Difference between revisions of "Unit HyperPixel"
(Created page with "Return to Unit Reference === Description === ---- ''To be documented'' === Constants === ---- ''To be documented'' === Type definitions === ---- ''To...") |
|||
| Line 5: | Line 5: | ||
---- | ---- | ||
| − | '' | + | |
| + | '''Pimoroni HyperPixel TFT Display Driver unit''' | ||
| + | |||
| + | The HyperPixel is a TFT display produced by Pimoroni for use with the Raspberry Pi. It uses the DPI (Display Parallel Interface) which is directly supported by the | ||
| + | VideoCore GPU and means that unlike other TFT displays using SPI or similar interfaces it supports hardware accelerated graphics in the same way as HDMI or DSI displays. | ||
| + | |||
| + | The HyperPixel is available in several versions including a 4.0 inch rectangular, a 4.0 inch square and 2.1 inch round. Each version requires a slightly different set of instructions to initialize it and this unit provides the correct sequence for each of these displays. | ||
| + | |||
| + | To use this unit simply include it in your application and then call the function HyperPixelInitialize() as early as possible passing the appropriate model as the only parameter to the function. Once initialized successfully the HyperPixel display will be available via the standard framebuffer functions and also via the VC4 accelerated graphics options such as OpenVG, OpenGLES, OpenMAX and MMAL. | ||
| + | |||
| + | It is important to remember that no other devices should be enabled while using the HyperPixel display as it consumes almost all of the available GPIO pins. So it is not possible to use UART, I2C, SPI, PWM etc when the HyperPixel is installed. | ||
| + | |||
| + | The touch screen controller varies between models and this unit creates and initializes the appropriate one for the model selected. All touch screen devices are I2C based however as it is not possible to utilize the hardware I2C controller (see note above) a software I2C host is created to provide access to the touch screen. | ||
| + | |||
| + | The touch events generated from the device can be read from the normal touch or mouse API functions in much the same way as any other touch or mouse device. | ||
| + | |||
| + | In order to enable the HyperPixel display you need to add the appropriate settings to your config.txt file as follows: | ||
=== Constants === | === Constants === | ||
Revision as of 03:54, 29 November 2021
Return to Unit Reference
Description
Pimoroni HyperPixel TFT Display Driver unit
The HyperPixel is a TFT display produced by Pimoroni for use with the Raspberry Pi. It uses the DPI (Display Parallel Interface) which is directly supported by the VideoCore GPU and means that unlike other TFT displays using SPI or similar interfaces it supports hardware accelerated graphics in the same way as HDMI or DSI displays.
The HyperPixel is available in several versions including a 4.0 inch rectangular, a 4.0 inch square and 2.1 inch round. Each version requires a slightly different set of instructions to initialize it and this unit provides the correct sequence for each of these displays.
To use this unit simply include it in your application and then call the function HyperPixelInitialize() as early as possible passing the appropriate model as the only parameter to the function. Once initialized successfully the HyperPixel display will be available via the standard framebuffer functions and also via the VC4 accelerated graphics options such as OpenVG, OpenGLES, OpenMAX and MMAL.
It is important to remember that no other devices should be enabled while using the HyperPixel display as it consumes almost all of the available GPIO pins. So it is not possible to use UART, I2C, SPI, PWM etc when the HyperPixel is installed.
The touch screen controller varies between models and this unit creates and initializes the appropriate one for the model selected. All touch screen devices are I2C based however as it is not possible to utilize the hardware I2C controller (see note above) a software I2C host is created to provide access to the touch screen.
The touch events generated from the device can be read from the normal touch or mouse API functions in much the same way as any other touch or mouse device.
In order to enable the HyperPixel display you need to add the appropriate settings to your config.txt file as follows:
Constants
To be documented
Type definitions
To be documented
Public variables
To be documented
Function declarations
To be documented
Return to Unit Reference
