Difference between revisions of "Unit BCM2708"

Latest revision as of 06:19, 11 April 2025

Both devices support 3 chip selects, by default SPI1 is available on GPIO pins 16 to 21 (CS2, CS1, CS0, MISO, MOSI, SCLK) using alternate function 4 and SPI2 is available on GPIO pins 40 to 45 (MISO, MOSI, SCLK, CS0, CS1, CS2) using alternate function 4. Only pins 16 to 21 are available on the header and only on the 40 pin header of the Raspberry Pi A+/B+/Zero/2B/3B.

BCM2708 SPI/I2C Slave Device

The slave device can be used as either an I2C or an SPI interface, the I2C slave supports 400KHz fast mode operation. Only 7 bit addressing is supported, DMA is not supported and neither is clock stretching.

Note: On the Raspberry Pi A+/B+/Zero/2B/3B the SPI slave device is apparently faulty and cannot be used.

The I2C Slave device can only appear on GPIO pins 18 (SDA) and 19 (SCL) (Alternate function 3).

BCM2708 DMA Device

The DMA controller has 16 channels in total although not all are available for software to use as some are already used by the GPU.

The firmware will pass the value dma.dmachans on the command line which will indicate which channels are available for our use.

Channels 0 to 6 are normal channels which support 2D stride and transfers up to 1GB per control block

Channels 7 to 14 are Lite channels which do not support stride and only allow transfers up to 64KB per control block

Channel 15 is not mentioned in most documentation and is shown as not available in the mask passed in dma.dmachans

Channel 0 and 15 are Bulk channels which have an additional FIFO for faster transfers (8 beat burst per read)

BCM2708 PWM0/1 Device

The BCM2708 has a single PWM controller with 2 independent output bit streams with multiple algorithms for generating the output pulse. The PWM controller supports either a single data register (independent per channel) or a 16 x 32 FIFO which also supports DMA mode transmission.

On the Raspberry Pi PWM0 and PWM1 are also connected via GPIO pins 40 and 45 (40 and 41 on the Raspberry Pi 3B) to the audio circuit and allow playback of digital audio signals via the 3 or 4 pole line jack (depending on model).

PWM0 is available on GPIO pins 12 (function 0), 18 (function 5), 40 (function 0) and 52 (function 1).

PWM1 is available on GPIO pins 13 (function 0), 19 (function 5), 41, 45 (function 0) and 53 (function 1).

On the Raspberry Pi A and B only pin 18 is exposed on the 26 pin header.

On the Raspberry Pi A+/B+/Zero/2B/3B pins 12, 13, 18 and 19 are exposed on the 40 pin header.

BCM2708 GPIO Device

The GPIO has 54 pins available each with multiple alternate functions. All pins can be configured as input or output and all can have pull up or down applied.

Not all pins are exposed on the 26 or 40 pin header of the Raspberry Pi, for details of which pins are available see:

Raspberry Pi A and B - https://www.raspberrypi.org/documentation/usage/gpio/README.md

Raspberry Pi A+/B+/2B/3B/Zero - https://www.raspberrypi.org/documentation/usage/gpio-plus-and-raspi2/README.md

Some of the 54 pins are used for peripheral communication (such as the SD card) and are not available for general use, take care when changing function selects on pins to avoid disabling certain system peripherals.

Event detection can be enabled for both high and low levels as well as rising and falling edges, there is also an asynchronous rising or falling edge detection which can detect edges of very short duration.

BCM2708 UART0 Device

The UART0 device is an ARM PL011 UART which supports programmable baud rates, start, stop and parity bits and hardware flow control and many others. The UART0 is similar to the industry standard 16C650 but with a number of differences, the PL011 has some optional features such as IrDA, Serial InfraRed and DMA which are not supported by the Broadcom implementation. In the standard configuration the UART0 TX and RX lines are connected to GPIO pins 14 and 15 respectively (Alternate function 0) but they can be remapped via GPIO function selects to a number of other locations. On the Raspberry Pi (all models) none of these alternate pin mappings are exposed via the 26 or 40 pin header and therefore cannot be used easily. This means that UART0 and UART1 cannot be used at the same time.

On the Raspberry Pi 3B the UART0 can be mapped to GPIO pins 32 and 33 (Alternate function 3) to communicate with the built in Bluetooth module.

BCM2708 UART1 Device

The UART1 device is a Broadcom implementation that is part of the AUX device which also includes the SPI1 and SPI2 devices. This device is termed a Mini UART and has a smaller feature set than the PL011 UART but still supports a fairly standard communication protocol with programmable baud rate and hardware flow control.

The Mini UART is similar to the standard 16550 device but is missing some of the features, the device also has no DMA support so high speed transfers will produce a higher CPU load. In the standard configuration the UART1 TX and RX lines are connected to GPIO pins 14 and 15 respectively (Alternate function 5) but they can be remapped via GPIO function selects to a number of other locations. On the Raspberry Pi (all models) none of these alternate pin mappings are exposed via the 26 or 40 pin header and therefore cannot be used easily. This means that UART0 and UART1 cannot be used at the same time.

On the Raspberry Pi 3B the UART1 can be mapped to GPIO pins 32 and 33 (Alternate function 5) to communicate with the built in Bluetooth module.

BCM2708 SDHCI Device

The SDHCI controller on the BCM2708 is an Arasan SD Host controller.

The Card Detect pin is connected to GPIO pin 47 (on the RPi Model A/B)(Not connected on the RPi Model A+/B+)

The Write Protect pin is not connected.

The device can be routed to GPIO pins 22 to 27 (ALT3) or 48 to 53 (ALT3), it can also be routed to GPIO pins 34 to 39 (ALT3) to provide an SDIO controller for the on board WiFi.

BCM2708 SDHOST Device

The SDHOST controller on the BCM2708 is a non SDHCI-compliant device which requires a specific driver.

It can be routed to GPIO pins 22 to 27 (ALT0) or 48 to 53 (ALT0) in order to control the SD card slot when the SDHCI device is being used for the on board WiFi.

Note: The actual driver is implemented in the BCMSDHOST unit.

BCM2708 Clock (System Timer) Device

The clock device in the BCM2708 is based on the System Timer which is a 64 bit free running counter that runs at 1MHz regardless of core or CPU clock speeds. The System Timer cannot be stopped and the counter cannot be set or reset.

The System Timer includes 4 compare registers which can each generate an interrupt when the compare value is matched, however 2 of the 4 are consumed by the GPU and on the Raspberry Pi A/B/A+/B+/Zero the other 2 are used for the scheduler and clock interrupts in Ultibo.

This device simply exposes the free running counter as a clock value and does not provide access to the timer compare functionality or to interrupt based events, for those see the timer devices below.

BCM2708 Clock (ARM Timer) Device

This device represents that free running counter from the ARM Timer device (below) as a clock device. The free running counter does not appear in the original SP804 timer. The counter is 32 bits wide and has its own divider that is 8 bits wide meaning that it can be set to clock rates of between 975KHz and 250MHz (or 1.5MHz to 400MHz on the Raspberry Pi 3B).

The counter does not generate an interrupt and cannot be set or reset but it can be stopped and started.

BCM2708 ARM Timer Device

The ARM Timer device in the BCM2708 is based on the ARM SP804 timer with some modifications and additions. In the Raspberry Pi it is connected to the core clock which by default is 250MHz but was increased to 400MHz on the Raspberry Pi 3B.

The divider is 10 bits wide which means that the ARM Timer can be set to clock rates of between 250KHz and 250MHz (or 400KHz to 400MHz on the Raspberry Pi 3B). Both the counter and the load/reload value are 32 bits wide by default giving a wide range of tick intervals.

The ARM Timer features a free running counter which is not enabled or used by this driver and a down counter which operates in wrapping mode so that each time it reaches 0 it triggers an interrupt and reloads the value from a load or reload register to begin counting again.

@@ Line 4: / Line 4: @@
 === Description ===
 ----
+'''Ultibo BCM2708 Interface unit'''
 This unit provides the BCM2708 specific implementations of the following devices:
@@ Line 10: / Line 12: @@
 *I2C0
 *I2C1
+*I2C2
 *SPI1
 *SPI2
@@ Line 41: / Line 44: @@
 By default SPI0 can appear on GPIO pins 7 to 11 (CS1, CS0, MISO, MOSI, SCLK) using alternate function 0 or on GPIO pins 35 to 39 (CS1, CS0, MISO, MOSI, SCLK) using alternate function 0, only pins 7 to 11 are available on the header.
-'''BCM2708 I2C0/1 Device'''
+'''BCM2708 I2C0/1/2 Device'''
 The BCM2708 has 3 Broadcom Serial Controller (BSC) devices which are fast mode (400Kz) masters numbered BSC0, BSC1 and BSC2.
-Device BSC2 is dedicated to the HDMI interface and is not availale for use by the ARM processor. All BSC devices contain a 16 byte FIFO, support 7 bit and 10 bit addressing and have software configurable clock timing.
+Device BSC2 is dedicated to the HDMI interface but can be accessed by the ARM processor for controlling some HDMI functionality. All BSC devices contain a 16 byte FIFO, support 7 bit and 10 bit addressing and have software configurable clock timing.
 By default BSC0 can appear on GPIO pins 0 and 1 (Alternate function 0), 28 and 29 (Alternate function 0) or 44 and 45 (Alternate function 1). Unfortunately on all except the Revision 1 models none of these pins are available on the 26 or 40 pin header.
@@ Line 58: / Line 61: @@
 Both devices support 3 chip selects, by default SPI1 is available on GPIO pins 16 to 21 (CS2, CS1, CS0, MISO, MOSI, SCLK) using alternate function 4 and SPI2 is available on GPIO pins 40 to 45 (MISO, MOSI, SCLK, CS0, CS1, CS2) using alternate function 4. Only pins 16 to 21 are available on the header and only on the 40 pin header of the Raspberry Pi A+/B+/Zero/2B/3B.
+'''BCM2708 SPI/I2C Slave Device'''
+The slave device can be used as either an I2C or an SPI interface, the I2C slave supports 400KHz fast mode operation. Only 7 bit addressing is supported, DMA is not supported and neither is clock stretching.
+Note: On the Raspberry Pi A+/B+/Zero/2B/3B the SPI slave device is apparently faulty and cannot be used.
+The I2C Slave device can only appear on GPIO pins 18 (SDA) and 19 (SCL) (Alternate function 3).
 '''BCM2708 DMA Device'''
@@ Line 85: / Line 96: @@
 On the Raspberry Pi A and B only pin 18 is exposed on the 26 pin header.
-On the Raspberry Pi A+/B+/Zero/2B/3B pins 12, 18 and 19 are exposed on the 40 pin header.
+On the Raspberry Pi A+/B+/Zero/2B/3B pins 12, 13, 18 and 19 are exposed on the 40 pin header.
 '''BCM2708 GPIO Device'''
@@ Line 97: / Line 108: @@
 Raspberry Pi A+/B+/2B/3B/Zero - https://www.raspberrypi.org/documentation/usage/gpio-plus-and-raspi2/README.md
-Some of the 54 pins are used for peripheral communication (such as the SD card) and are not available for general use,take care when changing function selects on pins to avoid disabling certain system peripherals.
+Some of the 54 pins are used for peripheral communication (such as the SD card) and are not available for general use, take care when changing function selects on pins to avoid disabling certain system peripherals.
 Event detection can be enabled for both high and low levels as well as rising and falling edges, there is also an asynchronous rising or falling edge detection which can detect edges of very short duration.
@@ Line 103: / Line 114: @@
 '''BCM2708 UART0 Device'''
-The UART0 device is an ARM PL011 UART which supports programmable baud rates, start, stop and parity bits and hardware flow control and many others. The UART0 is similar to the industry standard 16C650 but with a number of differences, the PL011 has a some optional features such as IrDA, Serial InfraRed and DMA which are not supported by the Broadcom implementation. In the standard configuration the UART0 TX and RX lines are connected to GPIO pins 14 and 15 respectively (Alternate function 0) but they can be remapped via GPIO function selects to a number of other locations. On the Raspberry Pi (all models) none of these alternate pin mappings are exposed via the 26 or 40 pin header and therefore cannot be used easily. This means that UART0 and UART1 cannot be used at the same time.
+The UART0 device is an ARM PL011 UART which supports programmable baud rates, start, stop and parity bits and hardware flow control and many others. The UART0 is similar to the industry standard 16C650 but with a number of differences, the PL011 has some optional features such as IrDA, Serial InfraRed and DMA which are not supported by the Broadcom implementation. In the standard configuration the UART0 TX and RX lines are connected to GPIO pins 14 and 15 respectively (Alternate function 0) but they can be remapped via GPIO function selects to a number of other locations. On the Raspberry Pi (all models) none of these alternate pin mappings are exposed via the 26 or 40 pin header and therefore cannot be used easily. This means that UART0 and UART1 cannot be used at the same time.
 On the Raspberry Pi 3B the UART0 can be mapped to GPIO pins 32 and 33 (Alternate function 3) to communicate with the built in Bluetooth module.
@@ Line 121: / Line 132: @@
 The Card Detect pin is connected to GPIO pin 47 (on the RPi Model A/B)(Not connected on the RPi Model A+/B+)
-The Write Protect pin is not connected on any RPi model.
+The Write Protect pin is not connected.
-'''BCM2708 Clock Device'''
+The device can be routed to GPIO pins 22 to 27 (ALT3) or 48 to 53 (ALT3), it can also be routed to GPIO pins 34 to 39 (ALT3) to provide an SDIO controller for the on board WiFi.
-The clock device in the BCM2708 is based on the System Timer which is a 64 bit free running counter that runs at 1MHz regardless of core or CPU clock speeds.
+'''BCM2708 SDHOST Device'''
+The SDHOST controller on the BCM2708 is a non SDHCI-compliant device which requires a specific driver.
+It can be routed to GPIO pins 22 to 27 (ALT0) or 48 to 53 (ALT0) in order to control the SD card slot when the SDHCI device is being used for the on board WiFi.
+Note: The actual driver is implemented in the BCMSDHOST unit.
+'''BCM2708 Clock (System Timer) Device'''
+The clock device in the BCM2708 is based on the System Timer which is a 64 bit free running counter that runs at 1MHz regardless of core or CPU clock speeds. The System Timer cannot be stopped and the counter cannot be set or reset.
 The System Timer includes 4 compare registers which can each generate an interrupt when the compare value is matched, however 2 of the 4 are consumed by the GPU and on the Raspberry Pi A/B/A+/B+/Zero the other 2 are used for the scheduler and clock interrupts in Ultibo.
 This device simply exposes the free running counter as a clock value and does not provide access to the timer compare functionality or to interrupt based events, for those see the timer devices below.
+'''BCM2708 Clock (ARM Timer) Device'''
+This device represents that free running counter from the ARM Timer device (below) as a clock device. The free running counter does not appear in the original SP804 timer. The counter is 32 bits wide and has its own divider that is 8 bits wide meaning that it can be set to clock rates of between 975KHz and 250MHz (or 1.5MHz to 400MHz on the Raspberry Pi 3B).
+The counter does not generate an interrupt and cannot be set or reset but it can be stopped and started.
 '''BCM2708 ARM Timer Device'''
@@ Line 137: / Line 164: @@
 The divider is 10 bits wide which means that the ARM Timer can be set to clock rates of between 250KHz and 250MHz (or 400KHz to 400MHz on the Raspberry Pi 3B). Both the counter and the load/reload value are 32 bits wide by default giving a wide range of tick intervals.
-The ARM Timer features a free running counter which is not enabled or used by this driver and a down counter which operates in wrapping mode so that each time it reaches 0 it triggers an interrupt and reloads the value ?rom a load or reload register to begin counting again.
+The ARM Timer features a free running counter which is not enabled or used by this driver and a down counter which operates in wrapping mode so that each time it reaches 0 it triggers an interrupt and reloads the value from a load or reload register to begin counting again.
 === Constants ===
 ----
-''To be documented''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SPI0''' <code> BCM2708_SPI0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SPI0_DESCRIPTION = 'BCM2835 SPI0 Master';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SPI0_MAX_SIZE = $FFFF;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SPI0_MIN_CLOCK = 3814;</code>
+| Default minimum based on the default settings from the firmware (Recalculated during open)
+|-
+| <code>BCM2708_SPI0_MAX_CLOCK = 125000000;</code>
+| Default maximum based on the default settings from the firmware (Recalculated during open)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SPI0_MIN_DIVIDER = 2;</code>
+| Divider is always rounded down to an even number and a value of 0 sets the divider to 65536
+|-
+| <code>BCM2708_SPI0_MAX_DIVIDER = $FFFE;</code>
+| Divider is always rounded down to an even number
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SPI0_CORE_CLOCK = 250000000;</code>
+| Default core clock based on the default settings from the firmware (Requested from firmware during start)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SPI0_MODE_IRQ = 0;</code>
+| &nbsp;
+|-
+| <code>BCM2708_SPI0_MODE_DMA = 1;</code>
+| &nbsp;
+|-
+| <code>BCM2708_SPI0_MODE_PIO = 2;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 BSCI2C (BSC0/1/2)''' <code> BCM2708_BSCI2C_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_BSCI2C_MAX_SIZE = $FFFF;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_BSCI2C_MIN_CLOCK = 3814;</code>
+| Default minimum based on the default settings from the firmware (Recalculated during open)
+|-
+| <code>BCM2708_BSCI2C_MAX_CLOCK = 125000000;</code>
+| Default maximum based on the default settings from the firmware (Recalculated during open)
+|-
+| <code>BCM2708_BSCI2C_DEFAULT_CLOCK = 100000;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_BSCI2C_MIN_DIVIDER = 2;</code>
+| Divider is always rounded down to an even number and a value of 0 sets the divider to 32768
+|-
+| <code>BCM2708_BSCI2C_MAX_DIVIDER = $FFFE;</code>
+| Divider is always rounded down to an even number
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_BSCI2C_CORE_CLOCK = 250000000;</code>
+| Default core clock based on the default settings from the firmware (Requested from firmware during start)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_BSCI2C_MODE_WRITE = 0;</code>
+| &nbsp;
+|-
+| <code>BCM2708_BSCI2C_MODE_READ = 1;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 I2C0 (BSC0)''' <code> BCM2708_I2C0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_I2C0_DESCRIPTION = 'BCM2835 BSC0 Master I2C';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 I2C1 (BSC1)''' <code> BCM2708_I2C1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_I2C1_DESCRIPTION = 'BCM2835 BSC1 Master I2C';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 I2C2 (BSC2)''' <code> BCM2708_I2C2_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_I2C2_DESCRIPTION = 'BCM2835 BSC2 Master I2C';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SPI1''' <code> BCM2708_SPI1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SPI1_DESCRIPTION = 'BCM2835 AUX SPI1 Master';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SPI2''' <code> BCM2708_SPI2_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SPI2_DESCRIPTION = 'BCM2835 AUX SPI2 Master';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 I2C slave''' <code> BCM2708_I2CSLAVE_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_I2CSLAVE_DESCRIPTION = 'BCM2835 I2C Slave';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_I2CSLAVE_TIMEOUT = 10;</code>
+| Timeout (Milliseconds) for RX/TX wait data
+|-
+| <code>BCM2708_I2CSLAVE_BUFFER_SIZE = 1024;</code>
+| Size in bytes of the RX/TX data buffer
+|-
+| <code>BCM2708_I2CSLAVE_RX_POLL_LIMIT = 256;</code>
+| Number of times interrupt handler may poll the read FIFO
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SPI slave''' <code> BCM2708_SPISLAVE_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SPISLAVE_DESCRIPTION = 'BCM2835 SPI Slave';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 DMA''' <code> BCM2708_DMA_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_DMA_DESCRIPTION = 'BCM2835 DMA';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_CHANNEL_COUNT = 16;</code>
+| Total number of DMA channels (Not all are usable)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_LITE_CHANNELS   = $7F80;</code>
+| Mask of DMA Lite channels (7 to 14)
+|-
+| <code>BCM2708_DMA_NORMAL_CHANNELS = $007E; {807F}</code>
+| Mask of normal channels (1 to 6)
+|-
+| <code>BCM2708_DMA_BULK_CHANNELS   = $8001;</code>
+| Mask of DMA Bulk channels (0 and 15)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_SHARED_CHANNELS = $7800;</code>
+| Mask of channels with shared interrupt (11 to 14)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_MAX_LITE_TRANSFER = 65536;</code>
+| Maximum transfer length for a DMA Lite channel
+|-
+| <code>BCM2708_DMA_MAX_NORMAL_TRANSFER = 1073741824;</code>
+| Maximum transfer length for a normal channel
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_MAX_STRIDE = $FFFF;</code>
+| Maximum stride value (Increment between rows) (Note this is a signed value (Min -32768/Max 32767)
+|-
+| <code>BCM2708_DMA_MAX_Y_COUNT = $3FFF;</code>
+| Maximum number of X length transfers in 2D stride
+|-
+| <code>BCM2708_DMA_MAX_X_LENGTH = $FFFF;</code>
+| Maximum X transfer length in 2D stride
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_CB_ALIGNMENT = 32;</code>
+| Alignment required for DMA control blocks
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_DMA_LITE_BURST_LENGTH = 2;</code>
+| Burst length for DMA Lite channels
+|-
+| <code>BCM2708_DMA_NORMAL_BURST_LENGTH = 4;</code>
+| Burst length for normal channels
+|-
+| <code>BCM2708_DMA_BULK_BURST_LENGTH = 16;</code>
+| Burst length for DMA Bulk channels
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 PWM''' <code> BCM2708_PWM_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_PWM_MIN_PERIOD = 108;</code>
+| Default based on 19.2MHz PWM clock (Oscillator source)
+|-
+| <code>BCM2708_PWM_DEFAULT_CLOCK = 19200000;</code>
+| Default to the 19.2MHz oscillator clock
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 PWM0''' <code> BCM2708_PWM0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_PWM0_DESCRIPTION = 'BCM2835 PWM0';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 PWM1''' <code> BCM2708_PWM1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_PWM1_DESCRIPTION = 'BCM2835 PWM1';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 GPIO''' <code> BCM2708_GPIO_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_GPIO_DESCRIPTION = 'BCM2835 GPIO';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_GPIO_MIN_PIN = GPIO_PIN_0;</code>
+| &nbsp;
+|-
+| <code>BCM2708_GPIO_MAX_PIN = GPIO_PIN_53;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_GPIO_MAX_LEVEL = GPIO_LEVEL_HIGH;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_GPIO_MAX_PULL = GPIO_PULL_DOWN;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_GPIO_MIN_FUNCTION = GPIO_FUNCTION_IN;</code>
+| &nbsp;
+|-
+| <code>BCM2708_GPIO_MAX_FUNCTION = GPIO_FUNCTION_ALT5;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_GPIO_MIN_TRIGGER = GPIO_TRIGGER_LOW;</code>
+| &nbsp;
+|-
+| <code>BCM2708_GPIO_MAX_TRIGGER = GPIO_TRIGGER_ASYNC_FALLING;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+|colspan="2"|''GPIO pull up/down to BCM2835 pull up/down''
+|-
+|colspan="2"|<code>BCM2708_GPIO_PULL_MAP:array[GPIO_PULL_NONE..GPIO_PULL_DOWN] of LongWord = (</code>
+|-
+| <code>BCM2835_GPPUD_NONE,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPPUD_UP,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPPUD_DOWN);</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+|colspan="2"|''GPIO functions to BCM2835 functions''
+|-
+|colspan="2"|<code>BCM2708_GPIO_FUNCTION_MAP:array[BCM2708_GPIO_MIN_FUNCTION..BCM2708_GPIO_MAX_FUNCTION] of LongWord = (</code>
+|-
+| <code>BCM2835_GPFSEL_IN,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_OUT,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT1,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT2,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT3,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT4,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFSEL_ALT5);</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+|colspan="2"|''BCM2835 functions to GPIO functions''
+|-
+|colspan="2"|<code>BCM2708_GPIO_FUNCTION_UNMAP:array[BCM2708_GPIO_MIN_FUNCTION..BCM2708_GPIO_MAX_FUNCTION] of LongWord = (</code>
+|-
+| <code>GPIO_FUNCTION_IN,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_OUT,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT5,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT4,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT0,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT1,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT2,</code>
+| &nbsp;
+|-
+| <code>GPIO_FUNCTION_ALT3);</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+|colspan="2"|''GPIO triggers to BCM2835 event registers''
+|-
+|colspan="2"|<code>BCM2708_GPIO_TRIGGER_MAP:array[BCM2708_GPIO_MIN_TRIGGER..BCM2708_GPIO_MAX_TRIGGER] of LongWord = (</code>
+|-
+| <code>GPIO_FUNCTION_IN,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPLEN0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPHEN0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPREN0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPFEN0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPAREN0,</code>
+| &nbsp;
+|-
+| <code>BCM2835_GPAFEN0);</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 UART0 (PL011)''' <code> BCM2708_UART0_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_UART0_DESCRIPTION = 'BCM2835 PL011 UART';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_MIN_BAUD = 300;</code>
+| Default minimum of 300 baud
+|-
+| <code>BCM2708_UART0_MAX_BAUD = 187500;</code>
+| Default maximum based on the default settings from the firmware (Recalculated during open)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_MIN_DATABITS = SERIAL_DATA_5BIT;</code>
+| &nbsp;
+|-
+| <code>BCM2708_UART0_MAX_DATABITS = SERIAL_DATA_8BIT;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_MIN_STOPBITS = SERIAL_STOP_1BIT;</code>
+| &nbsp;
+|-
+| <code>BCM2708_UART0_MAX_STOPBITS = SERIAL_STOP_2BIT;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_MAX_PARITY = SERIAL_PARITY_EVEN;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_MAX_FLOW = SERIAL_FLOW_RTS_CTS;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code> BCM2708_UART0_CLOCK_RATE = 3000000;</code>
+| Default clock rate based on the default settings from the firmware (Requested from firmware during open)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_UART0_RX_POLL_LIMIT = 256;</code>
+| Number of times interrupt handler may poll the read FIFO
+|-
+| <code>BCM2708_UART0_RX_BUFFER_SIZE = 1024;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 UART1 (AUX)''' <code> BCM2708_UART1_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_UART1_DESCRIPTION = 'BCM2835 AUX (Mini) UART';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SDHCI''' <code> BCM2708_EMMC_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_EMMC_DESCRIPTION = 'BCM2835 Arasan SD Host';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_EMMC_MIN_FREQ = 400000;</code>
+| Default minimum of 400KHz
+|-
+| <code>BCM2708_EMMC_MAX_FREQ = 200000000;</code>
+| Default clock rate based on the default settings from the firmware (Requested from firmware during start)
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 SDHOST''' <code> BCM2708_SDHOST_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SDHOST_DESCRIPTION = 'BCM2835 SDHOST';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_SDHOST_MIN_FREQ = 400000;</code>
+| Default minimum of 400KHz
+|-
+| <code>BCM2708_SDHOST_MAX_FREQ = 250000000;</code>
+| Default clock rate based on the default settings from the firmware (Requested from firmware during start)
+|-
+|colspan="2"|See: BCMSDHOST for the driver implementation
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 clock (system timer)''' <code> BCM2708_SYS_CLOCK_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_SYS_CLOCK_DESCRIPTION = 'BCM2835 System Timer Clock';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 clock (ARM timer)''' <code> BCM2708_ARM_CLOCK_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_ARM_CLOCK_DESCRIPTION = 'BCM2835 ARM Timer Clock';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_CLOCK_MIN_RATE = 976562;</code>
+| Default minimum (Divider 255) based on the default settings from the firmware (Recalculated during start)
+|-
+| <code>BCM2708_ARM_CLOCK_MAX_RATE = 250000000;</code>
+| Default maximum (Divider 0) based on the default settings from the firmware (Recalculated during start)
+|-
+| <code>BCM2708_ARM_CLOCK_DEFAULT_RATE = 3968253;</code>
+| Default rate (Divider 62) based on the default settings from the firmware (Recalculated during start)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_CLOCK_MIN_DIVIDER = 0;</code>
+| &nbsp;
+|-
+| <code>BCM2708_ARM_CLOCK_MAX_DIVIDER = 255;</code>
+| &nbsp;
+|-
+| <code>BCM2708_ARM_CLOCK_DEFAULT_DIVIDER = 62;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_CLOCK_CORE_CLOCK = 250000000;</code>
+| Default core clock based on the default settings from the firmware (Requested from firmware during start)
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 ARM timer''' <code> BCM2708_ARM_TIMER_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_ARM_TIMER_DESCRIPTION = 'BCM2835 ARM Timer';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_MIN_RATE = 244140;</code>
+| Default minimum (Divider 1023) based on the default settings from the firmware (Recalculated during start)
+|-
+| <code>BCM2708_ARM_TIMER_MAX_RATE = 250000000;</code>
+| Default maximum (Divider 0) based on the default settings from the firmware (Recalculated during start)
+|-
+| <code>BCM2708_ARM_TIMER_DEFAULT_RATE = 1000000;</code>
+| Default rate (Divider 249) based on the default settings from the firmware (Recalculated during start)
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_MIN_INTERVAL = 1;</code>
+| &nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_MAX_INTERVAL = $FFFFFFFF;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_MIN_DIVIDER = 0;</code>
+| &nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_MAX_DIVIDER = 1023;</code>
+| &nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_DEFAULT_DIVIDER = 249;</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_ARM_TIMER_CORE_CLOCK = 250000000;</code>
+| Default core clock based on the default settings from the firmware (Requested from firmware during start)
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 random''' <code> BCM2708_RANDOM_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_RANDOM_DESCRIPTION = 'BCM2835 Random Number Generator';</code>
+| &nbsp;
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>BCM2708_RANDOM_WARMUP_COUNT = $00040000;</code>
+| The initial numbers generated are "less random" so will be discarded
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 mailbox''' <code> BCM2708_MAILBOX_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_MAILBOX_DESCRIPTION = 'BCM2835 Mailbox';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 watchdog''' <code> BCM2708_WATCHDOG_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_WATCHDOG_DESCRIPTION = 'BCM2835 Watchdog Timer';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 20px; padding-bottom: 15px;">
+<div style="font-size: 14px; padding-left: 12px;">'''BCM2708 framebuffer''' <code> BCM2708_FRAMEBUFFER_* </code></div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>BCM2708_FRAMEBUFFER_DESCRIPTION = 'BCM2835 Framebuffer';</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+<br />
 === Type definitions ===
 ----
-''To be documented''
+'''BCM2708 SPI0'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708SPI0Device = ^TBCM2708SPI0Device;</code>
+<code>TBCM2708SPI0Device = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''SPI Properties''
+|-
+| <code>SPI:TSPIDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>CoreClock:LongWord;</code>
+| Core clock rate
+|-
+|colspan="2"|''Transfer Properties''
+|-
+| <code>Mode:LongWord;</code>
+| Mode of current transfer (BCM2708_SPI0_MODE_IRQ/BCM2708_SPI0_MODE_DMA / BCM2708_SPI0_MODE_PIO)
+|-
+| <code>Source:Pointer;</code>
+| Pointer to the source for current transfer (nil if reading only)
+|-
+| <code>Dest:Pointer;</code>
+| Pointer to the destination for current transfer (nil if writing only)
+|-
+| <code>Count:LongWord;</code>
+| Count of bytes for current transfer
+|-
+| <code>SourceRemain:LongWord;</code>
+| Source bytes remaining for current transfer
+|-
+| <code>DestRemain:LongWord;</code>
+| Destination bytes remaining for current transfer
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 BSCI2C (I2C0/1/2) device'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708BSCI2CDevice = ^TBCM2708BSCI2CDevice;</code>
+<code>TBCM2708BSCI2CDevice = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''I2C Properties''
+|-
+| <code>I2C:TI2CDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>CoreClock:LongWord;</code>
+| Core clock rate
+|-
+| <code>SDAPin:LongWord;</code>
+| GPIO pin for the SDA line
+|-
+| <code>SCLPin:LongWord;</code>
+| GPIO pin for the SCL line
+|-
+| <code>SDAFunction:LongWord;</code>
+| GPIO function for the SDA line
+|-
+| <code>SCLFunction:LongWord;</code>
+| GPIO function for the SCL line
+|-
+|colspan="2"|''Transfer Properties''
+|-
+| <code>Index:LongWord;</code>
+| Index of this device in the IRQData array (Set during device initialization)
+|-
+| <code>Mode:LongWord;</code>
+| Mode of current transfer (BCM2708_BSCI2C_MODE_WRITE/BCM2708_BSCI2C_MODE_READ)
+|-
+| <code>Data:Pointer;</code>
+| Pointer to the data for current transfer
+|-
+| <code>Count:LongWord;</code>
+| Count of bytes for current transfer
+|-
+| <code>Remain:LongWord;</code>
+| Bytes remaining for current transfer
+|-
+| <code>Error:LongBool;</code>
+| True if an error occurred during the transfer
+|-
+| <code>IgnoreNAK:LongBool;</code>
+| If True Ignore NAK responses and continue
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 BSCI2C (I2C0/1) IRQ data'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708BSCI2CIRQData = ^TBCM2708BSCI2CIRQData;</code>
+<code>TBCM2708BSCI2CIRQData = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|Note: BSC I2C devices share a single interrupt
+|-
+| <code>Count:LongWord;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>Lock:TSpinHandle;</code>
+| &nbsp;
+|-
+| <code>Devices:array[0..2] of PBCM2708BSCI2CDevice;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 SPI AUX (SPI1/2)'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708SPIAUXDevice = ^TBCM2708SPIAUXDevice;</code>
+<code>TBCM2708SPIAUXDevice = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''SPI Properties''
+|-
+| <code>SPI:TSPIDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>CoreClock:LongWord;</code>
+| Core clock rate
+|-
+|}
+</div></div>
+'''BCM2708 I2C slave buffer'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708I2CSlaveBuffer = ^TBCM2708I2CSlaveBuffer;</code>
+<code>TBCM2708I2CSlaveBuffer = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>Wait:TSemaphoreHandle;</code>
+| Data ready semaphore
+|-
+| <code>Start:LongWord;</code>
+| Index of first available buffer entry
+|-
+| <code>Count:LongWord;</code>
+| Number of available entries in the buffer
+|-
+| <code>Buffer:array[0..(BCM2708_I2CSLAVE_BUFFER_SIZE - 1)] of Byte;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 I2C slave'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708I2CSlave = ^TBCM2708I2CSlave;</code>
+<code>TBCM2708I2CSlave = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''I2C Properties''
+|-
+| <code>I2C:TI2CDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>IRQ:LongWord;</code>
+| IRQ of this device
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>Lock:TSpinHandle;</code>
+| Device lock (Differs from lock in I2C device) (Spin lock due to use by interrupt handler)
+|-
+| <code>SDAPin:LongWord;</code>
+| GPIO pin for the SDA line
+|-
+| <code>SCLPin:LongWord;</code>
+| GPIO pin for the SCL line
+|-
+| <code>SDAFunction:LongWord;</code>
+| GPIO function for the SDA line
+|-
+| <code>SCLFunction:LongWord;</code>
+| GPIO function for the SCL line
+|-
+|colspan="2"|''Transfer Properties''
+|-
+| <code>Receive:TBCM2708I2CSlaveBuffer;</code>
+| Receive Data Buffer
+|-
+| <code>Transmit:TBCM2708I2CSlaveBuffer;</code>
+| Transmit Data Buffer
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 DMA channel'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708DMAChannel = ^TBCM2708DMAChannel;</code>
+<code>TBCM2708DMAChannel = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>Host:PBCM2708DMAHost;</code>
+| DMA host this channel belongs to
+|-
+| <code>Request:PDMARequest;</code>
+| Current DMA request pending on this channel (or nil of no request is pending)
+|-
+| <code>Number:LongWord;</code>
+| The channel number of this channel
+|-
+| <code>Interrupt:LongWord;</code>
+| The interrupt number of this channel
+|-
+| <code>Registers:PBCM2835DMARegisters;</code>
+| The channel registers for configuration
+|-
+|}
+</div></div>
+'''BCM2708 DMA'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708DMAHost = ^TBCM2708DMAHost;</code>
+<code>TBCM2708DMAHost = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''DMA Properties''
+|-
+| <code>DMA:TDMAHost;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>ChannelMask:LongWord;</code>
+| Mask of available channels (Passed from GPU firmware)
+|-
+| <code>ChannelFree:LongWord;</code>
+| Bitmap of current free channels
+|-
+| <code>ChannelLock:TMutexHandle;</code>
+| Lock for access to ChannelFree
+|-
+| <code>ChannelWait:TSemaphoreHandle;</code>
+| Number of free normal channels in ChannelFree
+|-
+| <code>ChannelLite:TSemaphoreHandle;</code>
+| Number of free DMA Lite channels in ChannelFree
+|-
+| <code>ChannelBulk:TSemaphoreHandle;</code>
+| Number of free DMA Bulk channels in ChannelFree
+|-
+| <code>Channels:array[0..BCM2708_DMA_CHANNEL_COUNT - 1] of TBCM2708DMAChannel;</code>
+| Channel information for each DMA channel on the host
+|-
+| <code>EnableRegister:PLongWord;</code>
+| &nbsp;
+|-
+| <code>InterruptRegister:PLongWord;</code>
+| &nbsp;
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the host controller
+|-
+|}
+</div></div>
+'''BCM2708 PWM device'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708PWMDevice = ^TBCM2708PWMDevice;</code>
+<code>TBCM2708PWMDevice = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''PWM Properties''
+|-
+| <code>PWM:TPWMDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>Channel:LongWord;</code>
+| Channel for this device
+|-
+| <code>Scaler:LongWord;</code>
+| Scaler for Duty cycle and Period
+|-
+| <code>Pair:PBCM2708PWMDevice;</code>
+| The paired PWM device for the other channel
+|-
+|colspan="2"|''Audio Properties''
+|-
+| <code>Audio:PBCM2708PWMAudio;</code>
+| The associated PWM Audio device
+|-
+|}
+</div></div>
+'''BCM2708 PWM audio'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708PWMAudio = ^TBCM2708PWMAudio;</code>
+<code>TBCM2708PWMAudio = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Audio Properties''
+|-
+| <code>Audio:TAudioDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''PWM Properties''
+|-
+| <code>PWM0:PBCM2708PWMDevice;</code>
+| The PWM device for channel 0
+|-
+| <code>PWM1:PBCM2708PWMDevice;</code>
+| The PWM device for channel 1
+|-
+|}
+</div></div>
+'''BCM2708 GPIO'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708GPIOBank = ^TBCM2708GPIOBank;</code>
+<code>TBCM2708GPIOBank = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+| <code>GPIO:PGPIODevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+| <code>Bank:LongWord;</code>
+| &nbsp;
+|-
+| <code>Address:PtrUInt;</code>
+| &nbsp;
+|-
+| <code>PinStart:LongWord;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 GPIO device'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708GPIODevice = ^TBCM2708GPIODevice;</code>
+<code>TBCM2708GPIODevice = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''GPIO Properties''
+|-
+| <code>GPIO:TGPIODevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Lock:TSpinHandle;</code>
+| Device lock (Differs from lock in Device portion) (Spin lock due to use by interrupt handler)
+|-
+| <code>Banks:array[0..BCM2835_GPIO_BANK_COUNT - 1] of TBCM2708GPIOBank;</code>
+| &nbsp;
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 UART0'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708UART0Device = ^TBCM2708UART0Device;</code>
+<code>TBCM2708UART0Device = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''UART Properties''
+|-
+| <code>UART:TUARTDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>Address:Pointer;</code>
+| Device register base address
+|-
+| <code>ClockRate:LongWord;</code>
+| Device clock rate
+|-
+|colspan="2"|&nbsp;
+|-
+| <code>Start:LongWord;</code>
+| Index of first available buffer entry
+|-
+| <code>Count:LongWord;</code>
+| Number of available entries in the buffer
+|-
+| <code>Buffer:array[0..(BCM2708_UART0_RX_BUFFER_SIZE - 1)] of Word;</code>
+| Buffer for received data (Includes data and status)
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 SDHCI'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708SDHCIHost = ^TBCM2708SDHCIHost;</code>
+<code>TBCM2708SDHCIHost = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''SDHCI Properties''
+|-
+| <code>SDHCI:TSDHCIHost;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>FIQ:LongBool;</code>
+| &nbsp;
+|-
+| <code>SDIO:LongBool;</code>
+| &nbsp;
+|-
+| <code>WriteDelay:LongWord;</code>
+| &nbsp;
+|-
+| <code>DelayClock:LongWord;</code>
+| &nbsp;
+|-
+| <code>ShadowRegister:LongWord;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 system clock'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708SystemClock = ^TBCM2708SystemClock;</code>
+<code>TBCM2708SystemClock = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Clock Properties''
+|-
+| <code>Clock:TClockDevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 ARM clock'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708ARMClock = ^TBCM2708ARMClock;</code>
+<code>TBCM2708ARMClock = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Clock Properties''
+|-
+| <code>Clock:TClockDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>CoreClock:LongWord;</code>
+| Core clock rate
+|-
+|}
+</div></div>
+'''BCM2708 ARM timer'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708ARMTimer = ^TBCM2708ARMTimer;</code>
+<code>TBCM2708ARMTimer = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Timer Properties''
+|-
+| <code>Timer:TTimerDevice;</code>
+| &nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>CoreClock:LongWord;</code>
+| Core clock rate
+|-
+|colspan="2"|''Statistics Properties''
+|-
+| <code>InterruptCount:LongWord;</code>
+| Number of interrupt requests received by the device
+|-
+|}
+</div></div>
+'''BCM2708 random'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708Random = ^TBCM2708Random;</code>
+<code>TBCM2708Random = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Random Properties''
+|-
+| <code>Random:TRandomDevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 mailbox'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708Mailbox = ^TBCM2708Mailbox;</code>
+<code>TBCM2708Mailbox = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Mailbox Properties''
+|-
+| <code>Mailbox:TMailboxDevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 watchdog'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708Watchdog = ^TBCM2708Watchdog;</code>
+<code>TBCM2708Watchdog = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Watchdog Properties''
+|-
+| <code>Watchdog:TWatchdogDevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|}
+</div></div>
+'''BCM2708 framebuffer'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial;">
+<code>PBCM2708Framebuffer = ^TBCM2708Framebuffer;</code>
+<code>TBCM2708Framebuffer = record</code>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+|colspan="2"|''Framebuffer Properties''
+|-
+| <code>Framebuffer:TFramebufferDevice;</code>
+| style="width: 50%;"|&nbsp;
+|-
+|colspan="2"|''BCM2708 Properties''
+|-
+| <code>MultiDisplay:LongBool;</code>
+| &nbsp;
+|-
+| <code>DisplayNum:LongWord;</code>
+| &nbsp;
+|-
+| <code>DisplaySettings:TDisplaySettings;</code>
+| &nbsp;
+|-
+|}
+</div></div>
+<br />
 === Public variables ===
 ----
-''To be documented''
+''None defined''
 === Function declarations ===
@@ Line 166: / Line 1,528: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 176: / Line 1,538: @@
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function BCM2708SPI0Start(SPI:PSPIDevice;Mode,ClockRate,ClockPhase,ClockPolarity:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SPI0Start(SPI:PSPIDevice; Mode,ClockRate,ClockPhase,ClockPolarity:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 193: / Line 1,555: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 205: / Line 1,567: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 217: / Line 1,579: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 229: / Line 1,591: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 241: / Line 1,603: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 253: / Line 1,615: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 265: / Line 1,627: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 277: / Line 1,639: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Called ?rom within the interrupt handler
+| Called from within the interrupt handler
 |-
 |}
@@ Line 289: / Line 1,651: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Called ?rom within the interrupt handler
+| Called from within the interrupt handler
 |-
 |}
@@ Line 301: / Line 1,663: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 313: / Line 1,675: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 320: / Line 1,682: @@
 <br />
-'''BCM2708 BSCI2C (I2C0/1) functions'''
+'''BCM2708 BSCI2C (I2C0/1/2) functions'''
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
@@ Line 328: / Line 1,690: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 340: / Line 1,702: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 347: / Line 1,709: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CRead(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size:LongWord; var Count:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CRead(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 359: / Line 1,721: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWrite(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size:LongWord; var Count:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWrite(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 371: / Line 1,733: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWriteRead(I2C:PI2CDevice; Address:Word; Initial:Pointer; Len:LongWord; Data:Pointer; Size:LongWord; var Count:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWriteRead(I2C:PI2CDevice; Address:Word; Initial:Pointer; Len:LongWord; Data:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 383: / Line 1,745: @@
 <br />
 <div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
-<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWriteWrite(I2C:PI2CDevice; Address:Word; Initial:Pointer; Len:LongWord; Data:Pointer; Size:LongWord; var Count:LongWord):LongWord;</pre>
+<pre style="border: 0; padding-bottom:0px;">function BCM2708BSCI2CWriteWrite(I2C:PI2CDevice; Address:Word; Initial:Pointer; Len:LongWord; Data:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
 <div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
 <div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 400: / Line 1,762: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 412: / Line 1,774: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 424: / Line 1,786: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Called ?rom within the interrupt handler
+| Called from within the interrupt handler
 |-
 |}
@@ Line 436: / Line 1,798: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
-| Called ?rom within the interrupt handler
+| Called from within the interrupt handler
 |-
 |}
@@ Line 448: / Line 1,810: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | Thread submitting the current request will hold the I2C device lock
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 SPI/I2C slave functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveStart(I2C:PI2CDevice; Rate:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of I2CSlaveStart API for BCM2708 I2C slave</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use I2CSlaveStart instead.
+Rate is not applicable for I2C slave devices
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveStop(I2C:PI2CDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of I2CSlaveStop API for BCM2708 I2C slave</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use I2CSlaveStop instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveRead(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of I2CSlaveRead API for BCM2708 I2C slave</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use I2CSlaveRead instead.
+Address is not applicable for I2C slave devices
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveWrite(I2C:PI2CDevice; Address:Word; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of I2CSlaveWrite API for BCM2708 I2C slave</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use I2CSlaveWrite instead.
+Address is not applicable for I2C slave devices
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveSetAddress(I2C:PI2CDevice; Address:Word):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of I2CSlaveSetAddress API for BCM2708 I2C slave</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use I2CSlaveSetAddress instead.
 |-
 |}
@@ Line 463: / Line 1,891: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 475: / Line 1,903: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 487: / Line 1,915: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 499: / Line 1,927: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 511: / Line 1,939: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 523: / Line 1,951: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 535: / Line 1,963: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 547: / Line 1,975: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 559: / Line 1,987: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 574: / Line 2,002: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 586: / Line 2,014: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 598: / Line 2,026: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 610: / Line 2,038: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 622: / Line 2,050: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 634: / Line 2,062: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 646: / Line 2,074: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 658: / Line 2,086: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 670: / Line 2,098: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 682: / Line 2,110: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 694: / Line 2,122: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 706: / Line 2,134: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
 |-
@@ Line 718: / Line 2,146: @@
 {| class="wikitable" style="font-size: 14px; background: white;"
 |-
-! '''Note'''
+! Note
 | None documented
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 GPIO functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOStart(GPIO:PGPIODevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOStop(GPIO:PGPIODevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIORead(GPIO:PGPIODevice;Reg:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708GPIOWrite(GPIO:PGPIODevice; Reg,Value:LongWord);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOInputGet(GPIO:PGPIODevice; Pin:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOInputWait(GPIO:PGPIODevice; Pin,Trigger,Timeout:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOInputEvent(GPIO:PGPIODevice; Pin,Trigger,Flags,Timeout:LongWord; Callback:TGPIOCallback; Data:Pointer):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOInputCancel(GPIO:PGPIODevice; Pin:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOOutputSet(GPIO:PGPIODevice; Pin,Level:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOPullSelect(GPIO:PGPIODevice; Pin,Mode:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOFunctionGet(GPIO:PGPIODevice; Pin:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708GPIOFunctionSelect(GPIO:PGPIODevice; Pin,Mode:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708GPIOInterruptHandler(Bank:PBCM2708GPIOBank);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708GPIOEventTrigger(Pin:PGPIOPin);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708GPIOEventTimeout(Event:PGPIOEvent);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 UART0 functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0Open(UART:PUARTDevice; BaudRate,DataBits,StopBits,Parity,FlowControl:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceOpen API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceOpen instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0Close(UART:PUARTDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceClose API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceClose instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0Read(UART:PUARTDevice; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceRead API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceRead instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0PushRX(UART:PUARTDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0Write(UART:PUARTDevice; Buffer:Pointer; Size,Flags:LongWord; var Count:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceWrite API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceWrite instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0GetStatus(UART:PUARTDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceGetStatus API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceGetStatus instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UART0SetStatus(UART:PUARTDevice; Status:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of UARTDeviceSetStatus API for BCM2708 UART0</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use UARTDeviceSetStatus instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708UART0InterruptHandler(UART:PUARTDevice);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Interrupt handler for the BCM2708 UART0 device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708UART0Receive(UART:PUARTDevice);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Receive handler for the BCM2708 UART0 device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708UART0Transmit(UART:PUARTDevice);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Transmit handler for the BCM2708 UART0 device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708UART0EnableInterrupt(UART:PBCM2708UART0Device; Interrupt:LongWord);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Enable the specified interrupt in the interrupt mask register of a BCM2708 UART0 device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! UART
+| The BCM2708 UART0 device to enable the interrupt for
+|-
+! Interrupt
+| The interrupt to enable
+|-
+! Note
+| Caller must hold the UART lock
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708UART0DisableInterrupt(UART:PBCM2708UART0Device; Interrupt:LongWord);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Disable the specified interrupt in the interrupt mask register of a BCM2708 UART0 device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! UART
+| The BCM2708 UART0 device to disable the interrupt for
+|-
+! Interrupt
+| The interrupt to disable
+|-
+! Note
+| Caller must hold the UART lock
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 SDHCI functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostStart(SDHCI:PSDHCIHost):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostStart API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostStart instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostStop(SDHCI:PSDHCIHost):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostStop API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostStop instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostLock(SDHCI:PSDHCIHost):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostLock API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostLock instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostUnlock(SDHCI:PSDHCIHost):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostUnlock API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostUnlock instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostSignal(SDHCI:PSDHCIHost; Semaphore:TSemaphoreHandle):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostSignal API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostSignal instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostReadByte(SDHCI:PSDHCIHost; Reg:LongWord):Byte;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostReadByte API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostReadByte instead.
+|-
+! Note
+| The Broadcom document BCM2835-ARM-Peripherals page 66 states the following: Contrary to Arasans documentation the EMMC module registers can only be accessed as 32 bit registers, i.e. the two LSBs of the address are always zero. For this reason this code must simulate Byte and Word reads using LongWord reads.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostReadWord(SDHCI:PSDHCIHost; Reg:LongWord):Word;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostReadWord API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostReadWord instead.
+|-
+! Note
+| The Broadcom document BCM2835-ARM-Peripherals page 66 states the following: Contrary to Arasans documentation the EMMC module registers can only be accessed as 32 bit registers, i.e. the two LSBs of the address are always zero. For this reason this code must simulate Byte and Word reads using LongWord reads.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCIHostReadLong(SDHCI:PSDHCIHost; Reg:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostReadLong API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostReadLong instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708SDHCIHostWriteByte(SDHCI:PSDHCIHost; Reg:LongWord; Value:Byte);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostWriteByte API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostWriteByte instead.
+|-
+! Note
+| The Broadcom document BCM2835-ARM-Peripherals page 66 states the following: Contrary to Arasans documentation the EMMC module registers can only be accessed as 32 bit registers, i.e. the two LSBs of the address are always zero. For this reason this code must simulate Byte and Word writes using LongWord writes.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708SDHCIHostWriteWord(SDHCI:PSDHCIHost; Reg:LongWord; Value:Word);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostWriteWord API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostWriteWord instead.
+|-
+! Note
+| The Broadcom document BCM2835-ARM-Peripherals page 66 states the following: Contrary to Arasans documentation the EMMC module registers can only be accessed as 32 bit registers, i.e. the two LSBs of the address are always zero. For this reason this code must simulate Byte and Word writes using LongWord writes.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708SDHCIHostWriteLong(SDHCI:PSDHCIHost; Reg:LongWord; Value:LongWord);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of SDHCIHostWriteLong API for BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use SDHCIHostWriteLong instead.
+|-
+! Note
+| The source code of U-Boot and Linux kernel drivers have this comment The Arasan has a bugette whereby it may lose the content of successive writes to registers that are within two SD-card clock cycles of each other (a clock domain crossing problem). It seems, however, that the data register does not have this problem. (Which is just as well - otherwise we'd have to nobble the DMA engine too) For this reason this code must delay after each write to the registers.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708SDHCIInterruptHandler(SDHCI:PSDHCIHost);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Interrupt handler for the BCM2708 SDHCI host controller</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SDHCISetupInterrupts(SDHCI:PSDHCIHost):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Configure and enable interrupt handling for the BCM2708 SDHCI</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708MMCDeviceGetCardDetect(MMC:PMMCDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of MMC GetCardDetect for the BCM2708 which does not update the bits in the SDHCI_PRESENT_STATE register to reflect card insertion or removal</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use MMCDeviceGetCardDetect instead.
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 system clock functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SystemClockRead(Clock:PClockDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceRead API for System Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceRead instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SystemClockRead64(Clock:PClockDevice):Int64;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceRead64 API for System Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceRead64 instead.
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 ARM clock functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMClockStart(Clock:PClockDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceStart API for ARM Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceStart instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMClockStop(Clock:PClockDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceStop API for ARM Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceStop instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMClockRead(Clock:PClockDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceRead API for ARM Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceRead instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMClockRead64(Clock:PClockDevice):Int64;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceRead64 API for ARM Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceRead64 instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMClockSetRate(Clock:PClockDevice; Rate:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of ClockDeviceSetRate API for ARM Clock</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use ClockDeviceSetRate instead.
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 ARM timer functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerStart(Timer:PTimerDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceStart API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceStart instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerStop(Timer:PTimerDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceStop API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceStop instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerRead64(Timer:PTimerDevice):Int64;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceRead64 API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceRead64 instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerWait(Timer:PTimerDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceWait API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceWait instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerEvent(Timer:PTimerDevice; Flags:LongWord; Callback:TTimerCallback; Data:Pointer):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceEvent API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceEvent instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerCancel(Timer:PTimerDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceCancel API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceCancel instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerSetRate(Timer:PTimerDevice; Rate:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceSetRate API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceSetRate instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708ARMTimerSetInterval(Timer:PTimerDevice; Interval:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of TimerDeviceSetInterval API for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use TimerDeviceSetInterval instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708ARMTimerInterruptHandler(Timer:PTimerDevice);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Interrupt handler for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">procedure BCM2708ARMTimerEventTrigger(Timer:PTimerDevice);</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Event handler for ARM Timer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 random functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708RandomStart(Random:PRandomDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708RandomStop(Random:PRandomDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708RandomReadLongWord(Random:PRandomDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 watchdog functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708WatchdogStart(Watchdog:PWatchdogDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708WatchdogStop(Watchdog:PWatchdogDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708WatchdogRefresh(Watchdog:PWatchdogDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708WatchdogGetRemain(Watchdog:PWatchdogDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' To be documented</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| None documented
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 framebuffer functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferAllocate(Framebuffer:PFramebufferDevice; Properties:PFramebufferProperties):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceAllocate API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceAllocate instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferRelease(Framebuffer:PFramebufferDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceRelease API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceRelease instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferBlank(Framebuffer:PFramebufferDevice; Blank:Boolean):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceBlank API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceBlank instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferCommit(Framebuffer:PFramebufferDevice;Address:PtrUInt;Size,Flags:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceCommit API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceCommit instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferWaitSync(Framebuffer:PFramebufferDevice):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceWaitSync API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceWaitSync instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferSetOffsetEx(Framebuffer:PFramebufferDevice; X,Y:LongWord; Pan,Switch:Boolean):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceSetOffsetEx API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceSetOffsetEx instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferGetPalette(Framebuffer:PFramebufferDevice; Palette:PFramebufferPalette):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceGetPalette API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceGetPalette instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferSetPalette(Framebuffer:PFramebufferDevice; Palette:PFramebufferPalette):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceSetPalette API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceSetPalette instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferSetBacklight(Framebuffer:PFramebufferDevice; Brightness:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceSetBacklight API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceSetBacklight instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferSetCursor(Framebuffer:PFramebufferDevice; Width,Height,HotspotX,HotspotY:LongWord; Image:Pointer; Len:LongWord):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceSetCursor API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceSetCursor instead.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708FramebufferUpdateCursor(Framebuffer:PFramebufferDevice; Enabled:Boolean; X,Y:LongInt; Relative:Boolean):LongWord;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Implementation of FramebufferDeviceUpdateCursor API for BCM2708 Framebuffer</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Note
+| Not intended to be called directly by applications, use FramebufferDeviceUpdateCursor instead.
+|-
+|}
+</div></div>
+<br />
+'''BCM2708 helper functions'''
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708SPIGetDescription(Id:LongWord):String;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the device description of an SPI device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Id
+| The Id number of the SPI device (0 to 2)
+|-
+! Return
+| The correct device description suitable for passing to SPIDeviceFindByDescription
+|-
+! Note
+| The Id number supplied to this function may differ from the Ultibo device id value.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CGetDescription(Id:LongWord):String;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the device description of an I2C device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Id
+| The Id number of the I2C device (0 to 2)
+|-
+! Return
+| The correct device description suitable for passing to I2CDeviceFindByDescription
+|-
+! Note
+| The Id number supplied to this function may differ from the Ultibo device id value.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708I2CSlaveGetDescription(Id:LongWord):String;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the device description of an I2C slave device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Id
+| The Id number of the I2C slave device (Always 0)
+|-
+! Return
+| The correct device description suitable for passing to I2CSlaveFindByDescription
+|-
+! Note
+| The Id number supplied to this function may differ from the Ultibo device id value
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708PWMGetDescription(Id,Channel:LongWord):String;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the device description of a PWM device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Id
+| The Id number of the PWM device (0 or 1)
+|-
+! Channel
+| The channel number of the PWM device (0 or 1)
+|-
+! Return
+| The correct device description suitable for passing to PWMDeviceFindByDescription
+|-
+! Note
+| The Id number supplied to this function may differ from the Ultibo device id value.
+|-
+|}
+</div></div>
+<br />
+<div class="toccolours mw-collapsible mw-collapsed" style="border: 1; font-family: arial; padding-top: 0px; padding-bottom: 15px;">
+<pre style="border: 0; padding-bottom:0px;">function BCM2708UARTGetDescription(Id:LongWord):String;</pre>
+<div style="font-size: 14px; padding-left: 12px;">'''Description:''' Get the device description of a UART device</div>
+<div class="mw-collapsible-content" style="text-align: left; padding-left: 5px;">
+{| class="wikitable" style="font-size: 14px; background: white;"
+|-
+! Id
+| The Id number of the UART device (0 or 1)
+|-
+! Return
+| The correct device description suitable for passing to UARTDeviceFindByDescription
+|-
+! Note
+| The Id number supplied to this function may differ from the Ultibo device id value.
 |-
 |}

`BCM2708_SPI0_DESCRIPTION = 'BCM2835 SPI0 Master';`

`BCM2708_SPI0_MAX_SIZE = $FFFF;`

`BCM2708_SPI0_MIN_CLOCK = 3814;`	Default minimum based on the default settings from the firmware (Recalculated during open)
`BCM2708_SPI0_MAX_CLOCK = 125000000;`	Default maximum based on the default settings from the firmware (Recalculated during open)

`BCM2708_SPI0_MIN_DIVIDER = 2;`	Divider is always rounded down to an even number and a value of 0 sets the divider to 65536
`BCM2708_SPI0_MAX_DIVIDER = $FFFE;`	Divider is always rounded down to an even number

`BCM2708_SPI0_CORE_CLOCK = 250000000;`	Default core clock based on the default settings from the firmware (Requested from firmware during start)

`BCM2708_SPI0_MODE_IRQ = 0;`
`BCM2708_SPI0_MODE_DMA = 1;`
`BCM2708_SPI0_MODE_PIO = 2;`

`BCM2708_BSCI2C_MAX_SIZE = $FFFF;`

`BCM2708_BSCI2C_MIN_CLOCK = 3814;`	Default minimum based on the default settings from the firmware (Recalculated during open)
`BCM2708_BSCI2C_MAX_CLOCK = 125000000;`	Default maximum based on the default settings from the firmware (Recalculated during open)
`BCM2708_BSCI2C_DEFAULT_CLOCK = 100000;`

`BCM2708_BSCI2C_MIN_DIVIDER = 2;`	Divider is always rounded down to an even number and a value of 0 sets the divider to 32768
`BCM2708_BSCI2C_MAX_DIVIDER = $FFFE;`	Divider is always rounded down to an even number

`BCM2708_BSCI2C_CORE_CLOCK = 250000000;`	Default core clock based on the default settings from the firmware (Requested from firmware during start)

`BCM2708_BSCI2C_MODE_WRITE = 0;`
`BCM2708_BSCI2C_MODE_READ = 1;`

`BCM2708_I2CSLAVE_DESCRIPTION = 'BCM2835 I2C Slave';`

`BCM2708_I2CSLAVE_TIMEOUT = 10;`	Timeout (Milliseconds) for RX/TX wait data
`BCM2708_I2CSLAVE_BUFFER_SIZE = 1024;`	Size in bytes of the RX/TX data buffer
`BCM2708_I2CSLAVE_RX_POLL_LIMIT = 256;`	Number of times interrupt handler may poll the read FIFO

`BCM2708_DMA_DESCRIPTION = 'BCM2835 DMA';`

`BCM2708_DMA_CHANNEL_COUNT = 16;`	Total number of DMA channels (Not all are usable)

`BCM2708_DMA_LITE_CHANNELS = $7F80;`	Mask of DMA Lite channels (7 to 14)
`BCM2708_DMA_NORMAL_CHANNELS = $007E; {807F}`	Mask of normal channels (1 to 6)
`BCM2708_DMA_BULK_CHANNELS = $8001;`	Mask of DMA Bulk channels (0 and 15)

`BCM2708_DMA_SHARED_CHANNELS = $7800;`	Mask of channels with shared interrupt (11 to 14)

`BCM2708_DMA_MAX_LITE_TRANSFER = 65536;`	Maximum transfer length for a DMA Lite channel
`BCM2708_DMA_MAX_NORMAL_TRANSFER = 1073741824;`	Maximum transfer length for a normal channel

`BCM2708_DMA_MAX_STRIDE = $FFFF;`	Maximum stride value (Increment between rows) (Note this is a signed value (Min -32768/Max 32767)
`BCM2708_DMA_MAX_Y_COUNT = $3FFF;`	Maximum number of X length transfers in 2D stride
`BCM2708_DMA_MAX_X_LENGTH = $FFFF;`	Maximum X transfer length in 2D stride

`BCM2708_DMA_CB_ALIGNMENT = 32;`	Alignment required for DMA control blocks

`BCM2708_DMA_LITE_BURST_LENGTH = 2;`	Burst length for DMA Lite channels
`BCM2708_DMA_NORMAL_BURST_LENGTH = 4;`	Burst length for normal channels
`BCM2708_DMA_BULK_BURST_LENGTH = 16;`	Burst length for DMA Bulk channels

`BCM2708_PWM_MIN_PERIOD = 108;`	Default based on 19.2MHz PWM clock (Oscillator source)
`BCM2708_PWM_DEFAULT_CLOCK = 19200000;`	Default to the 19.2MHz oscillator clock

`BCM2708_GPIO_DESCRIPTION = 'BCM2835 GPIO';`

`BCM2708_GPIO_MIN_PIN = GPIO_PIN_0;`
`BCM2708_GPIO_MAX_PIN = GPIO_PIN_53;`

`BCM2708_GPIO_MAX_LEVEL = GPIO_LEVEL_HIGH;`

`BCM2708_GPIO_MAX_PULL = GPIO_PULL_DOWN;`

`BCM2708_GPIO_MIN_FUNCTION = GPIO_FUNCTION_IN;`
`BCM2708_GPIO_MAX_FUNCTION = GPIO_FUNCTION_ALT5;`

`BCM2708_GPIO_MIN_TRIGGER = GPIO_TRIGGER_LOW;`
`BCM2708_GPIO_MAX_TRIGGER = GPIO_TRIGGER_ASYNC_FALLING;`

GPIO pull up/down to BCM2835 pull up/down
`BCM2708_GPIO_PULL_MAP:array[GPIO_PULL_NONE..GPIO_PULL_DOWN] of LongWord = (`
`BCM2835_GPPUD_NONE,`
`BCM2835_GPPUD_UP,`
`BCM2835_GPPUD_DOWN);`

GPIO functions to BCM2835 functions
`BCM2708_GPIO_FUNCTION_MAP:array[BCM2708_GPIO_MIN_FUNCTION..BCM2708_GPIO_MAX_FUNCTION] of LongWord = (`
`BCM2835_GPFSEL_IN,`
`BCM2835_GPFSEL_OUT,`
`BCM2835_GPFSEL_ALT0,`
`BCM2835_GPFSEL_ALT1,`
`BCM2835_GPFSEL_ALT2,`
`BCM2835_GPFSEL_ALT3,`
`BCM2835_GPFSEL_ALT4,`
`BCM2835_GPFSEL_ALT5);`

BCM2835 functions to GPIO functions
`BCM2708_GPIO_FUNCTION_UNMAP:array[BCM2708_GPIO_MIN_FUNCTION..BCM2708_GPIO_MAX_FUNCTION] of LongWord = (`
`GPIO_FUNCTION_IN,`
`GPIO_FUNCTION_OUT,`
`GPIO_FUNCTION_ALT5,`
`GPIO_FUNCTION_ALT4,`
`GPIO_FUNCTION_ALT0,`
`GPIO_FUNCTION_ALT1,`
`GPIO_FUNCTION_ALT2,`
`GPIO_FUNCTION_ALT3);`

GPIO triggers to BCM2835 event registers
`BCM2708_GPIO_TRIGGER_MAP:array[BCM2708_GPIO_MIN_TRIGGER..BCM2708_GPIO_MAX_TRIGGER] of LongWord = (`
`GPIO_FUNCTION_IN,`
`BCM2835_GPLEN0,`
`BCM2835_GPHEN0,`
`BCM2835_GPREN0,`
`BCM2835_GPFEN0,`
`BCM2835_GPAREN0,`
`BCM2835_GPAFEN0);`

`BCM2708_UART0_DESCRIPTION = 'BCM2835 PL011 UART';`

`BCM2708_UART0_MIN_BAUD = 300;`	Default minimum of 300 baud
`BCM2708_UART0_MAX_BAUD = 187500;`	Default maximum based on the default settings from the firmware (Recalculated during open)

`BCM2708_UART0_MIN_DATABITS = SERIAL_DATA_5BIT;`
`BCM2708_UART0_MAX_DATABITS = SERIAL_DATA_8BIT;`

`BCM2708_UART0_MIN_STOPBITS = SERIAL_STOP_1BIT;`
`BCM2708_UART0_MAX_STOPBITS = SERIAL_STOP_2BIT;`

`BCM2708_UART0_MAX_PARITY = SERIAL_PARITY_EVEN;`

`BCM2708_UART0_MAX_FLOW = SERIAL_FLOW_RTS_CTS;`

`BCM2708_UART0_CLOCK_RATE = 3000000;`	Default clock rate based on the default settings from the firmware (Requested from firmware during open)

`BCM2708_UART0_RX_POLL_LIMIT = 256;`	Number of times interrupt handler may poll the read FIFO
`BCM2708_UART0_RX_BUFFER_SIZE = 1024;`

`BCM2708_EMMC_DESCRIPTION = 'BCM2835 Arasan SD Host';`

`BCM2708_EMMC_MIN_FREQ = 400000;`	Default minimum of 400KHz
`BCM2708_EMMC_MAX_FREQ = 200000000;`	Default clock rate based on the default settings from the firmware (Requested from firmware during start)

`BCM2708_SDHOST_DESCRIPTION = 'BCM2835 SDHOST';`

`BCM2708_SDHOST_MIN_FREQ = 400000;`	Default minimum of 400KHz
`BCM2708_SDHOST_MAX_FREQ = 250000000;`	Default clock rate based on the default settings from the firmware (Requested from firmware during start)
See: BCMSDHOST for the driver implementation

SPI Properties
`SPI:TSPIDevice;`
BCM2708 Properties
`Address:Pointer;`	Device register base address
`CoreClock:LongWord;`	Core clock rate

`GPIO:PGPIODevice;`
`Bank:LongWord;`
`Address:PtrUInt;`
`PinStart:LongWord;`

SDHCI Properties
`SDHCI:TSDHCIHost;`
BCM2708 Properties
`FIQ:LongBool;`
`SDIO:LongBool;`
`WriteDelay:LongWord;`
`DelayClock:LongWord;`
`ShadowRegister:LongWord;`

`BCM2708_ARM_CLOCK_DESCRIPTION = 'BCM2835 ARM Timer Clock';`

`BCM2708_ARM_CLOCK_MIN_RATE = 976562;`	Default minimum (Divider 255) based on the default settings from the firmware (Recalculated during start)
`BCM2708_ARM_CLOCK_MAX_RATE = 250000000;`	Default maximum (Divider 0) based on the default settings from the firmware (Recalculated during start)
`BCM2708_ARM_CLOCK_DEFAULT_RATE = 3968253;`	Default rate (Divider 62) based on the default settings from the firmware (Recalculated during start)

`BCM2708_ARM_CLOCK_MIN_DIVIDER = 0;`
`BCM2708_ARM_CLOCK_MAX_DIVIDER = 255;`
`BCM2708_ARM_CLOCK_DEFAULT_DIVIDER = 62;`

`BCM2708_ARM_CLOCK_CORE_CLOCK = 250000000;`	Default core clock based on the default settings from the firmware (Requested from firmware during start)

`BCM2708_ARM_TIMER_DESCRIPTION = 'BCM2835 ARM Timer';`

`BCM2708_ARM_TIMER_MIN_RATE = 244140;`	Default minimum (Divider 1023) based on the default settings from the firmware (Recalculated during start)
`BCM2708_ARM_TIMER_MAX_RATE = 250000000;`	Default maximum (Divider 0) based on the default settings from the firmware (Recalculated during start)
`BCM2708_ARM_TIMER_DEFAULT_RATE = 1000000;`	Default rate (Divider 249) based on the default settings from the firmware (Recalculated during start)

`BCM2708_ARM_TIMER_MIN_INTERVAL = 1;`
`BCM2708_ARM_TIMER_MAX_INTERVAL = $FFFFFFFF;`

`BCM2708_ARM_TIMER_MIN_DIVIDER = 0;`
`BCM2708_ARM_TIMER_MAX_DIVIDER = 1023;`
`BCM2708_ARM_TIMER_DEFAULT_DIVIDER = 249;`

`BCM2708_ARM_TIMER_CORE_CLOCK = 250000000;`	Default core clock based on the default settings from the firmware (Requested from firmware during start)

`BCM2708_RANDOM_DESCRIPTION = 'BCM2835 Random Number Generator';`

`BCM2708_RANDOM_WARMUP_COUNT = $00040000;`	The initial numbers generated are "less random" so will be discarded

I2C Properties
`I2C:TI2CDevice;`
BCM2708 Properties
`Address:Pointer;`	Device register base address
`CoreClock:LongWord;`	Core clock rate
`SDAPin:LongWord;`	GPIO pin for the SDA line
`SCLPin:LongWord;`	GPIO pin for the SCL line
`SDAFunction:LongWord;`	GPIO function for the SDA line
`SCLFunction:LongWord;`	GPIO function for the SCL line
Transfer Properties
`Index:LongWord;`	Index of this device in the IRQData array (Set during device initialization)
`Mode:LongWord;`	Mode of current transfer (BCM2708_BSCI2C_MODE_WRITE/BCM2708_BSCI2C_MODE_READ)
`Data:Pointer;`	Pointer to the data for current transfer
`Count:LongWord;`	Count of bytes for current transfer
`Remain:LongWord;`	Bytes remaining for current transfer
`Error:LongBool;`	True if an error occurred during the transfer
`IgnoreNAK:LongBool;`	If True Ignore NAK responses and continue
Statistics Properties
`InterruptCount:LongWord;`	Number of interrupt requests received by the device

Note: BSC I2C devices share a single interrupt
`Count:LongWord;`
`Lock:TSpinHandle;`
`Devices:array[0..2] of PBCM2708BSCI2CDevice;`

`Wait:TSemaphoreHandle;`	Data ready semaphore
`Start:LongWord;`	Index of first available buffer entry
`Count:LongWord;`	Number of available entries in the buffer
`Buffer:array[0..(BCM2708_I2CSLAVE_BUFFER_SIZE - 1)] of Byte;`

`Host:PBCM2708DMAHost;`	DMA host this channel belongs to
`Request:PDMARequest;`	Current DMA request pending on this channel (or nil of no request is pending)
`Number:LongWord;`	The channel number of this channel
`Interrupt:LongWord;`	The interrupt number of this channel
`Registers:PBCM2835DMARegisters;`	The channel registers for configuration

DMA Properties
`DMA:TDMAHost;`
BCM2708 Properties
`ChannelMask:LongWord;`	Mask of available channels (Passed from GPU firmware)
`ChannelFree:LongWord;`	Bitmap of current free channels
`ChannelLock:TMutexHandle;`	Lock for access to ChannelFree
`ChannelWait:TSemaphoreHandle;`	Number of free normal channels in ChannelFree
`ChannelLite:TSemaphoreHandle;`	Number of free DMA Lite channels in ChannelFree
`ChannelBulk:TSemaphoreHandle;`	Number of free DMA Bulk channels in ChannelFree
`Channels:array[0..BCM2708_DMA_CHANNEL_COUNT - 1] of TBCM2708DMAChannel;`	Channel information for each DMA channel on the host
`EnableRegister:PLongWord;`
`InterruptRegister:PLongWord;`
Statistics Properties
`InterruptCount:LongWord;`	Number of interrupt requests received by the host controller

PWM Properties
`PWM:TPWMDevice;`
BCM2708 Properties
`Address:Pointer;`	Device register base address
`Channel:LongWord;`	Channel for this device
`Scaler:LongWord;`	Scaler for Duty cycle and Period
`Pair:PBCM2708PWMDevice;`	The paired PWM device for the other channel
Audio Properties
`Audio:PBCM2708PWMAudio;`	The associated PWM Audio device

Audio Properties
`Audio:TAudioDevice;`
PWM Properties
`PWM0:PBCM2708PWMDevice;`	The PWM device for channel 0
`PWM1:PBCM2708PWMDevice;`	The PWM device for channel 1

Difference between revisions of "Unit BCM2708"

Latest revision as of 06:19, 11 April 2025

Contents

Description

Constants

Type definitions

Public variables

Function declarations

Navigation menu

Search

GPIO Properties
`GPIO:TGPIODevice;`
BCM2708 Properties
`Lock:TSpinHandle;`	Device lock (Differs from lock in Device portion) (Spin lock due to use by interrupt handler)
`Banks:array[0..BCM2835_GPIO_BANK_COUNT - 1] of TBCM2708GPIOBank;`
Statistics Properties
`InterruptCount:LongWord;`	Number of interrupt requests received by the device

UART Properties
`UART:TUARTDevice;`
BCM2708 Properties
`Address:Pointer;`	Device register base address
`ClockRate:LongWord;`	Device clock rate

`Start:LongWord;`	Index of first available buffer entry
`Count:LongWord;`	Number of available entries in the buffer
`Buffer:array[0..(BCM2708_UART0_RX_BUFFER_SIZE - 1)] of Word;`	Buffer for received data (Includes data and status)
Statistics Properties
`InterruptCount:LongWord;`	Number of interrupt requests received by the device

Clock Properties
`Clock:TClockDevice;`
BCM2708 Properties
`CoreClock:LongWord;`	Core clock rate

Timer Properties
`Timer:TTimerDevice;`
BCM2708 Properties
`CoreClock:LongWord;`	Core clock rate
Statistics Properties
`InterruptCount:LongWord;`	Number of interrupt requests received by the device

Framebuffer Properties
`Framebuffer:TFramebufferDevice;`
BCM2708 Properties
`MultiDisplay:LongBool;`
`DisplayNum:LongWord;`
`DisplaySettings:TDisplaySettings;`

UART	The BCM2708 UART0 device to enable the interrupt for
Interrupt	The interrupt to enable
Note	Caller must hold the UART lock

UART	The BCM2708 UART0 device to disable the interrupt for
Interrupt	The interrupt to disable
Note	Caller must hold the UART lock

Note	Not intended to be called directly by applications, use SDHCIHostReadByte instead.
Note	The Broadcom document BCM2835-ARM-Peripherals page 66 states the following: Contrary to Arasans documentation the EMMC module registers can only be accessed as 32 bit registers, i.e. the two LSBs of the address are always zero. For this reason this code must simulate Byte and Word reads using LongWord reads.

Id	The Id number of the SPI device (0 to 2)
Return	The correct device description suitable for passing to SPIDeviceFindByDescription
Note	The Id number supplied to this function may differ from the Ultibo device id value.

Id	The Id number of the I2C device (0 to 2)
Return	The correct device description suitable for passing to I2CDeviceFindByDescription
Note	The Id number supplied to this function may differ from the Ultibo device id value.