-
@@ Line 393: / Line 885: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 405: / Line 897: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 417: / Line 909: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 429: / Line 921: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds
+| On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds and increment the rollover value. Because we return the lower 32 bits then the value returned by this function will rollover to zero every 4295 seconds or about every 71 minutes.
 |-
 |}
@@ Line 441: / Line 933: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds and increment the rollover value. This is only accurate if either ClockGetCount or ClockGetTotal is called at least once per 178 seconds on order to increment the rollover.
+| On the VersatilePB this comes from the 24MHz counter which will overflow every 178 seconds and increment the rollover value. This is only accurate if either ClockGetCount or ClockGetTotal is called at least once per 178 seconds in order to increment the rollover.
 |-
 |}
 </div></div>
 <br />
-'''QEMUVPB thread functions'''
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBSchedulerInit;</pre>
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBClockGetTimer(Data:Pointer);</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Initialize the scheduler interrupt on the boot CPU</div>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Timer procedure to ensure ClockGetTotal is called at least once per rollover interval</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| None documented
+| Not intended to be called directly by applications
 |-
 |}
@@ Line 463: / Line 952: @@
 <br />
-'''QEMUVPB IRQ functions'''
+'''QEMUVPB thread functions'''
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBDispatchIRQ(CPUID:LongWord; Thread:TThreadHandle):TThreadHandle;</pre>
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBSchedulerInit;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Process any pending IRQ requests</div>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Initialize the scheduler interrupt on the boot CPU</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Called by ARMv7/8IRQHandler in PlatformARMv7/8
-A DataMemoryBarrier is executed before and after calling this function
-|-
-|}
-</div></div>
-<br />
-<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBHandleIRQ(Number,CPUID:LongWord; Thread:TThreadHandle):TThreadHandle;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Call the handler function for an IRQ that was received, or halt if it doesn't exist</div>
-<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
-{| class="wikitable" style="font-size: 14px; background: white;"
-|-
-! '''Note'''
 | None documented
-|-
-|}
-</div></div>
-<br />
-'''QEMUVPB FIQ functions'''
-<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBDispatchFIQ(CPUID:LongWord; Thread:TThreadHandle):TThreadHandle;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Process any pending FIQ requests</div>
-<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
-{| class="wikitable" style="font-size: 14px; background: white;"
-|-
-! '''Note'''
-| Called by ARMv7/8FIQHandler in PlatformARMv7/8
-A DataMemoryBarrier is executed before and after calling this function
-|-
-|}
-</div></div>
-<br />
-<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBHandleFIQ(Number,CPUID:LongWord; Thread:TThreadHandle):TThreadHandle;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Call the handler function for an FIQ that was received, or halt if it doesn't exist</div>
-<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
-{| class="wikitable" style="font-size: 14px; background: white;"
-|-
-! '''Note'''
-| None documented
-|-
-|}
-</div></div>
-<br />
-'''QEMUVPB SWI functions'''
-<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBDispatchSWI(CPUID:LongWord; Thread:TThreadHandle; Request:PSystemCallRequest):TThreadHandle;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Process an SWI request</div>
-<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
-{| class="wikitable" style="font-size: 14px; background: white;"
-|-
-! '''Note'''
-| Called by ARMv7/8SoftwareInterruptHandler in PlatformARMv7/8
-A DataMemoryBarrier is executed before and after calling this function
 |-
 |}
@@ Line 543: / Line 975: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | This schedules another clock interrupt to occur CLOCK_CYCLES_PER_TICK in the future, then updates ClockTicks and ClockSeconds and checks for timers to trigger.
 |-
@@ Line 555: / Line 987: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Cycles'''
+! Cycles
 | Number of cycles after which the timer interrupt is to be triggered
 |-
-! '''Note'''
+! Note
 | This refers to native clock cycles as specified by CLOCK_FREQUENCY
 |-
@@ Line 573: / Line 1,005: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | This schedules another scheduler interrupt to occur SCHEDULER_CLOCKS_PER_INTERRUPT in the future, then checks for threads to wakeup or timeout and the next thread to schedule.
 |-
@@ Line 585: / Line 1,017: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Cycles'''
+! Cycles
 | Number of cycles after which the scheduler interrupt is to be triggered
 |-
-! '''Note'''
+! Note
 | This refers to native clock cycles as specified by VERSATILEPB_TIMER_FREQUENCY
 |-
@@ Line 600: / Line 1,032: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | This is registered to receive requests for the SYSTEM_CALL_CONTEXT_SWITCH and will perform a context switch from within an SWI
 |-
@@ Line 615: / Line 1,047: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Not intended to be called directly by applications, use FramebufferDeviceAllocate instead
+| Not intended to be called directly by applications, use FramebufferDeviceAllocate instead.
 |-
 |}
@@ Line 627: / Line 1,059: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Not intended to be called directly by applications, use FramebufferDeviceRelease instead
+| Not intended to be called directly by applications, use FramebufferDeviceRelease instead.
 |-
 |}
@@ Line 639: / Line 1,071: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Not intended to be called directly by applications, use FramebufferDevicBlank instead
+| Not intended to be called directly by applications, use FramebufferDevicBlank instead.
 |-
 |}
@@ Line 646: / Line 1,078: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBFramebufferDeviceCommit(Framebuffer:PFramebufferDevice; Address,Size,Flags:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBFramebufferDeviceCommit(Framebuffer:PFramebufferDevice; Address:PtrUInt; Size,Flags:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceCommit API for PL110 Framebuffer</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Not intended to be called directly by applications, use FramebufferDeviceCommit instead
+| Not intended to be called directly by applications, use FramebufferDeviceCommit instead.
 |-
 |}
 </div></div>
 <br />
+'''QEMUVPB helper functions'''
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function QEMUVPBFramebufferDeviceSetProperties(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootBlink; assembler; nostackframe;</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceSetProperties API for PL110 Framebuffer</div>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Output characters to UART0 without dependency on any other RTL setup</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Not intended to be called directly by applications, use FramebufferDeviceSetProperties instead
+| None documented
 |-
 |}
 </div></div>
 <br />
-'''QEMUVPB helper functions'''
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootBlink; assembler; nostackframe;</pre>
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootOutput(Value:LongWord);</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' Output characters to UART0 without dependency on any other RTL setup</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
+| Based on hexstrings() function by dwelch67 (https://github.com/dwelch67)
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootConsoleStart;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
 | None documented
 |-
@@ Line 685: / Line 1,129: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootOutput(Value:LongWord);</pre>
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootConsoleWrite(const Value:String);</pre>
-<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Output characters to UART0 without dependency on any other RTL setup</div>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Based on hexstrings() function by dwelch67 (https://github.com/dwelch67)
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure QEMUVPBBootConsoleWriteEx(const Value:String; X,Y:LongWord);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBBootConsoleGetX:LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function QEMUVPBBootConsoleGetY:LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
 |-
 |}