Difference between revisions of "Unit BootRPi4"

Latest revision as of 01:15, 22 April 2022

Return to Unit Reference

Description

Ultibo Initialization code for Raspberry Pi 4

The boot loader on the Raspberry Pi 4 will load this code at address 0x00008000 onwards and set the following registers before jumping to this code.

R0 - Zero

R1 - Machine Type (Raspberry Pi 4 or BCM2711 = 0x0C42)

R2 - Address of the ARM Tags structure (Normally 0x0100)

On entry to this code the processor will be in the following state:

World - Non Secure (Firmware causes a switch to Non Secure before jumping to Startup code)

Mode - Hypervisor (ARM_MODE_HYP)

MMU - Disabled

FPU - Disabled

Data Cache - Disabled

Instruction Cache - Enabled (Firmware enabled during boot)

Branch Predication - Disabled

Unaligned Data Access - Enabled (Always enabled on ARMv8)

SMP Coherence - Enabled (Firmware enabled during boot)

The firmware also does initial configuration of the GIC as follows:

Distributor interface enabled for Group 0 and Group 1 interrupts

CPU interface enabled for Group 1 interrupts

All interrupts routed to Group 1

All secondary CPUs will be executing a loop reading their designated local peripherals mailbox0 and waiting for a start address to begin execution.

Ultibo switches from Hypervisor mode to Supervisor mode during initial boot.

If the configuration option ARMSecureBoot is set to 1 then Ultibo switches the processor back to Secure world during initial boot (see note below).

Ultibo then switches the processor to System mode for all operations and remains in either the Secure or Non Secure World as per the option above.

The initialization process enables the MMU, FPU, L1 Cache and other performance optimizations.

Note that this code is currently almost identical to the Raspberry Pi 2 and 3 boot code but has been separated to allow for supporting 64 bit mode on the ARMv8 in future. Ultibo currently runs the RPi4 in 32 bit mode which is almost identical to ARMv7.

ARM64 support on Raspberry Pi 4

A 64 bit loader is included in the firmware and if the file kernel8.img exists in the boot partition the firmware will attempt to boot this image in 64 bit mode.

The boot loader on the Raspberry Pi 4 will load this code at address 0x00080000 onwards and set the following registers before jumping to this code.

X0 - Address of the ARM Tags or Device Tree structure

X1 - Zero

X2 - Zero

X3 - Zero

On entry to this code in 64 bit mode the processor will be in the following state:

World - Non Secure (Firmware causes a switch to Non Secure before jumping to Startup code)

Mode - EL2 (Hypervisor)

MMU - Disabled

FPU - Disabled

Data Cache - Disabled

Instruction Cache - Enabled (Firmware enabled during boot)

Branch Predication - Disabled

Unaligned Data Access - Enabled (Always enabled on ARMv8)

SMP Coherence - Enabled (Firmware enabled during boot)

The boot loader also does initial configuration of the GIC as follows:

Distributor interface enabled for Group 0 and Group 1 interrupts CPU interface enabled for Group 1 interrupts All interrupts routed to Group 1

All secondary CPUs will be executing a loop reading a memory address at 0xd8/e0/e8/f0 and waiting for a start address to begin execution.

Returning to Secure World:

The Raspberry Pi 4 firmware always switches to Non Secure world in order to:

a) Reset CNTVOFF (Virtual Offset register) to zero

b) Switch to Hypervisor mode (Firmware later than 2/10/2015)

It is not normally possible (by design) to return from the Non Secure world to the Secure world except by invoking the Secure Monitor which then handles any requests in the Secure world.

However due to the fact that this switch is performed by the boot loader code (loaded between 0x00000000 and 0x000000FF by the firmware) and that the code appears to set the secure, non secure and monitor vector base addresses to 0x00000000 and because all memory is writable from non secure at boot (the MMU is disabled) then the option exists to return to the Secure world as follows:

-Install a new Secure Monitor Call vector at the appropriate point in the vector table

-Clean the data cache by Modified Virtual Address at address 0x00000000

-Perform a data synchronisation barrier

-Invalidate the entire instruction cache

-Perform a data synchronisation barrier

-Perform an instruction synchronisation barrier

-Perform a Secure Monitor Call (SMC)

-From within the newly installed Secure Monitor Call read the Secure Configuration Register (SCR) mask off the Non Secure (NS) bit, rewrite the SCR and then return to Supervisor mode.

Secondary cores also switch back to the Secure world using the same technique however they do not need to install the new SMC vector and instead use the one installed by the primary core.

Firmware changes from October 2020 disable the ability to perform the SMC instruction from non secure mode which means this technique will no longer work with the default firmware. To allow continued support for returning to the Secure world a custom ARM boot stub is now included with Ultibo that allows the SMC instruction to be performed.

This custom stub contains a marker that allows the boot process to detect it and disable the attempt to switch back to the Secure world if the default boot stub is used instead.

As the default boot stub continues to evolve in response to demands from the Linux community this technique will allow Ultibo to continue to provide the features we want without having to make frequent changes to combat items that are beyond our control.

Thanks to the Circle project for introducing the custom boot stub technique to work around these changes.

Constants

None defined

Type definitions

None defined

Public variables

None defined

Function declarations

Boot functions

procedure Startup; assembler; nostackframe; public name '_START';

procedure Vectors; assembler; nostackframe;

procedure SecureVectors; assembler; nostackframe;

procedure SecureMonitor; assembler; nostackframe;

procedure StartupSwitch; assembler; nostackframe;

procedure StartupSecure; assembler; nostackframe;

procedure StartupHandler; assembler; nostackframe;

Return to Unit Reference